Search Documents

By T. W. Beck, J. A. Organiscak

The U.S. National Institute for Occupational Safety and Health (NIOSH) Office of Mine Safety and Health Research (OMSHR) has recently studied several redirected scrubber discharge configurations in its full-scale continuous miner gallery for both dust and gas control when using an exhaust face ventilation system. Dust and gas measurements around the continuous mining machine in the laboratory showed that the conventional scrubber discharge directed outby the face with a 12.2-m (40-ft) exhaust curtain setback appeared to be one of the better configurations for controlling dust and gas. Redirecting all the air toward the face equally up both sides of the machine increased the dust and gas concentrations around the machine. When all of the air was redirected toward the face on the off-curtain side of the machine, gas accumulations tended to be reduced at the face, at the expense of increased dust levels in the return and on the curtain side of the mining machine. A 6.1-m (20-ft) exhaust curtain setback without the scrubber operating resulted in the lowest dust levels around the continuous mining machine, but this configuration resulted in some of the highest levels of dust in the return and gas on the off-curtain side of the mining face. Two field studies showed some similarities to the laboratory findings, with elevated dust levels at the rear corners of the continuous miner when all of the scrubber exhaust was redirected toward the face either up the off-tubing side or equally up both sides of the mining machine.

Jan 1, 2013

By S. Chander

The formation of surface films on pyrite has been studied through electrochemical techniques of cyclic voltametry and AC impedance measurements. The characteristics of the surface films depend upon the conditions of oxidation and the source of pyrite. At potentials near 0.0 V, some pyrites have large values of polarization resistance showing a certain degree of passivity. Some pyrites show more passivation than the others, however. On oxidation, metastable phases of Fe(OH2) and Fe(OH3) form which transform to more stable 3 phases on aging. The growth of surface films near the corrosion potential of pyrite follows a linear kinetics which is attributed to a chemical (or an electrochemical) reaction as the rate determining step. The surface film is considered to be a hydroxide or an oxide rather than sulfur because the later is expected to be limited to a monolayer in alkaline solutions. This study has also demonstrated that AC impedance measurements can be used to study the growth characteristics of films at mineral/ solution interfaces.

Jan 1, 1987

By K. V. K. Prasad

Stochastic simulation has been routinely used for performing risk and sensitivity analyses in a variety of fields. The commonly used means of generating the simulations has been the Monte Carlo approach which usually employs a Simple Random Sampling (SRS) scheme of the variable distributions. This method is prone to sample clustering and requires a large number of samples to represent the distribution faith-fully. This can become problematic for simulating complex processes where it is impossible to run an arbitrarily large number of replicate simulations. The Latin Hypercube Sampling (LHS) method uses a stratified sampling approach which assures representation of the input distributions for any given number of samples. In this paper the LHS and SRS approaches are compared using a petroleum resource estimation example.

Jan 1, 1993

By Haydn H. Murray

This paper presents the results of test work performed with a Pacific Electric Motors (PEM) high intensity magnetic separator (20 kilogauss) , a unit capable of separating weakly, as well as strongly, magnetic minerals in the particle size range of sands to clays. Tests were performed on some 40 industrial minerals. With some minerals excellent separations were attained and with others intermediate and poor separations were accomplished. This study is a preliminary survey and many of the intermediate and poor results can be improved as separation problems are worked out with additional test work. It is demonstrated that with a number of industrial minerals high intensity magnetic separation is a viable beneficiation technique that is economic ally feasible.

Jan 1, 1976

By Brett Schug, Caelen Anderson, Sohail Nazari, Carlos Cristoffanini

"The Haile gold mine in South Carolina is increasing the automation level of its processing plant in order to improve operational stability. One step toward this goal is the application of a digital twin concept to provide virtual instruments. Haile has engaged Andritz to implement virtual instruments at its grinding area hydrocyclones and at its tailing thickener underflow pump. These virtual instruments provide density values in a traditionally difficult location for reliable slurry density measurement. The digital twin is a first-principles integrated design engineering with advanced simulation (IDEAS) simulation model, connected in real time to the control system. Results have been promising, with the virtual instrument values matching the physical instrument under normal operating conditions and showing better prediction under upset conditions. Haile plans to use the virtual instruments as optional process control parameters.OceanaGold’s Haile gold mine is located near Kershaw, SC, about 80 km (50 miles) southeast of Charlotte, NC. This location was first mined in 1827 and has produced gold through several operating periods since then, including a heap leaching operation from 1985 through 1992. In October 2015, OceanaGold acquired Romarco Minerals, the previous owner of the Haile operation.The current operation began in 2017 as an openpit mine with additional underground resources. The nameplate throughput is 5,760 t/d (6,350 stpd) ore, and 2017 production was 3,345 kg (118,000 oz) gold, with 3,968 to 4,384 kg (140,000 to 155,000 oz) gold expected in 2018. Proven and probable reserves exceed 85 t (3 million oz) gold at a grade of 2 g/t (0.06 oz/st) gold. The process, as shown in Fig. 1, includes a primary jaw crusher, comminution with a semiautogonous grinding (SAG) mill and ball mill circuit, flash flotation, rougher flotation, regrinding, pre-aeration, carbon-inleach leaching, carbon elution and regeneration, cyanide recovery, electrowinning and refining. The Haile operation’s inaugural gold pour took place Jan. 20, 2017. Mine life is expected through the year 2030."

Dec 1, 2018

By Steve Tadolini

Underground roof falls can have devastating effects on the safety of operations personnel, and equipment, and seriously impact production. Immediate steps are usually taken to danger off and secure the area while clean-up efforts are designed and implemented. A critical step, often overlooked due to production demand, is the determination of - why the roof fall occurred so that additional occurrences can be avoided in future developments or what measures can be taken to identify areas that have similar ?symptoms?? Forensic engineering includes the investigation of materials, products, structures or components that fail or do not operate/function as intended. The authors define forensics in ground control engineering as the study of evidence discovered while examining underground roof falls by applying expert observational techniques and established mining engineering principles to determine the probable cause, hypothesize solutions, and design engineering safeguards to prevent reoccurrences. Simply stated, the primary steps in the forensics of underground roof fall techniques are: ?Assess regional and local conditions prior to the event. ? Assess post-event conditions. ? Hypothesize plausible ways in which the pre-event conditions became the post-event conditions. ?Search for evidence that either denies or supports the various hypotheses. ?Apply engineering skill to relate the various facts and evidence into a cohesive scenario of how the event may have occurred. This paper details the proposed technique by utilizing a roof fall case study that required the examination of five primary factors: mine design parameters, excavation geology, method of excavation, method of support, and mining cycle times.

Jan 1, 2009

By Lester E. Sutton

The past three years have been the most difficult period in the modem history of the barge line industry. Having withstood the fuel cost run ups of the late 1970s and the imposition of inland waterways system user fees, the industry has struggled more recently with an overcapacity problem of unprecedented proportions. In responding to these challenges, the industry is undergoing important long-term structural changes, with the various individual barge lines pursuing an array of divergent long-term business strategies. This paper discusses these strategies in terms of their probable impact on the industry as a whole, and argues for the survival of a competitive number of large, national, independent barge lines as the outcome most in keeping with the long-term interests of the mining and minerals industry.

Jan 1, 1986

By Alain S. Kivava, Olawale K. Aromolaran, Charles Nzolang, Anthony T. Bolarinwa, Georges M. Kasay

Rare earth elements (REEs) are crucial in high-tech and green technologies. The Democratic Republic of Congo (DRC), rich in mineral resources, shows potential for REE deposits in carbonatites, pegmatites, and placers. This paper reviews global REE resources, highlights potential REE targets in Africa, and emphasizes the need for further research and exploration in the DRC to unlock its REE potential.

Feb 4, 2022

By Randal J. Barnes

There are many methods available for the estimation of geologic parameters (Popoff, 1966; Barnes, 1980). In the last decade a new and relatively sophisticated technique using statistical theory has emerged: geostatistical kriging (David, 1977; Journal and Huijbregts, 1978; Rendu, 1978). An interesting property of geostatistical estimation is that when a geologic parameter is estimated for a given volume, not only is the estimate generated but an associated measure of certainty is produced as well. This statistical measure of estimation confidence is called the estimation variance. While the concept of an estimation variance is universally considered to be a good idea, mining engineers and geologists do not currently have the tools to incorporate it into their planning and quantitative analysis. This paper attempts to develop and present some of the necessary tools required to incorporate estimation uncertainty into mine planning. Geologic uncertainty is portrayed as an economic business risk. This risk is objectively characterized, and-the associated cost is quantified. Geologic delineation sampling is viewed in this light as an economic commodity with an associated cost and value. A coal mine planning example is used as a focus in this presentation. The data used is real, though it has been modified to maintain data security and project anonymity.

Jan 1, 1986

By V. Z. Sun

One of the major concerns of ground control in a coal mine is safety against failure of one of three components (i.e. roof, pillar, or floor) of the mine entry. In order to better design and evaluate stability of the mine entry with a certain confidence, a reliability approach is introduced rather than using the conventional safety factor (SF) method only. Advantages of using the reliability approach is that it not only takes variability of both rock/coal properties and stress distribution into consideration, but also assesses the stability of each component and mine entry as a whole system. Therefore, it is anticipated that, by using this approach, the current ground control technology in coal mine will convey a better sense of confidence. The results of a case example show a significant influence on the current design concept and stability evaluation of mine entry.

Jan 1, 1997

By Carl Barchet

INTRODUCTION Located on the Colorado River on the Nevada-Arizona border about 56 km (35 miles) southeast of Las Vegas, Nevada, Hoover Dam is a gravity arch dam 221 m (726') high for electric power generation and water supply. The head waters of the dam form a large reservoir, Lake Mead. The dam is equipped with two emergency spillways, one in the Nevada abutment and one in the Arizona abutment. Both spillways which are concrete lined and 15.25 m (50') in diameter, were intended for use only if Lake Mead is full and incoming flow of the Colorado River exceeds the discharge capacity of the turbines and regular bypass conduits. In the spring of 1984, a combination of rain and unusually rapid snow melt required the opening of the spillways for only the second time in the 50 year history of the dam. As in the previous use in 1942, the massive discharge of water through the tunnels resulted in severe damage to the concrete Linings of both tunnels. This damage is the result of cavitation which occurs as the discharge water flows at very high velocities over minor irregularities in the concrete lining. The U.S. Bureau of Reclamation has long been aware of the cavitation effect which occurs during these high volume discharges and has been studying solutions. One solution to the problem is to induce air bubbles into the flowing water to eliminate the vacuum associated with cavitation. This solution had been implemented at Yellowtail, Flaming Gorge, Blue Mesa, and Glen Canyon dams by constructing an aeration slot in the inclined portion of their spillway tunnels. Since the spillways of Hoover Dam were already in need of repair, the BUREC decided to construct similar facilities in each of the two 15.25 m (50') diameter spillways coincidental with the other repairs required.

Jan 1, 1987

By Ralph W. Barbaro

This paper presents a cyclic queueing model which evaluates the productivity of a shovel-truck materials haulage system. For a cyclic queueing problem with exponentially distributed service times, a cyclic queueing model provides exact solutions in a fraction of the time that simulation takes to produce an approximate solution. The model is applied to an example problem, and the results are validated with simulation. Simulation is used to show that the assumptions of exponentially distributed service times and steady-state are not serious problems. A cyclic queueing model can be used to quickly obtain an accurate assessment of the productivity of a shovel-truck system.

Jan 1, 1986

By John D. Katsllometes

In the mining and processing industry, the maintenance plan has often evolved rather than being consciously set up resulting in an overreliance on breakdown and fixed-time maintenance (planned maintenance). Historically mining and processing plant equipment has been robust and less automated than modem equipment, making it relatively easy to work on. Mining and processing plants have relied on large and expensive maintenance departments to enable rapid attention to breakdowns. Maintenance itself can result in excessive downtime and costs. This results from the requirement to take the machinery off-line to carry out (possibly unnecessary and invasive) maintenance. The danger of infant mortality after it has been put back on line again and also the cost of the maintenance action itself contributes to costs. A goal of any well-run maintenance program is to have the lowest cost while providing 100% capacity 100% of the time to operations. When maintenance investments are at a minimum, the cost of lost production is at its highest. As maintenance effort and investments are intelligently increased, the production loss gradually decreases until the lowest combined cost is achieved. This is the maintenance goal. A road map is needed to achieving maintenance excellence. This article addresses a "Road Map" to achieving maintenance excellence. INTRODUCTION Mining and processing industry maintenance is big business. A world-class maintenance program is characterized by maintenance excellence.

Jan 1, 2004

By Malcolm Scoble, Sean Dessureault, Scott Dunbar

Budgets are key financial and behavior drivers for most businesses, including mining. Budgets are used to link strategic objectives to tactical decisions, to measure performance, and to provide basic financial planning. More accurate and pertinent budgets should result in improved strategic decision making and performance measures. This paper discusses how a process based production and cost database, based on activity based costing models and the one year production plan, can be used to create the annual budget for an operating mine as an Activity Based Budget (ABB). A case study is used to compare budgets derived from traditional methods and an ABB approach. It is evident that the ABB method is more accurate.

Jan 1, 2002

By Bill Sayer

Cadman, a wholly owned subsidiary of Heidelberg Cement, is a leading supplier of sand and gravel as well as ready mix concrete in the greater Seattle area in western Washington State. Cadman's aggregate mine is located in North Bend, 34 miles east of Seattle, WA, and consists of a "Lower Pit" and an "Upper Pit." In 2005, Cadman planned the upgrade of the North Bend mine operation as follows: Upper Pit (Figure 1): 1. Crushing Plant, Stacker and Stockpile 2. Storage Reclaim Belt Feeders 3. Feed Conveyor 4. Downhill Overland Conveyor Lower Pit (Figure 2, Photo 12): 1. Radial Stacker 2. Storage Reclaim and Truck Load-out

Jan 1, 2008

By R. G. Eggert, M. R. Walls

A mining CEO's willingness to participate in risky investment opportunities significantly affects a company's strategic-investment decisions. Decision-analysis techniques provide a mechanism for measuring a CEO's risk tolerance and ability to make formal comparisons of risk propensity among mining firms. The authors developed a methodology for measuring CEO risk tolerance. The findings from a confidential survey of mining CEOs are presented. The results from the survey suggest that: •mining CEOs are overwhelmingly risk averse when considering investment decisions; •CEOs of small mining firms are significantly more risk averse than CEOs of large mining firms; and •there appears to be some differences between Australian and non-Australian CEOs regarding their willingness to participate in risky investments. The results of this survey suggest that CEOs are pursuing objectives other than, or in addition to, maximizing shareholder wealth and that they act to reduce the financial exposure associated with strategic investments.

Jan 1, 1997

The Kinross DeLamar Mine has been operated for more than 17 years producing precious metals dore' from ores, principally silver bearing with associated gold co-products. In late 1995 a new orebody was commissioned, the Stone Cabin orebody, and the site began a phased shift from silver dominance to gold dominance in terms of precious metals revenue. The Knelson Concentrator was selected to remove gold from a portion of the cyclone underflow stream in the grinding circuit. This paper describes the development of the flow sheet, specific mineralogical impacts on Knelson product and downstream materials, and impacts on mine/mill grade reconciliation.

Jan 1, 1997

By Frank Matter

The production of ultrafine slurries and powders is possible with small media made out of Si02, A1203, Fe203, Zr03 or other raw materials due to the fact that since approximately 12 years from now, entirely new machines have been developed which allow to use this small media for the production of ultrafine pigments. Basically we distinguish between two grinding methods which are: A.) Dry Grinding with Air Classification: This method is used for more than fifty years but only since four years this technology is realized with small grinding media. Many problems like cooling, abrasion, control of the media flow, separation media from product, grinding media recycling etc. had to be resolved before it was possible to get in full production with this new system. Hereafter a flow-sheet of such a TRZK mill with an air classifier especially designed to produce end products with a top size between 2,5 and 3,0 micron and with an average particle size between 0,3 and 0,5 micron.

Jan 1, 1983

By R. P. Plasket, G. M. Dunn

The cobalt plant was successfully commissioned in mid-1983. It is located within the company's nickel - copper re finery situated in Springs, South Africa. Plant design, which began in 1981, made provision for the corrosive process environment, stringent environmental standards, and the latest noise abatement requirements. In addition, the process flowsheet for the primary recovery of the cobalt byproduct and the purging of six impurity metals (nickel, iron, copper, manganese, lead, and arsenic) was designed with simplicity as a primary objective. High purity cobalt powder has been produced since commissioning.

Jan 1, 1987

By F. J. Sotillo

The objective of this investigation was to determine the feasibility of using a high-pressure roll mill (HPRM) to improve the separation efficiency of dolomite from apatite in downstream operations when treating high-dolomitic pebbles. High-dolomite samples from four phosphate mines were used for the test program. The research work plan included sample characterization studies; INSTRON tests to develop preliminary crushing data; high-pressure roll mill evaluations to determine crushing parameters, such as feed rates, rolls speed and gap, and applied torque, pressure and energy; and screen, microscopy, and flotation studies to assess dolomitelapatite separation efficiency. The results of the HPRM tests show that commercial products for all four mines can be obtained. Recoveries of 74-82% of the P2O5 and rejections of 46-83% of the MgO were reported with an specific energy consumption of 0.2-0.5 of that of a laboratory rod mill.

Jan 1, 1998