Search Documents

By S. Ross, M. Mayhew

"Kirkland Lake Gold introduced battery equipped vehicles (BEVs) at the Macassa Mine in 2011. The fleet of underground BEV haulage trucks and loaders has grown over the years to over 30 units, the world’s largest, currently handling approximately 80% of the daily production tonnage. The inflow and outflow of air occur through a limited number of relatively small openings, which limits the air volume delivered to the underground workings. In addition to improving air quality, the reduced heat load generated by the BEV (when compared to diesel equipment) had a significant positive impact in the workplace. The use of BEV for material handling has enabled increases in production that would not have been possible using diesel equipment.INTRODUCTIONMacassa mine was developed as a track-drift access mine, with the most recent shaft (#3) sunk in 1986. A new mining complex, the South Mine Complex (SMC) was discovered below the 5025 foot elevation south of traditional mining areas, and the majority of mining now occurs in the SMC. The discovery of that zone has led to an internal ramp which is used to access the SMC and haul ore to #3 shaft.The amount of airflow that can be moved through the mine is limited by the existing infrastructure to surface. This amount was recently increased to near its practical maximum from 118 CMS (250 kCFM) to 151 CMS (320 kCFM).Both diesel and electric equipment are used at Macassa. Tethered Load-Haul-Dump Machines (LHDs) have been replaced with Battery Electric LHDs, due to their increased mobility and depth of the mine. Battery trucks continue to replace locomotives to transport both ore and waste to the shaft, as mining has transitioned from tracked levels to trackless level and haulage has transitioned from horizontal levels to an inclined ramp.EQUIPMENT FLEET AT MACASSAMost of the primary material movers utilized at Macassa Mine are battery operated. As the mine goes deeper the battery technology will continue to be critical to the success of the operations. With over 300,000 hours of proven operation success, the battery technology and equipment will continue to be a major part of Macassa’s future."

Jan 1, 2019

By J. Herhold, S. Plaum

The focus within the economical optimization of projects, which are conducted underground, shifts more and more towards the conduction of construction work underground. Underground operations can be defined in a wide range of various projects, from underground mining tasks to the construction of engineering structures. Within these projects the conduction of construction work cannot only be defined as absolutely necessary, but sometimes also as optimizing for underground processes (e. g. installation of workshops underground to support the mining processes). Even though the conduction of underground construction might cause positive outcomes concerning the productivity, it also tends to be challenging due to local (sub-surface) conditions and influences. To minimize the risk of failure and sudden events within in the conduction of construction work underground, the tool “work preparation” shall be used. Under the given constraints, such as local influences, expected construction work and set time frame, the conduction of the construction work will be planned in advance by consideration of the construction logistics as well as the selection of a fitted construction technique. PROBLEM DEFINITION Economic Challenges - Raw Material Extraction Enterprises in the construction, mining and raw material extraction industries are increasingly under the pressure to perform economically to sustain their position on the global market. Profitability, efficiency and productivity are the basic conditions to be an active participant on the global market as well as a business partner and contractor for mining and construction projects or projects related to the extraction of raw materials. The completion of large-scale as well as common construction projects above ground has been under the pressure to minimize costs and time whilst maximizing the potential outcome, in the meanings of quality and economic gain, for more than a decade now. Whereas the construction industry has to fight the competition on the market with efficient project outcomes, the mining industry has to find ways to perform efficiently to further conduct the extraction of decreasing raw material deposits. The ongoing exploitation of existing raw material deposits to satisfy the constantly increasing raw material demands world-wide, led to the predicament that economically mineable deposits have decreased dramatically. Even tough mineral deposits do still exist on a global level, near-surface deposits decrease rapidly. Therefore, the extraction of raw materials within mining operations will be relocated further away from the surface in greater depths. With the growing distance from the surface to the mineral deposit, the extraction costs will increase many times over. With that in mind, the extraction costs will increase whilst the economic efficiency will decrease. The extraction of certain deposits will no longer be profitable with the common approach. To further extract raw materials efficiently even in greater depth, companies have to change their practice in different ways. That leads to the fact, if the deposits are in the depths, where the extraction processes won´t be economically, other (support) processes have to be in order to guaranty an economical corporate process itself. This precept will divert the focus from the actual mining process to support processes, where potential for optimization still can be found, as shown in figure 1.

Jan 1, 2019

By C. Feng, W. Song, B. Moudgil, P. Zhang, W. Xiao

Separation of dolomite from phosphate is the most challenging problem in phosphate mineral processing. Over 50% of the future phosphate reserves in Florida contains too much dolomite to process using the current industry practice. The FIPR Institute has collaborated with worldwide experts in the field to address this issue. As a result, the industry is now offered with three feasible options. Optional 1 involves crushing and grinding of high-dolomite phosphate pebbles followed by dolomite flotation at slightly acidic pH using a new collector that does not require phosphoric acid as a phosphate depressant, achieving a final concentrate analyzing less than 0.9% MgO at about 87% P2O5 recovery. Option 2 offers three methods for reducing MgO content in the concentrate from the Crago process, including adding a dolomite depressant in the rougher flotation step, dolomite flotation of the cleaner concentrate, and scrubbing the cleaner concentrate in quartz sand. These methods could reduce MgO content in the final concentrate by 20-40%. Option 3 is a gravity separation technique using an innovative separation jig, and may well be the ultimate solution to the problem. INTRODUCTION Magnitude of the Dolomite Problem With the depletion of the higher grade, easy-to-process Bone Valley deposits, the central Florida phosphate industry has moved into the lower grade, more contaminated ore bodies from the Southern Extension. The phosphate deposits in the Southern Extension may be divided into two zones: an upper zone and a lower zone. The upper zone is readily processable using the current technology, but the lower zone is highly contaminated by dolomite. Geological and mineralogical statistics (Hassan and Bogan, 1994) show (Table 1) that more than 50% of the phosphate resource would be wasted if the lower zone is bypassed in mining, and about 13% of the resource would be wasted if the dolomitic pebbles in the lower zone were discarded.

Jan 1, 2019

By D. Hulse

Mineral resource classification is described in both the SME and CIM Standards for Mineral Resource Reporting. The CIM Standard states “… sampling … is sufficient to assume geological and grade or quality continuity between points of observation”, thus is a function of continuity and sample spacing. Continuity can be measured by use of a variogram model, but average sample spacing in three dimensions is more difficult to measure. The declustering algorithms provided with Geostatistics software, are commonly used to weight data for statistical analysis due to the sometimes-irregular spacing between drill holes during exploration. The weights are lower when data is closer, reflecting shared influence between samples, and higher for isolated samples reflecting independence. This paper will discuss the potential to use estimates of the declustering weight as an inverse relative measure for average sample spacing to gauge the confidence of the estimate independent of the single nearest sample. PROBLEM The classification of mineral resources and reserves has long been a combination of science, past experience of the estimator, judgment, and feeling. All of the definitions as presented in the standards of the various countries that participate in CRIRSCO are similar and deal with “sample points sufficiently closely spaced to support confidence in the continuity of …” This has been interpreted as the distance between the block estimated and the nearest sample (or samples). Geostatistics gave us the calculation of the estimation variance of the block, an implicit part of the calculation of weights in Kriging, to account for the confidence in the estimate. More recently, “Kriging Efficiency” has been used, however it is still dependent on the estimation error and responds in a similar fashion to the distance to the closest sample. It is also sensitive to the variogram nugget. Many of these methods result in very low distance/high confidence measures for blocks adjacent to a sample point with confidence decreasing (sometimes rapidly) as the distance to one nearest sample increases. This results in the “spotted dog” phenomenon where individual samples are surrounded by a higher classification near each sample decaying into pattern of decreasing confidence halos. In addition to the visual image of the spots, this raises the more practical problem of mine design when the classification changes between measured, indicated and inferred. This has led to ad hoc methods to classify material within the mining block so all of the stope receives that classification. These manual methods re both labor intensive and subjective. A popular technique is a multiple search method, where the estimator defines a minimum of number of samples from a minimum number of holes within a nested set of search distance that are used to classify estimates. These specified set of increasing distances are usually proportional to the variogram range. While this is generally a good technique and overcomes the spottiness of the closest sample or kriging error, it has certain issues including:

Jan 1, 2019

By Laura Steeves, Inoka Eranda Perera, Jhon Silva, Arend Spaeth

"This paper reviews the main concepts ruling the design, implementation and performance of active explosion barrier systems for underground coal mines in the USA. The document examines the parameters needed for the design of this type of system, such as overpressure and flame speed, suppressant deployment speed and duration time of the active barrier. The document also discusses the available solutions for gassy mines and the concepts behind the selection of machined mounted and roadway active explosion barrier systems. The paper includes a review of active explosion barrier systems developed in the USA and South Africa. The paper provides an overview of the current status of this technology in the underground coal mining industry in the USA, and the possible implementation of such systems. The paper concludes with the identification of the future work needed for the successful implementation of the systems in several conditions to enhance the safety of underground coal mine operations and to provide more tools to the miners for their safety.INTRODUCTIONUnderground coal mine explosions can be addressed in two ways, through prevention or mitigation. The United States mining industry practices have emphasized the prevention of explosions in underground coal mines, with little being done to mitigate the explosion once it occurs. Despite successful practices for the prevention of underground coal mine explosions in the US, the threat of an explosion does still exist. Other mining countries around the world have developed and implemented mitigation systems such as active explosion barriers in their underground mines. In the 1970s, the United States Bureau of Mines (USBM) carried out extensive research on the use of active or triggered explosion barrier systems in the US; however, they are not currently used.Explosion barrier systems do not prevent explosions but mitigate the propagation of the shockwave and flame to other areas of the mine. The use of active explosion barrier systems enhance the safety of underground coal mines. Active or triggered explosion barriers will detect the arrival of the shockwave or flame front of the explosion and release inert material to suppress or extinguish the flame. The technology required for active barrier systems is readily available based on their presence in other mining countries and must be adapted for their use in US coal mines. The adaption must consider the coal dust and methane concentrations in US coal mines, the mine geometry, and the mining equipment used."

Jan 1, 2019

By I. Silin, M. Stapelmann, H. Wotruba, K. M. Hahn, C. Gerold, J. Katzmarzyk

New deposits are often characterized as low-grade and complex ore bodies. To date, processing of fine grained ore deposits implies complex processing routes with high energy consumption. For that reason, the investigation of dry grinding, e.g. with vertical roller mills (VRM), is an approach to save energy reserves. It is already proven that dry grinding can influence subsequent processing steps. In terms of flotation, the surface characteristics of the minerals are crucial for a successful flotation process, e.g. the sufficient adhesion of mineral particles and air bubbles. Wet grinding results in different surface properties of the product entering the conditioning stage than dry grinding, which has direct influences on the subsequent flotation process. To investigate the consequences for flotation, processing of a copper sulfide ore containing chalcopyrite and bornite was investigated, including grinding and rougher flotation. The effects of wet tumbling mill and dry VRM grinding on the degree of liberation of valuable minerals are characterized using mineral liberation analysis by scanning electron microscopy. The obtained flotation results, as well as the recorded flotation parameters such as dissolved oxygen, oxidation reduction potential and conductivity are presented and discussed. INTRODUCTION Copper production is mainly connected to porphyry copper deposits as main source for copper sulfides such as chalcopyrite and bornite. State-of-the-art processing of these deposits is already established worldwide for decades, combining crushing, fine grinding and subsequent flotation with rougher, cleaner and scavenger stages (del Villar, Desbiens, & Maldonado, Bouchard, 2010). While the demand for copper is increasing, copper grades of the deposits are decreasing and the remaining ore bodies have more complex mineralogy and finer particle size distribution. This implies processing routes with high water and – due to the liberation of fine grained valuable minerals – high energy consumption by fine grinding. One of the main energy consumers in processing plants is the grinding section, which accounts for more than 50% of the energy consumption in processing plants and even 4% of the worldwide energy consumption (Jeswiet, & Szekeres, 2016). Therefore, dry fine grinding alternatives are applied to enhance the overall energy consumption of mineral processing plants: high pressure grinding rolls (HPGR) and vertical roller mills (VRM).

Jan 1, 2019

By Jaana Romppanen, Satu Jyrkönen, Tiina Ranki, Peter Björklund, Markku Lahtinen, Kaj Eklund, Päivi Suikkanen

Outotec is continuously developing our existing process equipment and new equipment solutions to enhance the Flash Smelting process. Thanks to the long operating history of the Outotec Flash Smelting process feedback from the numerous operating references are available and is utilized. The general goals for development work are to improve equipment performance, thus realizing savings in Smelter plant operation costs by increasing the process efficiency and online availability. Digitalization also opens new possibilities for the feeding equipment and furnace operation monitoring. These solutions will improve the safety and performance of the smelter, and provide process and equipment related information which has not been available earlier. INTRODUCTION The year 2019 marks the 70th anniversary of Flash Smelting. The technology was operated on industrial scale for the first time at the Outokumpu Harjavalta copper smelter in Finland in 1949. The Flash Smelting technology, is now owned and developed by Outotec Oyj and the first plant, is now owned by Boliden Harjavalta Oy. The two companies have been evolving throughout history by optimizing the process for various feeds and raw-materials, as well as through developing the equipment and operating practices. Even though sustainability was not a hot theme/topic during the first days of Flash Smelting, it has nevertheless been the key principle in guiding the development. This is well proven by the wide adoption of Flash Smelting for the processing of copper and nickel concentrates, mostly due to its ability to fulfil the economic and resource efficiency criteria demanded by its operators. Along with the process technology development, also development of the equipment has taken place over time. Outotec is continuously working on developing our equipment to better suit the changing need of our customers in the continuously changing operational environment. Orebodies are getting more challenging with lower ore grades and more impurities. Achieving high recoveries for all valuable elements becomes more difficult with high slag quantities and with the need to tackle the high impurity concentrations. There is a need for higher capacities in greenfield and brownfield smelters. The role of the Loss-in-Weight Feeder, the Air Slide and Concentrate Burner is to ensure even feed into the reaction shaft of the Flash Smelting Furnace, and to enable controlling the process well, thereby enabling the best performance for the customers smelter. The design of the Flash Smelting Furnace aims for high availability, long campaign and safe operation.

Jan 1, 2019

By H. Henao, E. Kohnenkamp, L. Rojas

The slags generated in the copper conversion process are mainly composed of Cu2O-Fe2O3-SiO2 with the compounds CaO and Al2O3 in concentrations up to 10 wt%. The present work contributes to the knowledge of the conversion process, generating experimental data for the diagrams of phases Cu2O-Fe2O3- SiO2-Al2O3 and Cu2O-Fe2O3-SiO2-CaO. The experiments were carried out in a tubular furnace at temperatures of 1150°C and 1200°C under a condition of saturation with tridymite. Once the equilibrium was reached, the samples were fast quenched in water. The phases in the samples were observed in a Scanning Electron Microscope (SEM) and the elemental composition of the phases analyzed by means of Energy-dispersive X-ray spectroscopy (EDS) detectors. The addition of Al2O3 and CaO into the Cu2O-Fe2O3- SiO2 system resulted in an appreciable displacement of the liquidus lines, corresponding to an expansion of the liquid in the tridymite primary phase field. INTRODUCTION The conversion process of copper consists of oxidizing Fe and S present in mattes with 60 to 65wt% Cu (up to 16wt% Fe). This process is separated into two stages: 1- Slag blowing: Fe is oxidized, the addition of a flux such as SiO2 (silica) forms a second liquid phase called slag, this phase is removed from the furnace; 2-Copper blowing: in this stage, the matte with low concentration of Fe (<1% w/w) is again oxidized to remove S as SO2 in the exhaust gases. The product of these two processes is the formation of Copper Blister (> 98wt% Cu) (Schlesinger et al., 2011). Unlike the aforementioned conventional processes, in most Chilean smelters, conversion Peirce- Smith Furnaces are loaded with high copper matte (70–75wt% Cu) (Henao & Moyano, 2016). Due to the low concentration of iron in these matte (up to 5wt%), it is considered that separating the conversion process in two stages is neither operational nor environmentally convenient. Therefore, the process is carried out in a single stage (Pradena et al., 2006), generating a slag phase with a high percentage of Cu2O (wt%Cu>40).

Jan 1, 2019

By E. Watkins, V. Gangrade, P. Zhang, J. Addis, D. W. H. Su, T. Minoski, C. Hollerich, M. Van Dyke, S. Schatzel, H. Dougherty

"This paper presents the results of a comprehensive study conducted by the Centers for Disease Control (CDC), National Institute for Occupational Safety and Health (NIOSH), Pittsburgh Mining Research Division (PMRD) to evaluate the effects of longwall-induced subsurface deformations and permeability changes on shale gas well integrity and safety under shallow cover. NIOSH researchers selected a study site over a southwestern Pennsylvania coal mine, which extracts 1,500-ft-wide longwall faces under 482 feet of cover. One in-place inclinometer well and three permeability monitoring wells were drilled and installed over a 125-ft by 275-ft centers abutment pillar. In addition to the inclinometer well and monitoring wells, surface subsidence measurements and underground coal pillar pressure measurements were conducted as the first 1,500-ft-wide longwall panel on the south side of the abutment pillar mined by the site.A number of FLAC3D finite difference simulations (Itasca Consulting, 2017) were conducted to estimate surface subsidence, coal pillar pressure increases, and horizontal displacements in the in-place inclinometer (IPI) monitoring well. Comparisons of the FLAC3D finite difference simulation results and the surface, subsurface, and underground instrumentation results show that the measured IPI casing deformations are in reasonable agreement with those predicted by the FLAC3D models, and that the measured surface subsidence and underground pillar pressure are in excellent agreement with those predicted by the 3D models. Measured permeability changes were incorporated into a preliminary calculation to evaluate the effect of a hypothetical shale gas well leak on longwall ventilation. Results from this 2018 research clearly indicate that under shallow cover, the measured horizontal displacements within the abutment pillar are at least one order of magnitude higher than those measured in a 2017 study under deep cover and slightly higher than those measured in a 2014 study under medium cover. This research represents a very important step and initiative in utilizing the knowledge and science obtained from mining research to improve miner and public safety as well as the safety and health of the workers in the oil and gas industries"

Jan 1, 2019

By Paul E. Mather, Matthew J. M. Krane

Anode or fire refining is the final pyrometallurgical step in the production of copper anode. Part of this process purifies liquid copper by reducing its dissolved oxygen with a natural gas-steam mixture. Until now there have been no transient models of this process coupling the injected gas jet mass transport with its chemical reactions. A transient, 1D flow, chemical reaction model was made to estimate the time-dependent behavior of anode copper composition, soot formation, and the transient gas jet composition along its height. Model estimates were made for reduction rate, soot emission rate, and exergy loss and destruction distributions for two melt temperatures and a range of steam addition rates. It was found that increases to melt temperature and steam addition rate increased reduction rate and decreased soot emission, while having little effect on exergetic performance. Estimates for reduction histories were compared to industrial data. INTRODUCTION Anode/fire refining is the final pyrometallurgical step in the production of copper anodes; it is essential for removing dissolved gases which cause porosity in cast anodes. Despite its significance, the open literature appears devoid of any transient models of the entire process; furthermore, there are very little published process data with which to validate any models made. This dual dearth of modelling work and process data inhibits studies of the tradeoffs between process and performance changes, desirable for decreasing reduction time and soot formation as well as quantifying changes in the exergy losses and destructions of the process. This work introduces a reduced-order, transient model of reduction during fire refining, examines performance trends with operating conditions, and compares model estimates with industrial data. Overview of anode refining The purpose of anode refining is to produce liquid copper which can be cast with minimal gas porosity, which disrupts the downstream electrorefining process. Dissolved sulfur is removed first, then oxygen, by reactions with different injected gases. The removal of oxygen (the reduction step) is the subject of this proceeding and is effected by the bubbling of natural gas, typically mixed with steam, through the melt from tuyeres. A typical refining run reduces dissolved oxygen from 3000 ppm to 300 ppm in 2–3 hours (Schlesinger, King, Sole, & Davenport, 2011). The refined copper is then cast as anodes. Figure 1 shows a schematic of the furnace vessel.

Jan 1, 2019

By Damian Connelly

The metallurgical heart of the majority of copper oxide processes is the heap leaching operation. Fresh low grade sulfide ores is a far greater challenge.The success of this unit operation is so important that operators need to understand the ramifications of their decisions or non-decisions and how they could affect the downstream processing. Heap leaching is an operation that can be described as a scientific art whereby principles of science can be used to guide experienced personnel in attaining their goals. Recent advances have been made based on better understanding the ore characteristics. The success of a heap leach operation, or otherwise, is dependent upon a number of factors, notably: The type of ore to be treated The extent of testwork completed to define the process The interpretation of the testwork results Ore preparation prior to stacking Agglomeration and curing requirements Other issues are: Compliance with the ’smaller’ requirements of environmental authorities Adequate and timely drainage of solution from the base of a leaching lift The degree of saturation in the pads Heap porosity – coarser or finer ore, which is better? Higher or lower irrigation rates – which would produce a better result? Laying out irrigation pipework for ease of operation and maintenance The addition of water, raffinate during agglomeration where needed The heap leaching of sulfide ores, including chalcopyrite, via enhanced bacterial leaching is discussed. INTRODUCTION Over the last twenty years, production of extremely pure copper from solvent extraction and electrowinning (SX/EW) has become more common in a market of real declining prices for copper metal. This paper touches on a number of heap leach operations and experiences. These projects were subjected to extensive engineering design and resulted in low capital cost, efficient operations with a number of lessons learned. The key to these operations was the performance of the heaps and associated fluid collection systems rather than the plants themselves.

Jan 1, 2019

By B. R. Maas

Processing material at a consistent rate through the continuous countercurrent decantation (CCD) thickeners presented a major bottle neck to unlocking additional value from one of the post-flotation streams at the Kansanshi processing plant. The manual operation of the thickeners making up the CCD train resulted in frequent imbalances and process upsets across units. The automation of CCD trains is notoriously tricky as the available manipulated variables are outnumbered by the parameters requiring regulation. The implementation of an advanced, auction-based, control philosophy to manage the movement of both slurry and solution inventory through the train addressed this parameter imbalance and lead to the stabilisation of the circuit. Since the commissioning of this control strategy: an additional 7 200 dmt/day (+36% throughput) of material can reliably be processed through the train, the number of monthly downtime events has reduced, and a saving of $354 000/month in reagent cost has been achieved. INTRODUCTION CCD operation Agitated leaching is a common method used in hydrometallurgy to extract a metal from its host ore. The host ore is initially finely ground to liberate the surfaces of the valued minerals and improve the kinetics of the leaching process. The ore is then contacted in an agitated tank with a lixiviant to dissolve the desired metal into the aqueous phase. The resultant slurry from the leaching process comprises of a solution pregnant in the metal salt and a barren ore. The first purification step taken after leaching is to wash the pregnant liquor solution (PLS) from the depleted ore. On the industrial scale, a set of between two to ten thickeners arranged in a countercurrent configuration is often used to carry out this separation (Perry & Chilton, 1973). The slurry is introduced at the head of the train and a wash solution at the tail. The two streams are pumped through each thickener countercurrent to one other. At each stage the residual PLS in the slurry is mixed and diluted down with the countercurrent overflow solution from the downstream thickener. The diluted slurry is fed into the thickener where the solids separate out through gravity sedimentation. The settled solids are channelled towards the underflow of the thickener by a rake mechanism and pumped downstream to the next thickener in the train. The outcome is the recovery of a PLS from the overflow of the lead thickener and a slurry of washed solids from the underflow of the tails thickener.

Jan 1, 2019

By M. G. Beukes

"In South Africa most of the large gold mines operate between 1500m and 4500m below surface where reef is accessed initially through a vertical shaft system then via a network of tunnels and mined in either a longwall, sequential grid or scattered mining configuration. Due to the complexity of the ventilation networks used to ventilate these mines and the potential disastrous consequences associated with underground fires, it is of utmost importance that these mines are managed in such a way that underground fires are prevented. However, if they do occur the fires are managed to firstly prevent the loss of life and secondly protect the infrastructure and viability of the mine. The aim of this paper will be to: • Discuss current SA mining legislation regarding underground fire prevention and control. • Examine these fires from a risk management perspective by means of a bowtie assessment. • List and discuss the major Threats and Consequences as determined by the bowtie assessment. • Discuss the various prevention and consequence controls for deep level underground fires. • Examine how to effectively run an emergency control room. From this, a practical way of designing, implementing and managing an underground fire management system is explored. Lastly, the paper identifies new technology and ways of thinking and how these can be used to combat underground fires. INTRODUCTION The orebodies of South African gold mines are generally narrow tabular structures that vary in thickness between 0.8m and 1.2m with an inclination of between 200 and 700. This, coupled with depths of between 1500m and 4500m, as well as the unpredictable geology, creates unique challenges and significantly impacts on mine designs and mining methods. In general, gold bearing reefs are accessed initially through a vertical shaft system then via a network of tunnels and mined in either a longwall, sequential grid or scattered mining configuration (Figure 1). Mining is very labour intensive with very limited mechanisation opportunities and this increases the risk to human life if an underground fire occurs. On 16 September 1986, one of the worst mining disasters in SA mining history took place when 177 mineworkers were killed at Kinross Mine. An acetylene tank sparked flames that swept through the mining tunnel igniting plastic covering on the wiring and the flames also set fire to polyurethane foam. The burning plastic combined with polyurethane and the toxic fumes that filled the shafts caused the miners death. This incident was a stark reminder of the serious consequence that underground fires can have on human life as well as the crippling financial and asset impact for the mining companies. Over the past thirty years, the SA mining industry reduced the number of mine fires significantly by replacing normal timber support with fire retardant treated timber, alternative support systems such as backfill and elongate support and many other fire prevention initiatives. Although the number of fire incidents and number of fatalities due to fires does not show a direct correlation because of various factors, the controls put in place against fires has had an impact on the number of fire and explosion fatalities (Figure 2)."

Jan 1, 2019

By R. Bishop, J. Baggett, J. Monsalve, J. Hole, N. Ripepi, A. Abassi

This work focuses on the operational and safety issues associated with karst voids in large opening underground mines. Issues include water inrush, structural instability, and engineering uncertainty in these environments. Coupled with the fracturing prevalent in folded sedimentary rocks, karsts are complex and challenging ground control risks. Traditional methods of predicting karst locations, such as probe drilling, are impeded by the inconsistent spatial distribution and variable sizes of the features. Ground penetrating radar (GPR) is a geophysical technique that transmits radio waves into a medium and subsequently detects reflected waves via a receiver. The travel time and energy of received signals are then processed and interpreted. The difference in material properties between limestone and open karsts causes strong reflections. GPR is frequently used as a geophysical surveying technique in several industries, however there is a lack of published research on underground mining GPR applications. The purpose of this work is to prove the viability of GPR in underground stone mines for karst detection, and to discuss the importance of karst detection ahead of mining. INTRODUCTION The Mine Safety and Health Administration (MSHA) currently lists 116 active underground stone mines in the United States, the vast majority of which extract limestone for crushed stone products. These limestone mines have the potential to encounter karst voids at some point in their operation, as most karstic regions of the United States develop in limestone rock masses (Kuniansky, Weary, & Kaufmann, 2016). Karsts, the cavities formed by the dissolution of carbonate rock, have long plagued the mining and tunneling industries, as well as been a hindrance on the Earth’s surface, producing sinkholes and ruining otherwise valuable land for construction and public use. The impact of karsts on the Gavarres tunnel in Spain is well documented by Alija et al; constant instability conditions, material spills into the tunnel, and unexpected cavities seriously delayed the project deadlines and “were not foreseen in the design” (Alija, Torrijo, & Qunita-Ferreira, 2013). At the water supply project in Sohngua River, China, Bin et al detail the presence of both water and sediment filled karsts which are sources of disastrous conditions at this tunnel (Bin, et al., 2017). A hydrological tunnel in Lebanon encountered numerous massive karsts in the tunneling path which required remediation via friction anchors, rockbolts, welded wire fabric, channel steel arch segments, invert steel beams, and shotcrete (Leech, Jaoude, & Ghanem, 2008). From a design standpoint, rock mass classification schemes, such as the RMR from Bieniawski and the Q-system from Barton, are not able to represent the true nature of a karstified carbonate rock mass, and therefore complex case-by-case analyses of underground conditions are necessary (Andriani & Parise, 2017).

Jan 1, 2019

By Beatrice Pierre, Juan Carrasco

Altonorte began as a concentrate roasting operation in 1988 under the name of Refimet. In 1993, a copper smelter was built with a design capacity of 203,000 tonnes per annum of concentrate. Since 2001, many technological advances have been made in Altonorte, where the biggest Noranda Reactor in the world is installed being the first Noranda Reactor reaching above one million tonnes of copper concentrates processed per annum. In 2013, Altonorte was acquired by Glencore. Recently due to various new environmental regulations in Chile, Altonorte has evolved to new standards of operation in order to reach the vision of becoming a World Class Smelter. This paper describes the path followed to improve safety, environmental performance, process capacity, reliability, and productivity. The foundation for the growth and success in Altonorte is our People. Employee engagement and branding of our cultural journey is what allows Altonorte to face the future with the certainty of becoming a World Class Smelter. INTRODUCTION Altonorte is located in Antofagasta, the mining capital in the north of Chile and is the last smelter built in Chile practically completed with second hand equipment. The biggest technological change in Altonorte occurred during the phase 3 expansion in 2003, where the old Reverberatory furnace was shut down and replaced by the biggest Noranda Reactor installed in the world. The vessel measures 5.3 m × 26m. ºAdditionally, this project contemplated a new rotary dryer, three (3) new Peirce Smith converters, new anode furnaces and a new Acid plant. The nominal capacity was to treat 816.000 tons of new concentrate per year. In 2008, a new expansion phase was implemented where a new double absorption acid plant replaced the oldest acid plant. Bottlenecks such as blowing capacity and oxygen availability were solved installing a new air blower and a new contract was negotiated with our oxygen supplier to increase oxygen availability up to 683 tpd. This improvement defined the current nominal capacity of 1.100.000 ton of new concentrate per year. Current process description All concentrates are received by trucks directly from domestic mines or from the Antofagasta international port in cases of imported concentrates; the concentrate warehouse has a capacity of 25 kt where the blend is prepared to feed the smelter.

Jan 1, 2019

By C. Opoku-Ware, M. Kukay, P. Conrad, F. Inkoom, R. Pal

Researchers at Montana Tech are investigating the potential for developing trees tolerable to degraded un-reclaimed mine site tailings and soils as a solution to re-establishing long-term tree growth on those sites. This project involves growing tree seedlings from seeds planted in the degraded mine tailings and soils in which they will eventually be planted. The outcome of the project is expected to lead to a successful solution for re-establishing tree growth in degraded tailings and soils in Butte, Montana with minimal post-planting human intervention. Work conducted on the project to date has shown successful growth of seedlings in degraded tailings and soils. INTRODUCTION In an effort to improve Butte Area One natural resources, this research project is working to help restore tree growth in the Butte Priority Soils Operable Unit Boundary (BPSOU) (Opoku-Ware, et al 2018). Research by Blicker, et al (2003) found that, the BPSOU, which is part of the Silver Bow Creek/Butte Area National Priorities List (Superfund) Site within and near Butte, Montana has multiple historic mining sites situated entirely within the urban setting of Butte. Mine wastes and mill tailings, accumulated from over 100 years of gold, silver, and especially copper mining are dispersed throughout Butte, posing health risks to human and environmental receptors. Stabilization of tailings sites is needed to control fugitive dust, prevent run-off of toxic material resulting in subsequent sediment deposition in streams, reducing the volume of water seepage through acidic and heavy metal contaminated material, and improving land productivity and aesthetic values (Watkin and Watkin, 1982). If successful, the project will help restore water quality and maintain stream flow in Silver Bow Creek where it flows through Butte Area One. Trees native to Butte are being grown to seedlings in a greenhouse located on Montana Tech’s campus which will be planted in degraded soils located within the BPSOU. Growing trees is expected to help restore vegetative ground cover within the watershed contributing to stream flow in Silver Bow Creek. The trees will prevent soil and tailings from eroding and being deposited in Silver Bow Creek where they could degrade water quality and choke stream flow. The project combines research with tree seedling growth to provide a resource for Butte that could produce thousands of tree seedlings each year adapted to the harsh climate, soil, and tailings conditions that exist in the BPSOU where they will grow. It is anticipated that the trees developed by the project will have the capability for long-term survival and growth because they will be germinated and grown into seedlings in the degraded soils and tailings collected from the BPSOU where they will be planted. Soils and tailings collected for the project have been evaluated to determine if they lack nutrients or contain substances potentially toxic to the long-term growth and survival of the trees. Toxic levels of metals, high concentrations of soluble salts, extremes in pH, nutrient deficiencies and imbalances, surface crusting, high bulk density, low infiltration rates, high surface temperatures, low cation exchange capacity, restricted microbial activity, low water retention, harsh climatic conditions and surface particle movement are some of the traits of mine tailings sites that restrict revegetation efforts (Barth, 1986).

Jan 1, 2019

By C. Hudson, D. Tremblay, A. Frey

"A discussion of the design, challenges and successes associated with the commissioning of the gravity recovery circuit at Canada’s newest open pit gold mine - Atlantic Gold’s Moose River Consolidated Project in Nova Scotia, Canada is presented. An overview of the project, its historical significance and overall flowsheet is provided with special focus given to the design and selection of the gravity circuit equipment including the scalping screen, gravity concentrators and the novel intensive leaching technology selected for the project. The performance of the gravity circuit is benchmarked against the feasibility study process design specifications and the outcomes are discussed. Challenges encountered during commissioning are also presented, including the use of third-party automation and the effects of screen sizing on overall gravity circuit performance. Mechanical modifications made to the Sepro Leach Reactor for the Moose River project are also discussed. A detailed technical review of the mechanical and operational aspects of the Sepro Leach Reactor is provided with key operational data on leach times, recoveries, reagent usage, solid-liquid separation, pregnant solution quality and its influence on bullion purity.INTRODUCTION Atlantic Gold Corporation’s Moose River Touquoy Mill in Nova Scotia, Canada was commissioned in the fourth quarter of 2017 with commercial production declared in March of 2018. The 2 Mtpa process plant uses a conventional, gravity-CIL process. This site was previously mined in the 1870s. Interest waned in the early 1900s but resumed in the 1930s and the mine was brought back into production in 1935 until an underground mine collapse in 1936. This mining district became famous after CRBC radio commenced a ground breaking, around the clock, broadcast of the rescue operations. Over 100 million people listened to the broadcast from Canada, the United States and the United Kingdom. These broadcasts changed radio, transforming it from a medium for music to on the spot, breaking news reporting. The mill was constructed by Ausenco on a fixed price EPC contract in the historic Moose River gold mining district, 95 km north-east of Halifax by road. The mill will process ore from the adjacent Touquoy pit for the first 5+ years of operation; after the Touquoy reserves are exhausted, the mill will process ore trucked 37 km from the Beaver Dam deposit for an additional 5 years."

Jan 1, 2019

By Gregory M. Rumbaugh, Christopher Mark

"The proliferation of unconventional gas well development in the Northern Appalachian coalfields has raised a number of mine safety concerns. Unconventional wells, which extract gas from deep shale formations, are characterized by gas volumes and pressures that are significantly higher than those observed at many conventional wells. The gas is composed largely of methane as well as other hydrocarbons. Hundreds of planned and actively producing wells penetrate protective coal pillars or barriers within active mine boundaries, including chain pillars located between longwall panels. Gas released from a well damaged by mining-induced ground movements could pose a risk to miners by flowing into the mine atmosphere. The mining-induced ground movements that may cause well damage include conventional subsidence, non-conventional subsidence (e.g., bedding plane slip), pillar failure, and floor instability. This paper describes the known risk factors for each of the four failure mechanisms. It includes a framework that can guide the risk assessment process when mining takes place near gas or oil wells.INTRODUCTIONSouthwestern Pennsylvania has served for centuries as a producer of coal, oil, and natural gas. Coal mines were first developed in the Pittsburgh Coal Seam in the 1760s, with the first recorded mine in 1761 being the Fort Pitt Mine (Edmunds, 2002). Natural gas was introduced to the region when the Haymaker Well in Murrysville, Pennsylvania experienced a blowout on November 3, 1878. Although it was originally drilled prospecting for oil, it produced an estimated 30 million cubic feet per day of natural gas. Without well controls or pipeline infrastructure in place, it burst into flames and lit the night sky for over a year. Soon after, the Penn Fuel Company continued development of the Murrysville gas field and is credited with making Pittsburgh, Pennsylvania the first major city in the U.S. to have natural gas supplied for home and industrial uses. “Natural gas is king in Pittsburgh,” proclaimed an October 18, 1885, article in the New York Times headlined “Value of Natural Gas, Its Use Clarifies the Atmosphere at Pittsburgh” (AOGHS, 2018). By the early 1900s, coal, oil, and natural gas production had reached the southern extents of Pennsylvania in Greene County. The county had first produced oil in 1886, and shortly after began producing natural gas in 1890. By 1906, over 1,300 wells had been drilled (Stone and Clapp, 1906)."

Jan 1, 2019

By E. Stone, R. Reagan

Risk of hand injury is very real for operators carrying out conventional bolting operations with power torque tools, reaction arms and backup wrenches. Bolting operations of this type are common today in the installation and maintenance of heavy mining machinery and equipment. Newer solutions have become available that have the potential to dramatically reduce the risk of hand injuries in mining applications. MINING APPLICATIONS Within the scope of mining operations, various types of equipment are used such as tunnel boring machines, bucket wheel excavators, draglines, material handlers, screens, pumps, crushers, continuous miners and longwall systems. Design of these machines typically includes larger diameter bolts for strength and durability. Due to rugged use all machines require frequent maintenance and service which requires the use of heavy industrial bolting tools and methods. Those engaged in bolting operations include technicians working for end-users, equipment manufacturers, general contractors and others who provide services in mining operations. Most all personnel involved with these activities are engaged with use of high power bolting tools and procedures. Training is essential to raise the awareness of bolting safety and to avoid accidents. However improved bolting tools and procedures can play an even more significant role in further improving the safety of all those engaged with bolting in the mining industry. SAFETY CONCERNS Professionals working in the mining industry are constantly looking for ways to further reduce risk to health and safety. Bolting operations which are fundamental to service and maintenance of mining equipment are often overlooked as a potential area for improvement. Several areas of bolting operations offer potential for improvement in safety and avoiding accidents during equipment maintenance. This paper addresses the safety concerns associated with reaction arms and backup wrenches in conventional bolting applications (Figure 1).

Jan 1, 2019

By A. A. Wessels, D. P. Allison

"Mine hoists are built to handle a certain nameplate capacity; they are specified and designed according to the required duty. However, as production capacity increases in other parts of an operation, the hoist capacity can become the critical constraint. Such a situation occurred at Lundin Mining’s Neves-Corvo operation. This paper examines how each component of the existing hoisting system was examined and optimized. Through a combination of engineering study and hoist simulations, the annual hoisting capacity was improved by 24% through increases in payload capacity and available hoisting time combined with a reduction in cycle time, while no changes were made to the hoist motor, drum or headframe. The additional payload capacity was achieved by reducing the mass of the hoist ropes and skips, and improving load monitoring systems. The cycle time was reduced through the shortening of the creep distances and increased availability through the installation of a shaft collar safety platform, alternative guide rope bushes, and superior liners for both the skips and underground measuring flasks. Enhanced cooling of the hoist electrical system was also incorporated to increase hoist availability by reducing downtime during hot summer months. The changes will increase the capacity from the current 4.5 mega tonnes per annum (Mtpa) to a planned 5.6 Mtpa and are being implemented over a 2-year period whilst maintaining the mine production during the upgrade work. INTRODUCTION Neves-Corvo Mine Neves-Corvo is primarily a copper and zinc mine producing copper, zinc and lead concentrates. The operation is owned and operated by Somincor, the Portuguese subsidiary of Lundin Mining. Located in the Alentejo district of southern Portugal, the operation is situated approximately 15 km southeast of the town of Castro Verde, where summer temperatures can reach as high as 45ºC, and approximately 220 km southeast of Lisbon. The principal means of mine access is via a ramp from surface, with the vertical shaft used to hoist ore and waste from the 700 m level, while conveyors descend from the 700 m level to transport ore and waste up from the deeper levels of the mine. The mine is highly mechanized and several different stoping methods are employed, with the most significant being bench-and-fill and drift-and-fill. The Neves-Corvo mine currently exploits five orebodies: Neves, Corvo, Graça, Zambujal and Lombador for copper and zinc-lead ores which are processed in one of two plants. All the orebodies are currently exploited over their full elevation with the exception of Lombador which is only mined down to the 220 m level, approximately the top 50% of the orebody, known as Lombador Phase 1."

Jan 1, 2019