Search Documents

During the drilling campaign conducted between October, 1942; and May, 1943, to prove the extent of the scheelite deposit worked by King Island Scheelite N.L. at Grassy, King Island, Tasmania, 35 holes were drilled and 606 samples recovered and assayed for their content. Of these, 238 came from outside the limits of the orebody and were for the most part barren, although a few contained some scheelite. The present statistical analysis is made only of the 368 samples taken from diamond-drill cores of the orebody itself.Drilling Pattern and Sampling MethodsFrom the purely statistical viewpoint, it is realised that methods employed in selecting sites for diamong.-drilling, and of collecting samples from drill cores, do not give a completely unbiassed set of data for analysis. Fig. 1 is a sketch plan showing the relativepositions of the drillholes, which were inclined at an angle of depression of 50 deg. The pattern does not conform to a properly randomized and' regularly-spaced grid, the positions of the later holes being determined by the results obtained from previous holes.Statistically, the bias is, therefore, favourable. The unequal spacing of the drill holes and the lack of uniformity in direction of the lines along which the holes were drilled are unsatisfactory from the mathematical viewpoint; but it is realised that these irregularitiesare difficult to avoid in determining by the most economical methods the extent of such an orebody, and are dictated by geological rather than mathematical necessity.Sampling, also, is lacking in complete uniformity. Each sample is approximately 10ft. in length. However, owing to the fact that 100% recovery of core is rarely achieved, and actual lengths of samples taken are ,primarily governed by the length of the drill runs,and secondarily by lithological changes, there is a considerable amount of variation in the sample length.AssayingWith the exception of 28 samples from three drill holes all samples dealt with in this paper were assayed in the Melbourne University Ore-Dressing Laboratory of the Commonwealth Scientific and Industrial Research Organisation. These assays were given to the nearest 0.05% WOg as it was considered that more accurate determination was not possible. This fact has been taken into consideration in the frequency analysis below. The 28 assays determined by the Tasmanian Mines Department were given to the nearest 0.01%.

Jan 1, 1950

By Susan B. Robertson, Gregory E. Hinshaw

Many injuries are caused each year by rock falls in coal mines. Most of these injuries are not caused by major roof collapses, but from falls of smaller rocks from the immediate top or roof skin. Various surface controls are used in mines to control this surface rock. One that has been found to be very effective is roof screening. Depending on the size of the screen, roof coverage approaching 100%can be achieved. Many mines are reluctant to use screen for primary skin control because of additional costs of time and materials, but others are having great success at both controlling costs and surface rock. Data is presented from two mines that show a dramatic reduction in roof skin injuries when screening is used. Much of this success is due to innovations in roof bolting machines. Four case studies of roof screen experience are presented along with associated costs of materials, impact on bolting advance rates, and potential ergonomic risks. The effects of roof screening on skin control and safety are also included. Finally, this paper will provide information about features of different roof bolting machines that affect production and safety.

By D. Allan Coutts

Demonstration projects using hydrogen as a fuel are becoming very common. Often these projects rely on project-specific risk evaluations to support project safety decisions. This is necessary because regulations, codes, and standards (hereafter referred to as standards) are just being developed. This paper will review some of the approaches being used in these evolving standards, and techniques which demonstration projects can implement to bridge the gap between current requirements and stakeholder desires. Many of the evolving standards for hydrogen-fuel use performance-based language, which establishes minimum performance and safety objectives, as compared with prescriptive-based language that prescribes specific design solutions. This is being done for several reasons including: (1) concern that establishing specific design solutions too early will stifle invention, (2) sparse performance data necessary to support selection of design approaches, and (3) a risk-adverse public which is unwilling to accept losses that were incurred in developing previous prescriptive design standards. The evolving standards often contain words such as: ?The manufacturer shall implement the measures and provide the information necessary to minimize the risk of endangering a person?s safety or health.? This typically implies that the manufacturer or project manager must produce and document an acceptable level of risk. If accomplished using comprehensive and systematic process the demonstration project risk assessment can ease the transition to widespread commercialization. An approach to adequately evaluate and document the safety risk will be presented.

May 1, 2007

Silver is one of the three major metals produced from the Broken Hill mines. The accurate determination of the silver in these ores, therefore, is of economic importance.With due appreciation of the divergence of opinion of many who are interested in the subject of the determination of silver, the writer has been prompted to present the results of some recent experiments on silver losses during cupellation and conclusions from these experiments in the present paper. The losses of silver in the fire assay for this metal are due to silver retained in the slag during the fusion or scorification of the ore, and to silver volatilized from, and absorbed by the cupel during the process of cupellation.The literature describing the results of experimental work on silver losses due to the above causes is extensive, and the general conclusion of these experiments is that the silver lost in the slag is small, but that lost by cupellation is larger and more variable.The term cupellation loss in this paper refers to the total cupellation loss, no distinction being made between the absorption and volatilization losses.Volatilization loss is shown by King to be 0.5% of the total cupellation loss and, as it is generally accepted among assayers as being only a small fraction of the cupellation loss (3) (5), it will not receive further consideration in this paper.The factors causing the loss of silver by cupellation and the precautions to be obs~rved to reduce the loss in this operation are described in (1), (2), (3), (4) and (5). The...

Jan 1, 1940

By Svetlana Nikitina

While many question "sustainability" as an intellectual field on the grounds that it is too broad and "undisciplined," we are able to achieve a good balance between breadth of coverage and depth of inquiry in our team-taught seminar "The Grand Challenges: Sustainable Development for the 21st Century" offered to first year students at Worcester Polytechnic Institute. We strike this balance between breadth and depth by a) problematizing key sustainability issues in class discussions; b) by explicitly exploring the lenses of different disciplines (the historical context, the scientific facts, the engineering interventions and the philosophical foundations of unsustainable behaviors); and c) by offering our students opportunities to pursue a targeted project on specific sustainability issues (vertical gardening, metals recycling on college campus) through which they gain depth of understanding as well as practical exposure to all components of the problem, which puts them on the path of seeking effective solutions.

Jan 1, 2010

By John Popovich

The MICON RokLok binder system including component and consolidation processes and safety and its first aide are described. The implementation procedures and selection of injection parameters are discussed. Finally a case example of recovering a 30-ft. long roof fall in mainline haulage entry is used to illustrate the economic potential of preventive measures by RokLok injection.

Jan 1, 2001

By R. Amelunxen

"The molybdenite associated with copper porphyry ores is generally treated in a flotation circuit consisting of a separation and a cleaning section. In the last few years column flotation cells have replaced the numerous counter-current stages that were previously used in the cleaning section. Despite this, little has been published regarding the number of column cleaning stages required. Therefore a Moly flotation database is assembled with the objective of verifying the existence of a common upgrading profile. This can then be used as a guide in the prediction of the number of stages required to achieve a given concentrate grade.INTRODUCTIONAlthough the first use of Column Flotation was on copper flotation products, the popularity and understanding of their operation was not really achieved until they were widely implemented in Moly circuits in early 1983. The use of columns in Moly plants has since left a legacy of information, both published and unpublished. The data collected since that time has been used primarily used to establish column operating parameters and to determine upgrading potential within the circuit.Byproduct Moly generally occurs with porphyritic copper ores in concentrations less than 0.1% MoS2. As such, piloting a new moly ore to produce, say 5 Kg/Hr MoS2, in a slurry approximately 1 Lt/min (at 10% solids), requires a moly plant feed of about 570 Kg/Hr, which translates to a mill feed rate of 200 to 800 Tonnes per day (depending whether you deal with Chilean or Canadian ores). Piloting Moly for any lower tonnage would reduce the accuracy of the testwork.Thus a need exists to collect operating data in order to establish the existence of process relationships that could be used for feasibility and design purposes.The object of this paper is to expose a preliminary relationship that could be used for the purposes described above and to apply the findings to a preliminary design of a moly cleaning circuit flowsheet."

Jan 1, 1990

By H. A. Steane

"This presentation will cover some crushing and grinding considerations in plant design and operation. There is nothing basically new in the subject matter presented here; however, the viewpoint and interpretation may be novel and some of it controversial.The presentation is based on experience gained in the metallurgical design of plants for Placer Development Limited from 1960 to the present. The plants are listed on SLIDE No. 1.These plants have conventional crushing, followed by rod mill and ball mill grinding. I would like to think that autogenous grinding plants are the answer for eliminating secondary crushing plants and reducing the capital and operating costs; however, the autogenous plants seem to have some problems of their own and I have had no experience with them.Fineness of Grinding RequiredFirst let us consider the fineness of grinding required.The fineness of grind will affect the recovery obtained, and the relationship must be determined. If the grinding is too coarse, some of the valuable mineral, either free or locked in middling grains, will not be floated. However, as grinding is probably the greatest single operating cost, we do not want to grind any finer than is justified economically.Finer grinding should not be carried beyond the point where the net smelter return for the increment saved becomes less than the added operating cost. Even this fineness will be beyond the economic limit because of the additional capital cost for the equipment needed to achieve it. These factors will be discussed in more detail later.The Bond work index is the commonest method of expressing a measure of the effort that has to be expended in grinding. It is the kilowatt-hours required to reduce a ton of rock from an infinite size to 80% passing 100 microns. The formula allows a calculation to be made for other size ranges."

Jan 1, 1976

By John H. Weigand, Stephen V. Crum

"VIBRONICS, INC. instrumented and monitored a residential structure for response to,blasting at aMidwestern surface coal operation. The residence was owned by the mining company and was extremely close to the operation. Blasting was conducted within 120 feet (36.5 meters) of the test structure. Up to seventeen (17), four (4)-channel seismographs were used during the monitoring period. The basement walls and floor were monitored. VIBRONICS, INC. also monitored a brick chimney in the basement and attic. Structural responses were then compared to outside vibration measurements taken in the soil near the foundation."

Jan 1, 1998

By Jamal Rostami, Ebrahim Farrokh

Selection of tunneling method, specially the use of shielded machines for application in deep rock tunnels can be heavily impacted by presence of ground convergence and squeezing conditions. Tunnel convergence is a function of ground conditions (i.e., rock mass behavior, groundwater, in-situ stresses), size of the opening, and TBM operational parameters. The case study of Ghomroud water conveyance tunnel project in Central Iran, which is under construction using a double shield TBM, is used to examine the effect of rock parameters on tunnel convergence and hence on the need for over excavation and shield lubrication to avoid problems with the shield getting stuck. Although it is impractical to perform a continuous assessment of rock mass conditions within the shield or in the lined tunnel, results of field observations and subsequent studies show that the amount of the tunnel convergence has direct correlation with the percentage of fines and large rock fragments in the muck and TBM thrust/torque/ROP. These relationships have been examined and will be presented in this paper.

Jan 1, 2007

Study on Mineral Processing for a Cassiterite Ore in Southwest China

Sep 13, 2010

Population growth, social inequality, pollution, global warming, poverty, overexploitation of natural resources and biodiversity loss, are a few examples of the many challenges facing the world today. Sustainable development is about meeting these challenges and improving the standard of living for the benefit of the maximum number of people. These issues concern governments, communities, environmental and social action groups and individuals all over the world. Business too, has a fundamental role to play in delivering sustainable development. In particular, sustainable development is becoming increasingly recognised as a critical issue for the oil and gas industry to address and act upon. BP is committed to positively respond to the challenges posed by the objective of sustainable development.

Jan 1, 2002

By Stig O. Olofsson

The problem of overbreak in underground construction and mining is normally approached by a variety of smooth blasting methods. Numerous small diameter, low velocity explosives have been developed specifically for blasting the contour line. Increased mechanization in rock excavation has led to the development of several methods of mechanical explosive loading. A new mechanically loaded smooth blasting explosive was developed in Sweden . However, several limitations were realised, which after several trials resulted in a hybrid smooth blasting method, The Suaer Cautious Contour Blasting Method which will be discussed in this paper.

Jan 1, 1994

By Malcolm Ross

Asbestos crystallizes within rock formations undergoing intense deformation characterized by folding, faulting, shearing, and dilation. Some of these conditions have prevailed during formation of the taconite iron ore deposits in the eastern Mesabi Iron Range of Minnesota. This range includes the Peter Mitchell Taconite Mine at Babbitt, Minnesota. The mine pit is over 8 miles long, up to 1 mile wide. Fifty three samples were collected from 30 sites within areas of the pit where faulting, shearing and folding occur and where fibrous minerals might occur. Eight samples from seven collecting sites contain significant amounts of ferroactinolite amphibole that is partially to completely altered to fibrous ferroactinolite. Two samples from two other sites contain ferroactinolite degraded to ropy masses of fibers consisting mostly of ferrian sepiolite as defined by X-ray diffraction and TEM and SEM X-ray spectral analysis. Samples from five other sites contain unaltered amphiboles, however some of these samples also contain a very small number of fiber bundles composed of mixtures of grunerite, ferroactinolite, and ferrian sepiolite. It is proposed that the alteration of the amphiboles was caused by reaction with water-rich acidic fluids that moved through the mine faults and shear zones. The fibrous amphiboles and ferrian sepiolite collected at the Peter Mitchell Mine composes a tiny fraction of one percent of the total rock mass of this taconite deposit; an even a smaller amount of these mineral fragments enter the ambient air during mining and milling. These fibrous minerals thus do not present a significant health hazard to the miners nor to those non-occupationally exposed. No asbestos of any type was found in the mine pit. © 2007 Elsevier Inc. All rights reserved. Keywords: Taconite; Asbestos; Amphibole; Reserve mining; Tailings; Mesabi iron range; Mineral fibers

Jan 1, 2007

By C. J. Martin, M. P. Hay

"A methodology was developed in the mid-1980’s to predict plant performance from standard laboratory flotation tests. The technique is based on a simple, empirical kinetics model, and is tailored for use by the practical metallurgist.To date the performance of more than 20 flotation plants has been predicted, including copper, lead, zinc, phosphate, pyrite, graphite, cassiterite, platinum, nickel and various slags. The method has successfully been used to predict and size four flotation plants directly from bench-scale laboratory flotation testwork. All have since been commissioned, and have performed as predicted.The technique has now received broad acceptance within the South African mining industry, for example in the last year alone it has been used to drive flowsheet development for at least seven new plants. It is also being used to assist in the optimisation of existing operating plants.The methodology is described in this paper and verification of the methodology is presented using case studies of porphyry, polymetallic and PGM operations.INTRODUCTIONThere is considerable interest these days in the use of modelling to simulate flotation circuits, for process design and plant optimisation purposes. Although these models are proving to be useful tools for plant design and optimisation, their complexity can make them cumbersome – expensive to use and difficult for metallurgists to visualise and mentally absorb, without a background in each specific technique. In “SUPASIM” no attempt is made to measure flotation fundamentals, rather to use empirical relationships between laboratory flotation kinetics and plant performance – relationships that hold up well to validation exercises as will be demonstrated later in this paper. Although not designed to be as comprehensive as other models, “SUPASIM” is easily understood by the operating metallurgist and can be quickly and easily applied."

Jan 1, 2004

By Åke Krukka, Heribert F. Broicher

"The iron ores of the Kiruna Mine in Sweden are of exceptional quality but for the phosphorus content in certain zones of the orebody. The prevention of mixing ores high in phosphorus with those low in phosphorus has always been of significant economic importance. The ongoing introduction of tele-mining and automatic haulage by LHDs requires new means in the field of quality control underground, as the experienced miner as well as the underground laboratory assistant no longer are involved in the process. As of 1998 LKAB has been testing prototypes of LIF Analysers for non-contact and real-time measurement of the phosphorus content of ore being transported by LHDs from the stopes to the respective ore pass assigned to a certain ore quality. The principles of the analysis of laser-induced fluorescence, the different test phases and results are described and conclusions made. With bulk sorting of ore underground the mining engineer supports the efforts of the metallurgist in the processing plant.INTRODUCTIONThe Kiruna Mine of LKAB, Sweden is the largest underground iron ore mine in the world. In the early nineties LKAB decided to develop the Kiruna orebody further down from the 775m main level to a new main level at 1045m. This development programme was realised while in the mineral processing section and in the pellet plant further capacity was added (Wyllie 1996).In addition to deepening of the mine, which opened up 330 million tonnes of ore, the exploitation of the so-called lake ore was included in the future planning, adding another 1 15 million tonnes of mineable ore. At an annual production of approximately 20 million tonnes of ore the Kiruna Mine today looks at a developed ore reserve sufficient for the next 20 years.All of the competitors’ ores traded in the world market are from open pit operations. LKAB compensates for the obvious disadvantages by continuous efforts to make the best possible use of her high quality magnetite ore deposit. This objective is realised by combined efforts in the pellet plant, the mineral processing plant and the mine. Propriety processes, latest big scale equipment and high tech solutions for automation lead to high quality sales products at a reasonable cost."

Jan 1, 2002

By Hargraves A. J

The paper outlines events at the Collinsville State Coal Mine, Queensland, leading to the practice of full face multiple shotfiring in bord and pillar development places. The 1954 disaster is referred to, and factors involved in simultaneous shotfiring in coal are discussed. Promising preliminary multiple shotfiring tests at the Colliery are described, as well as the resulting routine measures adopted, and the changes involved. The subsequent inducing of two outbursts under safe conditions by remote multiple shotfiring is given as justification for the changes made.INTRODUCTIONFollowing a disastrous instantaneous outburst (1.0.) of coal and gas at the Collinsville State Coal Mine in 1954, the necessity for inducer shotfiring for the control of possible further outbursts was established. However this mine, immediately classified as gassy after the 1954 outburst, is subject to the general restrictions pertaining to gassy mines which at present preclude the use of inducer shotfiring due particularly to the non-existence of a permitted exploder for more than six shots, and further, because permitted multipleexploders are not designed for remote firing through long lengths of cable. This situation was met by arresting or reducing progress in the production places, thereby reducing the danger of outbursts while means were being considered to achieve overall maximum safety.In August 1957 two full faces were successfully blasted in experimental simultaneous rounds. In June 1958 four full faces were blasted, and in October 1958 full face grunching without prior cutting, Le. inducer shotfiring, was introduced in No. 1 Tunnel as a production feature. In March 1960 it...

Jan 1, 1960

Using Positron Emission Particle Tracking (PEPT) to Investigate Industrial Systems

Sep 13, 2010

By A. Lane

The socio economic risks of mining in South Africa have been emerging for some time now, and have been brought into sharp relief by recent events in the platinum sector. The slow pace of social upliftment in the country has lead to widespread social unrest with consequent calls for different forms of resource nationalism. Fundamentally, the key stakeholders are not fully aligned, and are not engaging productively. This poses significant above-the-ground risk to mining companies. Measuring social impact, deploying inclusive solutions and engaging effectively with stakeholders are three ways in which mining companies can mitigate this risk.

Jan 1, 2013

By Dana C. Reinke

A job analysis is a written list of the tasks associated with doing a particular job. In drilling, describing the steps associated with adding rod to the drill steel would be an example of a task associated with the job. How to hammer casing or fish a lost drill bit out of a hole would also be job tasks. Develop a written list of job tasks. Ask drillers in your company if the tasks listed are correct and accurately reflect how to perform the job. While each driller may do the job a little differently, some tried?and?true methods are required to perform certain tasks safely and correctly. You may find a separate analysis is needed for different drilling jobs (e.g., a residential well or a monitoring well). Also remember to include the tasks of both the helper and the driller.

Jan 1, 2005