Search Documents

By Geoffrey S. Plumlee

The Summitville gold mine, located in southwestern Colorado, received tremendous publicity in the 1980's and 1990's for leaks of cyanide solutions from its heap leach facility. As is typical with cyanide spills, real time, geochemically rigorous assessments of the environmental effects were not performed. Past United States Geological Survey (USGS) research used simple mixing experiments to model the influx of alkaline cyanide heap leach solutions from Summitville into a nearby stream, whose waters were highly acidic due to severe acid-rock drainage (ARD) from the mine. These experiments indicated WAD cyanide rapidly degraded due to formation of Fe-Cu-CN solids and lesser HCN volatilization. The alkaline heap leach solutions also precipitated hydrous iron-and aluminum, oxides and hydroxysulfates (iron and aluminum 'supplied by the acid. rock drainage (ARD]), which then sorbed copper and other heavy metals from the ARD. These results indicate that mixing of cyanide heap leach solutions with ARD may be a cost-effective remedial method at mine sites where treatment of both is required. New experiments are currently in progress to further refine a potential remedial process.

Jan 1, 1998

By Osarnu Inoue

In Mitsubishi Continuous Copper Smelting and Converting Process, smelting, slag-matte separation and matte converting are continuously carried out in series in three furnaces connected by launders. As a result of this operational configuration of the furnaces, influence of the change in operating condition in upper stream, such as variation of feeds in the smelting furnace, propagates to down stream with some delay. In order to achieve stabler operation, process control algorithm based on the dynamic characteristics of each furnace would be very effective. In this study, the dynamic process simulation model was developed for the smelting furnace. The model consists of two mathematical modules, i.e. the thermodynamic module and the mixing module. The calculation results using operating data obtained at Naoshima Smelter showed good agreement with the actually observed change in temperature, composition and flow rate of matte and slag at the outlet of the furnace. In addition, operation parameters such as reaction efficiency of oxygen and coal, dead volume of melts were estimated.

Jan 1, 1999

By Kliment Y. Hakobyan

A new technology for treating molybdenum sulfide concentrates has been developed. It includes roasting the concentrate in a special regime with water vapor, cooling and neutralizing exit gas, oxidation roasting of rhenium containing MoO2, and the extraction of rhenium from exit gases. This technology allows economically efficient and environmentally safe processing of molybdenum concentrates: The degree of molybdenum extraction is 98.8%, rhenium-90%, sulphur-98.4%. The technology also ensures high extents of extraction of selenium and tellurium as well as the fixation of sulfur in the form of sodium sulfide or elemental sulfur.

Jan 1, 2006

By M. I. Kalashnikova

In hydrometallurgical technological flowsheets several methods of target components removal from solution are used. One of these methods is non-ferrous metals removal in the form of rich selective or collective concentrates. In the present work pyrometallugical mattes, thiosulphate containing solutions and pulps, iron powder with elemental sulphur and calcium sulphate were used as the precipitator. It was shown that depending on precipitator compound and process parameters non-ferrous metals precipitate from solution in the different forms with varying content of components including Ni3S2, NiS, Ni3S4, NiS2, (Ni,Co)S2, CuS; Cu1,765S; Cu1,97S.

Jan 1, 2006

By Gil Bourcier

A process has been developed for detoxifying spent potliner (SPL) in which the SPL is blended with limestone and an anti-agglomeration agent and thermally treated in a rotary kiln. The process has been proven and a commercial plant is in operation at Gum Springs, Arkansas. The treated by-product material has been delisted by the U.S. EPA and is now a potential raw material for many commercial applications. Finding uses for a non-hazardous material has many advantages over finding uses for a hazardous material like SPL. Complete usage of the by-product will complete the life cycle and eliminate any landfilling of non-hazardous SPL by-products or residues. Being non-hazardous and containing compounds used in the ceramic and numerous other industries assures many potential uses for the spent potliner by-product.

Jan 1, 1994

By Joël P. T. Kapusta, Romeo U. Pagador, Noparut Wachgama, Chumnoom Khuankla

"Thai Copper Industries (TCI) is a custom copper smelter and refinery in Rayong, Thailand, with an annual capacity of 165,000 tons of cathodes. It employs the El Teniente Technology as the primary smelting reactor to produce white metal from copper concentrates. The white metal is further treated in Hoboken Siphon Converters to produce blister copper then refined in anode furnaces before being cast into anodes for electro-refining in the on-site tankhouse.Thai Copper Industries is the first copper smelter to install and successfully operate on a commercial scale with the Air Liquide Shrouded Injection (ALSI™) Technology in the Hokoben converters with sonic injection of oxygen enriched air and nitrogen for cooling of the injector tip areas. Following commissioning and the establishment of operating practices, the performance of the Hoboken converters with ALSI™ Technology produced outstanding results. The unique combination of an El Teniente and Hoboken siphon converters, both of which are bath smelting operations, offers very high blowing and oxygen efficiencies. As a consequence, reverts recycling was accelerated with minimal build up on the mouth, end-plates or even below the siphon that is typical in Hoboken converters.These outstanding results in the Hoboken Siphon Converters with ALSI™ Technology helped the TCI Plant reach a production of about 75% of its capacity within four months despite the fact that the TCI staff is quite young and its converter know-how and experience are not yet fully developed."

Jan 1, 2009

By Olga A. Gomon, Alexey N. Lozhko

The technology of heat treatment for metal frequently includes multiple fast heating and cooling of the products surface. If the product is heavy-weight or long-size, its moving from a zone of cooling to a zone of heating and return require a long time. Other important condition of ensuring qualitative surface at heat treatment is intensification of cooling phase. It is known that turbulization of a flow activates heat exchange and increases efficacy of cooling without increasing volume flow rate of water. Additional difficulty is to ensure the regularity of heating and cooling on length of a product. The technology of cyclic heat treatment of rolling products, at which mobile zone of turbulent heat exchange is formed on the surface of a product, was developed and realized. The submission of water occurs through to face spray systems. Each of the systems has six long-range atomizers, which are located circularly. Two flows of water move towards one another along a surface of a product. When they collide, the right zone of turbulent heat exchange creates heat transfer in this zone of 10-15 time more intensive than on other surface of a product. The effect of moving turbulent zone on length of a product is reached by changing the proportion of volume flow rate of water, which is created by face sprays. The speed of movement for turbulent zone along a surface of a product is chosen so, that the cooling takes place on a small depth only. Then after passing the turbulent zone over a determined site of a surface, its temperature recovers fast owing to hot internal layers. The parameters of process were determined by mathematical simulation of cooling in an installation. The equations for dynamics of movement of collision point of flows, which were received this way, are interesting supplementary products of research. The experiments show that frequency of movement of turbulent zone is an important technological parameter. It defines mechanical properties of a surface and should be chosen depending on a profile of product and metal grade. The results of comparison of mechanical properties of a surface of various rolling products, which were received by developed and conventional technologies, are described in this report. Dependence of regularity of mechanical properties on frequency of movement of turbulent zone is adduced.

Jan 1, 1998

Silver has the highest electrical conductivity of all metals and consequently this property is an attractive feature which makes it a leading candidate for use in electronic devices. The research conducted was focused primarily on the development of a process for obtaining a deposited silver-coating onto alumina, for applications related to electrical-conducting devices and, ancillarily, catalysts. Alumina balls and plane substrates were utilized for the investigation. The coating process employed an aqueous arnmoniacal silver-nitrate electrolytes with a formaldehyde solution as the reductant. Modifying additives - an activator which would be expected to promote good deposition-characteristics onto the (dielectric) substrate and an inhibitor which would obviate homogeneous reduction (precipitation) of silver was observed when the activator-containing silver-electrolyte reductant constituents were combined. However, the silver-electrolyte/reductant system with inhibitor could be employed (at 80°C) to achieve a viable (subject to future research optimization) coating on alumina. The influence of the processing temperature on the deposition process was delineated during the course of the research. The morphology of the deposited-silver on the alumina balls was assessed by SEM imaging. A tape-peel test was employed, with the plane substrates, to semi-quantitatively characterize the adhesion to the alumina.

Jan 1, 1998

By James D. Navratil

Advances in hydrometallurgy require the introduction of new separation and purification processes, but they can be complex, costly and energy intensive. Chromatographic processes have low energy requirements and possess very high separation efficiencies. However, they have not yet made the great industrial impact that might be expected from their benefits. The large-scale and difficult separation of rare earths would greatly benefit from an improved continuous chromatographic operational device. Truly continuous, multicomponent chromatographic separations may be achieved by means of the continuous annular chromatograph. Work has been Initiated at The University of New South Wales involving the improvement and development of such equipment for the separation and purification of rare earths.

Jan 1, 1990

By Helmut Attlfellner

The selection of the best process for the oxygen generator for a metallurgical process requires the determination of all aspects which impact the economics of this facility. Concepts and features of modern air separation plants will be presented based on installed facilities for various metallurgical processes. The special features of advanced automation' of oxygen generators with load following and optimization of power consumption, automatic restart and unattended remote controlled operation will be investigated.

Jan 1, 1992

By Guillermo J. Román

The precipitation of copper and zinc as cements from a copper alloys' spent pickling solution has been studied at laboratory and pilot scale, with the objective of designing an economic process to recover both metals and render a solution to be either recycled to the pickling process or treated in a standard fashion and produce a non-hazardous sludge. The sulfuric acid spent pickling solution already containing copper and zinc was used first to dissolve another solid residue originated in the copper alloys foundry to neutralize part of the acidity. The resulting enriched solution was treated separately with two reductants,; sodium borohydride and iron powder varying pH and excess of reductant under constant agitation. Under the best conditions, precipitation of over 95 percent of zinc and copper was achieved together with the reduction of lead and cadmium contents respectively. A process for the combined residues treatment is proposed.

Jan 1, 1995

By T. T. Chen, J. E. Dutrizac

Noranda Inc., CEZinc presently employs a cement-stabilization (jarofix) process to stabilize its jarosite residues for direct disposal. In this process, Portland cement partly decomposes Na-jarosite to form Ca6Fe2(SC>4)3(OH)i2.nH20, ferric hydroxide and sodium sulphate which further reacts to form gypsum; approximately one-third of the Na-jarosite reacts in the current commercial product. The cured jarofix products also contain minor amounts of various Ca-Al-Fe silicate-sulphate-hydrate phases and traces of calcite. Together with gypsum and a Ca-Fe sulphate phase, these species bond the various particles together, imparting mechanical strength and reducing the permeability. Water-soluble Zn and Mg are stabilized in the Ca-Al-Fe silicate-sulphate-hydrate phases. The freshly cured products usually contain small amounts of moisture and traces of residual Portland cement, which provides additional alkalinity for the neutralization of any residual acid species. Jarofix products stored for more than six years in the laboratory, after curing, are usually dry and exhibit the same micro-textures as those of the freshly cured products. However, the stored products are depleted in the Ca6Fe2(S04)3(OH)i2.nH20 and Portland cement phases, and are enriched in gypsum and calcite which reflects the highly alkaline environment of the jarofix products. The aged products also have increased amounts of the Ca-Al-Fe silicate-sulphate-hydrate phases which have elevated Zn and Mg contents. This implies a further immobilization of residual water-soluble Zn and Mg during stora

Jan 1, 2000

By B. W. Lightfoot, Neill F. Arthur

"The AusIron process is a new development of the well established Ausmelt bath smelting technology(l). The development of this technology has been tied to the South Australian Steel and Energy (SASE) project which brings dedicated coal and iron resources together with this new technology. SASE is a joint venture between Ausmelt (40%), Meekathara Minerals (40%) and the South Australian Government through Mines and Energy South Australia (MESA) (20%). It will use a multiple lance furnace to process iron ore using steaming coal for both fuel and reductant.It is intended to build the simplest plant economically possible. Refinements such as preheating and prereduction of the ore are compatible with the technology but are not expected to be necessary in the first generation plant.The joint venture is negotiating with suitable partners for funding of the project through to commercial implementation at a target scale of2.5 mt/a of pig iron.ObjectivesAusIron aims to produce pig iron directly from steaming coal and from any of a variety of iron sources in a simple furnace system with a minimum of pre-processing of either coal or iron ore. Preheating and prereduction of ore are compatible with the technology but may not be necessary. The immediate aim is not to be the technology that uses the least quantity of coal to produce iron metal but rather the technology that uses the least number of dollars to produce metal.The chemistry of iron making is well known, probably better known than that of smelting of any other metal. Iron has been made for thousands of years and it is possible to make iron from charcoal and ore in a simple blast furnace the size of a beer barrel. The focus is therefore not making iron but rather making it more cheaply than it is made by current technologies. Large blast furnaces now set the standard and new technologies must perform better if they are to gain market share. It is still the cost of iron, energy units and capital going into these mega blast furnaces which ultimately set the market price for pig iron."

Jan 1, 1996

By Guo-hua Bai, Hong-jing Yuan, Qian Li, Yong-bin Yang, Tao Jiang, Yan Zhang

"The effect of different additives on the bio-oxidation of arsenic-bearing gold ores has been carried out to solve the problems such as long period of leaching, low oxidation rate. The oxidants strengthen the cathodic reaction and thus improve the leaching rate by the increase of electron transfer. Meanwhile, silver catalysis is also effective for the decomposition of arsenicbearing gold ores due to the strengthening of anode reaction. Co-intensification by oxidants and Ag (I) is more efficient to the bio-leaching and the conversion of As (III) because the anode and cathodic reaction of biological oxidation of sulphide ores were both strengthened. The leaching rate reached to 63.94% after bio-leaching 13days by co-intensification of Ag (I) and Fe(III).IntroductionWith the worsening global ecological problems and the gradual exhaustion of available gold resources, metallurgical technology of refractory gold ore has received more and more attention and become possible due to its good advantage of the economic effects and negative effects to the environment. Refractory gold ore, the direct cyanide leaching rate of that is defined as less than 70%, has become an important raw material in gold extraction industry, in which sulfide bearing gold ore represents a large proportion, pyrite and arsenopyrite (FeAsS) is a common gold-bearing mineral. Since the gold is often encapsulated in the crystal lattice of these minerals, destruction or alteration of the ore to liberate the submicron and/or structurally bond gold is necessary[l]. Even if the ultrafine grinding approach also is generally not sufficient for these refractory ores and additional techniques like roasting, pressure oxidation and bacterial oxidation are used to liberate the gold [2]. In the three pretreatment processes, bacterial oxidation is characterized by its new ideas, low cost, no pollution, simple equipment and operation, high leaching index and become the most promising process which has received much attention over time [3-5]. But its further application is limited by some of its own shortcomings, such as long pretreatment time and the toxic effects of arsenic to bacteria on bio-leaching limit."

Jan 1, 2013

By Kenneth N. Pike

The need to comply with environmental regulations and increase production has resulted in modifications to the East Penn blast furnace operation. Changes made include furnace design modifications, closed loop water cooling with heat recovery, automated weighing and charging, automated tuyere punching, ammonia scrubbing of tail gases and improved metal and slag handling to minimize environmental impact. These changes have resulted in a marked increase in yearly production and compliance with many of the air, water and solid waste regulations.

Jan 1, 1990

By Andreas Nolte

This paper includes a comprehensive report about the metallurgical utilisation of reusable products from electronic scrap recycling, car shredding industry, used glasses an various waste products, such as slimes and flue dusts, generated in a secondary copper smelter. Depending on the copper content, the type of copper compounds and the characteristics of accompanying substances, the materials are treated by smelting in furnaces, operating under reducing or oxidizing conditions. HKs pyro- and hydrometallurgical processes, blast furnaces, converters anode furnaces, tin lead alloy plant and tankhouse will be outlined. The reusable products are categorized according to the origin of the materials and then presented in the form of quantity and quality balances. Processing methods, process able quantities and quality requirements of inputs are described. The utilization degree of the most important metals (copper, tin, lead and zinc) is described with graphics. The report is rounded by information on operating licence according to the environmental regulations of the Federal Republic of Germany and data concerning supply and contracts

Jan 1, 1997

By Marcio Toshio Tanaka, Marcelo Breda Mourao, Cyro Takano, Cesar Yuji Narita

"The concerns in questions related to the environmental impact in the steelmaking industries caused mainly on the gas emissions such as the dioxide carbon are due to its raw material such as the coal, a fossil and non renewable resource. The purpose of this paper is to replace from 10% to 50% of the coal used in cokemaking by mixing it with a renewable source (wood charcoal). The powder (- 325 mesh) from both raw materials (coal and wood charcoal) were mixed in order to obtain a briquette that was then heat treated at 1100°C to obtain the biocoke. Results of usual analysis (coke reactivity index, coke strength after reaction and cold crushing strength test) were employed to compare to regular coke briquettes. It was found that biocoke with different amounts of wood charcoal present features enabling it to be used in some ore reductionprocesses.1. IntroductionThe iron and steelmaking industry is a heavy emitter of carbon dioxide; according to the World Steel Association, 6.5% of global emissions of this greenhouse gas is due to the production of ferrous materials [ 1]. This is due to the fact that the fuel and reductant employed in the blast furnace is metallurgical coke, obtained from fossil coal. There are some projects aiming to reduce or even eliminate the emission of fossil GHG in the iron and steelmaking process [2]. Most of them propose the capture and storage of the gas (CCS) [3], a technology not yet proven. Other studies point out that the coke consumption in the blast furnace could be reduced by using high reactivity coke; this could lead to lower temperatures in the thermal reserve zone of the blast furnace and consequently less fuel rate in the furnace.The use of biomass in the iron ore reduction process is known as an environmentally accepted solution, as biomass does not release already fossilized carbon."

Jan 1, 2013

By Yuchun Wang

In principle, supported liquid membranes could be an exceedingly elegant separation process. However they tend to fail by displacement and emulsification of the organic solution in the pores, which allows mixing of the feed and strip solutions. We have stabilized supported liquid membranes comprising moctylamine in nylon and PVDF supports by covering the pores with semi-permeable polyamide films, using an in-situ polymerization technique. Scanning electron microscopy demonstrates that the polyamide films are sensitive to production conditions and the nature of the support. The transport properties of stabilized supported liquid membranes for Cr(VI) are compared with those of unstabilized membranes.

Jan 1, 1998

By John L. Uhrie

Oxide stockpile leaching operations can realize increased copper recovery and decreased acid consumption from in-situ generated acid resulting from the oxidation of intentionally introduced pyrite recovered from mill tailings or other sources. While all oxide leach ores can benefit from pyrite addition, low acid consuming ores can show remarkably increased recovery and net acid generation; however, more highly acid consuming ores will show benefit more exclusively through increased copper recovery. Additional work shows that the value of highly acid consuming ores can be optimized by balancing copper recovery against acid consumption.

Jan 1, 1999

By Marc Liebman

We present the results of a telephone survey of electric arc furnace (EAF) steel producers. This report characterizes the current status of EAF dust generation, treatment and disposal. It indicates the quantity generated, zinc content, other relevant constituents, and plans and trends that will impact on the quantity and characteristics of the dust generated. The survey covers EAF based steel producers in the United States and Canada. It identifies the processors currently employed, opinions about the use of these processors and services, as well as new technologies being considered.

Jan 1, 2000