Search Documents

By Mary Ellen Bruce Large, Antonio Marinucci, Silas C. Nichols

Tip post-grouting of bored pile (drilled shaft) foundations refers to a method where cementitious grout is injected beneath the tip of a shaft to improve the overall performance of the constructed foundation. This technique, when performed satisfactorily and in the appropriate ground conditions, enhances axial load-displacement performance by improving the mobilization of pile’s resistance. Potential benefits associated with tip post-grouting include reduced settlement under loading, better alignment of load transfer curves, and improved ground beneath the base of the bored pile. However, to be able to realize the benefits attributed to this method, the design, construction, of both the bored pile and the post-grouting system must meet a minimum level for quality assurance. The various factors affecting the successful installation and performance of a bored pile (e.g., workmanship, base cleanliness, borehole integrity, and concrete placement) have been discussed by numerous practitioners and researchers in the available technical literature. For a conventional (i.e., ungrouted) bored pile, acceptance is based on a combination of visual inspection, material testing, and the results of integrity and/or performance testing of the constructed pile. A properly executed tip post-grouting program can be a relatively comprehensive and complex process, which is typically evaluated throughout the construction process based on the results of prior projects and/or on test pile(s) at the particular site. For tip post- grouting programs, verification procedures and acceptance criteria should be established during and incorporated into the design process to ensure design intent and objectives are achieved. Project specifications should be produced to ensure performance requirements are achieved. This paper will present and discuss factors affecting the successful execution of tip post-grouting, including grouting criteria, instrumentation, reliability and uncertainty with the method and outcome, and verification and acceptance. INTRODUCTION Constructing bored piles (drilled shafts) is increasingly more challenging given the lack of ideal site locations, tight project site confines, difficult or restricted access, greater demands on drilling equipment, and close proximity to adjacent structures. To evaluate the feasibility of bored piles as an appropriate foundation system, a myriad of factors is evaluated during design, including site conditions and constraints, budgeting and scheduling, reliability and risk exposure, presence of and depth to adequate load bearing soils/rock, and the magnitude of the imposed loading. Moreover, updated design codes increased load demand per element, and improved material strengths have led to more complex foundation designs, larger foundation elements, and significant increases in load magnitude. Monopile (monoshaft) foundations have been utilized where one large bored pile is used in lieu of a group of piles connected via a pile cap. In addition, to accommodate the design criteria, site conditions, and imposed loading, the geometry of the bored piles being designed and installed have been as large as 13 feet (4 m) or greater in diameter and to depths in excess of 260 feet (80 m).

Jan 1, 2018

By Robert S. Dewey

AS a result of drilling operations during 1943, West Texas again added sufficient new oil reserves to replace the oil produced during the year, but failed to maintain its position in currently available reserves because the deeper discoveries will require years for development. Drilling failed to provide the additional oil necessary to meet the increase in current and anticipated market demand. Although 13.3 per cent of the total footage drilled was in wildcat exploration, the ratio of oil discoveries to total wildcats was less in 1943 than in 1942, but comparable to that in 1941. Of the 732 field wells completed, 270 were at Slaughter, 55 at Wasson, 45 at Mascho and 31 at North Cowden. As of Dec. 31, 1943, there were 361 drilling wells including 71 wildcat and 290 field wells; 19.7 per cent were wildcats. It is anticipated that the percentage of wildcats of the total wells will be higher during 1944 than in either 1942 or 1943. Tables 3 and 4 present a three-year comparison of drilling activity and illustrate the downward trend of development that has been in effect during that time. Because of development lag in the deeper Ordovician fields, several years elapse before 2 sufficient number of wells is completed to give a substantial producing rate. As these new oil reserves cost more to find, and will cost more to produce on a barrel basis than the oil marketed during the year, their reserve replacement value to the industry is less in money. Costs While complete costs for deeper drilling are not yet available for analysis, it is evi- dent from the data on drilling rates to comparable depths, contract prices, and general increases in costs, that the cost of drilling has risen approximately 20 per cent during the year. One representative drilling contractor estimates that the average drilling time on a 5000-ft. field well has increased nearly one third and that out-of-pocket costs have increased a dollar per foot. Three major factors contribute to this increased cost: (I) less experienced labor, (2) deterioration in mechanical equipment and expendable material, and (3) increased contract prices. In the past, when there were more drilling rigs than wells to be drilled, some contractors would cut their drilling profit to keep their personnel and rigs working. As this practice is no longer necessary, the contract prices are adjusted upward to assure a profit. On deep and difficult drilling, contracts are let on a cost plus basis. A number of mechanical difficulties have become evident. Inferior quality of steel used in drill pipe and rock bits has added appreciably to drilling time and cost. Contractors are experiencing delay in obtaining repair work and repair parts for prime movers. As the length of drilling time required an shallow-field wells has not increased in proportion to that on deeper wells, it seems that the medium-sized drilling rig is better adapted mechanically than the heavy one to the work imposed. One of the main deficiencies in the heavy rig equipment is inadequate pump capacity. Drilling Mud The increasing amount of deep drilling has emphasized the importance and relationship of good mud to efficient and suc-

Jan 1, 1944

By Robert S. Dewey

AS a result of drilling operations during 1943, West Texas again added sufficient new oil reserves to replace the oil produced during the year, but failed to maintain its position in currently available reserves because the deeper discoveries will require years for development. Drilling failed to provide the additional oil necessary to meet the increase in current and anticipated market demand. Although 13.3 per cent of the total footage drilled was in wildcat exploration, the ratio of oil discoveries to total wildcats was less in 1943 than in 1942, but comparable to that in 1941. Of the 732 field wells completed, 270 were at Slaughter, 55 at Wasson, 45 at Mascho and 31 at North Cowden. As of Dec. 31, 1943, there were 361 drilling wells including 71 wildcat and 290 field wells; 19.7 per cent were wildcats. It is anticipated that the percentage of wildcats of the total wells will be higher during 1944 than in either 1942 or 1943. Tables 3 and 4 present a three-year comparison of drilling activity and illustrate the downward trend of development that has been in effect during that time. Because of development lag in the deeper Ordovician fields, several years elapse before 2 sufficient number of wells is completed to give a substantial producing rate. As these new oil reserves cost more to find, and will cost more to produce on a barrel basis than the oil marketed during the year, their reserve replacement value to the industry is less in money. Costs While complete costs for deeper drilling are not yet available for analysis, it is evi- dent from the data on drilling rates to comparable depths, contract prices, and general increases in costs, that the cost of drilling has risen approximately 20 per cent during the year. One representative drilling contractor estimates that the average drilling time on a 5000-ft. field well has increased nearly one third and that out-of-pocket costs have increased a dollar per foot. Three major factors contribute to this increased cost: (I) less experienced labor, (2) deterioration in mechanical equipment and expendable material, and (3) increased contract prices. In the past, when there were more drilling rigs than wells to be drilled, some contractors would cut their drilling profit to keep their personnel and rigs working. As this practice is no longer necessary, the contract prices are adjusted upward to assure a profit. On deep and difficult drilling, contracts are let on a cost plus basis. A number of mechanical difficulties have become evident. Inferior quality of steel used in drill pipe and rock bits has added appreciably to drilling time and cost. Contractors are experiencing delay in obtaining repair work and repair parts for prime movers. As the length of drilling time required an shallow-field wells has not increased in proportion to that on deeper wells, it seems that the medium-sized drilling rig is better adapted mechanically than the heavy one to the work imposed. One of the main deficiencies in the heavy rig equipment is inadequate pump capacity. Drilling Mud The increasing amount of deep drilling has emphasized the importance and relationship of good mud to efficient and suc-

Jan 1, 1944

Characterisation of Computer Printed Circuit Boards for Hazardous Properties and Beneficiation Studies

Sep 13, 2010

By C. Larsen, I. Orford, L. Strah, M. Renaud, P. Radziszewski

"An AG/SAG mill was commissioned at the Brunswick mine concentrator in October 1998. This paper discusses the original shell top hat liner design for the bi-directional AG/SAG mill, observed liner wear, subsequent liner design modifications, and benefits.The original liners were chrome-moly steel Norsteel with rubber grates and rubber-lined pulp lifters. The design was based on experiences of other AG/SAG mills and recommendations by the liner supplier, Norcast. Liner design modifications were made in an iterative fashion after observing the wear rate profile of the liners; over ten liner sets were implemented. Shell liner design improvements were supported by a design of experiments approach in conjunction with discrete element method (DEM) charge motion simulations. Design optimization took into account lining costs and impacts on operating performance. The team approach to the liner design improvements process is described with emphasis on the application of the design of experiments. The liner wear history and mill operating performance are presented."

Jan 1, 2005

By Joël P. T. Kapusta

Although Peirce-Smith converting remains the workhorse in matte converting, the copper and nickel industries are still confronted with production hindrances such as tuyere blockage, excessive refractory wear and limits in the oxygen enrichment levels of the blast air. The knowledge acquired on high-pressure gas injection technology as well as the invention of the concentric tuyere for steelmaking led to the development of the Air Liquide Shrouded Injector (ALSI) technology for copper and nickel converting. Following a technology demonstration in 1997-98 with four shrouded injectors installed in a Peirce-Smith converter, Falconbridge Limited implemented ALSI Technology on a commercial scale in May 1999 as an integral part of its new Slag Make Converter at Sudbury, Ontario, Canada. The paper presents the various aspects of commissioning ALSI Technology, as well as the operating changes and injector design modifications over the five years the shrouded injectors have been in operation.

Jan 1, 2005

By S. C. Brown

A number of studies have suggested that microscale asperities enhance bubble-particle attachment efficiency; however, in practice the roughening of particulate surfaces can also lead to a decrease in flotation. In the present investigation, it is proposed that nanoscale asperities may be partially responsible for this phenomenon. It is suggested that as inter-asperity separation distances are reduced capillary effects are enhanced leading to the formation of stable liquid domains, which adversely impact bubble-particle adhesion. In addition, obstruction of surfactant self-assembly may occur, further limiting flotation.

Jan 1, 2003

By J. Engelbrecht

South Africa?s re-entry into the fast moving and competitive global economy calls for some careful strategic planning and a good deal of co-operation between suppliers and end-users. The issues that need addressing are generally well known and include: ?South Africa was ranked 45th out of 46 i.r.o. productivity ?SMMEs contribute 1% to exports compared to 40-60% for the ?tigers? ?High unemployment ?Limited skills of the majority of workers ?Slow growth rate of the economy ?The vast majority of suppliers are not world-class ?The vast majority of suppliers are not export or marketing orientated. In order to survive, all parties, i.e. government, labour and business, will have to play their part.

Jan 1, 1999

By Thomas Hans Kleine

In general the software required by a blast designer includes tools that graphically present blast designs (surface & underground), can analyze a design or predict its result, and can assess blasting results. As computers develop and computer literacy continues to rise the development of and use of such tools will spread.

Jan 1, 1995

By Marilia S. de Magalhaes

Keywords: sinter, characterization, agglomeration, iron ore Iron ore sinters are the main burden of blast furnaces for pig iron production. The evaluation of these agglomerates is very important due to their properties affect indirectly the productivity and costs of production of the steel industry. In the sintering plants, the standard procedure of sinter assessment has been carried out by particle size control, bulk chemical analyses, tumbler and/or shatter tests and determination of reduction degradation and reducibility indexes. Microscopy techniques have just been applied to characterize sinters produced in pilot conditions, however, these techniques, the classical ones and the less traditional, allow enhancing the industrial sintering process assessment. For investigation of the phases, microstructures and fabric, reflected-light and scanning electron microscopy(backscattered electrons images) were used; for micro analytical chemical examination, energy-dispersive X-ray spectrometry; for Kikuchi patterns registers, electron backscattering diffraction. In addition to the microscopy techniques, the magnetic behavior was depicted by means of magnetic susceptibility measurements. Iron ore sinters are made up by hematite, magnetite, silicoferrite of calcium and aluminium and silicates. These phases develop either during sintering or, in some proportion, represent remnants of ores and fluxes; this is the case of some hematite and Mg-bearing silicate, respectively. From the magnetic susceptibility results, three different behaviors were determined, which are directly related to the magnetiteproportion in the samples. The phase association and proportion, the sintering conditions andthe quality assessment are some features appraised by such procedures, which reveal themagnitude of this proposal in sintering plants.

Jan 1, 2005

Perhaps one of the most important conferences or symposia which our Institute has conducted, was the joint Aus. LM.M./AJ.M.E. meeting held in Canberra in May 1978, with the theme International Resource Management (Woodcock, 1978).We were privileged to witness active participation in the meeting by outstanding personalities from the mining and metallurgical industries of Australia and New Zealand, the United States of America, Canada and the United Kingdom and to hear addresses on subjects of international significance to the mining and metallurgical industries.Our Institute is one concerned with professionalism.The principal objects of The Institute as described by our founders include, "promoting the arts and sciences connected with the economical production of the useful minerals and metals, and the welfare of those in the industries, by meetings for social intercourse, and the reading and discussion of professional papers, and to circulate by means of publications amongst its members and associates, the information thus obtained".Sir Maurice Mawby (1968) said in his Presidential Address to the Institite, "the most important aspect of these objects was the promotion of the arts and sciences of the mining industry".Why is it then, that a large proportion of the papers given at the meeting in Canberra dealt with world wide social aspects of the mining and metallurgical industries, rather than the technology, the arts and sciences of mining and metallurgy as principal factors in international resource management?The answer is quite simple of course, and that is that the social and political factors are the principal factors which create the demand for basic raw materials and in the long term determine the costs and prices of the commodities which our professional abilities are drawn upon to produce.

Jan 1, 1979

By Tim O’Neil

What prompted the merger of the two long-established American Mining Congress/National Coal Association (AMC/NCA) groups that combine the coal, hard-rock, industrial- and agricultural-minerals sectors of mining? Both associations have been facing similar stresses for several years - structural changes in their respective industries, the changing personality and role of government and well-financed and organized opposition groups. In 1993, the AMC board of directors undertook efforts at reorganizing the association. One board member, who serves on both boards, suggested it might be time to give serious consideration to merging the organizations. This is an idea that had been discussed more or less informally at least three times during my tenure at NCA. Negotiations toward a merger began after that and were consummated in February of this year.

Jan 1, 1995

By King R. L

Low-enthalpy geothermal groundwater resources occur at relatively shallow depths in the Upper Cretaceous/1'ertiary sedimentary sequence in the on-shore Gippsland Basin. The main stratigraphic unit containing hot groundwater is the Latrobe Group. Groundwater temperatures in the range 30 to 70¦C have been recorded from depths between 500 and 1000 m. The hottest groundwater is in the Latrobe Valley and Lake Wellington depressions. Geothermal gradients in these areas range from less than 2¦C/100 m to over 10¦C/100 m (compared to a world average of about 3¦C/100 m). A number of theories have been advanced to explain the geothermal anomalies including exothermic reaction such as oxidation of coal, mixing with deeper, hotter groundwater and high geothermal fluxes along fault zones. Variations in geothermal gradients can also result from type and thickness (and hence thermal conductivities) of the sedimentary pile, depth to consolidated basement rocks, and influence of groundwater flow patterns including proximity to recharge zones. The hot groundwater in the Gippsland Basin has substantial potential as a source of energy for direct heat applications such as process heating, space and water heating for buildings, and agricultural and aquaculture. Geothermal energy has a number of environmental advantages over traditional sources of energy. It is clean, safe, causes minimal land disturbances and in most cases is naturally renewable.

Jan 1, 1992

By A M. Hagni

Certain copper ores from the Nchanga Copper Mine in the northern Zambia Copperbelt are refractory with respect to conventional beneficiation techniques. This paper reviews recent study of those ores to determine their mineralogy, textures and nature of copper occurrence. Two suites of refractory ores were selected for study: 1.  samples of stockpiled ores from an open pit, and 2.  drill core samples from copper ores. Both sample suites are from the upper orebody at Nchanga and contain about 0.3 - 1.4 per cent copper as determined by atomic absorption, but they represent separate stratigraphic, mineralogical and beneficiation problems. Ore microscopic examination showed that fine-grained copper sulfides are totally lacking from both suites of refractory ores. Petrographic study found malachite in the refractory ores from the open pit, but that malachite probably is post-mine. The opaque mineralogy of the open pit refractory ores is dominated by goethite that occurs mostly as pseudomorphic grains after pyritohedral pyrite crystals that average 200 - 250 ¦m across. Haematite occurs as bands within or as outer shells of the goethite grains. Additional goethite occurs locally as finer-grained areas of exotic goethite. The opaque minerals in the drill core refractory ores are dominated by euhedral ilmenite crystals about 50 - 175 ¦m long. Anatase is the dominant opaque mineral in some drill core samples where it is largely pseudomorphic after ilmenite crystals. Goethite accompanies malachite in unusual drill core refractory ores that have experienced intense hydrothermal alteration. Thus, ore microscopy and petrography showed that fine-grained chalcopyrite and bornite and pre-mine malachite were not the causes of the refractory nature of the ores studied. Electron microprobe revealed that most of the copper occurred in solid solution within micas. Application of automated SEM techniques has provided a detailed understanding of the distribution of copper in these refractory ores.

Jan 1, 2008

By D. R. Wilburn

The worldwide budget for nonferrous, nonfuel mineral exploration was expected to increase by 58 percent in 2004 from the 2003 budget, according to Metals Economics Group (MEG) of Halifax, Nova Scotia. The increase comes two years after a five-year period of declining spending for mineral exploration (1998 to2002). Figures suggest a subsequent 27 percent increase in budgeted expenditures from 2002 to 2003. For the second consecutive year, all regional exploration budget estimates were anticipated to increase. The worldwide budget for gold exploration achieved about 50 percent of the total amount budgeted in 2004.This was 68 percent, or US$715 million, higher than the reported 2003 budget. The 2004 worldwide exploration budget estimates for copper increased by 70 percent, orUS$237 million, to US$577 million from the 2003 budget. The budget for nickel exploration increased 52 percent, or US$89 million more than in 2003. The 2004 exploration budget for other mineral targets (primarily cobalt, heavy minerals, industrial minerals and silver) increased114 percent, or US$118 million.

Jan 1, 2005

Keywords: Pyrometallurgy, zinc, electrowinning Zincor has been producing zinc since 1969 via the roast-leach-electrowinning process. It is the only primary zinc producer in South Africa, and currently supplies the entire country with zinc. The plant was built by Goldfields of South Africa, on the site of an old gold and uranium mine. Since then, the ownership of the plant has changed a couple of times, and the plant and process have also been improved. Production output has increased from around 80 000 tons per year to more than 110 000 tons per year. This was done mainly through increasing the capacity of the roasters and acid plant. Zincor produces four main grades of zinc: SHG, Zn1, Zn2, and Zn4, in three shapes: a 25 kg ingot and 1 and 2 ton jumbos. In 2005, a pre-alloy furnace was built that enabled the production of jumbos pre-alloyed with aluminium. This has allowed Zincor's customers to improve the efficiency of their continuous galvanizing lines and to lower their production costs.

Jan 1, 2006

By Siyabonga Malevu

Chemical Initiatives? Umbogintwini plant is the production facility of Chemical Initiatives? business. Umbogintwini?s J Plant manufactures sulphuric acid. The plant was designed and built by Simon Carves, and was commissioned in 1974. The plant was designed to produce 500 tons/day of Sulphuric acid (H2SO4) at maximum rates. The Sulphuric acid manufacturing is through the famous contact process whereby liquid Sulphur is injected through dried air in a burner operating at 1000 °C to form sulphur dioxide (10.5% SO2). The SO2 gas is then cooled in waste heat boiler no. 1 before being fed to a four pass converter which provides 99.5% SO2 conversion to sulphur trioxide (SO3). The SO3 gas is the absorbed by 98.5% H2SO4 through the inter-pass & final tower to make more concentrated acid and dilute it with water back to 98.5% H2SO4 in acid pump tanks and dispatched to storage tanks. The manufactured Sulphuric acid is supplied to a variety of industrial manufacturing customers includes Pulp & Paper industry, Mining industry, Chemical manufacturing industry etc.

Jan 1, 2009

By Robert Hopler

In accordance with the 57th section of the Explosives Act, 1875, the following report on the working of the Act during the year ending December 31, 1903, is submitted. There have been no modifications of the law during the year. No complaint is made of any falling off in the general condition of factories and magazines, and in one instance only during the year have legal proceedings been taken for any irregularity. The occupiers of factories and magazines have invariably shown perfect readiness to remedy any defects, and the managers have themselves in many instances introduced improvements tending towards greater safety. The number of deaths (5) from accidents by fire or explosion in the manufacture of explosives is below the average for the decade (6•4). Looking to the large number of persons employed in this trade, the number of deaths is not excessive and will compare favorably with the death-rate in other dangerous trades. Notwithstanding the large increase in the manufacture of explosives, the average number of deaths has greatly decreased since the passing of the Explosives Act, whereas the number of fatal accidents with explosives under conditions to which the Act does not apply appears to increase with the extension of trade.

Jan 1, 2006

By A. L. Williamson, G. Savci

Hydrologic assessments of existing and proposed waste rock stockpiles (WRS) are typically required for application of operating and closure permits at mine sites. The results of these assessments can be used to determine the applicability of the state groundwater permit program requirements to the operation and closure of these stockpiles. The objective of this hydrologic assessment was to ascertain whether or not the WRS at the Ajo Mine have a reasonable probability of discharging potential pollutants to the underlying aquifer under the operational mine conditions. The hydrologic assessment was performed based on an evaluation of climatic data, prediction of the net infiltration rate through the WRS and prediction of additional hydrologic factors such as the time required to deplete available moisture storage in WRS. The predicted net infiltration rates ranging from 0.13 inches/year (1.1x10-8 cm/s) to 0.24 inches/year (1.9x10-8 cm/s) are below the threshold value of less than 10-7 cm/s recommended by Hutchison and Ellison (1992) as being characteristic of conditions that produce no or negligible quantities of seepage. In addition, the total time required to deplete available moisture storage within the Ajo Mine WRS and for any potential seepage from the WRS to reach the underlying aquifer is estimated to range from 260 years to 1,950 years. Collectively, the climatological and geotechnical investigations and the hydrologic predictions demonstrate that the WRS at the Ajo Mine hydrologically do not have a reasonable probability of discharging pollutants to the underlying aquifer. As a result of this prediction, the stockpile will not be regulated under the state groundwater permit program and operational and reclamation requirements will be limited to managing surface water runoff.

Jan 1, 2002

"For effective steel refining in the ladle (secondary steelmaking) the amount of steelmaking slag that is transferred from primary steelmaking must be limited, because the steelmaking slag contains iron oxide, manganese oxide, and phosphorus oxide. Adverse effects of slag carry-over include increased consumption of deoxidizers, phosphorus pick-up by the steel, and increased ladle refractory wear. Infrared imaging at longer wavelengths is an effective non-contact method to detect slag in the tapping stream. Various devices are used to shut off the tapping stream rapidly. These include slag darts, pneumatic slag stoppers, and slide gates for steelmaking converters, and eccentric bottom tapping for electric arc furnaces. IntroductionOxygen converters and electric arc furnaces are used for primary steelmaking. For both process types, the product (liquid crude steel) has a similar composition: largely liquid iron, with around 800–1000 parts per million (ppm, by mass) dissolved oxygen and low but significant concentrations of carbon, nitrogen, and phosphorus. The steel is tapped into a ladle, which serves as the refining vessel to adjust the final steel composition and temperature before casting.Some steelmaking slag is inevitably tapped with the liquid steel. The mass of steelmaking slag tapped with the steel is termed ‘slag carry-over’. Controlling and limiting slag carry-over from steelmaking is a primary requirement for clean steel production (Fandrich, Lüngen, and Wuppermann, 2008). Steel cleanliness refers to limiting the concentrations of dissolved impurities (such as nitrogen, oxygen, phosphorus, and sulphur) and of nonmetallic inclusions (oxides, sulphides, and nitrides) in liquid steel and in the final solid steel product. Of these, the strongest effect of slag carry-over is on the content of dissolved phosphorus in the liquid steel"

Jun 1, 2019