Search Documents

By Richard Kastner, Emilie Vanoudheusden, Fabrice Emeriault, Jacques Robert

INTRODUCTION The subway line B of Toulouse (France) has been realized with three different tunnel boring machines (TBM) techniques: Contracts 2 and 5 are excavated with earth-pressure balanced TBM, Contract 4 with a slurry shield TBM, and Contract 3 with a compressed-air TBM. The first three machines are around 7.7 m in diameter, while the last one is 5.3 m. Moreover, a small part of the line (50 m) has been excavated by a conventional method. The tunnels run through the Toulouse molasses, composed of hard sandy clay with pockets and lenses of dense sand. Geotechnical investigations have shown that in these formations, K0 is greater than 1, around 1.8 at a depth of 25 m (Serratrice,2005) and that geotechnical characteristics are homogenous on the whole layout (? =22 kN/m3, Su = 300 kPa, c' = 30 kPa, F' = 32°). The water table is found between 2 and4 m below ground level. As geology, stratigraphy and tunnel cover (between 10 and 20 m) are almost identical, a comparison of movements induced by the excavation by each of the four excavation techniques is possible. This paper presents the soil mass movement measures in the case of the conventional excavation method and in the case of TBM sections. It shows how tunneling parameters may explain the different surface movements observed during excavation. For the sake of simplicity, only the results of Contract 2 (earth pressure balanced TBM)will be presented. MONITORING Monitoring for the Conventional Method Section For the conventional method section (Vanoudheusden et al. 2005) the mass soil movements are measured with two inclinometers and one multi-point extensometer borehole with automatic data acquisition (Figure 1). The monitoring devices include

Jan 1, 2007

By R. Graeme, J. Komadina

Gold Fields acquired an option to purchase the Cerro Corona Project, located in Hualgayoc, Cajamarca Department, Perú, in December 2003. In January 2006, the option was taken up and the transaction closed. During the intervening months, Project development occurred against the backdrop of a Presidential election, increasing national social activism and environmental regulation, rapidly escalating operating and capital costs, as well as unprecedented demand for engineering and technical skills. Project “Lessons Learned” are outlined and discussed in the context of an evolving strategy.

Jan 1, 2007

By F. T. Cawood

This paper focuses on the role of the coal mine surveyor at the start of the 21st century. It demonstrates that surveyors must look beyond their legal appointment and pursue opportunities to add value at an operational or corporate level of the company. It also exposes the shortfall of statutory appointments in defining the surveyor?s role in terms of key business drivers of the company. One such an opportunity is the potential role of the surveyor in mineral accounting and quality assurance to meet mine requirements, market specifications and standards pertaining to corporate governance and reporting. Finally, some thoughts are expressed on what can be done to elevate current practice to best practice and how to achieve this goal

Jan 1, 2007

By Michael Amick

Over the last few years as the coal industry has seen an increase in the price of coal, a renewed interest in the additional mining of pre-law highwall sites has occurred. Much premium coal and property remains behind these pre-law highwalls but access to mining is limited because prior mining used auger machines to remove coal from under the highwall. Older augers seldom reached more than 200 feet and often no more than 100 feet but this zone of auger holes destabilizes the highwall to where additional mining is often unsafe. If the reserve is large enough, the highwall can be stabilized with common flyash and cement grouts to form a face-up for an underground mine but this expensive method is usually not practical for continuous use with a highwall mining machine. It is estimated there are hundreds of miles of highwall riddled with auger holes where the coal reserve available is ill-suited for deep mining for a variety of reasons. However, these same properties are ideal for additional mining with state-of-the-art highwall mining machines that have a reach up to 1200 feet, except to the relatively thin auger mined de-stabilized zone. The renewed interest in highwall mining these properties has driven research into finding an economical way to stabilize the highwall so the highwall mining machine can recover additional coal. This research discovered and fine-tuned a process that is economical and is successfully supporting the highwall at a highwall mining operation. This paper discusses the research involved in determining the strengths need, the methodology used to place any grouts, the effect on mining plans and the increased recoveries. ARMPS-HWM is used extensively in this research. The failure of the highwall, when not grouting, and the success, when grouting using the new materials and equipment utilized, confirmed the ARMPS-HWM method.

Jan 1, 2007

By D. Brosnahan, J. Gathje

Newmont Metallurgical Services (NMS) recently acquired a Scanning Electron Microscope (SEM) with a JKMRC/FEI Mineral Liberation Analyzer (MLA). With the MLA software package, raw particle image and X-ray data can be converted into particle mineral maps and bulk and liberation data can then be calculated for minerals of interest. This type of quantitative mineralogical data can then be used for a wide variety of applications. Ore characterization with MLA can be carried out for existing or processing plants in development. MLA characterization of laboratory test products provides valuable liberation information that assists the research metallurgist in better planning and developing process treatment options for various ore types. This paper describes the use of MLA characterization in a copper flotation test program where the use of various testing options for arsenic depression was being evaluated.

Jan 1, 2007

By understanding the ore breakage characteristics and utilising comminution circuit modelling, the benefits of SAG mill feed size manipulation can be readily assessed. This paper looks at the benefits and problems of total secondary crushing of mill feed and advocates partial secondary crushing as a means of improving grinding efficiency for certain hard ores. Case studies are reviewed for new and existing SAG mill circuits.

Jan 1, 2007

By B. Andresen, S. T. Johansen, H. Tveit, S. Grådahl, B. Ravary

The Norwegian ferroalloy industry has high ambitions regarding environmental standards. Basic research work has been performed to improve the fundamental understanding of ferroalloy processes and the environ-mental aspects. This paper will present work dealing with the understanding of formation and control of NOx, PAH and dioxins. During this work various techniques and methods have been applied, such as comprehensive industrial measurements, laboratory experiments, model development and application of Computational Fluid Dynamics (CFD). The main goal has been to reduce the environmental impact of ferroalloy plants, by means of improving the combustion processes done by introducing new charging routines and optimized furnace operations, instead of installing expensive gas treatment systems. The Norwegian obligations in accordance with the Gothenburg protocol are to reduce the NOx emissions by 30%, compared with the 1990 level within 2010. Measures developed in this work have resulted in 40-60%reduction in NOx emission, and major reductions in PAH and dioxins for ferrosilicon and silicon metal plants. This has been achieved by introducing semi continuous charging and improved furnace operations. Semi continuous charging and optimized furnace operations are shown to reduce the blowing activity (i.e. emission of large quantity of SiO over the charge by direct channelling from the crater zone). It also reduces variation in off-gas temperature and dust production. To understand the processes and to achieve our results we have used online equipment, with fast sample rates and response times, to measure the off-gas compositions and temperatures. Most of the measuring techniques used are based upon optical principles making use of the absorption- and emission spectrum of the gases. In addition a new prototype instrument is developed for continuous measurement of off-gas characteristics, total dust amount and off-gas temperature. The presented work is a result of a long term co-operation research and development teamwork, between the industry and the research community, and has improved both the process and reduced the emissions. The work has introduced new process design and operation standards, and has resulted in ferroalloy production with better environmental standards.

Jan 1, 2007

By J. O. Marsden

Part I in this series of papers considered the chemistry of medium-temperature pressure leaching of copper sulfide concentrates and reviewed the metallurgical testing and initial process development for this technology. This initial work resulted in the development of a process flowsheet utilizing superfine grinding (to a P98 of 12 to 15 µm and P80 of 6 to 7 µm), pressure leaching at 160° to 170ºC, followed by conventional solution extraction (SX) and electrowinning (EW) for the recovery of copper. However, this process required a significant amount of concentrated acid to be fed to the pressure leach vessel to meet the reaction requirements, representing a cost of between $0.03 and 0.05/lb copper (2006 basis) produced by the process. It was immediately recognized that the development of a process that did not require such a large acid addition would be advantageous. This paper, which is Part II in the series, describes the development of a process that incorporates medium-temperature pressure leaching and direct electrowinning (DEW) in a novel and innovative process flowsheet. Phelps Dodge (a subsidiary of Freeport-McMoRan Copper & Gold Inc.) refers to this as the ?MT-DEW-SX? process. Part III in this series covers the large-scale demonstration of the MT-DEW-SX process at Bagdad, Arizona; and Part IV addresses the development and design of a full-scale commercial application at Morenci, Arizona.

Jan 1, 2007

By H. Walqui, G. Rajala, G. Suardini

The Empire mine began operations on 1963. Low grade Magnetite ore is processed to produce iron pellets for blast furnace feed. Three expansions were added to the original plant and several equipment upgrades have been completed to improve the plant performance as the ore characteristics have been changing through the life of the mine. Size reduction is carried out by two grinding stages, the first one using autogenous grinding and the second one using pebble mills. Pebble crushing is also used to break the critical size fraction and increases primary grinding capacity. This paper describes changes in the configuration of the grinding circuits that have helped increase plant throughput and reduce power consumption by more efficiently utilizing assets available. Understanding the different components of the size reduction circuits and plant sections has allowed shifting part of the load from one section of the plant to another without affecting plant throughput.

Jan 1, 2007

By D MacKenzie

The Rise & Shine Shear Zone is a shallow-dipping Cretaceous late metamorphic shear zone formed in a compressional environment. The Shotover mineralised system is dominated by normal faults with well-defined vein systems that cut across Miocene schist folds and faults related to the inception of the Alpine Fault. Despite the geological differences between these mineralisation systems, they share many common features of hydrothermal alteration that have resulted in disseminated gold in altered sheared schist. The most distinctive feature of both systems is the abundant ankeritic carbonate that has formed from decomposition of metamorphic chlorite. Excess iron from this alteration reaction combined with hydrothermal sulphur to form sulphides that host the disseminated gold. The chlorite decomposition reaction was reversed in the latter stages of both mineralisation systems, and this was accompanied by further gold emplacement in the Rise & Shine system.   Both alteration systems involved initial decomposition of metamorphic albite, followed by deposition of albite as a vein mineral in the latter stages. The fluid flow that yielded the disseminated gold was controlled by microshears that pervade host schists, in strong contrast to many Otago Schist vein systems where host rock alteration is absent. The ankeritic alteration in the Shotover and Rise & Shine mineralised systems has increased the volume of mineralised rock, and may have made suitable targets for large-tonnage, low grade gold deposits.

Jan 1, 2007

By Q. Li, B. Ricks

Over the last several decades mineral concentrate long distance slurry pipelines have been installed and successfully operated. Nearly all were installed via the buried construction method. Their record of depend ability and economy has been well proven. However, these systems operate in regions where seasonal soil frost penetration is shallow or non-existent. In recent years interest in long distance mineral concentrate pipelines in northern cold regions has been increasing. For cold regions one must consider seasonal temperatures and soil frost penetration in order to ensure reliable operations through the year. Herein a case study is developed where heat balance and temperatures for small and large diameter long distance slurry pipelines are compared. The study development is as follows: ?Rheological properties are analysed over range of temperatures from near freezing (4ºC; 39ºF) to relatively very warm (40ºC; 104ºF). ?Then assuming similar climatic conditions, soil properties, and pipeline length, a study is carried out for two pipeline diameters, namely: a small diameter (nominal8 inch; 219.1 mm) and a large diameter (22 inch; 558.8 mm). ?The study focus is on maintaining slurry temperature above freezing throughout the pipeline length by illustrating a decision based on burial depth versus coating the pipeline with insulation.

Jan 1, 2007

By Sunil Koppalkar, A. R. Laplante

"A Pilot Plant was installed in one of the grinding circuits of the Dome Mill, Ontario, Canada. Tests were conducted on a KCCD12 Knelson Concentrator to systematically analyze the effect of operating variables on the performance. The main objective of this test work was to explore the effect of very coarse (6 mm) feed size on GRG recovery and performance of the Knelson concentrator. Preliminary results have shown that coarse feed size is deleterious to maximizing recovery. Size-by-size GRG recoveries have shown an unusual trend in the sense that recoveries do not decrease monotonically with decreasing gold particle size. Similar trend observed in one other full-scale unit has been compared. The observed trend is probably linked to the feed size distribution and top size.INTRODUCTIONKnelson Concentrators are the most widely used semi-continues centrifuge gravity separation units for the recovery of gold and platinum group minerals (Xiao and Laplante 2004). The main advantages over the competing centrifugal gravity units are their design, operating simplicity and good separation efficiency that make them the most common choice for gravity circuit. Despite some characterization at bench scale and a limited characterization at full scale, there is a lack of a comprehensive study of impact of operating variables on efficiency that reflects realistic full scale operating practice. GRG characterization studies, at bench scale, on these units provide information about the occurrence of gold in ore samples but fail to provide adequate information about the effect of operating variables for full-scale units. It is well known fact that such work is difficult to undertake on full-scale units owing to the difficulties involved in sampling and systematic variation of operating parameters. To tackle these problems, a pilot facility consisting of a 12-in CD Knelson Concentrator, a feed screen and tailing pump was installed in one of the grinding circuits of Dome Mill. This paper describes the work carried out and the results.Porcupine Joint Venture (PJV)Porcupine Joint Venture was formed in 2002 between Placer Dome Inc. and Kinross Gold Corporation. The JV utilizes the milling capacity of the Dome Mill to process ore from Placer Dome and Kinross mines. The Dome Mill circuit has gravity concentration, cyanidation and CIP circuits to recover gold. Gravity recovery has been used at Dome Mill since inception to recover gold: first by using conventional jigs, which were eventually replaced by two Knelson Concentrators in 1993, one in each of the grinding circuits. Three more Knelsons joined the circuit in 2002 to improve gravity recovery. An Acacia Intensive Leach Reactor was also added in 2002 to process gold concentrates replacing shaking tables (Chong et al 2004)."

Jan 1, 2007

By David Bigby

In the UK, it is becoming increasingly necessary to open new longwall mining areas above old, abandoned workings. In such cases, strategic and gate roadways must often be driven and maintained across highly stressed areas and pre-existing and sometimes only recently formed subsidence troughs. Ground control at the edges of the subsidence trough can be particularly problematic, with complex combinations of stress and rock conditions being encountered depending upon the precise position in relation to underlying pillar edges. For economic recovery of these reserves, it is essential that rockbolt support is used wherever possible. It is therefore very important to the industry to develop its understanding of ground conditions and support requirements in these areas. This paper describes; ? the historical background to these problems and a series of documented UK case studies from the last 20 years. ? the experiences at UK Coal?s Riccall colliery, where a number of longwall panels were worked at a depth of around 800m, some 65m above previously worked longwalls. Actual experience is compared with pre-mining expectations and model predictions. ? design considerations and experience to date at UK Coal?s Welbeck and Thoresby collieries, which are embarking upon a series of longwalls in the Deep Soft seam, 30-40m above previously worked longwalls. The paper outlines numerical modelling techniques used to optimise such mine layouts within the complex geological and geometric constraints of a mature coalfield. These involve combinations of 2D and 3D finite difference and 3D boundary element models. It also discuss new modelling approaches which will be investigated in forthcoming EU funded research.

Jan 1, 2007

By J McNee

Pike River Coal Limited (PRCL) is developing the Pike River Coal Mine in the Paparoa Ranges of New ZealandÆs South Island. The mine is being developed to extract a coking coal deposit of the Brunner Seam, some 46 km northeast of Greymouth, using a combination of continuous miners, road-headers and hydraulic extraction.   The mining area is located within Department of Conservation (DOC) land and is adjacent to the escarpment of the Paparoa Range and the Paparoa National Park. The mine will use its elevation advantage to hydraulically flume coal from the working faces to the pit bottom area where it will be slurried to approximately 35 per cent density of solids and pumped down a slurry line to the coal prep plant some 10.5 km down the Pike River Valley. The coal will be sold on the export market as a high quality coking coal for international steel making.   PRCL faces significant challenges to achieving the goal of cost effective production. The remoteness, high rainfall (greater then 6 metres per year on average), temperature variation and restrictions on access to this subalpine environment have driven the project to develop some distinctive solutions. These include the establishment of survey control in such a difficult environment with vertical and sub-vertical rock faces, significant vegetation and steep slopes by using helicopter survey, aerial photography and LIDAR (Light Detection And Ranging) aerial survey. PRCL has also commenced designing the placement of the main ventilation fans in an underground chamber in the stone drive.

Jan 1, 2007

By I. Jauhari, F. Stober, D. Fowler, B. O. Wasmund, T. Miraza, C. Nichols, A. Taofik Hidyat, K. Said

The existing PT Aneka Tambang (Antam) ferronickel smelter located at Pomalaa, Indonesia consists of two RKEF lines with reduction furnaces nominally rated at 17 MW and 18 MW, respectively. The low power densities and heat fluxes allowed both furnaces to operate with falling water film shell cooling systems. The furnace campaigns comprised a 5-yearly cold shut -down for metal taphole area rebuild and a 10-yearlysidewall and hearth perimeter repair. Towards the end of these campaigns the furnaces would typically be operated at below nominal power due to excessive sidewall temperatures. In January 2001 Hatch performed a smelter study which proposed options which indicated the possibility of a single furnace operation for the smelter, elimination of lime addition and transition to shielded-arc operation with associated efficiency and throughput gains. This paper discusses the process of uprating the second?line furnace capability from 18 MW to 32MW following the decision by Antam to implement the recommendations proposed by Hatch. It will cover the development of scaled-up furnace design basis by Hatch and Antam with the enabling application of Hatch cooling and binding technology. To optimise the capital cost and maximise Indonesian supply content and post installation support, the scope was carefully and clearly divided between Hatch and Antam. The challenges, set backs and valuable learning experiences gained during the implementation of the retrofit include; ?The support and re-use of existing roof system and challenges presented in re-use of existing crucible support steel. ?Training and technical assistance for Antam operators to perform refractory and copper cooler installation and maintenance of crucible integrity technologies. ?Hearth integrity during start-up and development of an initial charge and start-up procedure to achieve planned thermal expansion of the hearth prior to bath formation ?Implementation of a sidewall hold-down system within the refractory sidewall due to space constraints ?Existing furnace foundation reinforcement to overcome lateral forces on furnace piers during crucible support steel expansion ?Conversion of an open-loop gravity feed cooling water system to a closed loop pressurised system with integrated emergency gravity feed and backup system ?Existing water treatment system and pumping system improvement and modification to meet copper cooling system requirements ?Integration of the new instrumentation control system designed by Hatch to increase performance of the furnace monitoring system and operation ?Uprate transformer capacity from 25 MVA to 40 MVA to meet with requirement of Shielded- Arc Furnace Operation.

Jan 1, 2007

By J. Chilton

The fact that methane ignitions continue to occur at the mining face indicates that monitoring with machine-mounted methanometers does not always indicate the presence of high methane concentrations. Methane concentrations at the face change quickly due to changes in airflow. By measuring these changes in airflow, it may be possible to predict changes in face methane levels more quickly. Currently there are no techniques or instruments to accurately measure airflow inby the mouth of the ventilation curtain or tubing. Tests conducted in the NIOSH ventilation test gallery compare the data provided by one-, two-, and three-axis ultrasonic anemometers. The effects of changes in airflow direction and turbulence on instrument readings are discussed, and guidelines are given for selecting the type of instruments to be used for monitoring airflow near the mining face.

Jan 1, 2007

Application of Gy?s formula is appropriate for calculation of the Fundamental Error (FE) prior to samples being collected at any stage of the minerals process, provided that sampling parameters K and a (alpha) have been determined by calibration of the ores. Two types of calibration procedure are well established in the industry, the Hetrogeneity test and the 32-piece sampling tree experiment. The sampling tree experiment uses the variance and average grade of metal analyses from four series of samples at different nominal fragment size, as the basic input data. Pierre Gy suggested the cube as an appropriate exponent of the nominal fragment size for use in his equation. More recent work suggests that this exponent is variable and characteristic of specific ores and therefore requires calibration. The method described here explains the experimental procedure of the calibration. It is then possible to calculate a sampling nomogram using the sampling parameters K and a. This allows the sampler to determine a suitable protocol for the sampling event that will ensure that the FE does not exceed a predetermined precision at any point in the sampling procedure.

Jan 1, 2007

Mine wide, underground wireless communications are possible with the use of Ultra Low Frequency (ULF) technology. Due to the propagation through rock of ULF radio signals a relatively small antenna can provide communications coverage over a complete mining operation. Starting as a Personal Emergency Device (PED) for emergency messaging to miners under all circumstances, the ULF communications system has grown to include capabilities of remote control of underground equipment such as pumps and fans and centralised blasting initiation. This technology is now in use on 5 continents having lately made it onto the African mining scene. The paper and presentation will provide the audience with the benefit from international mining know-how in this technology as well as local African experiences. A recent commissioning exercise for example, is expected to pay for itself in electricity savings within a few months. These and other results from practical demonstrations and usage will be covered. This novel technology becomes an integral part of the daily operating infrastructure of a mine with immediate safety and business benefits. It is able to reduce capital expenditure and is designed for ease of routine operational use. The paper will conclude with insights into current R&D for further development of this technology.

Jan 1, 2007

By Gabriel Esterhuizen

The room-and-pillar mining method is used extensively in underground limestone mines in the Eastern and Midwestern U.S. The rock mass is typically a near-horizontal, bedded deposit at relatively shallow depth. A survey of 34 mines was conducted in which data on roof spans, rock mass properties and support practices were collected as part of a National Institute for Occupational Safety and Health research project into ground control in limestone mines. The average room width is 13.5 m (44 ft), accommodating large mechanized equipment. The results show that the immediate roof beam can consist of many individual layers and can contain several near-vertical joints. In spite of the room widths, the roof is naturally stable in many mines. Observed roof instabilities can generally be related to excessive horizontal stresses or unfavorable geological structures that cause block fallout or beam failure of the bedded roof rocks. The survey showed that the rock mass quality of the limestone does not vary significantly throughout the Eastern and Midwestern U.S. Roof conditions and the need for support were found to be closely related to the thickness and competence of the first layer of limestone in the roof. The findings highlight the need to identify local geological structures and the roof beam characteristics so that support alternatives can be evaluated. Monitoring and observational technologies that are available for identifying potentially unstable roof are presented, which include: roof characterization using the Rock Fall Risk Index, automated logging of roofbolt hole drilling, microseismic monitoring and displacement monitoring.

Jan 1, 2007

By Dan Witkowsky

Beginning on June 11, 2007, as many as 36, kindergarten-to-grade-12 (K-12) teachers will participate in a program designed to educate them all about the mining industry. The 39th Annual A Total Concept of the Mining Industry – All About Mining, will be conducted by the Colorado Mining Association Education Foundation, Inc. (CMAEF) and the Office of Special Programs and Continuing Education (SPACE) at the Colorado School of Mines. This flagship program includes four intensive weeks at the Colorado School of Mines. During that time, more than 75 volunteer lecturers will “educate the educators” about mining and its importance to the United States and the world. During the learning process associated with obtaining a basic understanding of mining and all its aspects, the teachers will be hosted by hundreds of other industry professionals at 10 Colorado mining operations. Also visited will be a government earthquake center, a museum of mining and industry, an earth mechanics laboratory, a metallurgical research center, a metallurgical concentrator, an electric power plant and a steel mill. Questions before, during and after visits will be answered by another select group of volunteers who will travel with the teachers to the various sites.

Jan 1, 2007