Search Documents

By Todd Wanless

This paper addresses the challenges experienced by the designer and three government agencies during implementation of major improvements for the Turkey Creek Tunnel in Kansas City, Kansas. The tunnel serves as a vital stormwater conveyance system for upstream flood control. Major structural deficiencies were identified within the tunnel including complete loss of sidewall and invert. Without immediate attention, complete loss of the tunnel arch could lead to blockage and extensive remedial repairs under difficult conditions. Considering that tunnel flows must be maintained during construction, a phased design and construction process has been implemented to expedite stabilization of the erosion cavities followed by tunnel liner repairs.

Jan 1, 2008

By K. A. Lewandowski

Leach heaps are plagued with problems due to fine material migrating downwards, clogging the spaces between the coarser ore particles, resulting in decreased metal recovery rates. The use of a binder in agglomeration would allow the fine material to be immobilized, increasing the availability for the solution to come in contact with all the ore. As much as 1.64*1012 BTU per year would be able to be saved if a 25% increase in copper recovery was experienced, assuming that 70% of heap leaching units converted to using agglomeration technology. This is equivalent to approximately 18% of the energy currently being used in leaching heaps.

Jan 1, 2008

By Dao Hong Quang

This paper describes the numerical analysis of some geotechnical factors influencing the application of Longwall Top Coal Caving (LTCC) method. The study was aimed at comparing the differences in stress distribution in the chain pillars of the face ends and caving mechanism of the top coal in LTCC method between the flat and inclined thick coal seams. The outcomes from this analysis will benefit mine planners in designing the location of roadway development in the next longwall panel. In addition, results from the study will extend the understanding of caving mechanism in top coal section when applying the LTCC method (with the direction of the longwall face is down dip, retreating along strike) in inclined coal seams. The results demonstrate a clear effect of dipping factor on cavability of the top coal and on the stress distribution in the chain pillar of the face ends.

Jan 1, 2008

By James N. Mure

The paper describes the design development and construction of bored piles at Pindersfield Hospital, Wakefield, U.K. The piles were of monopile type. Monopile is the term used to describe piles which are constructed without pile caps so that the superstructure columns bear directly on the pile top. Pile geotechnical design was developed from the Site Investigation data and testing of two preliminary piles. Final design philosophy is described. Pile structural design was developed from the loadings applied by the superstructure, and the requirements, tolerances and limitations of monopile construction techniques. Construction was closely controlled in order to achieve a ?right first time? result. The conclusion gives a critique of the system and its value.

Jan 1, 2008

Nautilus Minerals and Neptune Minerals are betting that the next great metals rush will take place more than 1,500 m (5,000 ft) below the sea. Nautilus is the first company to commercially explore the ocean floor for gold and copper seafloor massive sulfide (SMS) deposits. Its main focus is the Solwara 1 Project, a polymetallic copper, gold, zinc, silver deposit that is under 1,600 m (5,200 ft) of water off the coast of Papua New Guinea in the western Pacific Oceans? Rim of Fire. Nautilus Minerals, in a joint venture with Placer Dome (now Barrick Gold), began its exploration of what would become the Solwara 1 area in 2005 with side scan sonar and dredge sampling. The dredge and grab sampling confirmed the grade tenor of earlier sampling by scientific research programs. The 45 dredge samples aver-aged 10.8 percent copper, 3.7 percent zinc, 224 g/t (6.5 oz/st) silver and 13.7 g/t (0.4 oz/st) gold. Nautilus has since staked out more than 300,000 km2 (115,800 sq miles) of tenement licenses and exploration applications in the waters off Papua New Guinea, Fiji, New Zealand, Tonga and the Solomon Islands. That is an area about the same size of the United Kingdom. Interest in Nautilus and its projects has grown tremendously since its inception. The company is now listed on the Toronto Stock Exchange. It has raised more than $300 million and spent more than $23 million on exploration. The company has gained the backing of mining majors such as Teck Cominco, Epion, Anglo American and Barrick Gold. It is positioned to become an emerging producer in 2010. Teck Cominco recently agreed to exercise share purchase warrants to acquire three million additional common shares of Nautilus at a price of US$15 million. This will take Teck Cominco?s shareholding to approximately 7.2 percent of the issued shares. Teck Cominco will conduct and manage a ship-based exploration program that will run in addition to the exploration that was already planned for 2008.

Jan 1, 2008

A systematic study of groundwater conditions at eight underground mine sites exhibiting a wide range of groundwater qualities throughout Australia has been completed at the WA School of Mines. This has resulted in a new corrosivity classification for groundwater driven corrosion processes for cement grouted cable strand used in the Australian underground mining industry. The new corrosivity classification is simple to use and corrosion rates may be predicted from readily obtained in situ measurements of groundwater dissolved oxygen.

Jan 1, 2008

By Michael G. Rulff, Tracy M. Holmes

"Vast amounts of time and money are spent fighting flow problems in plants that involve the handling or processing of industrial minerals. Because these types of projects tend to be capitalintensive, the right decisions, made at the design stage, can have a substantial positive effect on the economics of the project.Some of the problems related to solids flow in mineral processing plants include:•,Flow stoppages•,Uncontrolled flow•,Segregation of blended materials•,Build-up and dead material resulting in loss of live capacityUnfortunately few Universities in North America provide courses in the design or selection of bulk solids handling equipment, let alone the theory of bulk solids flow, with the result that engineers do not fully appreciate the effects of bulk solids handling on their process. The usual method of selecting “standard” equipment, all too often, leaves plant operators hammering on hoppers to promote flow, a technique that is not only usually ineffective but also unsafe and often causes damage to equipment. In short, too little consideration is given, at the design stage of projects, to the particular material and operating environment involved and how these will affect handling between process steps.This paper seeks to give a general understanding of bulk solids flow theory including flow patterns and flow property tests, and presents functional design guidelines to ensure reliable flow. As well, a case history will be presented. Our message is clear: To ensure uniform, reliable flow, a plant design must take into account the specific flow characteristics of the bulk solid to be handled or processed."

Jan 1, 2008

By T. Weatherwax

As part of a strategic research initiative at UBC to design and evaluate integrated underground mining and mineral processing systems, work has been done to determine how to utilize the coarse rejects of pre-concentration in the underground environment. An amenability study for nine orebodies from four of Xstrata Nickel?s Ontario operations evaluated both processing and waste disposal methods. The utilization of the rejects as a high quality backfill with minimal binder requirements has been identified as the preferred disposal method. Fill mixes utilizing the rejects in combination with classified tailings, full tailings, and cement were developed based on the geotechnical properties of the rejects. The mix designs were examined for both strength and rheological properties. The paper will present the results of the pre-concentration testwork, the design and strength testing of various mix designs for rejects from the nine ores and presents a conceptual design for an underground pre-concentration system based on this test work.

Jan 1, 2008

By Axel Preusse

On the basis of the Law on Financing Hard Coal Mining dated 28 December 2007, the subsidized German hard coal mining industry will be shut down to the end of the year 2018 in a socially acceptable manner; in 2012 this decision will be reassessed. Even after the abandonment of all mining activities subsequent burdens are inevitable. In this paper, the possible long-term effects resulting from a mining industry history, which is spanning more than 200 years, and their possible consequences are pointed out, in particular in connection with the abandonment of mine water drainage measures which is economically meaningful in the long term. According to the decision situation as it presents itself today, this point in time will be far beyond 2018. In preparation for this, an action framework is to be developed in areas possibly affected.

Jan 1, 2008

By M. J. Leeuwner

Computational fluid dynamic (CFD) modelling is used to research the complex flow structures that exist in a hydrocyclone. By simulation of a two phase (water and air) flow system, the internal flow and multiphase interactions are investigated. The suitability of CFD modelling as a design tool is further evaluated by examining the effect of varying device dimensions. Three hydrocyclone geometries, used in previous studies, are specified. A transient simulation approach, which employs the Reynolds Stress Model as turbulence model and the Volume of Fluid model as multiphase model, is followed. Results are validated qualitatively against experimental measurements from the previous studies. Keywords: CFD modelling, hydrocyclone, Reynolds stress model, multiphase flow

Jan 1, 2008

Currently an Australian Standard for tunnel fire safety is being developed for road and rail tunnels. Other local guidance relating to tunnel fire safety that has recently become available includes publications by both the Roads and Traffic Authority and RailCorp of New South Wales. Internationally, the World Road Congress has completed its 2004 - 2007 cycle, which has resulted in a number of publications. International developments in rail guidance include a new European Standard regarding fire safety in railway tunnels that will come into effect in July 2008. In addition, the National Fire Protection Association committee NFPA 130 are in the process of revising their standard for fixed guideway transit and passenger rail systems, which is due for publication in late 2009. This paper outlines the status of these and other recently published relevant local and international fire safety guidelines and their implications for tunnel projects in Australia.

Jan 1, 2008

By Howard A. Perko

Soldier pile and lagging is a conventional means of temporary excavation shoring. Timber lagging design has traditionally been based upon the designer's experience or empirical rules. One such method is the Goldberg Zoino chart used by the Federal Highway Administration. Most of these methods restrict the designer to a consistent soil profile, certain pile spacing, construction grade timber lagging, and limited depth. The methods do not take into account surcharge loads or a variety of other factors that could arise. A designer working outside of ordinary circumstances with unusual loads, varying soil conditions, or alternate lagging materials has difficulty estimating lateral earth pressures. In rigid earth retention systems, lateral earth pressure is generally assumed to be constant along the length of the wall. In soldier pile and lagging systems, the lagging is often considerably less stiff than the steel soldier piles. As the lagging deflects, the soil tends to bridge between the stiffer elements resulting in a lower pressure on the lagging. Several previously published methods by others for determining this reduced pressure are summarized and discussed. These methods typically consist of using a portion of the active earth pressure in several different pressure distributions. A simple theoretical model is presented for determination of lateral earth pressures on wood lagging. The model is based on a three-dimensional "silo" shaped sliding wedge analysis. Results of the model are compared with other published methods. The model compares well with these methods which cover the normal spectrum of design situations. In addition, the model can be used to estimate lateral earth pressures outside typical situations.

Jan 1, 2008

By K. G. Thorne, L. J. Cabri, L. R. Fyffe, D. R. Lentz, D. Hoy

"Mineralization at the Main zone of the Clarence Stream gold deposit in southwestern New Brunswick occurs within a parallel series of quartz veins that occupy a NE-trending, steeply north-dipping, brittle-ductile shear zone related to the nearby terrane-bounding Sawyer Brook fault. This deformation zone cuts volcaniclastic sedimentary and volcanic rocks of the Silurian Waweig Formation, and is intruded by mantle-derived East Branch Brook gabbroic dikes and a number of felsic dikes. Intermittent shear-zone reactivation during local magmatic activity induced heterogeneous deformation and alteration of the country rocks and dikes. The terminal phase of shearing is associated with narrow pegmatite-aplite dikes that grade laterally into granophyric granite, and into an auriferous quartz vein. Gold, aurostibite, and gold-antimony intergrowths, predominantly with vein quartz, are associated with a low ƒO2 sulfide mineral assemblage (pyrrhotite, arsenopyrite, and berthierite) that has a sulfur isotopic signature consistent with a magmatic source. Gold saturation and deposition occurred episodically between 300° and 360°C at low activity of sulfur, predominantly in response to pressure reduction during brittle failure combined with the effects of decreasing temperature and sulfidation reactions during fluid-wall-rock interaction. Geochronological studies demonstrate that the timing of the emplacement of the pegmatite-aplite dikes and associated auriferous veins overlap with that of the Early Devonian Magaguadavic granite. Moreover, the composition of the dikes is consistent with their derivation from this granite as late fractionates. The Main zone of the Clarence Stream deposit is therefore interpreted to be intrusion-related, with the Magaguadavic granite being the ultimate source of the gold-bearing fluids. La minéralisation de la zone principale du gisement aurifère de Clarence Stream dans le sud-ouest du Nouveau Brunswick occupe une série de veines de quartz parallèles dans une zone de cisaillement fragile-ductile de direction NE et à pendage abrupt vers le nord apparentée à la faille de Sawyer Brook avoisinante qui délimite deux terranes. Cette zone de déformation recoupe les roches volcaniclastiques et volcaniques de la Formation de Waweig d’âge Silurien et est recoupée par les dykes de gabbro d’East Branch Brook, d’origine mantellique, ainsi que par divers dykes felsiques. La réactivation intermittente de la zone de cisaillement durant l’activité magmatique locale a entraîné la déformation et l’altération hétérogènes des dykes et de l’encaissant. La phase finale du cisaillement est associée à de minces dykes d’aplite-pegmatite qui passent latéralement à des granites granophyriques, puis à des veines de quartz aurifères. L’or, l’aurostibite et les intercroissances d’or et d’antimoine principalement associées aux veines de quartz sont associés à un assemblage minéral de sulfures à faible ƒO2 (pyrrhotite, arsénopyrite et berthierite) présentant une signature isotopique du souffre compatible avec une source magmatique. La saturation en or et la précipitation a eu lieu épisodiquement entre 300° et 350°C dans des conditions de faible activité de souffre, principalement en réponse à la baisse de pression durant la rupture fragile ainsi qu’aux effets de la baisse de température et aux réactions de sulfuration durant l’interaction entre le fluide et l’encaissant. Les études géochronologiques indiquent que l’âge de la mise en place des dykes de pegmatite-aplite et des veines aurifères qui leur sont associées coïncide avec le granite de Magaguadavic, d’âge Dévonien Précoce. De plus, la composition des dykes est compatible avec une origine provenant de ce granite sous la forme de phases fractionnées tardives. Le gisement principale (Main zone) de Clarence Stream est ainsi considéré comme étant associé aux intrusions, le granite de Magaguadavic étant la source ultime des fluides aurifères."

Jan 1, 2008

In 2006, a total of 280 metal mining operations reported employment to the Mine Safety and Health Administration (MSHA).1 Metal mines were the smallest mining commodity sector, comprising 1.9% of all mining operations. ? Gold mines comprised 46.8% (n=131) of all metal mining operations. Other common types of metal mines were copper ore (n=34; 12.1%), and iron ore (n=33; 11.8%). ? Nevada had the largest number of metal mines (n=53; 18.9%), followed by Alaska (n=31; 11.1%).

Jan 1, 2008

By Adrian Coombs

The York Durham Sewage System (YDSS) Interceptor Tunnel Project is located in the Town of Richmond Hill, Ontario, Canada, just north of Toronto. Construction commenced in September 2006 and completion is planned for early summer, 2008. The project involved public and agency buy-in of construction technologies and methods that minimized dewatering, design and construction of sealed shafts with jet grout break-in and out blocks in order that Earth Pressure Balance (EPB) mode could be maintained by the Tunnel Boring Machine (TBM) during shaft entry and exit. This paper will discuss the advances that were made possible through the opportunity to apply and test these technologies in order to accommodate the aquifer and artesian conditions present on this project.

Jan 1, 2008

By R C. A Minnitt

This paper illustrates the use of variography and moving average plots as an aid to analysing variations in the process that can be used to direct the improvement efforts. The hydrometallurgical processes used in manganese metal production consist of sequential unit operations that include milling and reduction of manganese ores. Leaching of the reduced ore, is followed by solid-liquid separation, residue disposal, solution purification and electrowinning of manganese metal completes the process. The nearly 250 integrated process control loops rely on reports of pH, flow pressure, level, temperature and chemical analyses. Metallurgical accounting, reconciliation and process control is achieved through monitoring of the chemical and mass balances within the manganese reduction plant, requiring approximately 50 000 analyses of solids, powders and liquids each month. The largest numbers of samples are taken in the cell house. Changes and variations monitored by sample statistics ensure that the manganese products comply with predetermined specification limits. Optimising the information-value of the approximately 50 000 samples in the manganese plant is carried out in tandem with ongoing process optimisation. Variographic analysis of daily sampling data suggests that the cyclical behaviour evident in the moving average plots is only a reflection of random residual variability and not a reflection of true underlying variability related to cyclical phenomena. Low resolution in the variogram of daily sampling data masks the short-range variability that emerges when hourly data are analysed. Hourly samples collected over a 39-day period (giving 941 sample data), helped identify short-range cycles in the process. The relative distribution of variability for daily sample intervals, indicate that 57 per cent arises from V[0], 18 per cent from V[process] and 16 per cent from random residual variation. V[0] includes all the uncontrolled sampling error arising from a poor sampling protocol, the fundamental error (FE), the grouping and segregation errors (GSE), the delimitation error (DE), the extraction error (EE), etc. This confirms the suspicions regarding the suboptimality of the sampling protocol and the way it is implemented. The absence of long-term trends in the leach suggests that short-term variation (less than one day) dominates the process. While the control charts indicate that the overall processes are maintained above the lower specification limits and the target values, there is nevertheless a considerable amount of variability in the system that overhangs the processes and threatens to impact them negatively. Although the variability in the leach is above the prescribed limits, the volatility is a matter of concern because it seems to be uncontrolled. The comparison of the various sources of variability in data collected on an hourly basis suggests that the short-term random variability (V[0]) accounts for almost 50 per cent of the variability in the process. The main source of this variability is due to errors in the sampling protocol and is probably related to the size of the fundamental error (FE), the grouping and segregation errors (GSE), the delimitation error (DE), the extraction error (EE), etc. Remediation of FE and GSE will probably lead to a reduction in V[0], whereas V[process] could be mitigated by reducing the biases associated with DE and EE in particular.

Jan 1, 2008

By Roozbeh Afzali

Designing an appropriate tunnel blasting pattern reduces the cost of rock breakage and subsequent operations such as loading, haulage and support of tunnels. For that reason, we developed a software that designs tunnel blasting patterns. Using this software, three different tunnel blast design models based on parallel hole cut, namely, Swedish, Konya and Energy Balance, were investigated and compared for a virtual tunnel. Accordingly, blasting patterns were designed, for different cross sections. The trend of parameters such as specific charge and specific drilling as functions of tunnel cross-section was determined for each model. Our results show that, in general, The Swedish model gives lower specific charge and specific drilling compared to other models.

Jan 1, 2008

By Vojtech Gall

Pre-support measures for urban tunneling have seen a substantial development in the recent past. Ground improvement techniques, pipe-arch and spiling methods now allow for non-disruptive tunneling at very shallow depths under sensitive structures, rail tracks and roadways. The paper presents experience gained on national and international projects built over the past decade that represent case histories and therefore may be used as guidance for the development of similar solutions for future tunneling projects at shallow depths. Reference projects include tunnels for the Washington, DC Metro, London Underground, Dulles Inter-national Airport, Busway tunnels in Boston and the Ft. Canning Tunnel in Singapore.

Jan 1, 2008

By Tara Bajpayee

Modern, highly productive underground mining operations need to assure the safety of their workforce by understanding where major strata fractures and roof failures could occur. Mines depend on a host of tools to assess ground instability. In-mine microseismic monitoring systems with sufficient number of sensors have also been used to provide this information. These in-mine systems must be robust in design and moved regularly to keep up with the mining advancement. System performance issues depend on maintaining ever increasing cable runs, preventing component damage from mining activities (scaling, blasting, etc.) and avoiding signal degradation due to interference from mining equipment (fans, trucks, electrical equipment, etc.). A potential solution is to use a surface based monitoring system having sensors placed in boreholes above and adjacent to the underground mine workings. These sensors must be capable of detecting and locating strata fracturing associated with rock failure events. A great advantage of a surface based monitoring system is its independence from the underground mine infrastructure. There is less concern with cable maintenance problems, signal degradation by interference from mining activity, or loss of power from the mine?s power grid. The disadvantages include the cost of drilling boreholes and challenges associated with placing sensors in the boreholes, maintaining radio communication and solar power, and public interference (vandalism, etc.). This paper describes a case study where a surface based microseismic system, using triaxial geophones in boreholes drilled from the surface, was deployed at a large limestone mine. The system was operational during a roof fall that occurred in October 2007. It detected the first rock fracture event 17 minutes before the rock fall event. The geophone array was sensitive enough to identify all large rock fracture, impact, and blast events as well as medium size rock fracture events occurring close to the geophone array.

Jan 1, 2008

By Kevan J. R. Ford, Chris A. Fleming, Robert D. Henderson

"Kinross Gold Corporation’s Maricunga mine in Chile presents an ideal opportunity to apply the SART process to a heap leach operation. Given increasing levels of cyanide complexed copper in current pregnant solutions from Maricunga heaps (over 300 ppm Cu), there is a need to reduce these levels and decrease cyanide consumption and cost. Additionally, a means of disposing of this copper is required, preferably as a saleable product. The well published SART process applied to gold-copper cyanide solutions was selected as it allows rapid precipitation of cyanide soluble copper as a relatively pure copper sulphide. The process also allows effective recovery and recycle of cyanide back to the heap leach operation.This paper reviews the SART process chemistry and presents a summary of SART bench-scale and pilot plant testwork completed by Kinross. Key design parameters and engineering aspects of the proposed plant at Maricunga are discussed. SART plant operating costs and net revenue analysis are included and illustrate the compelling economics of installing a SART process plant. INTRODUCTIONMaricunga OperationCompañia Minera Maricunga (CMM), fully owned by Kinross Gold Corporation, operates the Maricunga mine (formerly Refugio) which is located 120 km due east of the city of Copiapó at an elevation of 4,200m above sea level in the Andes mountains of northern Chile. Figure 1 shows a map of the location of the Refugio mine relative to other gold and copper mines in the region."

Jan 1, 2008