Search Documents

By David G. Paton

"Electromagnetic surveys were conducted at the BXL Bulk Explosives Limited Mixing Plant andsurrounding area to characterize runoff from the site and possible impacts of salinity. The BXL Plant is located at the edge of a depressional area and any escape of soluble ions, such as nitrates, would have ended up in the slough to the west of the plant. Two electromagnetic (EM) instruments were used in the survey. A Geonics EM 3 1 was used in October 1997 and in June 1998, a new multifrequency instrument, a GSSI GEM 300 was also tested. Both instruments were individually mounted on a plastic sled with Teflon runners and towed with an ATV quad. Position was determined using a Trimble Pro XL global positioning system (GPS) with a real time correction mode Landstar receiver for an accuracy of about *l m. Both GPS and EM instruments were set to collect data at 1 second intervals. The quadrature maps for both instruments showed essentially the same information, namely of very high conductivity, appearing to emanate from the mixing plant. The levels of conductivity were highest where the saline water appeared to pool, at the southern end of the slough. Soil sampling locations were identified from the EM maps and navigated to using the real time GPS. Composite samples were collected by hand using a Dutch auger, from two locations, in increments of O-1 5, 15-30, 30-60 and 60- 90 cm. The analysis of the soil samples indicated a complete absence of nitrate or ammonium ions; the major anion was sulphate, indicating naturally saline subsoil conditions. The GEM 300 made the collection of data more efficient, as only one pass was required to collect the data from four depth intervals. The EM survey combined with the real time GPS allowed rapid characterization of the site with respect to soil salinity and proved to be cost-effective for Phase l/ Phase 2 site assessments and targeting sampling locations."

Jan 1, 1999

By J. Durkin

The Bureau of Mines has conducted field studies in coal mines throughout the United States to determine the effectiveness of electromagnetic techniques in locating miners trapped underground following a mine accident. Data from these tests have been used to generate models of expected signal and noise distributions as found above these mines. These distributions have aided in placing the expected performance of a through-the-earth electromagnetic communications technique into a probabilistic framework. Results show that at a 10% false-alarm rate, the expected probability o detecting a miner's signal" from a depth of 1000 ft is 54% at 500 ft it is 95%. These depths exceed the actual depths of 90 and 50%, respectively, of United States coal mines. Sensitivity studies have shown that at depth of 1000 ft, the probability of detection will improve approximately 2% for each dB of increase in signal-to-noise (SNR) ratio.

By F. C. Robles Hernandez

This paper presents the results of the electromagnetic semi-solid treatment of the 319 aluminum foundry alloy, Various levels of structure modification were achieved controlling the AC current used to create the Electromagnetic Field, thus manipulating the intensity of the field, The level of grain refinement, partial modification of the Al-Si eutectic, as well as cellular dendrites were observed, A quantitative analysis of the structure was performed using Image Analysis (IA) techniques. In addition a novel Thermal Analysis methodology was developed for the on-line determination of the microstructure modification level.

Jan 1, 2004

By Margarete Kalin

Mine abandonment is associated with the securing of access to underground workings, shafts, raises and adits. Waste rock piles and tailings are generally contoured and revegetated. When the waste materials contain pyritic material seepages can often emerge long after the physical reclamation work has been carried out. Their extent and origin has to be delineated to facilitate remedial measures. The depth to which the seepages extended can be determined with an electromagnetic (EM) survey. This paper reports on the experience gained using a winter and a summer EM survey correlated with measurements of specific conductivity at the sediment water interface. Lake sediments and ponds which represent a homogenous background material are good media, where specific conductivity and electromagnetic conductivity can be correlated. The origin of the seepage within the recontoured mine site requires detailed site knowledge, as many anomalies in heterogenous materials such as represented by a mine site are evident.

Jan 1, 1994

By K. Leung, J. E. Udd, L. B. Geller, F. Kitzinger

"Sixteen miners died tragically at the Paymaster gold mine in Timmins, Ontario, in February 1945 when a badly corroded hoist rope broke. The investigation of the Royal Commission that followed arrived at a number of recommendations (The Legislative Assembly of Ontario, 1947) aimed at avoiding future disasters of this kind. One consequence was the development and legislated use in Canada, several decades ago, of powerful electromagnetic (EM) instruments for the non-destructive testing of mine shaft wire ropes. The authors have been involved for many years in the design, production, and testing of EM instruments (Geller and Udd, 1990, 1992; Geller and Kitzinger, 1991; Geller et al., 1992). Since the mid-1990s, particular attention was paid to the design and operational results obtained from the computer controlled portable MagnographTM II wire rope tester (Geller et al., 1995, 1998).In the present paper, the authors summarize further hardware- and software-related developments of this instrument. Further, an account is given of the results obtained from the most recent design known as the Perma- ScanTM testing system. This is also a computerized dual-function system. In it, however, the sensor head is designed primarily, if not solely, for permanent installation and for remotely controlled operation. This represents a basic departure from traditional designs, which were intended for ad hoc temporary installations. The remote-controlled instrument described in this paper has now been in operational use for more than four years."

Jan 1, 2003

By David A. Hill, James R. Wait

This report contains a summary of analytical research on electromagnetic methods of nondestructive testing of cylindrical conductors. The principal objective is to provide theoretical insight to the operation of electromagnetic sensing of the internal properties of wire ropes that are used extensively in mine hoists. An overall review of past work is also included.

By Marcel M. Djivre

Electromagnetic wire rope testing is the only practical non-destructive method to evaluate the current condition of wire ropes in general, and in the mining industry in particular. The method has been successfully used worldwide for decades. In mining it has considerably improved the safety of operations. Yet, problems persist. In particular both the Loss-of-Metallic-Area (LMA) readings, as well as the Local Fault (LF) readings, as obtained by different instrument operators, were found to be unacceptably diverse. Consequently, large sums have been spent internationally, as well as in Canada, comparing a whole range of these instruments in an effort to rate their performance. The published results clearly confirmed operational experience, namely that the LMA and LF readings were, indeed, unacceptably diverse. Excellent pertinent conclusions were also published. In Canada the authors? conclusion was that while the divergence in the LF signal based results could, possibly, be attributed to both hardware and human-error related factors, the LMA signal related quantitative uncertainties were human-error related. Consequently, much attention was paid in Canada to developing novel control methods, namely computerized ones to replace the more error-prone analogue ones. In addition new sensor-heads were developed, both for portable as well as for permanent installation with remote control operations. While these efforts were of considerable benefit, the situation must again be carefully reviewed with very special reference to deep-level mining, now of immediate concern in Canada as well. In this paper the authors supply an overview of the results obtained by three of the four major international projects referred to previously. Relevant conclusions/comments are also restated. Moreover, specific recommendations are put forward as to how current problems might best be remedied.

May 1, 2004

By J. Persson, N. G. Bliss

Electric furnaces used for smelting and those used for scrap melting exhibit different performance profiles in terms of electrical characteristics. However, the underlying principles are the same for either case. The rationalization of these variables is a major concern for furnace operators and designers. This paper presents the results of a two year study of high speed real time data from a number of electric furnaces around the world, covering a very wide range of design philosophy and product manufacture, to provide a better mathematical insight into rationalizing the furnace operation.

Jan 1, 2004

By M. L. Fuller

DURING the last several years many papers have appeared dealing with the structure of highly polished metal surfaces. The awakening of interest in this subject is due to the applicability of the electron diffrac-tion technique to the study of surfaces. The original theory of Beilby1 considered the surface of polished metals as of the nature of a super-cooled liquid or a vitreous, amorphous solid. The electron diffraction effects from polished metals have been interpreted by many to be a direct experimental proof of the correctness of the Beilby theory. This inter-pretation has been strongly opposed by others, so that at the present time the subject is in an uncertain and controversial state. In the present paper new, and hitherto unpublished, electron diffrac-tion effects from polished zinc are described. These observations indicate that the polished surface of zinc is crystalline.

Jan 1, 1938

By Erich U. Petersen

Recognition of mineralogical and chemical zoning patterns associated with mineralization is an integral part of mineral exploration. Even though the origin of zoning may not always be known, zoning patterns as expressed by the systematic distribution of ore and gangue minerals, alteration or elemental assays (soil and rock geochemistry) have received much attention and are extremely useful in guiding exploration efforts toward locating economic mineralization. By contrast, the potential of using zoning information recorded in solid-solution minerals to address practical geological-engineering problems has received less attention. Solid-solution minerals can provide critical information for common problems faced in exploration, mine development and valuation. Mineral zoning information from solid-solution minerals can now be easily obtained because advances in electron microprobe instrumentation have made these instruments a most efficient, accurate, economical and practical tool for analysis of large numbers of samples. Now entire mines and districts can be studied in a timely and cost-effective manner as required by modern mineral exploration and mining practice. This article shows how knowledge of the composition of fahlore minerals can be used in addressing important problems in exploration, development and valuation. Situations are described in which drilling intersected "low grade zones" (Case one: Orcopampa, Peru, precious metal system) and where there was a need to determine the "lateral correlation of multiple ore intercepts" (Case two: Sheep Creek, Montana, sediment-hosted sulfide deposit).

Jan 1, 1992

By P M. Larionov, V I. Zaikovskii

Transmission and scanning electron microscopy together with X-ray spectral microprobe analysis were used to investigate the structure and chemical composition of pathological calcified formations on the bioprostheses of heart valves. Controllable synthesis was carried out under the conditions (T = 37¦C, pH = 7.4) when the ion composition of the main elements (Ca, P, Mg and NaCl) is close to their concentrations in blood plasma. It is proposed on the basis of the obtained results that the formation of the hydroxyapatite of calcific inclusions on bioprostheses occurs as a result of spontaneous precipitation in the blood plasma. One of the factors determining the formation of massive calcified bodies on the bioprostheses of heart valves can be decreased magnesium concentration in blood.

Jan 1, 2008

"Mechanical alloying (MA) synthesizing technology and thennohydrogen processing (THP) were utilized to produce nanocrystalline Ti-MMC's reinforced by TiB intermetallic compound by using TiH2-B powder mixtures. Powders MA'ed up to 8 hours were examined by X-ray diffraction and SEM study. All MA'ed powders afterwards were HIP'ed at 700, 800 and 950EC for 1 hour. Detailed XRD, SEM and TEM study of the samples were carried out to determine the structure and micrography of the Ti-TiB MMC material processed by MA+THP approach followed by HIP'ing at high temperatures.IntroductionThe fiber reinforced titanium base composites [1,2] which possess a great resistance to high temperature have been investigated. In these studies fibers of C and SiC were used as reinforcing materials. However, these fibers react with Ti-matrix at elevated temperature resulting in product formation at the interface between the matrix and the fiber. Because of the chemical reactions, strength of the product MMC material diminishes.In conventional techniques of whisker reinforced composite material production, the mixtures of matrix metal powders and dispersed fibers are consolidated by hot pressing, HIP and/or hot extrusion. These techniques, however, have some shortcomings. Hard and brittle fibers could be broken during mixing cycle of the processing. Consolidation techniques could also be the cause for fiber breakdown. Attaining of the uniform dispersion of fibers into the metal matrix is not an easy process. The chemical reactions at elevated temperature exposures in the interface between the matrix material and fiber reinforcement cause product formations leading to poor mechanical properties."

Jan 1, 1998

By John M. Cigan

Samples of copper-lead concentrates from the mine of Cia Minerals Santander, Inc., a Peruvian subsidiary of the St. Joseph Lead Co. were recently subjected to special analysis. This concentrate was known to contain bismuth which, under some circumstances, might have incurred a smelter penalty. In this case, customers for the concentrate accepted it and requested a higher concentration of bismuth. Although chemical analysis would disclose the presence of the metal, it was not possible with equipment available at the mill in Peru to determine the mode of occurrence in the fine grained ores.

Jan 11, 1964

By Danforth R. Hale

Minerals for electronic and optical uses divide easily into two sections: (1) quartz and (2) minerals other than quartz. Quartz Quartz, having a great usefulness discovered by the radio communication enthusiasts about 1918, has become a subject of amazingly expanded interest in the U.S. over the past decade as a man-made mineral and a $3 million crystal-growing business. An economic summary of the commercial growing of quartz crystals has a place in a handbook directed to the mineral engineering industry when it is remembered that quartz crystals have long been an important commercial mineral, and that the raw material for “cultured quartz”- that is to say, quartz crystals grown through the ingenuity of man-is still natural quartz. Nearly all the natural crystals come from Brazil. The larger pieces which meet rigorous standards of quality are used for electronic and, to a lesser extent, optical components. Smaller pieces and fragments are used for vitreous silica. The need for high quality material in quantity led to U.S. government-sponsored research programs in the 1940s that have resulted in the factory growing of beautiful crystals of prescribed shape, size, and quality. The development of the cultured quartz crystal is typical of man's success in adapting the product of the mine to increasingly sophisticated uses. A remarkable achievement perhaps, but foreshadowed by experiments in 1908 by Giorgio Spezia (1908), an Italian geologist studying the relative effects of temperature and alkaline environment on the solubility of quartz. Modern radio equipment is most often controlled as to frequency by the presence in the circuit of a separately added "crystal"-the 1918 discovery responsible for the existence and growth of the quartz industry. The "crystal" is quartz, but this component is a carefully oriented and prepared slice from a crystal, but not a crystal as recognized by a rock hound or seen in a museum. How quartz operates to control frequencies is not a proper subject for a handbook on industrial minerals, and references should be consulted (Cady, 1964; Mason, 1964). Quartz belongs to that class of materials called dielectrics: those that do not conduct an electric current but permit electric fields to exist and act across them. Quartz shows the "piezo-electric effect," which means that when a quartz plate is mechanically deformed against its natural stiffness, one of its surfaces becomes negatively charged, the other, positively charged. When the plate is released from the stress quickly, the charges disappear as the plate regains its original shape, but because of mechanical momentum the plate deforms in the opposite direction (to a lesser amount) and the surfaces correspondingly become charged in the opposite direction. By coating the two surfaces thinly with metal and attaching flexible wires, these charges may be brought into an electronic circuit. If the surfaces are suddenly electrically charged by movement of current through the wires, the "converse piezoelectric effect" occurs -the plate deforms. Carry the thought further and it is realized that an alternating current flowing through the wires responds to the mechanical oscillation of the plate and is keyed to this oscillation. By controlling the thickness of the plate its mechanical vibration frequency can bevaried through a wide range. One type of quartz plate, called the AT-cut, having a precisely defined orientation with respect to the crystallographic axes of the crystal, vibrates on a microscopic scale much as a book would deform when placed flat on a table and the top cover moved parallel back and forth with the hand. There are at least 17 other orientations which have been studied, some of

Jan 1, 1975

By Stephen G. Hardcastle, Michel G. Grenier, Kevin C. Butler

Today there are numerous electronic rotating vane and thermal (hot-wire) anemometers, as well as vortex meters available to measure air velocity. Of these, a laboratory and field evaluation has found that certain instruments are better suited to routine airflow measurements in mine roadways and ventilation ducts. This paper concludes a study sponsored by the Atomic Energy Control Board of Canada, that was introduced at the 5th U.S. Symposium. The study investigated the suitability of currently available electronic anemometers as replacements for the traditional mechanical analog devices while maintaining standard methods such as the continuous traverse. Six electronic instruments were subjected to extensive tests under controlled conditions both in a wind-tunnel and in the field at an underground mine. The evaluation concluded that ergonomics and design were major considerations in unit preference as most of the instruments had very similar performance characteristics. Specific findings were: a) In the wind-tunnel the vane anemometers, especially the "micro" vanes, were more susceptible to misalignment or yaw effects but these were not noticeable in the field; b) Both the vortex and hot-wire anemometers were suitable for continuous traverses of mine roadways; c) Traversing ventilation ducts was more practical than a Pitot-tube multi-point assessments or discharge measurements; d) Yaw is a major concern in duct measurements; e) The continuous traversing method for roadways overestimates the average air velocity; f) Hot-wire anemometers can require significant air density corrections; and g) Hot-wire anemometers are better suited than rotating vanes to mine roadways of less than 1 m/s average air velocity. Based on research detailed in this paper, the ventilation engineer should be able to match the mine's requirements with the presented instrument performance characteristics, thereby optimizing the purchase of a new anemometer and the efficiency with which air velocities are measured.

Jan 1, 1993

By John Watson

New Technologies, New Challenges and New Opportunities For quite some time now, numerous explosive manufacturers have spent untold man-hours and millions of dollars trying to develop a blast initiation technology that would “once and for all” provide users with what was once believed to be only a theoretical possibility...nominal timing. Zero “cap scatter” (the amount of variation of delay timing from the targeted nominal) has been the industry’s goal ever since delays were first introduced into the marketplace. Just as adding delay time between blast-holes improved blast performance since their introduction, having the wrong delay or a poorly timed blast has proven to be very inefficient and in many cases hazardous. The question of how precise a blast initiation system needs to be still remains unanswered, but electronic detonator systems being used today indicate that significant improvements can be achieved over conventional pyrotechnic detonators. These systems can typically provide single digit millisecond ranges of variability, if not sub-millisecond in some cases.

Jan 1, 2003

The speed and internal accuracy of today's electronic calculators can be utilized to write an efficient slurry calculation program. The calculator's input/output printing feature offers additional benefits for data organizing and record keeping. This program allows slurry calculations to be performed without the urgency of immediately transferring a calculated result onto a process flowsheet or specification sheet. The number of flowsheets required for some hvdrometallurgical processes means the number of process stream blocks or ladder diagram entries can become substantial. Slurry calculations for such projects tend to become repetitious and tedious, and the chances for errors increase both in calculation and data entry onto process documents. Using this program has minimized both types of errors. Checking process flowsheets is particularly expedient with the program because you may "walk" through the flowsheet on a weight basis, i.e., solids rate and solids density, and have the program verify and/or correct the volume entries, gallons, and specific gravities. The program was initially used on a beneficiation project to check some 500 data entry values on ladder diagrams covering seven process flowsheets. Numerous hand calculation errors were determined and corrected, and the time for completely checking and correcting the flowsheet ladder diagrams was substantially reduced.

Jan 4, 1981

By Raphael Banda

1 Initiating Systems ? a definition An initiation system is a combination of explosive devices and component accessories specifically designed to convey a signal and initiate an explosive charge from a safe distance. In the use of explosives, the initiating system performs the functions of transmission and control of the firing signal to each explosive charge. As functional groups, initiating systems may be considered as: Starters Those which provide the initial signal to start the blasting process. Surface systems Products which provide transmission of the starter signal and delay timing (if any) across the surface of the blast outside the blast hole. In-hole systems Products which provide the signal transmission, delay timing (if any) and the initial explosives energy in the blast hole.1 2 Different types of Initiating Systems The initiation systems commonly used in Sub Saharan Africa are: ? Detonating cord and detonating relay systems ? Capped fuse and igniter cord systems ? Shock tube non electric systems ? Electric systems ? Electronic detonators 3 Overview of Electronic Delay Detonator Technology Conventional detonators use pyrotechnic delay elements and the variation of the actual delay periods is at best approximately 1% the nominal delay. The lack of guaranteed precision common to all pyrotechnic systems enhances the likelihood of negative environmental blasting effects.3 For example, take a 500 ms in hole delay. In conventional detonators this means that 95 % of shots fire within 10 ms of the mean. i.e. a window of 20 ms. Taking a fixed interval between shots of 25 ms, with a range of ± 3 ms, a very ragged firing pattern could be expected which in practice would result in non uniform fragmentation.

Jan 1, 2005

By R. Banda

This paper describes the decision to implement and then the implementation itself, through trials, of electronic ?Smartdets? over previously used shock tubes. It concludes that Mufulira Mine has become the first mine in Zambia to convert 100% of its stoping to ?Smartdets?, because the Mine?s management was prepared to look beyond the unit cost of product and were ready to look at the broader picture of cost effectiveness and increased productivity.

Jan 1, 2005

By Steve Brace

Electronic detonators have been commercially available to the mining industry worldwide for over ten years. It is estimated that total cumulative global sales will have reached 25 million units by the time of the Conference in February 2004. This is below 0.2% of all detonator types sold during this period. Perhaps 20 million will have been used underground in South African gold, diamond and platinum mines. These will have been produced by South African companies, in South Africa for South African customers. Here efforts have met with greater success and in 2003 fully 5 million, or 3% of local detonators sold, could be of an electronic type. However, it is estimated that about US$7.00 (R50.00) has been expended on R & D, manufacturing facilities and marketing, for each unit so far sold. Large sums of money continue to be spent. Despite the apparent success in South Africa, is it justified? Electronic initiation systems have not produced significant technical benefits to the end-user underground nor corporate profits to the supplier. Some doubt they ever will (even from the large surface operations where the price per unit is much higher). A conclusion might be that they have failed. In 1998 Smit and Pistorius wrote a paper titled “Implications of the Dominant Design in Electronic Initiation Systems in the South African Mining Industry”. This ISEE paper seeks to summarise and review the conclusions of the earlier work. These were: that a dominant design had not yet emerged; the type of connector and the way in which detonators are connected and programmed would be a strong determinant influencing the development of a “winning” product; technical aspects rarely solely determine which becomes the dominant design (marketing, social and economic factors often have a strong influence); electronic initiation systems were an emerging technology for the underground gold mining industry in South Africa and because it was under severe cost pressure the mines would look to them to raise productivity and hence profits; finally, as a dominant design begins to emerge, one could expect a number of players to exit from the industry.

Jan 1, 2004