Search Documents

By F. Rosenblum

An on-stream particle size analyzer (PSA) based on the sedimentation principle has been developed to the commercial prototype stage and tested at a concentrator. The current instrument gives a direct reading of the weight % finer than any two sizes, although the capability exists for providing a complete size distribution through the sieve and sub-sieve range. The readings obtained at intervals of about 10 minutes are derived from 0.5-L samples of slurry cut from the monitored stream. The accuracy of the PSA meets the requirements of process control.

Jan 1, 1984

By M. Falutsu

"The PSI-200 is a rugged, innovative, and easy to install on-stream size analyzer. Its calibration is simple and can be done on-line, during operation. Two measurements are displayed on the panel, which are expressed as percent passing a selected size, or as any statistical diameter. These two measurements are given as two continuous 4-20 mA output signals. Operation alarms are displayed on the screen or are given as digital output signals.The PSI-200 has been used in various applications at Lakefield Research. Particle sizes ranging from 10 µm to 450 µm have been monitored successfully, with an accuracy of 1- 2%. Having the size measured continuously and reliably, optimum conditions have been established for the grinding circuit, resulting in a superior quality in pilot plant testing.INTRODUCTIONThe challenge of any operating plant is to optimize product quality, maximize throughput and minimize operating costs. The importance of particle size measurement at a grinding circuit is well recognized. Monitoring continuously the particle size and keeping the product as uniform as possible is crucial to the whole mill operation regardless of the nature of the operation.Various techniques and instruments have been developed over the years attempting to give reliable on-line size analysis data. The operating difficulties and the reliability of these equipment still present major drawbacks and none of them proved to be widely accepted.PSI-200 is a relatively new on-line analyzer. The operation is simple and of low cost and the maintenance required minimal. It measures particle size and it displays two parameters of the solids size distribution, either weight fraction of passing a certain size or any statistical diameter. Two analog outputs can be sent to a process control system and through a supervisory control loop the correct action can be taken to maintain the desired particle size (perhaps adjust the feed rate to the grinding mill)."

Jan 1, 1993

A New Online Detection Method for Arsenic Minerals in Process Streams

Sep 13, 2010

The price of oil and other minerals may not make the costly business of offshore exploration seem -attractive at present. There is little doubt that the future search for the strategic resources will tend towards deeper waters particularly on the continental slope margins. In addition with the realisation that active tectonic environments (eg the Makassar Straits) cannot be excluded as potential hydrocarbon sources there is an increasing demand by the explorationists for deep water survey capability. Such deep water research has until recently been restricted to a few specialised academic institutions ;however with the anticipated extra, demand from other institutions, companies, and government agencies, Marconi Underwater Systems Limited (MUSL)and the Institute of Oceanographic Sciences in the UK have come together to allow MUSL to provide the deep water mapping system GLORIA on a commercial basis -for the first time. The GLORIA package comprises a deep water(more than 400m) side scan sonar system which, by operating at a frequency around 6.4 kHz can insonify swathes on the seafloor up to 60 km wide. In addition, single channel seismic, 3.5 kHz high resolution profiles, precision echo sounding, magnetic and gravimetric data all combine to provide as complete a regional interpretation as possible. The GLORIA system combines surveying at a reconnaissance level, covering as it does up to 20,000 sq.km per day, with a very high reliability, so that even in- economically unfavourable times, it can-still be considered as an invaluable and cost effective primary exploration tool. Analysis of the GLORIA data enables the identification of areas of particular interest requiring more detailed study by the more costly multi-channel seismics at a later date.

Jan 1, 1987

By Yixian Zhao

Although many ultimate pit limit design algorithms have been developed for the past one- quarter century, only the well known Lerchs-Grossmann's (LG) algorithm is capable of producing a truly optimum ultimate pit limit today. This paper presents a graph theory oriented algorithm for optimum ultimate pit limit design. This algorithm produces a true optimal solution and maximizes the total undiscounted net profit for a given 3-D block mine model. The algorithm performs much better than the well known LG algorithm, in terms of the reduction in computation time and computer memory requirements. More importantly the new algorithm is easier to understand and implement than the LG algorithm. Specifically, this paper discusses: 1) the computer representation of arcs and the rules of arc generations which dictate the formation of trees in the graph, 2) the mechanism of joint support and re-allocation, 3) the properties, the general procedures of the algorithm, and the suggested specific steps to implement the algorithm, 4) comparison between the new algorithm with LG algorithm, and 5) some experience in implementation of the algorithm and two case study results.

Jan 1, 1992

By R. Washnock, P. James

"INTRODUCTION Abstract Tankhouse iron control through application of new treatment technology to mitigate conventional bleeding losses is considered. Implementation is discussed and the treatment economics explored. A representative case is assessed. Treatment benefits and application drivers for specific scenarios are noted. Background Hydrometallurgical ore processing has become a significant metal extraction/production avenue in recent decades. In copper mining; the focus for this examination, around 25% of global primary copper production and nearly 50% of US production result from various hydrothermal leaching extraction approaches coupled to Solvent Extraction/Electrowinning (SX/EW) metal production. Generally such processing is favored over pyrometallurgical processes for lower ore grades and as such is finding growing use and is expected to remain a key processing route looking forward with average world-wide ore grades falling as known ore reserves become exhausted. Target Problem And Motivation In hydrometallurgical processing the production circuit may be thought of as a chain of interlocked recirculation loops (Figure 1). Leaching dissolves the target metal from the ore along with other ore components which contaminate the Pregnant Leach Solution (PLS). Iron is a common component in copper ores and, as a result, occurs fairly ubiquitously in copper Pregnant Leach Solutions (PLS) generated by leaching. Leached components migrate through the production circuit from left to right (Figure 1) through a net combination of chemical and mechanical transport mechanisms. Selectivity at the recirculation loop interfaces tends to retard rejected component migration through the production process. As a result, overall relative contaminant migration fluxes are slower than the target metal (copper) and the contaminants tend to build up relative to copper in the more upstream portions of the processing circuit over time with iron often being a significant contaminant. Further, while copper is continuously removed from the system in appreciable amounts, little contaminant exit occurs and the absolute contaminant amounts and concentrations also increase throughout the EW circuit over time."

Jan 1, 2018

By T. Sterry Hunt

THE Jones Mine (or Johannes Mine, as it was originally called, from a former proprietor), situated near Springfield, in the township of Caernarvon, Berks County, Pennsylvania, has long been known as a large deposit of magnetic iron ore, associated with more or less copper pyrites, and with malachite and chrysocolla. It occurs in a belt of soft schistose rocks which rest upon the Laurentian gneiss of the Welsh Mountain, and to the northward are soon concealed by the unconformably overlying Mesozoic sandstone of the region. These metalliferous strata belong to the Primal slates of Rodgers, which, in many other localities in this region, include similar deposits of iron ores associated with more or less copper, and often accompanied by chloritic and argillaceous schists, and, more rarely, by serpentine and small lenticular masses of crystalline limestone. To this same horizon belong the iron ores of Boyertown, Fritz's Island, and Roudenbusch, near Reading, Wheatfield, Cornwall, and Dillsburg (all of which are found along the northern border of the Mesozoic belt of * By the kind permission of Dr. F. A. Genth, of the University of Pennsylvania, I am now enabled to append to this paper the following hitherto unpublished analyses of the Cornwall ores.

Jan 1, 1876

By Gomi S

A new watersoluble binder for mineral ore pellets has been developed by the sulfonation of bituminous materials. A highly effective binder for iron ore pellet making is obtainable from bituminous materials produced in the high temperature cracking of crude oils. This paper deals with production process and basic properties of this binder as well as new applic- ations in the field of iron ore pelletizing.

Jan 1, 1974

By F. Calizaya

This study summarizes the ventilation requirements for a highly mechanized P.T.Freeport Indonesia's underground mine operation in Irian Jaya, Indonesia. The Deep Ore Zone (DOZ) is a copper-gold deposit being developed underneath the current Intermediate Ore Zone (IOZ) mine. One of company's current plans is to prepare this mine for a steady oreflow of 25,000 tpd by year 2003. This study includes the estimation of airflow requirements for various mining activities, the design of major intakes and returns, the determination of airway resistances and specifications of fan duties. It also includes the results of air pressure/quantity measurements in existing airways and the standards stated by the current Indonesian mining law.

Jan 1, 1998

By David C. Yang

A packed column (or static tube) flotation system is an innovative technology which utilizes a controlled dispersion reagent scheme and a new machine. The unique aspect of the machine is its packed-bed design permitting an unlimited froth bed height with countercurrent water washing for effective processing of fine particles. In operation, the conditioned ore slurry is fed into the middle section of the column where separation processes begin. Air, introduced at the bottom of the packed column, contacts the hydrophobic particles and floats them off continuously as the feed is added, while the gangue sinks to the base of the column. The system functions efficiently because intimate particle-bubble contact is achieved by the packing design which has no moving parts and requires no ancillary air-bubble generator. Other attractive features of the packed column flotation include high throughput, low power requirements, and simple control. Results from laboratory and pilot plant tests of this system show remarkable improvements over current industrial practices on a wide variety of ores and coals.

Jan 1, 1988

By G. Riveros

A new, continuous fire refining process for copper has been developed and tested at the 5 tph pilot scale. During oxidation, the blister copper flows through a packed bed of crushed refractory bricks counter-current to a hot oxygen containing gas. The resulting desulphurized copper flows then directly into a packed bed of charcoal for deoxidation. By controlling the air to natural gas ratio, both temperature and reducing conditions can be controlled. Based on extensive laboratory scale measurements of the rate of copper oxidation and reduction, the process concept was developed aided by process modeling and simulation. The industrial-pilot scale installation built at the ENAMI Paipote smelter in Chile, consists of two cylindrical, compact reactors, operating in line, with a designed capacity of 5 t/h of blister copper. The results of the industrial-pilot tests confirmed the feasibility of the new process. The blister copper processing capacity was increased to 10 t/h with satisfactory sulphur removal. The degree of oxidation as well the copper temperature was controlled with relative ease. The specially designed siphon block allowed for smooth tapping of the oxidized copper and separation of refining slag. The reduction of oxidized copper in the packed bed of charcoal appeared to be very effective while control of the degree of reduction according to the height of the bed ensured control of the oxygen content in the refined copper at the required level.

Jan 1, 2007

By T. Bhambhani, J. Jankolovits

Sphalerite flotation using copper sulfate has been performed in the industry for decades and the mechanism of Cu activation is well established. Despite its ubiquity, many practical questions surrounding copper sulfate persist. It is not clear how iron selectivity is achieved in zinc circuits given the propensity of iron sulfides to be activated by copper. Also, the large variation in copper sulfate dosages across different plants and ore types cannot be explained. Lastly, Zn flotation with greatly reduced copper sulfate dosages attracts significant interest and has been demonstrated in certain laboratory settings, but no information is available on why those laboratory solutions have not been adopted in plant practice. Flotation studies are presented that demonstrate that Zn flotation with very low copper sulfate dosages is possible when using certain novel collectors that are not practised in the industry. However, these reagent schemes are impractical because of a heretofore unappreciated and critical role that copper sulfate plays in Fe rejection. With both very low and standard copper sulfate dosages, copper sulfate influences both Zn flotation and Fe rejection. The results highlight the multifaceted role of copper sulfate in zinc flotation and the need to holistically consider complex systems’ behaviour to understand flotation reagent mechanisms and optimise plant performance. Keywords: Sphalerite flotation, metal activation, copper sulfate, iron rejection

Jan 1, 2020

By Van Groenou B

Traditionally mining and conservation have been regarded as opposing and mutually exclusive concepts of land use. Often problems are anticipated which cannot be substantiated by facts. In addition, an ill defined time-scale adds to potentially emotive issues. Examples from Australia and elsewhere are presented which illustrate the dynamic nature of the environment and accentuate sequence patterns in plant community development following natural and man-made disturbances. The mining industry generally appears to be aware of the environmental impact of mining and whilst endeavouring to minimise the disturbance, is still orientated towards maximum production.

Jan 1, 1984

By P. Somasundaran

While sustainability itself needs to be redefined in a selfless way, methods of measuring and optimizing it also need to be reformulated. Gone are the days when we had the luxury of abundant resources and the freedom to extract values in self-centered ways. In the past, focus has been mostly on reagent performance, processing operations, and upgrading of tools to maximize rather than optimize value extraction from the earth's crust. Today we as extractors face a new set of challenges that include value separation from low quality resources including wastes, but within the energy, environment, and societal constraints. Development of such technology depends on understanding the role of entities and concepts such as bio-molecular interactions at surfaces, forces involved in inter-granular versus intra-granular fracture in new fragmentation methods, robotic in-situ or extraterrestrial mining, exploiting new membrane and nano technology, use of new sensors and actuators for detection and separation and computation capabilities for faster and economical processing. Equally importantly, we need to communicate with everyone what we foresee and anticipate when we extrapolate the type-performance-cost relationship of ores to the era ahead of us and establish viable schemes for ecological survival. Keywords: sustainable mineral extraction

Sep 1, 2012

By N. Schreithofer, M. Aspiala, R. Serna

The novel attachment timer apparatus presented in this paper serves as a diagnostic tool that allows the detection of changes in bubble-particle attachment probability and therefore floatability caused by alterations in the chemical environment and particle properties. The apparatus consists of six identical capillaries where bubbles with defined size are produced simultaneously in a measurement chamber. The bubbles at the capillary tips are placed in contact with the submerged particle bed for specific time periods, controlled with the help of automatic actuators. The advantage of the instrument is that hundreds of bubble-particle contacts can be measured automatically within a short time period. Microscopic pictures of each measured bubble are taken while recording the movement of the bubble before, during and after contact with the solid particles. The recorded pictures can be used to determine the actual bubble size and its corresponding deviation, and to detect the attachment of particles. The attached particles are collected in a detachable chamber for subsequent characterization. Furthermore, the device is portable and can be taken to the mineral processing plants for quick evaluation of particle-bubble attachment efficiency with particles and process water sampled directly from real processes.

Jan 1, 2017

By Virgil L. Barr

National income originating compared to physical production for an enterprise or an industry reflects its ability to strengthen the national economy. For a single industrial sector or for an industry this comparison can be useful to reflect changes that may occur in this ability to contribute because of changing supply-demand-income-investment equilibria. A favorable relationship can be postulated by specified economic incentive, and the accompanying technologic input required can be shown. The new index proposes the use of the Federal Reserve Board indexes of production divided by the constant dollar income originating in the petroleum industry which reflects increases or decreases in performance. When compared with other mineral industries and with, total industry, an approximation of relative strength is evident. By constructing three different hypothetical conditions for future petroleum imports, assuming a constant excess capacity requirement for domestic production, and providing an estimate for future domestic demand for petroleum, the impact on the performance index can be shown. Thus, a strong position for the petroleum and natural gas industry can be stated. If this is done, it becomes evident that because of restrictions on cost-price relationships, a drilling program that would provide enough domestic oil to meet demand may not be practicable. By difference, the amount of improvement in methods of production and processing through technologic advancements can be stated explicitly.

Jan 1, 1960

By A. J. Nugent

Investigations were undertaken to evaluate peroxygen compounds for effective­ness in alkaline cyanide leaching of gold. The addition of peroxygens improved the leach results. Calcium peroxide was the best performed reagent to be employed. Improved reagent consumption followed the trend of calcium peroxide> hydrogen peroxide> no peroxygen addition. In general, preaeration stages could be eliminated, and improved leach rates achieved with no detrimental impact on leach perfor­mance. Interox has not developed an Au Plus (Trade Mark pending) system to utilise this new leach reagent. Initial plant trials are verifying its potential to give additional benefits.

Jan 1, 1990

By BHAMIDIPATI S. SASTRY, ANMAYA NAIK, ASIF AHMAD, Srivatsan Jayaraman Sridharan, ADITYA PANDEY

Wet kata cooling power (WKCP) as measured by a kata thermometer is a well-known heat stress index used in the mining industry. Although, over the years, several researchers proposed different heat indices and indicated limitations of the kata thermometer, WKCP is used in the South African gold mining industry due to its simplicity and rapidity of assessment. This paper presents a comparative analysis of the newly developed empirical expression for the WKCP and some of the more commonly used empirical models. For this purpose, WKCP measurements are obtained based on experiments conducted in a low-speed wind tunnel. Based on a regression technique, the analysis presented aims to assess the disagreement between the empirical model predictions and actual measurements. The correlation is also presented between WKCP and the well-established thermoregulation models using parameters from the low-speed wind tunnel experiments, including dry-bulb temperature (Td), wet-bulb temperature (Tw), barometric pressure (P), and wind speed (v). It is found that the proposed empirical model for the WKCP represents the bioclimatic interaction quite well under the specific parameters that defines the harsh thermal environment and air condition, such as metabolic activity, clothing of the person, and the velocity of the ventilating air in which the person is working. The statistical analyses performed show that the empirical model proposed for the WKCP produces satisfactory estimates of the thermal stress experienced under lower air velocities, light clothing, and higher metabolic activity rates.

Sep 2, 2021

By BHAMIDIPATI S. SASTRY, SRIVATSAN J. SRIDHARAN, ANMAYA NAIK, ASIF AHMAD, ADITYA PANDEY

Wet kata cooling power (WKCP) measured using a kata thermometer is a well-known heat stress index in mining industries. Although over the years several researchers have proposed different heat indices and indicated the limitations of the kata thermometer, it is still being used in many areas, especially in the South African gold mining industry, mainly because of its simplicity and rapidity of assessment. This paper presents a comparative analysis of the newly developed empirical expression for WKCP, and some of the more prevalent empirical expressions. The analysis presented based on a regression technique aims to assess the disagreement between model predictions and actual measurements. It is found that the WKCP expresses bioclimatic interaction quite well under the specific parameter of interaction that explains the harsh thermal environment and air condition, such as metabolic activity, the person’s clothing, and the velocity of the air in which the person is working. The statistical analysis shows that the WKCP exhibits significant estimates to thermal stress under lower air velocities, light clothing, and higher metabolic activity rates.

By P. K. Kaiser, S. Maloney, S. Yazici

"This paper focusses on the strength or capacity of cable bolts and introduces a new perspective for cable bolt design by demonstrating that mining-induced stress changes may affect cables in a detrimental manner. The concept underlying a novel cable bolt pull-out resistanceor bond capacity model is described and its practical significance is demonstrated by application to a simple two dimensional scenario of a fall-of-ground.A number of practical implications emerging from the application of this model are discussed to provide guidance to ground control personnel jar improving cable bolt support systems in mining applications. These include cable layout optimization, use of cable pre-reinforcements, assessment of embedment length requirements, need for plated cables (or straps), use of bird-caged cables (or buttons), and grout quality issues.IntroductionDuring the last decade, cable bolting has become a standard support technique in mining for handling wide spans, reinforcing are passes, preventing or reducing dilution of ore in marginally stable stopes, and for many other rock support need s.In its infancy, many deficiencies in cable bolt supports resulted from improper installation techniques and, in particular, grout quality control problems and the use of empty breather tubes (Goris, 1990). The development of special grout pumps and fail proof placement procedures (Oliver, 1992; Bourchier and O'Flaherty, 1992) have eliminated many of these early problems. Nevertheless, there are still situations where cables seem to lose their capacity during mining, and in these cases the cables do not provide the expected and needed ground support. In some instances, cables perform extremely well, whereas in others the same support layout and quality of support installation seem to be insufficient, allowing falls-of-ground or progressive cavings to occur."

Jan 1, 1992