Search Documents

By Ralph P. Hackl

The Congress gold property, located near Goldbridge, B.C., is extremely refractory with most of the gold disseminated in fine- grained arsenopyrite. Metallurgical testwork conducted by Giant Bay Biotech Inc. indicated that biooxidation pretreatment was capable of increasing cyanide gold recovery from the ore to greater than 90%. To determine if the bioleach process could be successfully scaled up, a 225 cubic meter commercial size bioleach reactor was built and tested at the mine site in 1989. At that time the tank was the largest bioleach reactor ever operated. This paper discusses our experiences in operating the tank, summarizes some of the data obtained and describes the problems encountered.

Jan 1, 1990

By S. K. Sahoo, S. K. Sharma, U. K. Singh, G. S. P. Singh

This research focuses on the strata control issues in a Bord and Pillar depillaring working under the influence of dead load condition of voluminous and fragmented softcover of overburden dump material. It reports the modeling of a mine working through the FLAC 2D software under the Indian geo-mining conditions. The modeling results of an actual mine working under softcover were compared with that under the intact overburden condition to assess the influence of the soft overburden over the depillaring working. The modeling work involved progressive caving of the strata and the cyclic goaf filling following the modelsimulated occurrence of main fall and periodic caving. Mohr-Coulomb Failure criteria along with a simplified strain-softening (MCSS) model was used to study the failure and caving mechanism. Salamon’s compaction model was used to simulate compaction and resultant stress recovery in the goaf material. Comparison of the model findings was done in terms of load on supports, abutment stress, and convergence, apart from the stress redistribution and failure mechanism. The load transfer mechanism of the soft overburden was also studied for an overall understanding of the strata behavior in such workings.

Jun 16, 2020

By Alfred L. Anderson

Thorite and rare earth deposits in the Lemhi Pass area of southeastern Lemhi County, Idaho, are contained along complex shear and fracture zones and in reopened gold-quartz veins and copper lodes in quartzitic and phyllitic rocks of the Pre-cambrian belt series. Some of the shear and fracture zones are several tons of feet across and comprise broad zones of irregularly mineralized rock. These lodes contain a notable concentration of thorium and rare earth elements along with considerable amounts of barium, .potassium, calcium, iron, aluminum, phosphorus, sulfur, and silicon. The principal minerals are thorite, locally allanite, monazite, xenotime (?), apatite, specular hematite, barite, potash feldspar, occasionally calcite and quartz. Exept for some of 'the specular hematite, barite, reddish feldspar, calcite and quartz, the minerals are not distinguishable without the microscope. The thorite and locally allanite were deposited first, then the monazite and other phosphates, which were in turn followed successively by barite, potash, feldspar, calcite, and quartz. In exceptional cases, deposition of thorite and specular hematite was repeated after the feldspar. Some of the deposits contain several percent thoria, but the average os generally under one percent. The rare earth content is comparable with that of the thoria. The deposits appear to be of hydrothermal origin and are probably related genetically to late Cretaceous or early Tertiary igneous activity, manifested locally by a few dioritie and lamprophyric dikes.

Jan 1, 1959

By C. L. McKenzie

American Girl Mine is located in the Cargo Muchacho Mountains in the southeastern Imperial Valley of Southern California. Production from the current open pit mine and heap leach recovery system began in early 1989. Previous mining and gold recovery took place commencing in 1987 at the Padre Madre site, situated adjacent to the American Girl site to the southwest. In mid-1990, a 790-tonne-per-day underground gold mine and mill went into production. Approximately 6,500 troy ounces of gold per month are recovered from the combined open pit underground mine operation. Copper in the form of Azurite [Cu3(CO3)2(OH)2] and Malachite [Cu2CO3(OH)2] are abundant in the mined ores (Henshaw, 1942). The high solubility of these minerals in caustic cyanide solutions has a negative impact on carbon adsorption and electrowin processes. This paper presents the results of monitoring programs, process chemistry, and control changes introduced at American Girl Mine to abate production complications in the refinery and measures taken to minimize solution gold losses in the adsorption circuit(s).

Jan 1, 1993

By D. G. Chedgy

This article presents a novel design, called the Climax High Capacity Processor (HCP), for pre-combustion cleaning of coal. This design is particularly suitable for the plant capacities of 400 -660 TPH. The HCP is different from the conventional designs with an equivalent throughput in three major aspects: 1) the use of one large capacity HM cyclone to separate coarse and intermediate raw coal in a single circuit; 2) the elimination of the conventional secondary magnetics recovery system by use of the high efficiency Climax magnetic separators; 3) the use of "single line" piping with a minimum requirement of ancillary devices. In comparison with conventional designs with similar capacity, the HCP plant costs much less in capital investment, operation and maintenance.

Jan 1, 1997

By R. D. Deister

The Buick concentrator represents state-of-the-art technology in automated digital process control operation utilizing a centralized computer. The process control strategies implemented at Buick are no longer new to the industry, but the successful application of these developments is still rather unique in North America. Productivity improvements, determined to be a direct result of the process control developments, are the primary topics of this paper. Emphasis is placed on metallurgical benefits including both lead and zinc recoveries; lead concentrate grade; and reductions realized in reagent consumptions, operating costs, and personnel. A detailed description of the concentrator, along with a history of the process control development and a more in-depth discussion of the control strategies implemented at Buick can be found in the references. (The Buick flowsheet is depicted in Fig. 1).

Jan 1, 1987

By J. J. Reilly

The Vesta Mines of the Jones & Laughlin Steel Corporation operate in the Pittsburgh Seam in Washington County, Pennsylvania. This seam is overlain with a drawslate, 12" to 16" in thickness, which slimes readily when wet. Because of the need for a uniformly good quality metallurgical coal, the amount of reject, together with the top and particle sizes of the raw coal feed, is a serious problem at the Vesta Preparation Plant. The Preparation Plant operates two, seven and one-quarter hour shifts per day and processes 2,100 tons per hour of raw coal feed. The third shift is, used for planned maintenance of equipment. Since the water clarification equipment is so vital in insuring a uniform product, there is no alternative but that it be in operation at all times. To insure this continuous operation,. well-planned maintenance is a necessity. For years, Plant Management has kept performance records of the various units to determine the renewal dates of vital component parts, the length of wear, the various materials used in the manufacture of the equipment, and the labor cost for renewal. These records have been of inestimable help in planning an effective maintenance program to insure continuous operation of the various units.

Jan 1, 1959

By Duk-Won Park

A new gage for monitoring fractures in underground openings was successfully developed utilizing the reflection photo-elastic technique. The gage may be used to detect crack initiation in mine openings or tunnels so that remedial action may be taken to prevent further deterioration. Fringes concentrated around the cracks were spread by the use of rubber backing. Crack growth as little as 0.003 inch up to as much as 0.1 inch width were detected in this study. Variation of gage materials will provide alternative ranges. The feasibility of the method was tested and calibration was made in the laboratory study. Field study successfully demonstrated the capability of applications in detecting mine roof crack development.

Jan 1, 1982

By Danqing Gao, Brijes Mishra

Spatial variance of rock properties is an important characteristic of rock which addresses the heterogeneity of mechanical and physical properties and their effect on underground mining. Assessing spatial variance can be useful for both locating potential difficult grounds and performing reliability analysis in the mining support system. This study shows a microscale numerical model for rock material based on continuum mechanics. To consider the spatial correlation factor of mechanical properties in realistic rock mass, this study introduces a spatial correlation concept into the traditional type III extreme value distribution model. Based on the improved microscale random model, we conducted a series of numerical uniaxial compressive tests and one longwall mine model to investigate the progressive failure of rock. The results show that spatial correlation factor can significantly affect the load-deformation curves and fracture patterns. The spatial variance model was applied to a longwall mine that included several cutting sequences to observe the influence of the spatial variance on roof behavior. The cohesion and friction random fields induced failure that propagated randomly through the immediate roof in different entries. The results showed that the spatial variance provides an accurate prediction of erratic roof falls in coal mines.

Jul 20, 2020

By S. K. Kawatra, J. A. Halt

"Low-grade iron ores are finely ground and processed to recover iron-bearing minerals. However, the iron-rich powder is too fine to be used directly in blast furnaces and most direct reduction furnaces, and must be agglomerated or pelletized into a usable product called “pellets.” Bentonite clay has traditionally been used as a binder to make iron ore concentrate pellets, but it is expensive and contaminates the pellets. Organic binders may be a viable alternative to bentonite clay. This manuscript reviews organic materials that have been used to make iron ore concentrate pellets. Included are discussions on the development of organic binders, common pros and cons to organic binder use, organic binder structure and its effects on agglomeration, and additives to organic binders.IntroductionIron ore agglomeration turns finely disseminated, low-grade iron ores into a usable product, called pellets. During pellet production, fine-grained, iron-rich minerals are liberated from low-grade ores, concentrated, and agglomerated into round balls that are thermally hardened or cold-bonded to form pellets. Pellets are then transported to blast furnaces or direct reduction operations where they are used to produce iron; iron is further refined and shaped into the wide variety of steel-based industrial and consumer products in use today.Over the years, pellet production has become increasingly more prevalent with the increased exploitation of low-grade iron ores and increased iron and steel consumption around the world. In 2010, world iron ore pellet production was 388 Mt. It could be argued that the current pellet production process has been enabled by the use of binders – practical experience has shown that it would be nearly impossible to agglomerate iron ore concentrates using rotary drums and discs without using a binder."

Jan 1, 2015

By Arthur S. Cornford

According to Arbiter (Reference 1), the ball mill was invented by Brückner in Germany in 1876 and was first used in the United States on ores about 1905. The basic concept was a simple rotating cylindrical drum in which the tumbling action of the charge of material and grinding media resulted in size reduction of the material. Despite the very low mechanical efficiency of this method a number of factors have caused the tumbling mill to remain, by far, the most widely used piece of equipment for mineral grinding. The principal factors influencing this situation have been simplicity of design, ease of manufacture, ready adaptability to familiar material handling layouts and the absence of practical alternatives acceptable to the industry. In the early mills, the material was ground in batches, the mills being charged and discharged through doors in the shell. The shell was supported by means of solid trunnion shafts resting in plain bearings and the drive was accomplished through one of these shafts. In some later batch mills, the mill shell was supported on rollers which were also used to drive the mill. At an early stage, continuous operation was made possible by feeding and discharging the mill through hollow trunnions, the method still in most widespread use. The mechanical and structural design of the early mills was not an onerous engineering task. Norse sense and good practical knowledge were key qualifications. The mill shells had to be heavy enough to withstand the physical abuse they would receive in the field and the bearings had to have low enough unit pressures and sufficient wear retol to ensure several months of operation before the need for replacement occurred. When these requirements were satisfied, stresses developed in the equipment during operation were insignificant and the majority of structural failures were probably due to the use of inferior materials in manufacture. Over the years, the ever present demand for increased productivity has resulted in a steady Increase in the size of units of production equipment, including grinding mills. Arguments have been presented elsewhere, for and against the Idea of a high throughput single line grinding operation as opposed

Jan 1, 1972

By Robert E. Barrett

The history of mine safety legislation in this country is also a history of mine explosions. Nearly every piece of safety legislation that has been introduced or amended has resulted from some type of a disaster. When coal was first discovered and mined, it was extracted from along outcrops. As the coal became depleted near the surface, underground mining developed. When the first mine penetrated the outcrop, a great number of problems developed, many of which remain with us today. One of those problems is the potential for mine ignitions and explosions. Naturally, when underground mining progressed a few feet into the outcrop, some type of artificial light was needed. Early accounts of mining in Spain, Italy, Japan, and Great Britain indicate that torches served to light the mines. Later, candles were used, and still later, earthern oil lamps containing fish oil were used. As workings got deeper, explosions began to occur. When one did occur it was thought to be the work of goblins or the devil. As explosions became more frequent, it became very obvious that the use of open flames for lighting was very dangerous. A substitute was sought. Dried fish skins which gave off a weak phosphorescent light were tried. A mixture of flour and lime made from oyster shells called Canton phosphorous was also tried unsuccessfully. Fireflies in a bottle were also used.

Jan 1, 1976

By Ron M. Canon, John M. Begovich

Chromatography, ion exchange, and other techniques based on the interaction of solutes with solid phases offer versatility, high resolution capabilities, and near-universal potential applicability for the separation of valuable constituents in liquid solutions. The expense associated with obtaining reasonable throughput for these separations has been the only, albeit overwhelming, obstacle preventing widescale use of these methods. Attempts to devise continuous (cheaper) systems have previously resulted in moving, or simulated moving, beds of resin with complicated valving and timing sequences. These disadvantages, plus technical problems associated with the disturbing effects of non-plug flow and reduced resolution of moving versus packed beds, severely limit applicability of these systems. Over the past decade a new device has been developed that overcomes many of these problems. It utilizes a slowly (less than one revolution per hour) rotating annular bed of sorbent material with fixed-feed inlet and product withdrawal points. Numerous units of various diameters and lengths have been fabricated and operated, and a parallel effort has developed a satisfactory theoretical treatment of the device. Several simple control systems have been incorporated to thoroughly demonstrate the simplicity of operation, even for multiple products and multiplecarrier flows. This device has been developed using several metal solutions and has demonstrated its power with some of the most difficult, including the zirconium-hafnium, separations. Design equations are available for sizing units based on simple laboratory data and have been tested for units as large as 18 in. in diameter.

Jan 1, 1985

By Richard V. Wyman

The genesis of ore deposits has been tied to plate tectonics through differential petrogenesis in subduction zones. However, many mineral districts, especially in the Basin and Range province of United States and Mexico, appear unrelated to any possible subduction zones or to plate boundaries. It is proposed that the pattern of mineral belts is related to mantle plumes which have been overridden by an advancing continental margin.

Jan 1, 1976

By A. K. Bhasin

The movement of solid particles in a liquid represents an area of interest in many fields of science and technology. Knowledge of the behavior and characteristics of solid-liquid suspensions is of great importance to many areas of mineral processing. In order to characterize a solid-liquid system, the following factors must usually be considered: a) density of the liquid b) rheological properties of the liquid c) density of the solid particle d) size and shape of the solid particle e) volume fraction of solid particles f) relative motion of solid particles and liquid phase Other variables such as the effect of the containing vessel walls, Brownian movement, inter-particle friction, fluid slip and electrostatic effects, are important in special circumstances. Thus it is evident that a complete theoretical treatment is not possible covering all situations. Studies of the kinematic behavior of solid particles in a liquid have been approached by two methods: 1) Assessing the movement of a single particle and extrapolating to a multi-particle system; 2) Modifying the continuum mechanics of single-phase liquids in such a way as to account for the presence of solid particles. The first approach in general utilizes the method of particle mechanics. Extension to a multi-particle system gives rise to very complicated mathematical computation. The creeping motion equations do, however, furnish a practical, useful basis for achieving a uniform treatment and a better understanding of the phenomena. This approach is useful in the study of sedimentation and hindered settling processes.

Jan 1, 1971

By G. R. Addie

While the cost of transporting raw phosphate matrix from a pit to a processing plant via slurry pipelines is more efficient than it could be by rail cars, conventional trucks or belt conveyors, it still amounts to many millions of dollars, and in many areas there still exists much room for improvement. By taking advantage of pipeline test data on different slurries, it is possible to reduce costs by optimizing pipeline diameters, operating velocities and slurry concentrations. Better wearing, more efficient pump designs are now available which, if applied correctly, can lead to significant savings. The authors discuss what benefits are possible in relation to the electrical operating and wear maintenance costs and go into some of the factors associated with taking advantage of these benefits, identifying what they see as being practically possible.

Jan 1, 1998

By S. G. Hardcastle, K. C. Butler, M. G. Grenier

The most common method of determining airflow employed by mine ventilation engineers is the product of i) the average air velocity as measured by a vane anemometer and stopwatch through a continuous traversing technique, with ii) the cross-sectional area of the roadway. This method requires the vane anemometer to accumulate the total flow over the duration of the traverse. Historically, this has been facilitated by a mechanical analog instrument that has either a counter or set of dials that display the flow. Common instruments of this type are Airflow Development's AM5000, Davis's, or Taylor's Biram type anemometer. The AM5000 is widely used in the Canadian mining industry but is no longer available. Therefore, regulatory authorities have seen fit to evaluate presently available commercial instruments to replace the AM5000. This paper describes an instrument evaluation contracted by the Atomic Energy Control Board of Canada which regulates the uranium industry. Over the last two decades there have been numerous advances in the development of electronic air velocity meters. Currently available units have the following features: a) battery operation; b) are compact and can be hand-held; c) employ LCD's, and microelectronic circuitry; and d) provide a time integration for the duration of a traverse. These features make such instruments a possible replacement to the analog units and stopwatch determinations. This paper details five of the new generation of vane anemometers plus a vortex air meter, and it explores their limitations in comparison to analog units. Specific consideration is given to linear response, the effects of yaw, traversing speeds and ergonomics relating to both handling and use. The paper concludes with some features that are attractive and should be considered when purchasing a new anemometer.

Jan 1, 1991

By Jerry C. Tien

The rare earth elements (REEs) are a group of 17 chemical (metallic) elements. REEs are used widely in high-technology, clean-energy products as well as weapon systems. China's dominant position as a producer of over 95% of the world REEs output and the world's increasing reliance on REE products have highlighted concerns about the future availability of rare earths in recent years. This paper briefly reviews the REEs world reserves, production, consumption, the impact of our heavy reliance on REEs products and China's changing policies on REE export on world supply chain.

Jan 1, 2013

By A. L. Muler

Since 1956, when Broadbent and Callcott 1 proposed to analyze breakage processes by matrix methods, several authors and their co-workers have proposed various models of grinding that, in principle, could lead to fully automated grinding circuits. In particular, Meloy and Gaudin2, Gardner and Austin3, Kelsall and Reid4, Neloy and Bergstrom5, Callcott and Lynch 6, and Draper and Lynch have, by either computer simulation or by experimental data, or by a combination of the two, verified that comminution is reasonably well described by at least two functions: a selection function and a breakage function. The stage concept proposed by Callcott and Lynch6 requires that a classification matrix be included to completely describe breakage in an open circuit rod mill. The purpose of this work, portions of which are herein described, is to accumulate sufficient information on the breakage characteristics of quartz and magnetite in an open circuit rod mill, so that several of the theoretical and experimental approaches proposed in the literature can be compared with each other. Data is being gathered to compare the experimental method used by Kelsall and paid against the stage approach of Callcott and Lynch.

Jan 1, 1968

By C. T. Twort

As technology and economic conditions allow mines to operate at ever greater depths, increasing demands are placed on the environmental engineer to adjust the capacity of the installed mine . - refrigeration systems. At the same time the engineer must satisfy the changing legislation, which demands that developments are carried out in as an energy efficient and environmentally accept- able manner. Following the trends outlined above, this paper is written to give an overview of the current and potential future refrigeration technology available to the mining industry. The effects that may be produced by the adoption in mining applications of the new generation of 'green' refrigerants are examined both at the design stage and when considering the viability of retrofitting existing systems so that they comply with the Montreal Protocol. An introduction to the concept of Total Energy Warming Impact (TEWI) is provided, with an explanation of its use in optimising system design and performance, and its incorporation as part of an environmental audit strategy. The paper concludes with a discussion of innovative refrigeration techniques and the possible future developments in legislation.

Jan 1, 1997