Search Documents

By Robin B. Dill, Mark Pelletier, Daniel J. Dobbels, Subodh Bhaumik, Daniel J. VanRoosendaal

Although primarily cut-and-cover excavations are required for replacement of the existing elevated I-93 interstate highway through the heart of Boston for the Central Artery/Tunnel (CA/T) project, some mined tunnel construction was also undertaken. The mined tunneling conducted was the 22-m-wide northbound roadway structure which passed below a 20-m-deep operating underground subway station that was built in 1913. The innovative underpinning scheme used to support the subway station during construction resulted in the successful mining beneath the subway station with negligible vertical settlement. Two grouting galleries were carefully mined below the subway structure, and pre-grouting of the granulary, pervious glacial soils and weathered bedrock was carried out from these galleries. The reinforced concrete walls of the underpinning structure were constructed within three stacked drifts that were sequentially mined below each grouting gallery. After 11 cross adits were mined between the grouting galleries, cast-in-place post-tensioned girders that spanned between the stacked-drift walls were constructed to support the subway station. The stacked-drift walls also provided lateral support for the 22-m wide by 29-m long by13-m high opening beneath the girders.

Jan 1, 2001

By H. E. Biber

DURING the production of tin plate a thin layer of FeSn2, is formed at the interface between the steel sheet and the protective tin coating. Because excessive amounts of this alloy layer are undesirable, the kinetics of its formation is a subject of interest in the tin-plate industry. A recent study of this subject at our laboratory uncovered a relationship which should be of general interest to anyone studying kinetics of reactions in metallic systems. It had been previously concluded that, at any given temperature in the range 175" to 330°C, the Fe-Sn alloy layer would have a parabolic growth rate.1,2 However, our studies showed that this rule apparently holds only when the tin plate is heated very slowly to the "reaction" temperature; when the tin plate is rapidly heated, considerably different growth rates occur. An example of this effect of heating rate on growth behavior is contained in the accompanying results of alloy-layer growth measurements at 240°C in oil baths stirred at 10,500, 1800, and 0 rpm. The heating curves for these three conditions are given in Fig. 1, and the growth data are presented in Fig. 2. With the rapid heating rate, provided by the stirring at 10,500 rpm, the alloy layer had three distinct stages of growth. In the initial stage, which persisted well beyond the time required to heat the tin plate to bath temperature, the alloy layer formed very rapidly. The growth followed a rate law of the form w = ktn where n > 1. This initial stage was followed by a growth-retardation stage of about 50-sec duration in which little additional alloy was formed. In the third stage the growth again followed a rate law of the form w = ktn, but here « =0.3. With the intermediate heating rate provided by stirring at 1800 rpm, the three-stage nature was less pronounced and the slope of the third stage increased (i.e., n > 0.3). With the slow heating rate provided by the unstirred oil bath, the alloy layer grew in two stages. The initial rapid-growth stage persisted only until the specimen was heated to bath temperature, no growth retardation was observed, and the slope of the main portion of the plotted data was greater than in the stirred baths, having a value of almost 0.5. Similar results were obtained for other bath temperatures in the range 200" to 300°C. This effect of heating rate on growth behavior may be due to changes in the rate of nucleation of FeSn, crystallites. The iron and tin are in contact from the onset of heating. Thus the initial formation of FeSn, occurs not at the "reaction" temperature but rather while the tin plate is being heated to that temperature. Because nucleation is in general temperature-dependent, different heating rates could cause different over-all nucleation rates, which in turn could cause different growth behaviors. A more detailed discussion of the growth of Fe-Sn alloy layer and the effect of heating rate will be published shortly.

Jan 1, 1965

By N. Charue

An international prediction event was carried out within the framework of a 30-pile testing program organized in a sandy soil in Belgium (Limelette). That program called upon sev­eral testing methods: static load tests, Statnamic testing, and dynamic testing. This paper provides a summary of received predictions and results obtained from the static pile load tests, which were carried up to failure of the instrumented piles. The comparison between predictions is made using load-settlement curves with reference to the results of the static load tests. The predictions are based on a geotechnical approach using an extensive soil investigation program and a dynamic approach using the dynamic load test data.

Jan 1, 2002

The alkaline ethylenediamine tetra-acetic acid (EDTA) leach process for extracting tungsten from scheelite (CaW04) ores has been examined for the treatment of low grade (<0.5 per cent WO,) residue dumps. The process has been considerably simplified by applying solvent extraction directly to the leach liquor.Ammonium paratungstate is thereby produced in a one step process and this obviates the need to physically recover EDTA prior to recycling. This modified process should be an economical method of tungsten extraction.

Jan 1, 1983

By Shi Hongchao, Zou Zou Xinkuan, Zhang Jichun

As drilling and blasting is carried out in an urban tunnel, which is adjacent to an existing building or structure, the balance between blasting-induced vibration reduction and drivage efficiency is a most important issue that must be resolved properly. Therefore, a new cut blast method named Stepped V-cut millisecond blasting (SV-cut) was developed by optimizing the most common used Vertical V-cut blasting method (V-cut). The most significant features of SV-cut lie in the utilization of sublevel interval charging structure and millisecond delay blasting technology in cut hole and the cut-cavity formed from outside to inside sequentially. SV-cut provides advantages of high borehole using ratio, low vibration level, and satisfied advance per attack. Based on the principal of millisecond blasting, the rock fragmentation process and the vibration reduction mechanism of SV-cut are analyzed. Determining methods of blasting parameters, which do have significant effect on vibration intensity and cut-cavity formed quality, are proposed according to the forming requirement of both outer and inner cut-cavity and vibration reduction. In order to compare the performance between SV-cut and V-cut, field blasting experiments were performed in the blasting engineering of Yamalike twin-arc tunnel, which closely passes over aged parallel tunnels. Blasting results show that SV-cut blasting is proven as an effective tunnel blasting method for both increasing blasting effects and decreasing blasting vibration. Comparing SV-cut with V-cut, the SV-cut can increase blasting drivage about 8.5% and reduce the vibration intensity induced by cut hole blasting 30% at least.

Jan 1, 2015

By E. Sharifi

Advanced Process Control (APC) has been one of the most beneficial tools in the past decades available to minerals processing industry. Low capital cost together with significant improvements in process optimization have made APC an attractive investment option for nearly all mineral processing units. During economic downturns, importance of process optimization becomes even more relevant as metal producers tend to target de-bottlenecking and process efficiency improvements rather than large-scale capacity upgrades. APC project clearly has a lot of potential to improve process performance but there are also some pitfalls to be identified and avoided in order to achieve a desired outcome. Above all, APC project implementation is collaboration between the system vendor and user. Targets for the optimization must be agreed together with the customer and process performance must be defined before and after the optimization project. Most importantly, performance of the process must be monitored on a continuous basis during and after the project and potentially improved further. This paper discusses Outotec’s experiences from various concentrator optimization projects. Some examples are discussed in more details; however, the main target is to present general guidelines enabling a successful APC project implementation.

Jan 1, 2014

By C. J. Roos

Ground engaging tools are used to prevent damage to the main components of earth-moving equipment. These tools consist of everything from shovel teeth to replaceable drill bits to dozer wear plates. The costs of these ?consumable? items are increasing with the costs of raw materials. This project developed a tool to be used by Newmont Mining Corporation to predict the consumption of excavator teeth. This paper presents the results of a Montana Tech research project in which an equation was developed to predict excavator teeth consumption based on production rates and rock properties.

Jan 1, 2009

By Harry Asche

The last 12 months has seen the construction of the first Earth Pressure Balance (EPB) TBM excavated tunnel in New Zealand on the Project Hobson sewer storage tunnel for Watercare Services Limited, with the concurrent excavation of the second EPB tunnel on the Rosedale Outfall project for North Shore City Council. Together these tunnels involve a total length of 6km and follow an 8 year pause in TBM activity in Auckland. TBM performance on these two projects is thus of significant interest as there are four major tunneling projects totaling over NZ$8B being planned for Auckland, in similar ground conditions. Auckland?s bedrock is a weak sandstone/siltstone (East Coast Bays Formation), subject to infilled paleovalleys. The geology in the region has been significantly influenced by volcanic activity; 49 volcanoes are present within 20km of the city centre. The paper describes the design and construction challenges for the projects, including TBM performance, ?sticky spoil? management, and risks associated with basalt lava flows and two paleovalleys. Watercare?s Project Hobson also saw the successful implementation of a Geotechnical Baseline Report?one of the first uses of this type of document in Australasia. Rosedale Outfall is designed for high internal water pressures with varying hydraulic flows, with the risk of exfiltration explicitly addressed.

By G. Norman Owen, Roger E. Scholl

INTRODUCTION The analysis and design of underground structures to resist vibratory motion due to earthquakes has been of interest to engineers for several decades. The dynamic stability of a powerhouse cavern was considered in the 1960s (Campbell and Dodd, 1967). About the same time, the designers of the San Francisco Bay Area Rapid Transit system developed procedures for analyzing the subaqueous tunnels placed under San Francisco Bay and the tunnels excavated along the land portions of the alignment (Kuesel, 1969). Japanese designers developed fairly sophisticated procedures for analyzing subaqueous tunnels during the late 1960s and early 1970s (Kuribayashi et al., 1974). In the past decade, proposals to site important critical underground facilities in regions with moderate to high seismic activity have increased the interest in earthquake engineering of underground structures. Seismic designs or seismic studies have been conducted for rock caverns for storage of petroleum or location of power plants (Yamahara et al., 1977; Glass, 1976), buried tanks for fuels or rad¬ioactive waste (Fukushima et al., 1977; URS/Blume, 1976), tunnels for disposal of nuclear waste (Yanev and Owen, 1978; Wahi et al., 1980), and urban mass transit tunnels (Monsees and Merrit, 1984). One of the greatest drivers of the interest in seismic analysis and design of underground structures has been the proposals to dispose of high-level nuclear waste in mined repositories some 300 to 600 m (approximately 1,000 to 2,000 ft) below the ground surface. In 1979, the authors, in conjunction with Professor Tor Brekke, presented a paper on an evaluation and design procedure used in a study of a proposed nuclear waste repository (Owen, Scholl, and Brekke, 1979).

Jan 1, 1985

By E. Nickel

"Bi- and multilateral banks as well as export credit agencies in the OECD countries, but also numerous commercial banks, last year committed themselves to compliance with the World Bank’s standards. These environmental and social guidelines, also known as the Safeguard Policies, are the strictest international standards in the area of financing of major investment projects. The Safeguard Policies are procedural and quality guidelines by means of which socially and environmentally relevant impacts can be taken into account in the planning and implementation phase of a project. Objectives of the Bank Safeguard Policies are to ensure that environmental and social issues are evaluated in decision-making, to reduce and manage risk of projects and programs, and to provide a mechanism for consultation and disclosure of information. They are often referred to as the "10+1 Safeguard Policies," since ten of the guidelines address environmentally and socially relevant issues, while one guideline is exclusively concerned with public participation ("Public Disclosure"). In the presentation, the transparency of risk management measures and emergency response plans in pipeline projects will be discussed as an indicator of sustainability. The discussion is to be carried out on the basis of the results of an evaluation of several major pipeline projects, which have been financed at least in part by multilateral banks over the past few years. The controversies surrounding some of these projects due environmentally and socially relevant impairments connected with the investments have also been addressed by the Extractive Industry Report of the World Bank. Pipeline construction was the investment type chosen for the examination to be presented here, since pipelines frequently start in remote, unspoiled regions, and their routes often cross various natural zones and areas with various social structures. The question of safety during construction and operation of the line is always central to these projects; not only for the responsible authorities but also for other societal groups involved, such as environmental associations."

Jan 1, 2005

By Lawrence Williamson, Randall J. Essex, David P. Field

As part of a $2.2 Billion bridge project that will link Indiana and Kentucky, an interchange project northeast of Louisville will require the mining of a 6-lane tunnel system about 2,000 ft long in order to cross beneath the historic Drumanard Estate. This paper will discuss preliminary engineering that has been undertaken to compare two-bore and three-bore layouts, the planning of an exploratory tunnel facility, and the potential for including a test chamber to investigate the ability of high capacity roadheaders to mine the 22,000 psi limestones.

Jan 1, 2005

By Robert B. Bittner

"AbstractLarge diameter tubular piles offer significant advantages in terms of design performance and economy for major marine structures. This is particularly true for foundations of major overwater bridges in regions of high seismicity such as the west coast of North America. The use of large diameter piles in the range of 2 to 3 m diameter means that fewer piles are required, and the size and mass of the pile caps can be significantly reduced, thereby greatly reducing lateral load demand during seismic events. Another advantage of using larger diameter piles is increased pile stiffness that allows the pile caps to be located at or near the waterline rather than being positioned at or below the mud line. This elevating of the pile cap offers significant cost savings by eliminating the need for deep cofferdams. However, relocation of the pile cap creates new problems and opportunities in regard to the means and methods used to construct the pile cap. With the pile cap at depth, conventional steel sheet pile cofferdams with thick tremie seals are typically used to isolated the cap location and allow dewatering for construction of the cap. However with pile caps positioned up off the bottom, conventional bottom founded cofferdams are no longer cost efficient. Float-in or lift-in cofferdams have been developed to address the need for a more cost efficient method for cap construction. This paper describes the key features of the concept and provides three case history examples of its successful implementation.Pier Construction Using Conventional Sheet-Pile CofferdamsCofferdams are temporary structures used in the construction of bridge piers and other marine structures. Their primary purpose is to hold out water and unstable soil from the construction area, and thereby, allow in-the-dry construction of the permanent structure below the water line and quite often below the mud line. Typically, cofferdams consist of long interlocking steel sheet piles driven through water into the bottom of the waterway. The sheet piles form temporary exterior walls which are typically braced internally with wales and struts. The bottom of the cofferdam is typically sealed with tremie concrete or an impervious clay layer if one exists. The depth at which this type of cofferdam can be used is typically limited by the length of steel sheet pile that can be transported and handled by conventional marine equipment."

Jan 1, 2014

By M. A. W. Bryson

Platinum group metals are extracted almost exclusively in South Africa from three very different zones in the Bushveld Igneous Complex, called the Plat, Merensky, and the UG-2 reefs. The Plat reef is currently being exploited only by Anglo American Platinum, whereas the Merensky reef is exploited by them, Impala Platinum, Northam, and Lonplats. The UG-2 reef, on the other hand, is also processed by these producers, but Kroondal and Barplats have operations that exclusively treat ore from this reef. At present the extraction of pgms from ores in South Africa follows the traditional route of upgrading to a concentrate in a minerals processing circuit, further upgrading to a matte in a smelter, and final upgrading and separation of the individual metals in a refinery. Thus all operations that extract pgms require a minerals processing circuit, the design and performance of which is a topic of much interest, as it is a poorly understood and not a very efficient process in relative terms, compared to the other processes. Recoveries across the minerals processing circuit of between 75 and 90% are the norm.

Jan 1, 2004

By Peter Zhang

Shield recovery in a longwall move is normally conducted from tailgate to headgate. However, if the face is wide and the immediate roof is weak, difficult conditions with considerable roof sag, excessive shield load, and local roof falls could occur as the shield recovery proceeds to the middle of the face, causing delays in shield recovery. The situation could be aggravated when a pre-driven longwall recovery room is employed. Alternatively, a bi-directional approach for shield recovery, i.e. shield recovery starting from the middle of the face towards both tailgate and headgate, can alleviate the roof sag significantly by quickly withdrawing the shields towards the lower abutment pressure zones at the headgate and tailgate sides. In this case, the bi-directional shield recovery approach was used in a longwall move for a 1450 ft wide face under weak roof conditions. Shields were successfully withdrawn within five days without experiencing significant roof sag. The time-dependent roof-to-floor convergence, shield pressure, and roof conditions were monitored during shield recovery. 3-D finite element modeling was conducted prior to longwall move to evaluate the difference between a uni-directional and a bi-directional shield recovery during a longwall face move. Vertical stress, yield zone in and around the recovery room, load on the shields, and convergence at the center of the shield canopy were obtained from computer modeling, and compared with the data from field monitoring. Finally, the advantages of the bi-directional shield recovery are discussed.

Jan 1, 2007

By E. Northcott, F. N. Oberg

By electrostatic separation, course Florida pebble phosphate, too lou-grade to find a ready market, can be upgraded to a satisfactory saleable product. Pebble running from 60 pct bone phosphate of time may be upgraded to 73 to 77 pct BPL depending on the mineralogical. structure of the pebble and the nature of the silica innpurity. High-grade concentrates from Florida pebble phosphate deposits have long been recovered by wet methods. When work was begun in the field, only the coarse pebble (generally +1 mm) was re- covered. In the 1920's a froth flotation process was developed to separate quartz from the finer phosphate fractions, but this method proved unsatisfactory for treating the intermediate fraction (—1 mm +35 mesh). Consequently various other processes were adapted, including agglomerate tabling and spiral separation of reagentized feed. Today the three processes are used—washing and screening for coarse pebble, tabling or spiraling for intermediate sizes, and flotation for —35 mesh material.

Jan 1, 1959

By Sanna Mustonen, Seppo Mellanen, Mellanen, Pekka Kantia

In Finland Posiva Oy (Company) is responsible for implementing the final disposal programme for spent nuclear fuel of its owners. Company is preparing for the geological disposal in Olkiluoto crystalline bedrock. Excavation will be executed using drill and blast method. Method unavoidably causes variable excavation damaged zone (EDZ) on tunnel surfaces. The EDZ constitutes a risk for long term safety and therefore good control methodology of the blasting technique is required. The thicker the EDZ, the greater is the likelihood for detrimental transport pathways for ground water to transport radio nuclides, should those be present.

Jan 1, 2016

By Kung-Lee Wang

SUSTAINED growth characterized the U.S. economy in 1964. Many new peaks were achieved in production, sales, employment, employee earnings, and business profits. At the end of 1964, the economy had experienced 4 years of uninterrupted expansion, and the greatest net gains in output for all postwar cyclical advances had been registered. There were no indications of the various weaknesses which have previously characterized advanced stages of business expansion. Both gross national product (GNP) and national income were 6.7 percent higher than in 1963. In 1964 GNP totaled $628.7 billion, a gain of $39.2 billion over the 1963 figure. On an overall basis, prices rose 1.75 percent in 1964. The real volume of output of goods and services (GNP in constant dollars) increased by 5.0 percent ill 1964; this was more than the 3.8-percent gain in 1963 but less than the 6.6 percent gain in 1962. The 1964 output gain also exceeded the average 3.7 percent annual increase for the postwar period. Congress authorized a two-stage tax reduction designed to further stimulate economic growth and employment. The tax cut favorably affected the 1964 economy in the following ways: By helping to boost personal income, corporate profits, and industrial production; by accelerating the pace of consumer spending and business capital expansion; and by increasing employment, thereby reducing unemployment to 5 percent. Three major problems remained unsolved. These were unemployment of 3.7 million persons, poverty conditions among more

Jan 1, 1965

By Jean Cayouette, Paul Blatter, Paul Cousin

"The Laronde mill was commissioned in 1988 and has been treating the Laronde Penna ore since 2000. The Laronde plant, situated in the Abitibi region of Quebec, has experienced mill expansions to accommodate 7500 mtpd and to recover gold and silver as well as important amounts of base metals (Cu, Zn, Pb). Ten sequential metallurgical and environmental processes are responsible for metals recovery and process viability. Over 200,000 ounces of gold, 4,5 million ounces of silver, 7000 tonnes of copper, and 78,000 tonnes of zinc are produced annually.In 2008, the Goldex plant began trucking high grade (35-45 g/t Au) pyrite sulphide concentrate (TCGO) for gold extraction at a newly constructed treatment plant, increasing gold output at Laronde by 40,000 ounces. In 2009, the high gold grade Lapa ore processing facilities were annexed to the Laronde plant increasing output by 120,000 ounces of gold. TCGO and Lapa productions are forecasted until 2018 and 2015 respectively, with known reserves of each mine.Today, up to 140 permanent employees run and optimise the Laronde plant operation. As a result, Laronde has intricacies intrinsic to a large and varied operation. The paper will outline the metallurgical highlights, challenges, and future outlook related to the treatment of each ore type (Laronde, TCGO, and Lapa).INTRODUCTIONFollowing the 2000 to 2003 expansions, the Laronde plant evolved into a mature milling complex with developed processing, man power, and water treatment capabilities able to accommodate the complex Laronde ore. The ore requires a series of grinding, copper/lead flotation and separation, zinc flotation, zinc tails precious metals leaching, followed by a counter-current decantation circuit and Merrill Crowe precipitation. A paste backfill and SO2-air cyanide destruction operate intermittently. The tailings area has a dedicated cyanide destruction and metals precipitation plant prior to water recycling to the mill. A biological water treatment plant was put into service in 2004 to address the build-up of thiocyanate in the tailings ponds at Laronde. This was the result of the high sulphide content of the Laronde ore and 90% recirculation of the process water. The plant uses bacteria to oxidize and destroy thiocyanate, and removes phosphate from the water before it is released to the environment."

Jan 1, 2011

By J. P. D. Strydom

The transmission of excessive vibration to the human body can cause physical stress that may result in crippling pain or permanent disability. Rock drills are known to transmit high levels of vibration that are difficult to attenuate through conventional approaches to vibration isolation. However, it can be shown that once the ISO frequency weighting has been applied, most of the vibratory effect of the rock drill?s motion is concentrated at the drill?s operating frequency. This observation opens the way for utilizing a concept known as vibration absorption, aimed at attenuating the rock drill?s vibration. In essence this entails using the inertia of a secondary vibratory system to counteract the motion of the handle. This article documents an investigation into the use of such an absorber for attenuating rock drill vibration and demonstrates the feasibility of such an approach. A mathematical model of such an absorbing handle was developed and used for design studies. Based on these investigations an experimental prototype model was manufactured and tested. A significant reduction in vibration levels could be achieved.

Jan 1, 2002

By C. O. Karacan

Underground longwall mining of coal causes large scale disturbance of the surrounding rock mass. The disturbance can increase the rock mass permeability through a reduction on the stress as well as formation of new fractures in the rock. Methane gas contained in the disturbed rock mass can migrate towards the low pressure mine workings and present an explosion hazard. This paper describes the application of a finite difference program to develop a geomechanical model that predicts permeability changes within the rock mass. The calculated permeabilities are used as input to a reservoir simulator that models methane desorption from the coal matrix, methane release from the rock layers and flow towards the mine excavations. The model also considers the basic characteristics of the mine ventilation network. The geomechanical model uses empirical relationships between fracture permeability and stress to calculate permeability changes around a longwall face. The extent of rock failure is determined using a strain softening model that considers both rock matrix and bedding plane failure. The cave rock (gob) is modeled as a compressible, granulated material. The calculated horizontal and vertical permeabilities around the longwall face are averaged and used as one of the inputs to the reservoir model. The reservoir model was developed and calibrated against records of methane flow at a study mine in southwestern Pennsylvania. Good correlation between actual gas production and model outputs has been achieved. The modeling approach provides a basis for estimating methane inflow and optimizing control measures.