Search Documents

By Y Yamaguchi, S Nomura, M Matsumura, C Kamijo

In order to increase productivity and decrease reducing agent rate (RAR) of blast furnaces, slag content of sinter ore must be decreased. However, gangue content in iron ore tends to increase because of resource depletion. Therefore, amount of high-grade concentrate in sinter ore feeds should be increased, but this situation causes a decrease in permeability of the sintering bed so that the productivity of sinter process decreases. In order to increase the amount of concentrate, NSSMS has developed the P-type separate granulation method, RF-MEBIOS and SPEx II technologies. These technologies have been introduced to actual sintering machines. In this report, a new technology using microparticles of iron ore is proposed to increase the amount of concentrate in sinter blends. Basic experiments simulating the sinter making process using microparticles of iron ore were undertaken. Crushed pisolite, containing >60 wt per cent -10 µm was prepared for binder. The pisolite microparticle binder was mixed with another Australian sinter feed ore in a high-speed agitating mixer. They were mixed for about one minute, and then granulated using a pan pelletiser. After that, they were added to another raw material mixed by a drum mixer, and then charged in a pot for a sinter pot test. As a result, when the amount of concentrate increased from 13 wt per cent to 20 wt per cent, productivity was almost kept constant using pisolite microparticle binder.CITATION:Kamijo, C, Yamaguchi, Y, Matsumura, M, Kawaguchi, T and Nomura, S, 2017. Development of an iron ore microparticle binder for increasing the concentrate content of sinter blends, in Proceedings Iron Ore 2017, pp 69–74 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

By Jean Cayouette

"In 1995, Louvicourt Mine started one of the first paste backfill operations in Canada. From 500,000 tonnes in 1995, the annual paste backfill tonnage produced reached 800,000 tonnes in 1999. The maximum throughput of the surface plant (including binders) is 3,50Ot/d with a final density of 75 to 76% solids which gives a slump of 15 to 17cm. Following the start-up of the paste backfill plant, the backfill strength performance levels were well below the pilot plant’s predictions. The introduction of ferrous slag, laboratory tests on various binder ratios with or without additives, and the desliming of the tailings enabled us to optimize the mix and operation costs. Primary and secondary stopes are filled respectively with a paste containing 4.5% and 2% binders consisting of a mixture of 20% cement and 80% ferrous slag. In certain stopes, the binder ratio may vary from 2 to 7%, but always in a ratio of 80/20. Six years after start-up, or 4.5mt of paste backfill later, this paper discusses the present operation and the major changes that have occurred over the years to optimize both the operation and the paste fill quality.INTRODUCTIONLouvicourt Mine is operated by Aur Resources Inc. which owns 30% of the shares. Its partners are Novicourt Inc. (45%, subsidiary of Noranda Inc.) and Teck Corporation (25%). The mine is located in the north-west part of Quebec, about 600 km north of Montreal and about 25 km east of Val d’Or. The mine commenced commercial production in July 1994."

Jan 1, 2002

It is now becoming mandatory in Australia to rehabilitate ponded fine grained coal mine tailings, which may well have been deposited initially with no consideration as to how or whether this could be done nor to the costsinvolved. Of prime importance to the rehabilitation of tailings ponds are the bearing capacity and deformation characteristics of the tailings. Since the tailings are fine grained, time effects will govern the self-weightdeformation of the tailings initially deposited as a slurry and the subsequent deformation of the deposit under the weight imposed by rehabilitation fill. The engineering properties of a particular deposit of ponded tailings havebeen investigated and its response to the placement of fill monitored and analysed.

Jan 1, 1987

By Daniel Hauer

Blocking. (5) The “blocking” of boulders is a much cheaper way of breaking them up than “mud capping.” It should always be used in preference to that method except when too much time will be consumed by a crew of men waiting for the drilling to be done, as shown in example of cost No. 1, as given under “mud capping.” Under such circumstances the time consumed would be a greater cost to the contractor than the extra amount of dynamite. Then, too, on large thin boulders to drill one hole would result only in breaking the stone into such pieces as would again have to be broken; and the many holes might equal the cost of extra dynamite. Under such circumstances if method (6) cannot be used, “mud capping” will have to be resorted to, to do the work economically.

Jan 1, 2006

By Patrik Ericsson

During the 90?s Atlas Copco and LKAB developed a pioneering fully automatic long hole production drilling system based on the Atlas Copco Simba W469 drill rigs. These drill rigs have since then drilled about 8.000.000 drill meters at the LKAB Kiruna and Malmberget mines. In 2005 LKAB ordered three new Atlas Copco Simba W6 C, to complement Simba W469s still in operation. These new Simbas are based on the latest generation computerized drilling technology have proven to meet the expectations of LKAB and now form a base for future automation in Kiruna and Malmberget mines. This paper will present experiences from the introduction of Simba W6 C in LKAB Kiruna and Malmberget mines. The paper will also elaborate on the latest developments in remote access and remote control technology making it a common automation option available for all computerized Atlas Copco drill rigs.

May 1, 2007

By Verya Nasri, Scott Thorburn

The City of Toronto and the Toronto Transit Commission (TTC) have conducted an Individual Environmental Assessment (EA) for a 6.2 km, 4-station underground extension of the Spadina Subway from Downsview Station to Steeles Avenue. This Environmental Assessment Study was performed in three phases including routes and general station locations, alignments and station concepts and detailed assessment of the effects of the undertaking. URS Canada Inc. has led the consultant team for this Study. The anticipated total duration of the project is approximately 6 years and its estimated total cost is about $1.4 billion. This paper presents the planning process of the project, the environmental and engineering challenges, and the measures taken to address them.

Jan 1, 2007

By J. B. Hiskey

Introduction The domestic copper industry has suffered for some time from declining ore grades; rising costs associated with conventional mining, milling, smelting and refining; tightening environmental restrictions; and shrinking markets due to materials substitution. Ore grade depletion is a major problem. It is illustrated by the decline in average copper yield shown in Fig. 1. From 1979, copper grade has dropped 60%, lowering yields from 1.2% to 0.49% (Sousa, 1981). The US copper industry is taking drastic measures to enhance its competitive posture and to guarantee its future worldwide position. In a sense, this involves a general restructuring of the processing philosophy of US copper producers. Judging from recent trends, this restructuring relates to the application of solution mining techniques to the treatment of copper ores and low grade waste material. Recovering copper by leaching techniques has been practiced for centuries. As early as the mid-16th century, some Hungarian copper mines were recycling copper bearing leach solutions through waste heaps (Nash, 1912). In the US, recovering copper from dilute mine waters has been carried out for more than 100 years. There are, however, certain technical innovations that have elevated the importance of solution mining as a process for copper recovery. These include: • Advances in solvent extract-electrowinning (SX-EW); • Developments in acid and acid ferric cure processes for oxide and mixed oxide sulfide ores; • Improvements in heap and dump construction; and • Advances in in situ leaching technology. Generally, solution mining enjoys certain intrinsic advantages over conventional mining and milling. Compared to conventional milling, the combined capital and operating costs of leaching facilities are normally lower, start-up times are faster, and the leaching operation usually has less impact on the environment. Furthermore, solution mining represents an expedient way of extracting metals from small shallow deposits, and is particularly suited to the treatment of low grade sources. And, in the case of waste dump leaching, there is a tremendous resource in-place that has the mining cost already off the books. This paper updates current US copper solution mining trends. Solution mining systems Schlitt (1980) summarized the characteristics of the principle leach systems in the US. He pointed out that the wide variations in copper deposits make solution mining a more site-specific activity than conventional mining and milling. Heap leaching is usually selected for moderate to high grade ores having a copper mineralization that is amenable to acid leaching (oxides, silicates and certain sulfides). Higher grade ores mined specifically for heap leaching are usually treated to optimize copper extraction, therefore, crushing and some pretreatment (acid curing) may be justified. On the other hand, dump leaching practice usually involves leaching low grade waste rock placed on large dumps as dictated by topography and haulage costs. Mine waste is therefore treated in an uncrushed run-of-mine condition. Finally, in situ leaching is appropriate for either very deep ore bodies or for recovering copper from low grade rock left behind in abandoned pit walls, stopes, and subsidence zones from earlier mining activities. True in-situ solution mining should be defined as the leaching of ore in its original geologic setting. Heap leaching Heap leaching has a long history as a hydrometallurgical process for copper recovery. The methodology of heap leaching established at Rio Tinto in Spain more than 300 years ago is basically the same as that used today. Processing concepts, such as solution management (sprinklers and leach/rest cycles) and copper

Jan 11, 1986

By P. Walford, C. Mealin, D. Good

"The geology of the Ore Fault Ni-Cu deposit has been reinterpreted in the light of recent studies of the geology of the Neoarchean Bird River Sill Complex and the occurrence of economic Ni-Cu and Zn-Cu-Ag mineralization. The Ni-Cu sulfides are hosted by the lower of two parallel NNW-trending and moderately W-dipping mafic-ultramafic intrusions related to the Bird River Sill Complex. The bod¬ies intruded a bimodal volcanic suite consisting of weakly deformed mafic flows and felsic pyroclastic rocks. The mafic volcanic rocks are geochemically related to the MORB-type rocks of the Lamprey Falls Formation, and the felsic volcanic rocks are related to arc-type rocks of the Peterson Creek Formation. The original pyroxene- and olivine-dominated mineralogy of the sills has been replaced by variable ser¬pentine-amphibole-talc-carbonate assemblages.The Ni-Cu sulfide assemblage exhibits textures and geochemical signatures typical of orthomagmatic sulfide mineralization. The sulfide minerals are associated with cumulate layers of magnetic ferrochromite that range in thickness from a few to tens of centimeters. A later event of Zn-Cu-Ag sulfide mineralization associated with quartz veining and garnet-chlorite alteration along a fault that strikes north, dips vertically, and cuts all rock types. The mineralized fault is cut by the NE-trending Peterson Creek shear zone. Where the Ni-Cu and Zn-Cu-Ag mineralized zones intersect, remnant magmatic features such as amphibolite or cumulate ferrochromite bands occur within quartz veins or local chlorite alteration. The mixed zones contain a very unusual polymetallic assemblage of Ni, Cu, Zn, Ag, and platinum group elements (PGE)."

Jan 1, 2009

By D. Grabowski, Z. Pokryszka

A study carried out in the iron basin of Lorraine (North-East of France) highlighted the existence of under-oxygenated and noxious gas emissions (carbon dioxide, radon…) in vast built-up areas related to former mine workings. Site investigations showed that the gas flow was mainly due to natural thermal air circulation between old mines and external atmosphere. The main hazards associated with this flow of gas and its potential accumulation in confined volumes in buildings are asphyxiation and intoxication. A further study is in progress in order to better understand the origin of the gas generation within the old iron mine workings. Following the first hypothesis, the carbon dioxide emission is mainly due to the specific hydro-geo-chemical process associating the pyrite oxidation with the acid dissolution of carbonates. KEY-WORDS : gas, emission, iron mine, pyrite.

Jan 1, 2003

By P. J. van der Walt

Some 30 years ago exposure to dense-medium separation in South Africa, culminated in the adaptation of the process for the treatment of -0.5 mm fines. The first commercial plant at Greenside Colliery apparently operated for some 18 years. Three further plants followed, including one treating tin ore. It is gratifying to learn, therefore, that there is renewed interest. The objective of making the process easier to operate (?more practical??) is commendable but the cumbersome technical approach could be counter productive. Perhaps a brief outline of the original thinking might be helpful when analysing the problem.

Jan 1, 2003

By Cesar Sáenz Acosta

El presente texto señala las mediciones de impactos que se han realizado a los programas de responsabilidad social de una empresa minera. Esta medición se realizó a través del cálculo del indicador “Retorno social de la inversión”, aplicando el modelo SROIM o Gestión del Retorno Social de la Inversión. Los proyectos de RS medidos permiten actuar a las empresas de manera responsable con su comunidad y comprenden: salud y nutrición, educación y desarrollo económico. Asimismo, esta medición contribuye a mejorar la comunicación de los impactos generados y desarrolla una gestión adecuada de estos.

Sep 12, 2011

By Jan E. Nesset, Julie Fournier, Jorge Torrealba, Colin Hardie

"Gas dispersion studies have been used to benchmark and optimize plant flotation performance for more than a decade, although this technology is not as widely in use as it likely should be based on the significant improvements that have been reported. Part of the reason may be a general lack of awareness within the industry of just what these improvements have been. This paper reviews a number of the reported case studies, groups them into categories of improvement, and draws some general conclusions. The paper will be of interest to plant engineers and technology providers seeking new approaches and tools for improving their own and clients’ processes.INTRODUCTIONThe sector of flotation hydrodynamics that is now known as gas dispersion technology, and the corresponding terminology, had its beginnings in the 1980’s and early 1990’s in the laboratories of McGill University where the students of Prof. J.A. Finch and Dr. C. Gomez conducted studies of gas holdup, superficial gas rate and water recovery on laboratory flotation columns (Laplante et al., 1983; Xu et al., 1991;, Banisi and Finch, 1994; Finch et al., 1999; Nesset, 2011). Sensors were developed for gas holdup (eg), gas rate (Jg) and bubble size (Db) distribution (Tavera et al., 1996: Finch et al., 1999; Dahlke et al., 2001; Chen at al., 2001; Hernandez-Aguilar et al, 2002, 2005). The sensor measurements were rapidly adapted for use in mechanical flotation machines in plant environments (Gomez and Finch, 2002; Gomez et al., 2003; Cooper et al, 2004; Torrealba-Vargas et al, 2004; Nesset et al., 2007). Somewhat parallel developments were being conducted by Gorain and colleagues at the University of Queensland’s JKMRC on pilot and industrial flotation machines using the McGill approach but utilizing alternate sensor designs for eg, Jg and Db (Gorain et al., 1997, 1999; Schwarz and Alexander, 2006) to link flotation kinetics to bubble surface area flux (Sb). Early industrial applications were those led by the university teams from McGill (Canada), the JKMRC (Australia) and the University of Santa Maria (Chile) at plants in North and South America, Australia, South Africa, Asia and Europe. Industrial organizations that brought the technology on-board in the early 2000’s included Teck Resources (then Teck Cominco), COREM, Vale (then Inco), Anglo American Platinum. Several of the major flotation cell manufacturers also purchased the McGill bubble viewer technology for their own equipment studies. The sensors have continued to evolve with multiple and continuous measurement of Jg (Torrealba-Vargas and Finch, 2006, Bartolacci et al., 2008), gas holdup by acoustic means (O’Keefe, 2007) and a combined Jg-Db device called the Anglo Bubble Sizer (Harbort and Schwarz, 2010). A review of the gas dispersion technology use and development have been provided by Gomez and Finch (2002), Harbort and Schwarz (2010) and Nesset (2010)."

Jan 1, 2015

The GPS and information technology industries are now applying considerable development effort to what is being termed machine control and machine information systems, in particular focusing on the industries the of mining construction and agriculture. GPS based systems are demonstrably finding common acceptance and adding commercial value to many machine applications in industry. This has been the first step in the evolution of the information age that is now reforming mining practices. Adding the technologies of wireless data communication, modem computer databases, and networked PC's mining is on the verge of a new era in overall process management. This paper is a general discussion of what the information age means to miners and a general description of new mining operation technologies available to day from the Caterpillar technology alliance.

Jan 1, 1999

By T. Phiri, Antoine Floribert Mulaba-Bafubiandi

Microwave energy has been recently used in minerals processing to speed up the leaching process or to improve the liberation of targeted minerals (Al-Harahshed and Kingman, (2003); Bradshaw et al., (2001)). Applied to the roasting of sulphide minerals, microwaves allow the ?tunning? of calcine types and products quality in addition to the energy savings as opposed to the conventional roasting (Mulaba, 2006). As more than 85% of world zinc is produced through the ?roast-leach-electrowin? route, an attempt was made to optimize cost, energy and product quality for metal extraction process route. The use of microwaves was the alternative process route selected for the optimisation. Pyrite concentrate (0.17% Zn, 0.09% Cu, 35.71% Fe, 43.76% S) and sphalerite concentrate containing 43.81% Zn, 0.37% Cu, 3.86% Fe and 44.39% S were microwave roasted in a multimode cavity of 2.45 GHz with varying power levels and for different durations. The produced calcines were characterized using AAS, XRF, XRD and Mossbauer spectroscopy while the determination of residual Sulphur was used as products quality control tool to ascertain the degree of roasting achieved on the feed. The leachability of the produced calcines in HCl, HNO3, H2SO4 and HNO3 + HCl has been studied in terms of the best leaching yield, process kinetics economics and environmental aspect. With 800 W power for 30 minutes, ZnO and Fe2O3 were formed corresponding to a 70% sulfur removed from sphalerite and 80% from pyrite concentrates respectively. While the roasting of the above concentrates appeared to be a first degree processes, it was noticed that the microwave assisted roasting of sphalerite and pyrite concentrates yielded lower sample surface temperature for a shorter time (i.e.less than 30 minutes) microwave exposition. Longer time (more than 30 minutes) microwave exposure showed a linear increase in temperature in function of power level used. While optimum roasting conditions were found at 800W, 30 minutes, a 10% increase of sulfur removal was noticed while pyrite concentrate was microwave roasted. Sulfuric acid was seen to give higher leaching yield than nitric acid. Zinc dissolution was hindered by the presence of franklinite.

Jan 1, 2007

By FJ Fourie

This paper describes the concept and development of the use of a uni-delay shock tube system in the timing and initiation of the development rounds, specifically in flat development. It was extended from stoping and now constitutes the only initiation system is use at Kopanang mine. The two explosives initiation systems in general use in underground mines are the conventional fuse-igniter cord system, and the more modern Long Period Delay shock tube system, better known as the numbered LP system. Both are well accepted but have many drawbacks which can result in poor breaking and substantial wastage of the blasting material. Both of these deficiencies cause an increase in the cost of a blast. Hitherto, the limited number of delays available has complicated the use of shock tubes in development blasting. Over eighteen month period to the end of 2007, a project team comprising members from Kopanang Mine and AEL developed a method for the use of a uni-delay shock tubes to time any development round. These uni-delay shock tubes are better known as Reef Masters® or EZ-Stopers® depending on the supplier, and the system has particular application in flat development. During the project, two new shock tube system components were designed, tested and manufactured; namely Splitters and Starter Packs. The system has been successfully tested and implemented in both on-reef and off-reef development ends. At Kopanang, it has now been rolled out across the entire mine. Other AnglogoldAshanti mines are conducting trials and implementations into production sections. Initial results indicate improvements in the ground conditions and excavation profiles. The cost of blasting is showing a downward trend. The authors consider that the system is a tool for use in further blast optimization and will contribute to rationalization of the explosives commodities basket on mines.

Jan 1, 2008

By M. Churchill, V. R. Degner

"Over the past two decades, declining ore body grades, increased operating costs and increased construction costs have provided an incentive for the development of progressively larger flotation machines. As a consequence, the 60 to 100 cubic foot flotation machine of the l950's and l960's is being rapidly replaced by large volume machines, with a resulting improvement in the flotation machine specific capacity (TPH processed per square foot floor space), specific power (HP per TPH processed) and process control simplicity. The recent development, and satisfactory plant evaluation, of the WEMCO 1000 cubic foot flotation machine provides the means by which further economic and operating advantages may be incorporated in high tonnage mill applications.The systematic development of the large 1000 cubic foot flotation machine, and its subsequent performance evaluation in beneficiating metalliferous ores (copper, zinc and iron) will be reviewed in this paper and recently completed plant results will also be provided."

Jan 1, 1982

By M Simpson

Greywackes of the greater Auckland Region (Brynderwyn Hills to Hamilton), when considered on a regional scale, have characteristic ranges of physical, mineralogical and other properties. Some properties (eg density, porosity, crushing resistance, clay index) generally cluster and correlate with the basement greywacke facies, regions and terranes recognised by geologists, and their diagenetic/metamorphic level. Other local factors, particularly variations in mineralogical composition, nature of matrix cement, grain size, and degree of weathering may produce aberrant properties. Some of these local variations, when extreme, have the potential to affect the aggregateÆs performance in roading or the concrete industries.   Smectite and the zeolite laumontite are the major deleterious minerals occurring in fresh greywacke rocks of the Auckland region, although weathered rocks may contain halloysite, an expanding member of the kaolin clay mineral group. These minerals, when found in abnormally high levels in greywackes cause expansion effects in the aggregate. Currently there are inconsistencies in the detailed correlation of shrinkage, clay index, clay mineral content and intrinsic expansion data that need further research to resolve them.  

Jan 1, 2007

By Edward A. Barrett, Roberta A. Calhoun

MORE THAN 30 MILLION EMPLOYEES each year are exposed to hazardous occupational noise, and approximately one-third of them develop permanent hearing loss (NSC, 2000). Possible explanations for the latter statistic include worker regard for noise as a mere nuisance rather than as an occupational safety and health hazard, and consequent neglect of established protective measures (e.g., hearing protection); lack of knowledge concerning noise; improper use of hearing protection; worker indifference; and inadequate training (Bauer & Babich, 2004). Many drill rigs generate high sound levels, which vary according to the type of machine, its location with respect to the physical surroundings, and the location of the sound measured around the rig. A NIOSH study measured noise output from several types of drill rigs during field investigations (Ingram & Matetic, 2003). Two types of data were recorded the actual noise generated by the drill rig at various positions around the rig and the noise to which the drill operator was exposed during the drilling cycle. For the latter, sound level measurements up to 120 dBA were recorded while hammering casing (metal on metal) in drilling a water well (Photo 1). Several types of administrative controls exist to address worker exposure to loud drill rig noise. Rotating duties to decrease exposure time and posting warning signs in high-noise work areas are two such controls. Another is the use of hearing protection. Worker use of hearing protection has been disappointing, however. One study by the University of Michigan found that construction workers used earplugs and earmuffs only between 36% and 61% of the time that they were necessary (Lusk & Kerr, 1998). In a 2001 study, OSHA reported a relatively low rate of 30.4% for use of earplugs among construction workers (Walker, 2001). Why are rates for hearing protection use so low? One explanation may be workers' lack of concern for noise in the workplace. They expect workplace noise to be a loud and in¬ evitable nuisance and, therefore, accept it as part of the job. As a result, they disregard proven measures that can protect their hearing. Other workers may use hearing protection, but do so improperly. They may misguidedly remain in high-noise areas for extended periods thinking they are protected when in fact they are not. Other reasons for low use and/or misuse of hearing protection include poor education, lack of awareness and inadequate training (Nash, 2003). To address the training issue, NIOSH developed two exercises from which drillers can learn about noise, hearing loss and hearing protection. The first is an invisible ink exercise, titled "Drill Rig Incident" (DRI) (Photo 2); the second is a 3-D slide reel training aid, "Wearing Hearing Protection Properly" (WHPP) (Photo 3). DRI is an instructor-

By Manuel Rapiman, Ricardo Sepulveda

The feasibility study of Escondida Norte (ENorte), recommended a slope angle design for the Final Pit. But, according to the experience obtained with the slope adjacent to the West wall of ENorte, in which Compañia Minera Zaldívar (CMZ) gained in its phase 4, a slope of similar geotechnical characteristics will be exposed in the West Wall of Phase 1 (Premine) and of the Final Pit, with an interramp angle 53º and with very good stability results. In this regard, Minera Escondida Ltd. (MEL) performed a study of the slope angles for the phases mentioned and according to this delivered the results of this evaluation, the recommendations and/or the necessary conclusions in the design to ensure that the slopes are stable enough and may enable safe operational management of them.

Jan 1, 2006

This paper examines the issues involved in the technical audit and valuation of exploration prospects. Certain methodologies are more appropriate to use depending upon whether the mineral property valuation is of an exploration area, a project under development, or an operating mine. Valuation approaches that are reviewed include the Multiple of Exploration Expenditure, Joint Venture Terms, Rules of Thumb, and particularly the Kilburn Rating Method. The DCF/NPV Financial Simulation Method, even modified by the use of Expected Values, is not considered appropriate for valuing exploration prospects. The choice of the most appropriate methodology and its successful application depends primarily upon the amount of reliable input data available and, more importantly, the experience and judgement of the valuer. It must be remembered that all valuations are time and circumstance specific and will be generally subject to revision as more data becomes available.

Jan 1, 1993