Search Documents

By Rajendra Singh

Underground depillaring of contiguous coal seams/sections is a difficult problem, which becomes even more complex if the interburden/parting between them is thin. Conventionally, the depillaring with caving of contiguous seams/sections is done in descending order. However, if the parting is thin, the influence of the top sections/seams working over the standing pillars of bottom the sections/seams becomes extremely important for the safety and optimal exploitation of coal. Field investigations were carried out at Nowrozabad East mine where superimposed pillars of the Johilla top section were depillared above the developed pillars of the Johilla bottom section with a 3 m thick parting between the two sections. The competency of the 3 m thick parting (which consists of alternate layers of shale, sandstone and shaly sandstone) was improved by reinforcement (underpinning). The strata control investigations did not show any considerable instability problem of the 3 m thick reinforced parting and pillars of the bottom section due to top section depillaring. On the basis of this field investigation and a laboratory study on simulated models, simultaneous extraction of both the sections, along with reinforcement of the parting, was suggested for the geomining conditions of the Johilla top and bottom sections. Adopting the suggested simultaneous depillaring process, two sub panels of Johilla top and bottom sections have successfully been extracted without any strata control problem. This paper presents this case study along with the results of the strata monitoring conducted to evaluate performance of the underground structures during the field trial.

Jan 1, 2004

By Chris D. Shewmaker

So you want to install 2,600 augered cast-in-place piles, about 155,000 lineal feet, in 33 working days? It can be done. The Public Service Enterprise Group (PSEG) decided to build a combined cycle power plant in Lawrenceburg, Indiana. PSEG selected Fluor Constructors Indiana, L.P. to design and build the plant. Fluor Constructors, in turn, selected Richard Goettle, Inc. to install the piles. The initial plan was to install the 2,600 piles in 33 days, working six (6) ten hour days per week. After successfully installing and performing four pile load tests - up to 300 ton capacity - we set out to complete the work and meet the aggressive schedule. After three weeks of installing an average of 75 piles a day with three drill rigs, Fluor relaxed the schedule because we were so far ahead of their projected construction sequence. We elected to continue drilling on a ten-hour day, five days a week schedule. In all, we installed nearly 2,800 piles, totaling 175,000 lineal feet, in about 47 days.

Jan 1, 2004

By D. C. Panigrahi

Extensive field studies have been carried out to investigate the pillar fire problems in one coal mine in India. A Thermal IR gun and a Thermovision camera have been employed for thermal scanning to assess the state of heating in selected pillars. Special sampling set-ups have been designed to collect gas samples from the holes drilled into the selected pillars and the multigas detector is used to analyse the composition of samples in situ. In order to predict the spontaneous heating in coal pillars, different gas ratios have been calculated and it has been observed that some of the established gas ratios, viz. Graham?s ratio, Young?s ratio etc. have resulted in negative values in samples containing high amounts of methane. The modified gas ratios have been proposed which will be useful for predicting the pillar fires. These ratios may also be used for assessing the condition of fires in sealed-off areas.

Jan 1, 2004

By J. L. Floyd

The Trapper Mine is a large surface coal operation located in northwestern Colorado US. The coal seams at the mine dip an average of 8 degrees so, historically, their dragline pits have been orien-tated parallel to the dip of the coal seam to balance stripping ratios. However, the mine plan in the future G and Z pits is designed to take advantage of pit orientations that are parallel to the strike of the coal. During the initial presplit and cast blasts in G pit, significant slope damage occurred. This damage included the opening of joints and tension cracking. There was also block movement directly above the L coal seam, which is the main plane of weakness in the slope. A detailed site evaluation was conducted to develop specific blast design modifications to protect the slopes during future blasting. The modified de-signs successfully controlled vibration levels during the blasting of the Z pit box cut. This paper includes a review of the blast vibration related factors that influence slope stability along with a detailed discussion of the field tests and design modifications developed.

Jan 1, 2004

By T. Watanabe, S. Hayashi, M. Hayashi, K. Nagata, H. Fukuyama

Chemical states of fluorine in CaO-SiO2-CaF2glasses in a composition range of CaO/SiO2=0.5?1.3 and 5?25 mol%CaF2have been investigated by 19F solid-state NMR with and without MAS. The isotropic chemical shifts of the glasses are close to those of cuspidine crystal (59.4 and64.3 ppm with respect to C6F6) and CaF2crystal (58.6 ppm). The fluoride ions are coordinated with four or less than four calcium ions in this composition range. The chemical shifts move to the lower frequency with an increase in the CaF2content, whereas those are not affected by theCaO/SiO2ratio. The ionic distance between calcium and fluoride ions increases with an increase in the CaF2content. The chemical state of fluorine is not disturbed by the degree of polymerization of the silicate network. Comparing the MAS and static NMR spectra, the second moment attributed to 19F-19F dipole-dipole interaction has been estimated. The values of the glasses range over 3.1?7.3107Hz2andthose are larger than the calculated value of cuspidine crystal. This indicates that fluoride ions form Ca-F clusters in the glasses and that the size of clusters increases with increasing the CaF2content. Keywords: chemical state of fluoride ion, CaO-SiO2-CaF2glass, solid state 19F NMR spectroscopy

Jan 1, 2004

By M. C. Mound, E. Gallestey, C. Colbert

Continuous operating performance and high profit is one of the major concerns in the mining industry. Information systems are expected to reinforce and enable conformance to these requirements. The companion efforts of business management and production information systems press for tighter integration to avoid over-laps, multiple instances of similar data, and expensive maintenance of databases. Implementation of advanced intelligent systems throughout a mine operation can reduce costs, optimize investment and create a shorter payback via conversion of the data accumulated by field and process devices into information, and subsequently, into decisions. However, in order to harness the potential power inherent in these intelligent devices, adequate and flexible modular knowledge-based solutions are required. Fortunately, there has been at least one such practical response to this challenge, namely the ABB IndustrialIT portfolio. With these tools in place, production efficiency is reached via integration of process, production, and quality information. Moreover, they permit immediate detection and remedial action to changes to process and boundary condition variables. Finally, using advanced optimization techniques supported by dedicated mathematical models, they allow for economic process optimization (process set points and coordination thereof, energy management, production planning, energy supply contract optimization, etc) of the plant as a whole.

Jan 1, 2004

By V. T. McLemore

The mining industry is at a crossroad. To sustain our technically based society, demands for commodities are increasing, and exploration for these commodities is a must. The debate is between sustainable development and the status quo and begins with exploration, where it is determined if a mineralized area contains enough potential ore to be mined economically. Mineral deposits are relatively rare and depend upon certain natural geologic conditions to form and may not always occur in locations that are most suitable to society. Exploration can be compatible with environmental protection and social responsibility, but difficult challenges face the industry to develop a property that is environmentally, economically, and socially responsible.

Jan 1, 2004

By K. Morita, N. Sano

Thermodynamic properties of chromium oxides in molten slags are very important for optimization of stainless steel refining processes as well as reduction processes of chromium ores. The solubility of chromite into molten slags has been found to vary considerably with oxygen partial pressure and slag composition in former studies by the authors. In the present study, activity data and redox equilibria of chromium oxides measured under moderately reducing conditions, PO2= 6.95x10–11atm, at 1873 K are summarized. For the CaO-SiO2-CrOXsystem, the activity coefficient of chromium oxide increased with increasing basicity, and the optimized slag composition for stainless steel refining is assessed as that saturated with CaCr2O4and Cr2O3usingthe phase relations determined. On the other hand, the presence of MgO and Al2O3brings about different behaviour of chromium oxide activity and redox equilibiria and the 44 mass per centCaO-39 mass per cent SiO2-11 mass per cent Al2O3-6 mass per cent MgO slag is recommended toreduce the chromium oxidation loss in the practical stainless steel refining process at 1873 K. Keywords: chromium, activity, stainless steel, AOD, VOD, oxidation loss, redox, CaO-SiO2-Al2O3-MgO slag

Jan 1, 2004

By P. J. D. Lloyd

At first I read this paper with interest, which grew to fascination, and ended up with horror. Such reactions to a supposedly scientific contribution are rare, and I believe the coal mining community must be warned in the strongest possible terms against the recommendations that this paper makes. The paper purports to have assessed statistically two sets of data on methane concentrations recorded in the return air from Turkish longwalls. The first set of data, from their Table I, is reproduced in Table I below. The data have been rearranged in classes to indicate the underlying distribution. While there is only limited data (N=33), the distribution looks as if it could be the sum of two normal distributions with means around 0.5 and 0.8, or possibly a log-normal distribution. What is quite clear is that it is nota single normal distribution.

Jan 1, 2004

By Georgene Renner, William R. Yernberg, Steve Kral

Allmand exhibited its LSC 100Light Sequence Commander, the mining industry’s first automatic lighting and command control system. The system is available with all of Allmand’s portable light towers. The LSC100 uses a preset photocell sensor that allows the light tower to be automatically turned on or off. At dusk, the sensor engages the power unit and then activates the light. At dawn, the sensor automatically shuts off the light. The unit also features an eight-event digital timer that allows eight separate sequences daily. The LSC100’s sequenced light control ensures that the engine is started before the lights are turned on or off. This prevents possible generator damage that can occur if the unit is powered down under load. Also, a low-fuel shutdown sequence helps protect the generator from damage by automatically shutting down the unit when the fuel level reaches 10 percent. And the LSC100’s smart circuitry senses engine water temperature during startup, determines the glow-plug time requirement and schedules repeat intervals, if necessary, to start the diesel engine.

Jan 1, 2004

By D. Xie

An in situ gravimetric technique based on wetting and capillary action principles has been used to investigate the wetting and penetration of synthesized alumina samples and commercial magnesia spinel refractories by CaO-SiO2-Al2O3-Fe2O3slags. Synthetic slags of 40CaO-40SiO2-20Al2O3 (in weight per cent) with 0 to 9 weight per cent Fe2O3were used and the experiments were conducted at temperatures 1370 to 1470ºC under argon. The contact time between the sample and the slag was 30 minutes. The results show that the wetting and penetration are enhanced by the iron oxide addition in the slags. Addition of Fe2O3from 0 to 9 weight per cent resulted in a significant increase in the slag penetration into the magnesia spinel refractory by a factor of about 7 and a moderate increase in the synthesized alumina by about 60 per cent. The addition of Fe2O3enhanced the wetting (??cos?, where ? is the surface tension of the slag and the contact angle between the slag and the refractory) by 5 to 18 per cent. An increase in temperature from 1370ºC to 1470ºC resulted in a significant increase in the penetration of a 6 weight per cent Fe2O3slag in the alumina and magnesia samples by a factor of4 to 5 and a decrease in wetting by approximately 30 per cent. Keywords: refractories, slag penetration, wetting.

Jan 1, 2004

By Jim Gunderson

Jan 1, 2004

By M. Tangstad, B. Monsen, H. Midtgaard

The increased attention towards reducing emissions of fossil CO2 due to its potential global warming effect has resulted in a focus on renewable resources, as charcoal. Since charcoal is produced from growing wood it does not contribute to global warming. This paper gives a brief review of consequences of and reasons for using charcoal in the silicomanganese (SiMn) production. Results are presented from practical SiMn smelting experiments, on a pilot scale, using charcoal as reduction material and comparing with coke. As slag- and CO2-reactivity are important for furnace performance these features have also been measured.

Jan 1, 2004

By T. Markus, K. Hilpert

Discharge vessels of advanced light sources are made of translucent polycrystalline Al2O3(PCA).These tubes contain salt mixtures, which essentially consist of metal halides. The salt mixture is present as a melt at the coldest spot of the vessel under operating conditions and vaporizes partly. The temperatures of the coldest spot range between 1200 K and 1300 K, depending on the lamp performance. The maximum wall temperatures range up to 1500 K and for special purposes up to1700 K. Important constituents of the melt are alkali halides AX (A = Na, Cs, X= Br, I) and rare earth metal halides LnX3(Ln = Dy, Ho, Tm). Severe corrosion attack on the wall material is observed in the PCA discharge vessels. The aim of this work is to elucidate the corrosion mechanism. Annealing experiments under well defined temperatures were carried out in order to understand the complex chemical corrosion processes. Two different annealing vessels were used, one for experiments under isothermal conditions with a temperature of 1473 K and one for experiments with a linear temperature gradient from 1450 K to 1600 K. The vessels were filled with salt mixtures of different compositions and annealed for 1000 h. The corrosion attack was characterised by XRD, analytical electron microscopy, high temperature mass spectrometry, and chemical analysis of the salt melts. The results of our investigations show that the corrosion attack is caused by vapour species and by the salt melt. The most severe corrosion is observed in vessels filled with mixtures of alkali halides and rare earth metal halides. No corrosion of the alumina is practically observed if pure alkali halides or pure rare earth metal halides are present in the annealing vessel. Keywords: thermodynamic, corrosion, lamps, metal halide salt

Jan 1, 2004

The Sams Creek gold deposit near Takaka in northwest Nelson was discovered in 1974 by CRA Exploration (CRAE) geologists. CRAE recognised the potential of the area and subsequently undertook a comprehensive exploration programme of geological mapping, soil and rock-chip sampling, geophysical surveys and diamond drilling. Exploration defined sporadic gold mineralisation contained entirely within a deformed and hydrothermally altered, peralkaline granite porphyry dyke with a seven kilometre strike length, and up to 60 m thickness. Rock chip samples indicated extensive and economically significant gold grades over approximately one kilometre strike of the dyke at Main Zone prospect. CRAE completed 30 diamond drill holes at this prospect and defined a limited resource. Oceana Gold Limited recommenced active exploration at the Sams Creek Project in late 2002, focusing on improving the geological understanding and known resource at Main Zone. Completion of 1041 m diamond drilling successfully increased the estimated resource to 10.7 Mt @ 2.12 g/t Au containing 729 000 oz at a 0.7 g/t cut off. A further campaign of 1560 m diamond drilling was undertaken in 2003 - 2004 to extend the resource and test the continuity of high grade mineralised zones. Deeper intersections of the porphyry dyke indicated geometrical complexity and grade variability similar to that observed at shallow levels. Recent research suggests that Sams Creek can be geologically classified as a variant of intrusion-related gold systems, and therefore comparable to some other, very large gold deposits. However, due to the rugged terrain and dyke geometry, surface drilling is reaching the limits of viability at Main Zone. If infill drilling continues to be successful then an underground decline may be developed to facilitate further exploration. Potential also exists along strike, where other significant gold anomalies are known but largely untested by drilling.

Jan 1, 2004

By Ann Barron

For millions of people, cold weather is a fact of line – and one that can make a major challenge out of just getting to work. But for those working in the blasting industry, a number of obstacles are created when old man winter blows in. In addition to the obvious concerns regarding personal protection, Mother Nature can throw some very nasty weather at the blasting crew trying to travel with explosives products from the magazine site to the job site. As such, divers need to be familiar with cold, ice, and snow driving conditions both on and off the blast site. It’s critical to know what to expect before you leave. Keep informed of the latest weather and road conditions as they change often; it will help you make the right choice in clothing and driving habits. Remember bridges and overpasses will freeze first even in temperatures above or near the freezing mark due to the effects of wind chill. Plan to take extra time to and from the job site.

Jan 1, 2004

By J F. Seale

The design of the settling pond for the Malvern Hills opencast coal project was based on a primary requirement to control runoff and sediment generated from the immediate 6 ha mine catchment, which included two seepages from old underground workings. The pond has been particularly effective in controlling turbidity in the outflow water, with the consent limit of 50 NTU being met on all but one occasion and normal levels of discharge less than 10 NTU. Water quality testing carried out at the time of consenting indicated that there were no acid-generation issues with the proposed mine site in dominant mudstone strata of the Broken River Formation, and that water from the old mine workings was near-neutral in terms of pH and well-buffered. However, it became apparent over the very dry summer of 2003 - 2004 that slaking of the exposed mudrocks in the mine batters was resulting in significant acidity generation, and outflow pH levels were well below the consent limit of 6.5 during and following periods of rainfall. Although these acidity problems have been remediated in the short-term by the use of lime products, it is clear that a programme of lithotype characterisation for AMD should have been undertaken and this has now been implemented. Design of long-term acid drainage control measures is being carried out, and will probably be based around the use of hydrated lime for pH control with enhancement of natural wetlands.

Jan 1, 2004

By A. Aitio

Sustainable development is one of the central themes of the work of the World Health Organization; chemical safety is one of its important components. For more than 25 years, WHO has had specialized units for assisting member countries in dealing with their problems in chemical safety. For one of the units involved, International Programme on Chemical Safety, a reorientation is in progress to make best use of existing resources, and to prioritise the work to optimally correspond to the needs of the member countries. The risk assessment work of IPCS, and specifically, the work on chromium and chromium compounds, are discussed.

Jan 1, 2004

By S. Rolseth, J. Thonstad

The traditional electrolyte for aluminium electrolysis is based on molten cryolite (Na3AlF6), acting as solvent for the raw material, alumina (Al2O3). Over the years there has been a trend to increase the content of excess aluminium fluoride (AlF3) to the cryolite-based electrolyte, in order to enhance the current efficiency of the process. In most cases one has ended up at 11?13 wt% excess AlF3because higher contents makes it difficult to control the heat balance of the process. This problem may be overcome if sensors are developed that will allow online control of electrolyte temperature and composition, and we may then see a surge towards still higher AlF3contents. In the development of new anode materials to replace the carbon anode with inert, oxygen-evolving anodes, focus is on anode corrosion, and a low electrolyte temperature is then highly desirable. While the conventional process operates at around 960°C, electrolyte temperatures as low as 750°C are being tested. This is achieved by having large excess contents of AlF3(40 wt%). The consequences of using such electrolyte compositions are discussed.

Jan 1, 2004

By A. V. Pavlov, A. V. Dubachev, K. L. Kossyrev

The purpose of the given research was to investigate the possibility of high-carbon ferrochromium refining to remove harmful impurities as a result of metal treatment by slag mixtures on the basis of the CaO-MgO-SiO2system. The final conclusions were drawn from experimental results. It was shown that the treatment of high-carbon ferrochromium by SiO2-MgO-CaO slag mixtures with additions of chromium sinter or iron-ore concentrate removes carbon, sulphur and phosphorus from the metal. A mechanism of phosphorus removal from a melt to a gas phase is proposed.

Jan 1, 2004