Search Documents

By Carlos Avalos Casillas, Saul Ortiz Landeros

The current work shows metallurgical results obtained at the Centro de Investigación y Desarrollo Tecnológico (Peñoles CIDT), as a continuation of the work first published in February 2012. With the aim of optimizing the economic values of the products, ores from San Julian (Fresnillo) were selectively floated to produce a lead concentrate and a zinc concentrate containing high silver values. In the laboratory, this included regrinding of the rougher and scavenger lead concentrate to increase the liberation of mineralogical species and thus lower zinc recovery. Cyanide leaching bottle tests were conducted to improve the value of the silver. It is proposed to leach the silver contained in the zinc concentrate and then recover the silver using the Merrill Crowe process. The results show a reduction of zinc recovery in the lead concentrate from 11.3% to 2.0% after regrinding to a P80 of 10 microns, improving the metallurgical quality and economic value of the lead and zinc concentrates. Also laboratory and pilot scale cyanidation tests showed that about 65 to 80% of silver will be leached from the zinc concentrate, after regrinding to a P80 of 10 microns. The proposed processing increases the economic recovery of silver from 72.7% to 78.8%.

Jan 1, 2014

By Gabriel Esterhuizen, Tom Goodwin, Scott Schilling, Anthony T. Iannacchione

The Roof Fall Risk Index (RFRI) is a new method introduced by the National Institute for Occupational Safety and Health (NIOSH) to assist the underground stone mine operator in 1) assessing defects the mine strata and 2) rating the relative roof fall risk these defects pose. The RFRI utilizes observational techniques to identify defects in the roof strata caused by local geologic, stress, and mining conditions. Assessment values for ten defined defect categories provides the foundation for estimating a range of risk conditions between 0 and 100 that define the potential for a roof fall. This paper examines how the defect information is collected using two field verification sites and proposes methods to analyze the RFRI data. These examples provide information on how well the method replicates observed conditions and how it might be applied in practice.

Tumbling mills and some theoretical and practical aspects of milling are discussed. Attention is directed towards the difficulty of relating the dynamical analyses of the motions of particles within mills to the existing treatments of breakage processes. This synthesis may be advanced by a study of milling that utilizes the matrix analysis of breakage processes. Application of the matrix analysis to results obtained on (i) grinding in open-circuit a zinc ore in a conical pebble mill and in a modified conical mill, (ii) "grinding of cement clinker in a compound mill, and (iii) to some drop-weight grindability tests is discussed. It is shown that the 'IT-breakage model adequately describes the breakage processes of each of the tests. (The proportion broken in each breakage cycle is given by 'IT and is independent of particle size.)The size distributions of the products are accurately predicted in the cases considered. Matrix analyses of the breakage of coals, various ores and a cement clinker have been made. Appendices give an elementary account of the matrix methods and give the equations fully describing reverse order closed circuit operations. The matrix analyses of breakage processes and the survey are used to examine briefly closed circuit grinding.INTRODUCTIONTumbling mills are slow-speed crushing and grinding machines which have been developed from some fairly simple types into many widely differing forms. Many of these versatile mills have proved extremely useful in ore dressing and mineral beneficiation, whereas others have been used in the cement industry and less extensively in the coal industry.The performance of even the simplest tumbling mill is very imperfectly understood, whilst the more difficult problems associated with the balancing of complex milling circuits and with the establishment of the optimum operating conditions for the whole of a complex circuit are even less well apprehended.Our knowledge of the performance of tumbling mills is rather sharply divided into two categories: the first consists...

Jan 1, 1957

Pressure drops were measured in a column packed with glass spheres and wax particles, both in random and preferential distributions. Variables investigated included wax content, gas flow rates, and temperatures.It is shown that for random distribution of wax, pressure drop is exponentially related to wax content above the melting point of wax and that below this it increases with increasing gas rate and temperature.For preferred distribution of wax the highest increase in pressure drop is obtained with horizontal distribution of wax and the least with vertical distribution.Comparison with operating blast furnace data and application of results to practice are also included.

Jan 1, 1970

By R. J. C. MacDonald

"The first recorded discovery of placer gold in Canada was on the Chaudiere River in Quebec's eastern townships in 1832 and the first major production came from placer deposits in British Columbia in 1858 (Verity 1974). Placer deposits were the major source of gold until the late 1890's, although lode deposits were found in Nova Scotia in 1862. In 1896 the Klondike Gold Rush commenced with the discovery of gold by Henderson and Carmack in the Yukon. The peak was reached in 1900 when over one million ounces of gold valued at approximately $22.3 million were recovered. With the exhaustion of the easily accessible deposits, more capital intensive operations were necessary such as those initiated in 1906 by the Yukon Gold Corporation. This giant dredging operation continued to produce until 1966. Today only a few small operations remain.The development of Canadian lode gold mining began in earnest around 1900 when the railroads were opening up the interior and western part of the country. At this time many discoveries occurred, particularly where mineral outcroppings were near surface. Tremendous impetus for exploration and the reopening of former producers followed the elimination of the gold standard by Great Britain around 1931, and more importantly the United States in 1933, with subsequent stabilization of the price of gold at $35 per ounce in 1934. Prior to this the price of gold was basically unchanged since 1717, approximately, $20 per ounce (Verity, 1974; Green, 1973).The depression of the 1930s adversely affected most industries, however for the gold producers it was a very profitable time. Prices of materials and equipment declined and labour was cheap and plentiful. Interest in gold mining was further stimulated in 1936 when a three year tax exemption was declared for all new metal mines. In 1938 a decline in the value of the Canadian dollar relative to the U.S. dollar benefitted the industry. The second world war provided yet again further incentive for gold production and in 1941 Canadian gold production reached a high of approximately 5.4 million ounces. This figure was not surpassed until 1991 when approximately 5.6 million ounces were produced (Natural Resources Canada, 1996 )."

Jan 1, 1998

By Shepherd J

Megascopic and microscopic studies of cleats and mining induced cleavage in Ihe first workings at Leichhardt Colliery reveal the presence of four distinct fracture sets. Microscopic studies confirm underground observations of the fracture sets.The most likely order of formation of the fractures is (i) "butt" cleats (ii) facc cleats (iii) shallow dipping faults (iv) mining induced cleavage. Three fracture sets apparently formed by tensiIe failure. Microscopy shows that the mining induced cleavage surfaces have preferred starting or lerminating points at the extremity of a "butt" cleat and a vitrite-dull coal band boundary. It is postulated that the induced cleavage begins at 'butt' cleats which behave as Griffith flaws under high compression around Leichhardt Colliery faces. Instantaneous outbursts of coal and gas are associated with only those workings which are affected by mining induced cleavage and occur at or adjacent to working faces.

Jan 1, 1981

By E. J. Efsic, C. M. Wayman

The fcc to bcc y to a transformation in an Fe-24.5 at. pct Pt alloy was studied and found to be martensitic. Large martensite plates are formed in this alloy which are ideal for crystallographic studies; the Ms temperature is about -5°C. Ordering of the parent phase prior to transformation to martensite causes a pronounced lowering of the Ms temperature. For the first time in the case of alloys of iron, measurements of the habit plune, orientation relationship, and magnitude and direction of the shape stvain have been obtained on preselected martensite plates. It is shown that by measuring the initial and displaced (as a result of the shape strain) positions of three or more non-parallel fiducial scratches on one reference surfice the maguitude and direction of the shape strain and the state of distovtion at the parent-mavtensite interface can be determined with a reasonable degree of accuvacy. The agreement between the phenomenolog-cal crystallographic theory of martensitic transformations and the experimental results habit plune, orientation relationship, and nlagnitude and direction of the shape strain) is essentially perfect, and is thought to be the best reported to date for iron alloys. THE comparatively few investigations on binary Fe-Pt alloys have been concerned with magnetic properties, ordered phases, and the equilibrium diagram itself. Various investigations have shown that the equilibrium diagram is of the open y field type; in addition there is a peritectic transformation, a minimum melting point, and three ordered phases: Fe3Pt, FePt, and FePt3. The results of a number of investigators1-6 have shown that the temperature dependence of the y to a (and reverse) transformation in iron-rich alloys is reasonably well-established. The Fe3Pt phase was first noted by Kussman and Rittberg,7 and its existence was later confirmed by Franklin et al,8 Steijn and Donahoe,9 and Berkowitz et al.10 The FePt phase was reported by Isaac and amman' and later confirmed by a host of others.3,6,7,12,13 Kussman and Rittberg7 noted the existence of the superlattice FePt3. Prior to 1956, the 1 to a transformation in iron-rich Fe-Pt alloys was termed "irreversible". In 1957 Klokholm and Donahoe" termed this transformation martensitic, presumably because of its occurrence at temperatures well below those where diffusion normally takes place. This observation served as a point of departure for the present investigation, and in the very early stages of the work to be discussed it was readily verified that the y to a transformation in iron-rich Fe-Pt alloys is indeed martensitic. Quite large martensite plates exhibiting the well-known surface tilt were observed. These plates are ideal in the sense that the boundaries between the parent and product phases were usually very straight. It thus appeared that Fe-Pt martensites would be ideal for crystallographic studies, and this was the purpose of the present investigation. Details of the crystallography of martensitic transformations (particularly for iron alloys) and the phe-nomenological crystallographic theories15-l7 have been discussed many times and thus will require very little elaboration here. The end result of these theories, given in matrix form, is

Jan 1, 1968

By W. R. Dengler, R. S. Brown

In 1974, Brunswick Mining and Smelting Corporation Limited started a 48 million dollar expansion programme at their property in Bathurst, New Brunswick. A portion of the expansion plans includes a 26 foot diameter 4,525 foot deep shaft, underground crusher and conveyor excavations and lower level access development. J. S. Redpath Limited was awarded the contract for the new shaft and associated rock work in May 1974. Brunswick Mining and Smelting Corporation Limited, a member of the Noranda Group, operate this 10,000 ton per day lead, zinc, copper plant with proven reserves in excess of 90 million tons. While most of the ore is provided by the underground operation at the Number 12 ore body, some tonnage is produced from the open pit at the Number 6 ore body. Long range plans indicate a phasing out of the open pit and an increase in production from the underground operation. Existing facilities at the underground mine could not provide additional tonnage, thus the requirement for a new shaft. (Figure 1) The new shaft will also provide access to ore below the 2,800 level which is currently the bottom level of the existing facility. The contract called for sinking a 26 foot inside diameter, nine compartment concrete shaft 4,525 feet deep (Figure 2). Station access and ramp development from existing workings would be required to the bottom of the new shaft. In addition, development work for new crushing and conveying facilities was needed simultaneous with the shaft sinking.

Jan 1, 1976

By Charles Pretorius, Henk Ludik

Navachab Mine experiences difficulties with pit wall stability in certain areas of the mine. The main reason for the instability is the fact that the geology comprises many joints and faults. Blasting, without impacting negatively on the stability of the pit walls, poses a major challenge.

Jan 1, 2006

By J. A. Meech, G. R. Baiden

"A dynamic simulation of a mine-mill complex has been conducted using networked microcomputers (IBM PC/AT and IBM PC/XT). These models allow simultaneous operation of an open pit using shovels and trucks, a primary crusher, and a secondary crushing plant. Each process transmits information via the network, linking all operations together. The effects of blasting, ore quality, equipment utilization and configuration on productivity can be studied either interactively or from a report listing at the end of each shift. Programs are menu driven leading the user through the decisions required in day to day operations. The mine-mill simulator is currently being used as a teaching tool at Queen's University to provide senior mining and mineral processing engineering students with an experience and appreciation for the operating problems across the mine-mill interface. The need for coordination and close communication between the mine and mill can be aptly demonstrated using these models. The simulator could be used to contribute to the training of operating personnel in a real mining operation. INTRODUCTIONThis paper describes a computer simulator that is capable of showing the interactions and operating strategies between a mine and a secondary crushing plant. The simulator uses two models developed at Queen's University; one for open pit mining and the second for secondary crushing. PITSIM is a dynamic shovel/truck haulage model origin2lly developed by P.D.D. Chick (1) and K.G. Fytas (2) to solve shovel/truck scheduling problems. CRUSHSOFT is a dynamic secondary crushing plant model developed by R.J. Tucker (3) and C.A. Harris (4) to study alternative operating and control strategies in a crushing plant."

Jan 1, 1987

By R. W. Bartlett

DISILICIDE coatings, MeSi2, on refractory metals are usually grown by a solid-state diffusion reaction similar to the parabolic oxidation of metals. Two or more silicide compounds occur in each of the binary silicon-refractory metal systems. When an adequate source of silicon is available during the coating process, the lower silicide compounds are usually not formed.1 However, during service application of the coated refractory metal, continued heating causes further diffusion and growth of the lower silicides. A study of the growth kinetics of the lower silicides in the molybdenum and tungsten binary systems with silicon was previously reported.2 The present study is concerned with the growth kinetics of Ta5Si3 and Cb5Si3, formed as conjugate layers between TaSi2/Ta and CbSi2/Cb diffusion couples, respectively. Diffusion couples consisting of disilicide-coated tantalum and columbium sheet coupons were subjected to diffusion heat treatments, cross-sectioned, and scanned by an electron-microprobe analyzer to determine the relative X-ray intensity profiles. These profiles correspond closely to concentration profiles for the constituents, and were used to identify phases and locate phase boundaries. The analysis of a single specimen after a diffusion-anneal provides only one value for the Me5Si3 phase thickness, corresponding to the time and temperature of the diffusion treatment. Consequently, each isothermal curve showing the rate of accumulation or depletion of silicide phases required several samples with identical diffusion temperatures but different diffusion times. The disilicide coatings were prepared by pyrolizing commercially pure silane in a hydrogen carrier gas. The hydrogen was purified by passage through a palladium membrane. Commercially pure tantalum and columbium sheet metal coupons, 0.005 by $ by 2 in., were used. All of the coated specimens for each system were prepared together in a single group in order to minimize coating variations among individual specimens. During pyrolysis, the brightness temperature was maintained at 1200°C. With suitable flow rates at this temperature, only the disilicides of tantalum and columbium were formed in detectable amounts. Coated specimens were subjected to diffusion an-neals in a tube furnace with automatic proportional control within ±10°C. A H2-Ar mixture, deoxidized and dried over anhydrous magnesium perchlorate, was used to prevent oxidation during the diffusion anneal. Diffusion couples were cross-sectioned, polished and examined with an A.R.L. electron-microprobe X-ray analyzer. Both metal constituents in each specimen were simultaneously scanned using a 1-p beam spot size and either 1- or 2-µ steps. Analyses were performed using the Ka radiation of columbium and silicon, and the La, radiation of tantalum. For all specimens, an acceleration voltage of 30 kv was used, and integration was made against the specimen current. LiF and A DP monochrometers were used to isolate characteristic radiations. Three or more traverses were made on each specimen. The intensity scales were adjusted using the constituent metals and standard samples of the silicide compounds which had been verified by X-ray diffraction. The relative intensity profiles were used directly, in conjunction with the standard samples, to identify compounds and phase boundaries. The stoichiometries differ considerably between the silicide compounds in both systems, and the homogeneity range for these silicide compounds is narrow. These characteristics result in marked differences in relative intensities of the fluorescing elements—differences which permit ready identification of phases and phase boundaries. Projections of both electron back-scattered images and characteristic

Jan 1, 1967

The early development patterns of both Australia and New Zealand were substantially in parallel and both were heavily indebted to gold mining for, providing the stimulus to growth. However, since the mining boom, of 1895 - 1899, the mining sector in New Zealand has progressively declined, while in Australia it has assumed an increasing importance in the economy. The continued dominance of minerals in Australian trade, and the fact that eight out of the top ten companies in Australia are directly involved in mineral exploration and production, has strongly influenced government and public attitude's to the minerals sector. Although the legal framework of mining and exploration Acts and Regulations are similar it is in, the method of administration, particularly in regard to exploration and prospecting licences, that the gulf across, the Tasman is apparent. Despite the relative ease of application and granting of licences in Australia, in the more settled south eastern part of the continent we are finding more and more land is being zoned unavailable for exploration. In the remote areas, the Aboriginals now control nearly ten per cent of the land area of Australia, virtually with drawing that portion from exploration. The concept of 'Australianisation' has softened a hardening attitude against foreign investment in mining on the part of the bureaucracy. This anti-mining attitude is fortunately, not shared by the public, and we can but hope that the will of the Australian people can filter through to our masters in Canberra, and ease the rapid increase in the number of regulatory bodies which does so much to inhibit the normal conduct of business. The delays caused by interminable hearings and committee investigations all cost money. This cost can only rebound back on the end consumer, who after all is a voter.

Jan 1, 1982

The Hyde-Macraes Shear Zone (HMSZ) is low angle, duplex thrust system that has developed in a graphitic pelite schist within the Otago schist belt, New Zealand . At Round Hill lateral ramps have developed parallel to the movement direction between+ the footwall and hangingwall shears. These structures exhibit normal oblique-slip displacement which has been an important mechanism for creating space in an otherwise compressional system. Gold-bearing quartz veins were emplaced along the boundary shears and lateral ramps during thrusting. Gold within the lateral ramps is coarse (up to 300 microns) however hanging wall cataclasite development in the boundary shears after the gold was deposited has reduced the grainzise of most of the gold to less than one micron. This bimodal gold distribution has metallurgical implications with respect to the maximisation of gold recovery at Macraes.

Jan 1, 1993

By P. Sklenicka

Remediation of the environmental (and social) disturbances caused by opencast brown coal mining in the past in north-west Bohemia isa priority for state environmental policy. In order to provide a concept for full restoration of land following disturbance by opencast mining, a special interdisciplinary project supported by a grant from the Czech Ministry of Environment was started in 2000. The initial stage of the project was intended to summarize and evaluate the findings and the works carried out in connection with various reclamation activities in the afflicted area over a period of more than 50 years. The main aims of the three-year project are to make use of the best available landscape environmental management knowledge in order to harmonize the ecological, aesthetic, productive and social functions of new valuable landscape, including the recovery of historical continuity and an understanding of ?landscape memory?. The basic landscape functions were assessed on two different scale levels. On a large scale, the relevant attributes were investigated over the whole area of the Sokolov brown coal basin (220 km2). The data and experience acquired were used to define large-scale guiding principles for the rehabilitation of a post-mining landscape. On a small scale, the basic characteristics and functions of the landscape were analysed in the Litov-Chlum model area (2 km2). The information derived from this analysis was used to formulate a small-scale approach for the rehabilitation of the model area and also to define general methodological principles. Keywords: rehabilitation, post-mining landscape, degraded landscape, non-productive priorities

Jan 1, 2004

By N. Ahmed

The collection of hydrophobic particles in the froth phase in flotation has been studied. A continuous flotation cell was developed, in which the froth phase could be isolated from the pulp zone. Hematite particles, d80 = 87 µm, were floated in the pulp, using a conventional oleate collector, while glass spheres of similar diameter, d80 = 82 µm, were introduced in wash water added to the froth. Four samples of glass spheres, with contact angles between 0 and 82 degrees, were used. The results indicate that the efficiency of collection of the hydrophobic particles in the froth can be very high. The process is strongly influenced by the hydrophobicity of the particles and the surface area available for attachment in the froth. Recommendations for the flotation of particles in the froth phase are made, especially regarding the desirable hydrophobicity as reflected in the contact angle, the froth depth, the solids concentration in the feed to the froth, the air rate and the wash water rate.

Jan 1, 2001

By Kenneth B. Higbie

METALLURGICAL ACTIVITY in 1963 was again dominated by the insatiate demands of research and development conducted in conjunction with the nation's defense and aerospace programs. An increasing effort was noticeable throughout the year, however, to apply to the commercial field many of the processes and techniques that have been developed by government-sponsored research. Particularly effective has been the Industrial Applications Program of the National Aeronautic and Space Agency through which many of the technological advancements made during the course of NASA research and development have been published and released to the public. POWDER TECHNOLOGY Powder metallurgy techniques for fabricating metals, not long ago declared outmoded because of improved casting and shaping methods, have since made an astonishing comeback. Traditionally mechanical pressing of powder shapes has been employed when melting and casting was difficult or impossible, when phase relationships needed to be sidestepped, or when machining costs could be avoided. Hence, it has long been used for producing relatively small special shapes of high-melting metals and alloys. Small iron parts produced with a punch and die have been common for many years, but powder metallurgy techniques are now applicable to a wide range of materials and items. Hard-to-handle materials including refractory metals and their alloys are now rolled, forged, or extruded from billets made by sintering isostatically compacted powders. The major element of the powder metallurgy industry still comprises iron shapes, however, and two-thirds of the annual 100,000 tons of powder metallurgy products are made of iron. The largest single user of powder-forming techniques is the automobile industry which currently consumes 14,000 to 16,000 tons of iron powder per year. A typical 1963 model auto contained more than 100 pressed powder parts (e.g., transmission gears, timing gears, sprockets, ball joint suspensions) totaling 5 to 7 pounds per car. Some of these powders are used in self-lubricating parts of porous copper and copper alloys containing as much as 20 volume-percent lubricating oil. The expanded use of powder techniques, coupled with

Jan 1, 1964

By G. A. Grandy, P. F. Thomas, C. D. Danecki

When considering the mill drive system for a grinding application, a large number of questions must be answered. Depending on the mill size and type, the mill can be driven by several configurations of drive systems: a single low-speed motor connected to a pinion driving a ring gear, two low-speed motors connected to two pinions and driving a ring gear, or a gearless motor mounted directly. In addition, a gear drive system can have a reducer placed between a high-speed motor(s) and pinion(s) or a power path splitting pinion stand. In some designs the reducer is integral with the pinion stand driven by a high-speed motor. The technical and commercial implications of several mill drive options are presented. Initial cost, cost of installation, cost of commissioning, and cost of operation and maintenance are presented for each drive option considered. The impact of each drive system on the design, cost and operation of the overall plant electrical system is discussed. Also, consideration is given to mill drive availability, and the potential cost resulting from delays in plant production.

Jan 1, 2001

By Vincent Tirolo

The proposed Second Avenue Subway is a new two-track subway line running from 125th Street and Park Avenue at the north, east along 125th Street to Second Avenue and south along Second Avenue to the Financial District in lower Manhattan, NY with 16 new stations and 13.6 km (8.5 miles) of track. The project has been broken into four construction phases. The initial Phase 1 operating segment includes three new stations (96th, 86th and 72nd Street stations) with a connection to the existing Broadway line at the 63rd Street Station at Lexington Avenue. Rehabilitation of the 63rd Street Station is also included in the scope of Phase 1. Subsequent phases extend service north and west to 125th Street (Phase 2), south to Houston Street (Phase 3) and finally to Hanover Square (Phase 4). The DMJM Harris/Arup Joint Venture (DHAJV) prepared the Contract Documents MTA for Phase 1. Parsons Brinckerhoff is providing the MTA with construction inspection services for Contract C-26002. In April 2007, NYCT awarded first Phase 1 for $337 million to S3 Tunnel Constructors, a tri-venture comprised of Skanska USA Civil, Schiavone and Shea. Contract C26002 is for the construction of the tunnel boring ma-chine (TBM) launch box and the mining of the TBM tunnels from 92nd Street to 63rd Street. The major part of the contract is to construct a shaft, commonly referred to as the launch box, from East 92nd Street to East 95th Street having dimensions of 244-m- (800-ft-) long by 18.9-m- (62-ft-) wide and a depth of 19.8 m (65 ft), including more than 91,000 m3 (119,000 cu yd) of soil and rock contained within its walls. The launch box will ultimately become the southern half of the 96th Street Station. The focus here is geological conditions at the launch box and existing structures along the launch box. These geologic conditions and existing structures had a major influence on the selection and design of the support of excavation system (SOE), the SOE bracing system, construction staging, the ground movements, dewatering and other challenges of constructing the launch box (Fig. 1).

Jan 1, 2013

By Grey CA

Any economic evaluation of a lead-zinc mining project requires the estimation of net revenue per tonne of concentrate at the "mine gate". The value at the mine gate equals the Net Smelter Return minus all realisation costs. The paper develops a simple predictive model for Net Smelter Return based on metal prices.

Jan 1, 1990

By Stewart A. Silling, Dale S. Preece

The two key results of rock blasting are fragmentation and movement of geomaterials. Movement/flow of the blasted rock is often referred to as heave. Modeling the movement of full scale blasting is now possible with 3D distinct element models and parallel processing.

Jan 1, 2016