Search Documents

By Vern Pfannenstiel

Jan 1, 2005

By C. C. Oosthuizen

Paper written on project work carried out in partial fulfilment of Technikon Practical Training Frank shaft is mining both Merensky reef and UG2 reef. The Merensky orebody is almost depleted and this was the reason for starting to mine the UG2 ore reserves. It was decided to mine the UG2 orebody with trackless equipment using a bord and pillar mining method. Frank shaft has been mining the UG2 orebody for nearly 5 years. The T-cut mining method was introduced to see if it could improve the grade of the run of mine (ROM) as well the extraction percentage.

Jan 1, 2005

By Michelle Lostra, Red Blanchette, Jan Babendererde, Greg Colzani

The City of Portland’s Westside CSO Project is constructing a deep tunnel system to reduce combined sewer overflows (CSO) from entering the Willamette River. Several kilometers of microtunneled pipelines connect the existing system to the new tunnel. The alignments encountered a variety of ground conditions, including fill, manmade obstructions (wood, steel piles, debris), fine-grained to dense coarse-grained materials, cobbles and boulders, all below groundwater. A slurry MTBM convertible to varying diameters, equipped with mix shield capabilities, was selected to cope with the conditions. This paper will discuss access shaft construction,

Jan 1, 2005

By Thomas L. Richardson, David R. Chapman, Gary W. Gilbert

The two contracts of the Big Walnut Augmentation/Rickenbacker Interceptor(BWARI) sewer project for the City of Columbus, Ohio total nearly 35,000 feet of 14and 12-foot diameter tunnel. EPB TBMs will install precast concrete segmental lining through difficult glacial soils ranging from clean granular to hard till with high groundwater and boulders, crossing roads, railroads, and a large stream. Construction of 12 shafts and a large Interconnect Structure involving major ground stabilization work is required. The paper will review design of major project elements and present an update on construction progress.

Jan 1, 2005

By G. P. Tomaino

Talc is a layered, hydrous magnesium silicate mineral. It has a soft, soapy feel and typically a smooth texture. Talc is also known for its insulation, heat resistance, chemical stability, oil absorption and strong covering quality. Talc, Mg3Si4O10 (OH)2, has a theoretical chemical composition of MgO at 31.7 percent, SiO2 at 63.5 percent, and H2O at 4.8 percent. However, talc’s chemical and mineralogical composition can vary depending on its geological history/parent rock association. These mineral associations and variable levels are usually chlorite and carbonates (magnesite, calcite and dolomite). Two key elemental substitutions that can occur in the talc crystal structure are iron for magnesium and fluorine for hydroxyl. These compositional differences may limit or enhance the talc’s usage in specific market niches. The United States remains self-sufficient in most grades of talc.

Jan 1, 2005

By Ben V. Petersen

Surveying is to tunneling, as a steering wheel is to a car—somewhat essential if you want to end up in the right place. The principles of tunnel surveying have remained unchanged since the first tunnels were constructed: To mathematically connect the selected start and end points of a tunnel and physically translate that alignment onto the ground. The alternative is just dead-reckoning and leaves the probably less than satisfying end results to chance. Today’s laser-guided tunnels often have to thread the needle through a maze of soil types, utilities, structural features and other underground considerations. Surveying makes it possible.

Jan 1, 2005

By J Krawcz, S Wasilewski, W Mironowicz

Barometric pressure and its variation in deep underground workings have a considerable effect on ventilation conditions. Pressure changes which create transient states of air flow and air parameters in workings are especially significant. Experiments have shown that pressure changes have a remarkable effect on air parameters at mine workings and hence, attempts to evaluate the scale of this phenomenon are of value. Continuous monitoring of the barometric pressure on the surface of mines allows for the detection of changes in pressure which undoubtedly influence alternations of pressure in the underground areas of mines. Very important factors are the internal disturbances of pressure within a mine ventilation system due to variable conditions of fan operation and the operation of a winding machine where a mine cage moving in a shaft causes piston like disturbances. Local transient disturbances caused by temporary opening/closing of air stoppings due to personnel or underground transport traffic are of importance. The results of over two years of observations of barometric pressure and its influence on pressure variation in underground mine workings are presented in this paper. The observations were possible through the installation of pressure sensors at selected points of the downcast shaft in a mine. Of interest are the observations of the transient states of pressure and other air parameters caused by emergency fan stoppage, movement of a mine cage and changes due to the opening of air stoppings. Data acquired during experiments of opening and closing air stoppings were used for the validation of a flow model in a long working.

Jan 1, 2005

By Marilia S. de Magalhaes

Keywords: sinter, characterization, agglomeration, iron ore Iron ore sinters are the main burden of blast furnaces for pig iron production. The evaluation of these agglomerates is very important due to their properties affect indirectly the productivity and costs of production of the steel industry. In the sintering plants, the standard procedure of sinter assessment has been carried out by particle size control, bulk chemical analyses, tumbler and/or shatter tests and determination of reduction degradation and reducibility indexes. Microscopy techniques have just been applied to characterize sinters produced in pilot conditions, however, these techniques, the classical ones and the less traditional, allow enhancing the industrial sintering process assessment. For investigation of the phases, microstructures and fabric, reflected-light and scanning electron microscopy(backscattered electrons images) were used; for micro analytical chemical examination, energy-dispersive X-ray spectrometry; for Kikuchi patterns registers, electron backscattering diffraction. In addition to the microscopy techniques, the magnetic behavior was depicted by means of magnetic susceptibility measurements. Iron ore sinters are made up by hematite, magnetite, silicoferrite of calcium and aluminium and silicates. These phases develop either during sintering or, in some proportion, represent remnants of ores and fluxes; this is the case of some hematite and Mg-bearing silicate, respectively. From the magnetic susceptibility results, three different behaviors were determined, which are directly related to the magnetiteproportion in the samples. The phase association and proportion, the sintering conditions andthe quality assessment are some features appraised by such procedures, which reveal themagnitude of this proposal in sintering plants.

Jan 1, 2005

By Charles Stone, Madan Naik, Drupad Desai, Karel Rossler

Planning of New York’s new subway line dictated the location of shallow underground station caverns and track crossovers. Clear span openings ranging from70 feet to 100 feet and lengths in excess of 1000 feet, coupled with low rock cover ranging from 25 feet to 40 feet required judicious selection of construction methods, equipment, and proper sequencing of the excavation stages. Rock classifications alone could not predict the behavior of the rock mass during construction. A robust design procedure that considered most of the important aspects of rock behavior and elements of shallow tunnel design, minimized the negative impacts of variable geotechnical data. This paper describes the intricacies of the planning and design of the $16 billion Second Avenue Subway with insight into how to overcome the design complexities and construction challenges of the urban underground.

Jan 1, 2005

By W. Z. Rogers

U.S. feldspar output sold or used in 2004 was estimated to be 790 kt (871,000 st), valued at $43 million free-on-board plant. This was below 2003 and about the same volume as 2002. The strong housing market in the United States maintained demand for ceramic tiles, plumbing fixtures, and fiberglass insulation requiring feldspar and shipments of glass containers increased by about 4 percent. Imports of ceramic tiles and plumbing fixtures continue to increase, taking the place of U.S. produced goods, and the feldspar required to make them. Output included flotation concentrates, feldspar content in feldspar-silica mixtures, potash feldspar and aplite.

Jan 1, 2005

By Bradford F. Townsend, Colin R. Speers

INTRODUCTION This is the first in a series of papers addressing practical tunnel lining design. The format for this and future papers is to present a particular topic and support the presentation of the guidelines by the practical application of a case history. The primary intent is to provide guidelines for the geotechnical and structural design of tunnels where the tunnel size and/or ground conditions dictates that systematic support of the excavation is required following each increment of excavation. This method of tunneling is commonly referred to as Sequential Excavation and Support(SES) and is also commonly termed the New Austrian Tunneling Method (NATM) The authors developed the design guidelines from experience gained over the past two decades during the design and construction of several major railway, highway and water-transfer tunnel projects in Africa and Asia. During this time it has been possible to compare the performance of the as-constructed structures to the predicted performance as given by the design process. Excavation was typically carried out in widely varying ground conditions (weak-bedded rock, jointed hard rock, and soil-like poorly cemented rock with groundwater). It is therefore intended that the design guidelines could be applied, in general terms at least, to any tunnel excavated in any ground mass condition with any ground material type (hard rock, soft rock, bedded rock, soft ground, and soil) with or without ground water. This first paper is an introductory paper that defines the scope and a brief outline of the design issues that may be presented in detail in later papers. What is design? It may be thought of as any rational/verifiable/justifiable process whereby a concept is transformed into information that can be used to bring the concept to reality. In the case of a civil structure, design may be defined as that process, which is documented and can be audited, that determines information such as the shape (form) of the structure, the dimensions (size) of the structure, the thickness and strength of structural members that comprise the structure, etc. This information can be used to compute the time, money and resources required for

Jan 1, 2005

By Jan E. Nesset, Antonio DiFeo, James A. Finch, Jose Hernandez-Aguilar, Cesar O. Gomez

"The gas dispersion measurement sensors and methodology developed by the mineral processing group at McGill University have to-date been employed at a number of plants in Canada, Australia, the U.S., South Africa and South America. In some cases the measurements have been directly linked with metallurgical performance while in others the gas dispersion surveys on their own have proved very useful in understanding the behaviour of the flotation cells. In addition to reviewing the current state of the gas dispersion measurement technology, the paper will present a series of case studies from the various plants and will show how this technology brings a remarkable new level of understanding to flotation behaviour. The influence of the bubble size distribution on recovery and grade are emphasized in the paper.INTRODUCTIONBackgroundThe advent of new sensors to characterize gas dispersion parameters in flotation cells is a development that is long overdue. While the chemistry of flotation has been studied since the early 1900’s, it is only now that the significance of bubble size distribution, gas rate and gas holdup can be meaningfully measured in-plant with robust and precise sensors. Early researchers, like T.A. Rickard (1916) recognized the importance of understanding the role of air and bubbles in flotation when he wrote in 1916 “we know that the key to the flotation process is to be found not in the oil, the acid, or the apparatus, but in the bubbles. The man who understands the mystery of a soap bubble has mastered the chief mystery of flotation”. In his 1999 review paper on The Froth Flotation Century D.W. Fuerstenau laments the fact that due to their “inert nature”, bubbles have never received their due attention from researchers who tended to focus on the chemical, physical, surface and colloidal aspects, rather than the physics of the process. It is perhaps fitting that now, 100 years after the inception of industrial flotation practice at Broken Hill, Australia, researchers and industry have turned their attention toward the importance of truly understanding the role of bubbles in flotation."

Jan 1, 2005

By F. Freme

Coal production in the United States increased in2004 by 36 Mt (39.7 million st) to end the year at 1 Gt(1.11 billion st), according to the U.S. Energy Information Administration (EIA). This was a 3.7-percent in-crease from 2003’s 971.6 Mt (1.07 billion st) (Table 1).(All percentage change calculations are done at the short-tons level.) Although U.S. coal consumption rose in 2004, not all coal-consuming sectors had increased consumption for the year. Coal consumption increased in the electric power sectors by 1 percent and declined slightly in the other industrial sector, while coking coal consumption dropped by 2.4 percent. U.S. coal exports rose for the second consecutive year, while coal imports again increased to record levels. Coal stocks declined during the year, as electric generators used their stockpiles to helpmeet increased demands and missed shipments. Coal producers used their stockpiles to supplement their production levels.

Jan 1, 2005

By R. Minango

Solvent extraction of Cu from acidic leach, using an oxime extractant, e.g. LIX 984 or Acorga is a well-known and establishedprocess. As the process advances, Cu is extracted to the solvent and is replaced by H+in the aqueous phase. At high acidity the distribution coefficient of Cu between the solvent and the aqueous phase decreases, and eventually a relatively high concentration of Cu remains in the raffinate, regardless of the number of equilibrium stages. In many processes this phenomenon is immaterial, as the raffinate returns to the leaching and no copper is lost. But when the copper raffinate is used for processing of additional metals, minimal concentration of Cu in the raffinate is essential for an effective process. The recommended process includes three steps: SX-1?standard extraction of Cu with oxime. The resulting raffinate contains about 6?8 g/lCu and 50 g/lH2SO4. SX-N?Extraction of most of the acid into an amine-based solvent, and stripping it with a base, e.g. aqueous ammonia, caustic, Na2CO3etc. The extraction removes no metals, but decreases the concentration of acid from 50 to10 g/l. SX-2?Extraction of the neutralized solution once more with oxime, to remove the residual copper. Such a process enables one to get down to 100?150 ppm Cu in the final raffinate. This process was developed and tested in the R&D facility at Chambishi Metals plc, by a joint team of Chambishi & Bateman, using Cognis LIX 984N and real solutions from the plant. In the laboratory the equilibrium isotherms for SX-1, SX-2 and the neutralization were developed. Computer simulation of the results showed that the optimal configuration is two stages for both extraction and stripping for SX-1. For SX2, 2?3 stages of extraction and two stages of stripping are needed. The stripping stages may be common to both SX-1 and SX-2. The neutralization of SX1 raffinate was tested both by conventional precipitation with lime and by extraction with alamine-based solvent extraction and stripping with a solution of 10% NaOH. For the SX-N only one stage was needed for both the extraction and stripping. The bench scale pilot plant was run for both SX-1 and SX-2. The results were very similar to the simulated ones, and the configuration of 2E2S for SX-1 and 3E2S for SX 2 delivered the required raffinate with less than 150 ppm Cu.

Jan 1, 2005

By M. Ramström

"In 2002, Atlas Copco Rock Drills AB released the new rig control system (RCS) technology for all of its drill rig types. RCS opened the way for a new generation of computerized drill rigs based on modern, standard PC-computer technology. Drilling accuracy, information logging, reduction in manpower in some types, and serviceability have all taken a quantum leap forward when compared with previous generations of drill rigs. RCS is modularized and distributed by means of CAN-bus technology. This technology, which is well proven in automobile applications, forms the communication backbone of the rig. The modularity facilitates almost unlimited possibilities for the expansion and adaptation of drill rig functions."

Jan 1, 2005

By Robert E. McIvor

The Functional Performance Equation for Ball Milling” was first presented in 1988. It now has been used successfully in more than a dozen mineral processing plants. This powerful, yet simple tool provides a new level of understanding of closed circuit grinding. It shows how grinding circuit efficiency is in reality comprised of two distinct efficiencies. It demonstrates how circuit production rate is related, collectively, to these two efficiencies, mill energy input, and the grindability of the ore. It links circuit performance to design and operating variables that can be manipulated, and creates an effective strategy for making plant improvements. This paper covers the derivation and industrial validation of this equation. As part of an engineering and management system that also incorporates suitable metrics and process control, other operators can now use this tool to make improvements and to manage the performance of their grinding operations with clarity and confidence.

Jan 1, 2005

By R. Banda

This paper describes the decision to implement and then the implementation itself, through trials, of electronic ?Smartdets? over previously used shock tubes. It concludes that Mufulira Mine has become the first mine in Zambia to convert 100% of its stoping to ?Smartdets?, because the Mine?s management was prepared to look beyond the unit cost of product and were ready to look at the broader picture of cost effectiveness and increased productivity.

Jan 1, 2005

By A. Mainza

It is common practice in the mineral processing industry to use hydrocyclones for particle classification. However, classification in the UG2 platinum circuits using the hydrocyclone poses major challenges due to the differences in density between silica and chromite, the two major components of this ore. Silica, the PGM carrying component, has an average density of 2.7 and the barren chromite component has an average density of 4.5. When conventional and flat bottom cyclones are used there is a misplacement of particles due to differences in density leading to inefficiencies in the classification by size. As a result of the density effect, coarse silica reports to the overflow, resulting in loss of recovery, and fine chromite reports to the underflow, resulting in loss of milling capacity and unnecessary production of fine chromite. A classifier based on a different concept was required in the classification of UG2 platinum ore. The three-product cyclone, which is a hydrocyclone with two concentric vortex finders to produce three distinct products, has been tested in the UG2 ore application and indications are that misplacement of particles due to differences in the component densities can be minimized through the use of this unit. Industrial and pilot plant trials were conducted and indications are that the three-product cyclone can be installed to selectively produce a middlings stream that can be screened using Pansep screens to provide a screen oversize, which is predominantly coarse silica that can be preferentially reground to recover the PGM values contained in the coarse silica.

Jan 1, 2005

By R. Mckinstry, M. Rantapaa, T. Bolles

"Measurable improvements in throughput have been documented at Barrick Goldstrike due to increased ore fragmentation through efficient drilling and blasting techniques. A decrease in throughput at the autoclave, due to increasingly hard ore, was identified in early 2002. A team of individuals from the open pit and process areas worked closely on the Drill-to-Mill (D2M) Continuous Improvement initiative to ensure that it would address the needs of both groups, with the target of actually improving throughput in future years, despite the projected harder ores. A series of tests were conducted to determine if adjustments to drilling and blasting could positively influence throughput.Better fragmentation and a subsequent increase in mill throughput were achieved through the use of electronic caps for more precision and flexibility, as well as for allowing extremely fast shots; explosives with a higher velocity of detonation (VOD) to provide for improved shock energy; and improved distribution of the explosives by decreasing pattern spacing. Early tests indicated a significant increase in throughput when processing identified harder ore. It is anticipated that the total process throughput (hard and soft ore) will increase by 6 tph in 2003 due to the improved fragmentation of the hard ore.Barrick Goldstrike’s D2M initiative includes roaster hard ore (BWI>17), as well as autoclave hard ore (BWI>15). Approximately 6 million tons of D2M material were shot in 2003, a relatively small amount compared to the 150 million tons to be mined. The benefit of additional ounces produced should far outweigh the additional drilling and blasting costs."

Jan 1, 2005

Effect of Iron on ash fusion temperature and waterwall deposits FeS, H2S on tube material corrosion and erosion [ ]

Jan 1, 2005