Search Documents

By B. W. Gandrud

To say that the treatment and handling of the "fines" is the most difficult phase of coal preparation is probably an understatement of facts. It is the fine sizes from about 1/16-inch to 0 that are mainly responsible for the inescapable sludge and slurry problems at plants using wet methods of preparation. Sludge and slurry are a problem from the standpoints of both cleaning and dewatering. They cannot be cleaned satisfactorily by "gravity" methods, which are used so extensively on coarser Sizes, due to the fact that fine sizes, particularly from 65-mesh to 0, do not follow the same laws of settling as do the coarser sizes. Although fine sizes are cleaned more successfully on wet-wash tables than in jigs, even tables as usually operated in coal-preparation plants fail on sizes below 100-mesh. As to other phases of the, sludge and slurry problem, wet coal preparation plants are almost universally beset with troubles in connection with the recovery and dewatering of the fine sizes from about 14-or 20-mesh to 0. The sizes finer than 100-mesh further complicate the problems in a wet preparation plant by their tendency to stay in suspension and build up a troublesome load of solids in the circulating water. In order to prevent too much trouble from this source, it is, customary at most plants to bleed a fair-sized stream out of the circulating system continuously and replace it by addition of fresh make-up water. The slurry water withdrawn from the circuit is usually run to waste, in which case it carries with it a considerable amount of fine coal, thus increasing the "washer loss." Another evil results from wasted slurry water in that quite often it finds its way into creeks and larger streams, creating stream-pollution problems.

Jan 1, 1948

By Homer J. Ballinger

During the fall of 1943 and spring of 1944, the Bureau of Mines investigated nine secondary limonite iron-ore deposits in the Williamsville district of Wayne, Butler, and Ripley counties, Mo., by rotary-bucket and power-auger drilling test pitting, and trenching. Studies on beneficiating the ores were made at Bureau laboratories. Iron ore has been mined in Missouri since 1825, and iron mining reached its greatest development between 1870 and 1890. During this period, production averaged about 250,000 tons annually.

Jan 1, 1948

By G. L. Oldright

As a rule, the usual zinc retort smelter fired with natural gas made its own burners, of which there might be 300 per block, out of standard pipe fit-tings. The gas was discharged through a feeder pipe at various distances into a cylindrical horizontal "blow hole" through a pillar block and thence into the furnace; the best location of this gas-feeder pipe was at the horizontal central axis of the blow hole; the side entry into the blow hole usually was used. The air entered the same blow hole behind the gas, through a short nipple, in the inner end of which was a constructing orifice in a clay plug; in this ,work cone-shaped funnels of various lengths also were used. Even with the air and gas correctly proportioned to each burner, small differences in their dimensions were found to influence greatly the temperatures reached, their uniformity, and consequently the percentage of zinc extracted. This fourth paper of a series on cooperative work in the zinc retort plants of the Eagle-Picher Mining & Smelting Company discloses the methods and principles followed in approximating closely the optimum dimensions for various burners, with examples from experimental and commercial furnaces showing the interrelation of such dimensions with combustion and temperatures in the furnace.

Jan 1, 1948

By William K. Cunningham

The investigation described in this report was begun as part of the Bureau of Mines progress to develop acid processes for the extraction of alumina from low-grade bauxite and. clays. A domestic shortage of high-grade bauxite sui table for treatment by the Bayer process became acute as a result of' World War II; an intensive search for a practical acid process using lower-grade alumina-bearing raw materials was therefore warranted. The laboratory development was described in a preceding Bureau of Mines publication wherein the basic theory for the design and erection of a pilot plant maybe found. A 2-ton-per-day continuous pilot plant was constructed and successfully operated at College Park, Md., which demonstrated conclusively the chemical and mechanical feasibility of a solvent purification process for aluminum sulfate. The estimated production cost of $38.64 indicates that under present market conditions the process would not be economically feasible.

Jan 1, 1948

By S. Benedict Levin

In the spring of 1944, during the emergency In the supply of strategic mica, the Bureau core-drilled six aggregating 913 feet, at the Blister mica Trim. Cheshire County, N.H. These holes indicated a downward extension or the mica shoot which was being mined at that time and developed information essential for economic mining of the deposit.

Jan 1, 1949

By BUREAU OF MINES

In 1948 the United States became a net importer of oil. Coupled with an unprecedented domestic production of 5,900,000 barrels daily, imports approximating 500,000 barrels made available a total supply of 6,400,000 barrels a day. Thus, by a herculean effort, the oil industry was able to meet an extraordinary demand at home and, in addition, to ship abroad almost 460,000 barrels daily of petroleum and products. The country’s oil position now differs greatly from that prevailing at the beginning of World War II. Then, actual oil production averaged about 4 million barrels a day, and productive capacity probably was greater than 5 million barrels a day. As the demand of the military and industrial machine grew with the rising tempo of the drive toward victory, the United States not only met its own needs but produced about two-thirds of the total oil requirements of the Allied Nations, excluding Russia. As a people, we can be deeply grateful that the Nation’s petroleum resources were adequate and sufficiently developed to support such a tremendous effort. Even in those critical hours when immediate needs were the paramount issues, a prudent Congress paused to contemplate the importance of an assured long-term supply of liquid fuels. From these deliberations came the Synthetic Liquid Fuels Act of 1944, which authorized research and development work on new sources of oil – coal, oil shale, and agricultural and forestry products. Since World War II, a civilian demand for 6 million barrels of petroleum products has become the order of the day. By drilling as many as 39,000 new wells a year, the production rate has increased enough to meet domestic requirements by a bare margin. Some imports were necessary, however, to fill both domestic and foreign demands, and these doubtless will increase. Is this policy of exploration within the United States and the development of oil in foreign countries adequate insurance for the fulfillment of our future national needs? This question has two aspects – one purely civilian and economic in character and the other significant from the standpoint of our national defense. There are now approximately 4,000 producing oil fields in this country. At first thought, it would appear that production could decline in a considerable number of these fields without materially affecting the overall daily output. However, 48 percent of the oil comes from only 111 major fields which contain 60 percent of the total proved domestic reserves. It is apparent, then, that the flow from large fields – having proved reserves of 100 million barrels or more each – must be sustained if daily production is to be kept at the present levels. Essentially, this means that new major fields must be discovered about as rapidly, or perhaps more rapidly, than the older ones lose productive capacity. From 1940 through 1947, only eight major fields with estimated reserves of more than 100 million barrels each were discovered and proved – an average of one such field a year. The total estimated reserve of these eight fields was less than 1 year’s supply at the present rate of use. As drilling continues, some existing fields ultimately will prove reserves larger than those now known. Without a pronounced increase in the number of major discoveries, however, the prospects for increasing our present productive level are not encouraging. Any gap that appears between domestic productive capacity and demand could be filled with supplies from proved oil resources abroad. Assuming cheap pipeline and tanker transportation to the United States, freedom from exorbitant taxes and charges...

Jan 1, 1949

By BUREAU OF MINES

In 1948 the United States became a net importer of oil. Coupled with an unpre- cedented domestic production of 5,900,000 barrels daily, imports approximating 500,000 barrels made available a total supply of 6,400,000 barrels a day. Thus, by herculean effort, the oil industry was able to meet an extraordinary demand at home and, in addition, to ship abroad almost 400,00 barrels daily of petroleum and products. The country's oil position now differs greatly from that prevailing at the be- ginning of World War II. Then, actual oil production averaged about 4 million bar- rels a day, and productive capacity probably was greater than 5 million barrels a day. As the demand of the military and industrial machine grew with the rising tempo of the drive toward victory, the United States not only met its own needs but pro- duced about two-thirds of the total oil requirements of the Allied Nations, excluding Russia. As a people, we can be deeply grateful that the Nation's petroleum resources were adequate and sufficiently developed to support such a tremendous effort. Even in those critical hours when immediate needs were the paramount issues, a prudent Congress paused to contemplate the importance of an assured long-term supply of liquid fuels. From these deliberations came the Synthetic Liquid Fuels Act of 1944, which authorized research and development work on new sources of oil coal, oil shale, and agricultural and forestry products. ce World War II, a civilian demand for 6 million barrels of petroleum prod- ucts has become the order of the day every day. By drilling as many as 39,000 new wells a year, the production rate has been increased enough to meet domestic require- ments by a bare margin. Some imports were necessary, however, to fill both domestic and foreign demands, and these doubtless will increase. Is this policy of exploration within the United States and the development of oil in foreign countries adequate insurance for the fulfillment of our future national needs? This question has two aspects one purely civilian and economic in character and the other significant from the standpoint of our national defense. There are now approximately 4,000 producing oil fields in this country. At first thought, it would appear that production could decline in a considerable number of these fields without materially affecting the over-all daily output. However, 48 percent of the oil comes from only 111 major fields which contain 50 percent of the total proved domestic reserves. It is apparent, then, that the flow from large fields - having proved reserves of 100 million barrels or more each must be sustained if daily production is to be kept at the present levels. Essentially, this means that new major fields must be discovered about as rapidly or perhaps more rapidly than the older ones lose productive capacity. From 1940 through 1947, only eight major fields with estimated reserves of more than 100 million barrels each, were discovered and proved - an average of one such field a year. The total estimated reserve of these eight fields was less than 1 year's supply at the present rate of use. As drilling continues, some existing fields ultimately will prove reserves larger than those now known. Without a pronounced increase in the num- ber of major discoveries, however, the prospects for increasing our present productive level are not encouraging. Any gap that appears between domestic productive capacity and demand could be filled with supplies from proved oil resources abroad. Assuming cheap pipe-line and tanker transportation to the United States, freedom from exorbitant taxes and charges

Jan 1, 1949

By BUREAU OF MINES

In 1948 the United States became a net importer of oil. Coupled with an unpre- cedented domestic production of 5,900,000 barrels daily, imports approximating 500,000 barrels made available a total supply of 6,400,000 barrels a day. Thus, by herculean effort, the oil industry was able to meet an extraordinary demand at home and, in addition, to ship abroad almost 400,00 barrels daily of petroleum and products. The country's oil position now differs greatly from that prevailing at the be- ginning of World War II. Then, actual oil production averaged about 4 million bar- rels a day, and productive capacity probably was greater than 5 million barrels a day. As the demand of the military and industrial machine grew with the rising tempo of the drive toward victory, the United States not only met its own needs but pro- duced about two-thirds of the total oil requirements of the Allied Nations, excluding Russia. As a people, we can be deeply grateful that the Nation's petroleum resources were adequate and sufficiently developed to support such a tremendous effort. Even in those critical hours when immediate needs were the paramount issues, a prudent Congress paused to contemplate the importance of an assured long-term supply of liquid fuels. From these deliberations came the Synthetic Liquid Fuels Act of 1944, which authorized research and development work on new sources of oil coal, oil shale, and agricultural and forestry products. ce World War II, a civilian demand for 6 million barrels of petroleum prod- ucts has become the order of the day every day. By drilling as many as 39,000 new wells a year, the production rate has been increased enough to meet domestic require- ments by a bare margin. Some imports were necessary, however, to fill both domestic and foreign demands, and these doubtless will increase. Is this policy of exploration within the United States and the development of oil in foreign countries adequate insurance for the fulfillment of our future national needs? This question has two aspects one purely civilian and economic in character and the other significant from the standpoint of our national defense. There are now approximately 4,000 producing oil fields in this country. At first thought, it would appear that production could decline in a considerable number of these fields without materially affecting the over-all daily output. However, 48 percent of the oil comes from only 111 major fields which contain 50 percent of the total proved domestic reserves. It is apparent, then, that the flow from large fields - having proved reserves of 100 million barrels or more each must be sustained if daily production is to be kept at the present levels. Essentially, this means that new major fields must be discovered about as rapidly or perhaps more rapidly than the older ones lose productive capacity. From 1940 through 1947, only eight major fields with estimated reserves of more than 100 million barrels each, were discovered and proved - an average of one such field a year. The total estimated reserve of these eight fields was less than 1 year's supply at the present rate of use. As drilling continues, some existing fields ultimately will prove reserves larger than those now known. Without a pronounced increase in the num- ber of major discoveries, however, the prospects for increasing our present productive level are not encouraging. Any gap that appears between domestic productive capacity and demand could be filled with supplies from proved oil resources abroad. Assuming cheap pipe-line and tanker transportation to the United States, freedom from exorbitant taxes and charges

Jan 1, 1949

By C. C. Popoff

The development of glass-making industries in the Pacific Northwest as well as other industries that use pure silica has been retarded by lack of local supplies of low-cost raw material. Several quartz deposits along the Skagit River constitute the only known source of relatively pure silica within the range of cheap transportation to the Seattle industrial area. Although some silica has been mined from these deposits, very little information regarding their size, grade, and other physical characteristics has been available to the general public. As a part of its program of investigation of the mineral resources of the Pacific Northwest, the Bureau of Mines assigned the writer to examine the Skagit River silica deposits in October 1946. This report presents the factual data obtained from an examination of the so-called Stoner, Bacon Creek, and Pressentin deposits. These deposits are the largest and most easily accessible known to exist in the area. The deposits are near Marblemount, which is on State Highway 17A. They are within 1 mile to 1-1/2 miles of the Skagit. River Railway, which provides transportation to Seattle, a distance of 130 miles. None of the deposits has been developed thoroughly. The Stoner deposit, however, has been developed by a quarry about, 5,0 feet square and has been exposed by hydraulic removal of the overburden throughout a distance of 180 feet along the hanging wall of the vein

Jan 1, 1949

By H. Kenworthy

This report concerns cooperative milling investigations of the Central mill of the Eagle-Picher Mining &. Smelting Co, The work carried on at the Central mill and the Rolla, Station shows that: It is possible to reduce the Central mill heavy-medium plant tailings by 0.05 to .15 percent zinc; the 3/16-inch to 10-mesh fraction of the jig feed can be treated by sink-float to obtain a tailing containing only half as much zinc as the jig tailing; Humphreys spiral concentration of the flotation tailing does not recover enough zinc to be economically attractive; and crushing and wet grinding of ferrosilicon for heavy medium are commercially feasible. The Eagle-Picher Co. operates extensive mines in the Tri-State area of Missouri, Kansas, and Oklahoma. The ore is milled at its Central hill, which also accepts custom ores. During the recent war the mill handled about 12,-000 tong- of low-grade ore per day. The company milled about 50 percent of the district tonnage and purchased nearly 90 percent of the custom ore. About 50 percent of the mill feed was from company mines. Zinc is the chief value in the Tri-State ores,-with Varying quantities of lead and cadmium minerals, as well as small amounts of germanium and gallium.

Jan 1, 1949

By Soule&apos, John H.

Although known since 1902, the Capitan iron deposits have not been tined, mainly because of the low grade of the ore. Only a small amount of exploratory work has been done since the discovery. C. H. Johnson, district engineer of the Bureau of Mines in New Mexico in 1942-4, visited the property; as a result, preliminary sampling of the property was done in 1943.2/ Owing to the results of this preliminary work, an extensive development program by wagon drilling was planned and executed early in 1944. Equipment available at that time was limited in the depths that could be reached; and as geologic studies indicated the possibility that other limestone beds below the surface might have been replaced by iron minerals, a supplementary development program by churn drilling to reach greater depths was prosecuted in late 1947 and early 1948, with the author as project engineer.

Jan 1, 1949

By John H. Soule

"Although known since 1902, the Capitan iron deposits have not been mined, mainly because of the low grade of the ore. Only a small amount of exploratory work has been done since the discovery. C. H. Johnson, district engineer of the Bureau of Mines in New Mexico in 1942-45, visited the property; as a result, preliminary sampling of the property was done in 1943.3/ Owing to the results of this preliminary work, an extensive development program by wagon drilling was planned and executed early in 1944.4/ Equipment available at that time was limited in the depths that could be reached; and, as geologic studies indicated the possibility that other limestone beds below the surface might have been replaced by iron minerals, a supplementary development program by churn drilling to reach greater depths was prosecuted in late 1947 and early 1948, with the author as project engineer.The following sections note the location and accessibility of the deposits and mention the physical features, climate, labor and living conditions. Property and ownership are outlined, the history and production of the property stated briefly, and the ore deposits are described. The work done by the Bureau of Mines is explained and supported with maps, sections, and assay logs.From March 1, 1944, to June 1, 1944, 179 wagon-drill holes totaling 3,490 feet and 4 test pits totaling 75 feet were completed, and from November 1947 to February 1948 seven churn-drill holes totaling 2,488 feet were drilled and sampled. Metallurgical tests are summarized and referenced.With respect to this report, special acknowledgment is due to J. H. Hedges, chief, Tuscon, Ariz., Branch, Mining Division, and to W. R. Storms, engineer in-charge of the Silver City, N. Mex., field office. Acknowledgment also is due to J. Bruce Clemmer, chief, Tuscon Branch, Metallurgical Division, for analyses done in the last phase of this project, and to Dr. Vincent Kelley of the Federal Geological Survey for his cooperation during this work.The Capitan iron deposits are in secs. 10, 11, 13, 14, and 15, T. 8 S., R. 14 E., central Lincoln County, N. Mex., as shown on figures 1 and 2. The only known large deposit upon which the Bureau did development work lies around the common corner of secs. 10, 11, 14, and 15, as shown in figures 2 and 3, and just southwest of and in the foothills of the Capitan Mountains. This range of mountains trends east and west. The elevation of the highest peak is 10,205 feet.The deposits are reached by traveling on State Highway 48 from Capitan north for 4 miles, to a point just inside the Lincoln National Forest fence and thence due east over a poor dirt road for 1.2 miles. Just over a small wooden bridge, the left-fork is taken, and the poor road is followed to the deposits, a further distance of 1.1 miles (see fig. 1). This road follows the fence to and through the Davis ranch. All the roads from Capitan to the deposits are dirt roads but are impassable only for short periods during and after heavy rain or snow."

Aug 1, 1949

By S. A. Allen

The Eufaula bauxite district of Barbour and Henry Counties in southeast Alabama covers an area approximately 14 miles long, 6 miles wide at the eastern extremity near the Chattahoochee River, and 10 miles wide at the western end near the east fork of the Choctawhatchee River (see figs. 1 and 2). The long axis of this polygon bears a little south of east.

Jan 1, 1949

By Charles E. McCarthy

Part 1 of this report is concerned with the electric-furnace production of calcium aluminate and iron alloy from a variety of siliceous ferruginous ores of aluminum. The furnacing research was directed, first, to determine the extent of the field in the CaO-Al2O3-SiO2 system, in which calcium aluminates with the optimum leaching characteristics are obtained; second, to produce suitable quantities of these aluminate mixtures for pilot-plant leaching tests; third, to investigate the physical chemistry of the reduction reactions during furnacing; and, fourth, to study the economics of the process. The third and fourth steps were not completed. Part 2 comprises another phase of the work and will appear as a second Report of Investigations. It deals with the extraction of metallurgical-grade alumina from the calcium aluminate slag produced in the electric furnace and includes the following steps: leaching, desilicating, precipitating, dewatering, filtering, and washing of the aluminum hydrate. No claim is made that the data are complete, nor has the chronological order of obtaining data been followed. Rather, it is emphasized that additional work is necessary if the full possibilities of the process are to be evaluated. and made available.

Jan 1, 1949

By G. W. Jones

Explosion hazards that may exist when air becomes polluted with combustible gases and vapors are extremely dangerous, particularly if the volume of gaseous atmosphere is large, and an explosion under such circumstances could do tremendous damage to persons and property. The hazard is even greater if explosive mixtures are confined under high pressure, as the pressure could increase to tremendous proportions just before the container would rupture. Because of its interest in safety in the mining and allied industries, the Federal Bureau of Mines has investigated the flammability (explosibility) of various types of combustible atmospheres and published its findings. The explosibility of natural gas has been studied, and the limits of flammability have been determined and published. Other investigations have shown how explosions of natural gas-air mixtures may be prevented by the addition of nitrogen and carbon dioxide.

Jan 1, 1949

By L. L. Hirst

In 1944, the 78th congress of the United States enacted Public Law 290, which directed the Secretary of the Interior, acting through the Bureau of Mines, to furnish industry with basic information and cost data for the development of a synthetic liquid fuels industry. Recently published information with respect to the cost of synthetic liquid fuels processes indicates a wide variation in estimated results. To clarify the results and inconsistencies for the hydrogenation of coal, the Bureau of Mines has prepared preliminary designs and calculated detailed investment costs from which the operating costs to produce 30,000 barrels per day of liquid products, mainly gasoline, by coal hydrogenation were obtained.

Jan 1, 1949

By Lowell B. Moon

Concern over possible wartime shortages finally resulted in passage of the Strategic Materials Act in 1939. As authorized by one section of this legislation, the Bureau of Mines proceeded to investigate deposits of seven strategic minerals with the objective of developing tonnages of low-grade material that could be mined in an emergency. During the war, the size of the program and the number of strategic minerals were increased, and the objective was the more immediate one of aiding production. Since the war, the size of the program has been reduced, but the number of minerals on the strategic list continues to be large. The objective has returned to that of 1939. In the course of the program, more than 10,000 examinations were made and about 1,300 projects were run on deposits of 33 different commodities. A considerable contribution to war production was made in six of the commodities investigated, and a minor contribution was made in twelve others. Substantial reserves have been indicated in 19 minerals. Private interest is currently active in some of the deposits developed in 14 commodities.

Jan 1, 1950

By Graham W. Mark

A chemical method of analysis for beryllium was developed recently in Bureau of Mines laboratories. In this method, quinalizarin (1-2-5-8 tetrahydroxyanthraquinone) in N/4 NaOH is used as a colorimetric titration reagent. This solution has a reddish-purple color, whereas the solution containing equivalent amounts of beryllium and the dye is rather blue. In the titration procedure, standard quinalizarin solution is added to the unknown beryllium sample and to two standard beryllium samples of different but known concentrations. Then adjustments in concentrations of BeO in the two known and of quinalizarin in all three are made until the red-violet shade of the unknown is halfway between that of the two knowns. The amount of BeO in the unknown is calculated from the known BeO content of the solutions between which it lies. It is extremely difficult to distinguish the slight differences in shade of these solutions without the use of a proper light filter, especially when the concentration is over 0.1 mg. of BeO, so a study was made of the transmission characteristics of quinalizarin in N/4 NaOH and of the corresponding beryllium complex to determine what filter would give the most contrast.

Jan 1, 1950

By Bernard Lewis

This report summarizes fundamental research and technical studies conducted by the Explosives and Physical Sciences Division of the Bureau of Mines from July 1, 1949, to June 30, 1950. It is the fourteenth of a series of annual reports whose aim has been to bring to the reader a résumé of the research results that have appeared in published form during each fiscal year under the authorship of members of the staff. These are referred to throughout the report.

Jan 1, 1951

By H. Kenworthy

Small batches of fluorspar flotation concentrates were made into nodules and pellets on a laboratory scale. Several of these were rated acceptable by laboratory evaluation methods. The most satisfactory pellets were produced by mixing fluorspar with about 12.5 percent of water, by weight, and 4 percent of organic binders. These binders) for the most part) originated from petroleum and wood-pulp industries. They were generally difficult to handle and were not easily incorporated with the fluorspars tested. Most of them seemed to have an aversion for damp fluorspar and had to be forcibly mixed with the fluorspar; which was then formed into pellets by pressure. Substitution of fuel oil in varying amounts in the binders enhanced the mixing and penetrating qualities of these binders but at the same tire tended to make the pellets more porous. Tall oils performed the same function to a lesser degree and usually decreased the water absorbency of the finished pellets. Heat-treating temperatures to set up these binders were moderate -about 5000 F. for 30 to 50 minutes was usually enough for both drying and heat treating. Nodules made with 1-1/2 to 2 percent of bentonite as a binder were easily mixed and formed. They required a high degree of heat (about 1,500° F.) to develop their strength and were quite water-absorbent when finished. Two fluorspars were examined for weight and fluorite loss after heat treatment at similar temperatures. Both showed a definite wej.ght and analytical loss of fluorite. Bentonite was used also as a binder to successfully nodulize finely ground oxides of iron, manganese, and nickel.

Jan 1, 1951