Search Documents

By A. T. Yu

The broken hill proprietary company Ltd., Australia's only steel producer, has come a long way. Since 1885 to reach today's. Capacity of 6.6 million long tons of ingot steel per year.* its Newcastle steel complex in New South Wales, located 100 miles north of Sydney and on-stream since 1915, has likewise shown continued impressive growth (fig. 1). The most recent expansion plans at Newcastle call for sub¬stantially increasing its production, with the help of some added facilities, but principally relying on the increase in efficiency of the furnace operation. Its modern raw materials blending system will playa major role in meeting Newcastle's new targets.

Jan 1, 1969

By D. W. Frommer

Processing nonmagnetic taconites by selective flocculation-desliming and flotation requires large volumes of water. If impounded without treatment these off-process waters require excessively large areas for containment. To discharge the waste water into natural waterways would contribute to stream pollution and likely would not be permitted. In Bureau of Mines experiments conducted in the Twin Cities Metallurgy Research Center&apos;s 900-lb/hr pilot plant, approximately 85 percent of water requirements for the flotation-based treatment of a Michigan nonmagnetic taconite were met by reclaimed water. Water reclamation of the off-process streams from flotation was accomplished by controlled additions of lime, sodium carbonate, and a synthetic flocculant to reduce turbidities to <1,000 ppm equivalent Si02, while maintaining a Ca(II) content of 516 ppm in the finished effluent. Flotation concentrates of good quality were obtained using the reclaimed water. The cost of chemicals used in water reclamation was approximately equal to the savings in flotation reagents attributed to recycling of the water.

Jan 1, 1970

By I. Papadopoulos

Nowadays, geophysical prospecting is implemented in order to resolve a diversity of geological, hydrogeological and geotechnical problems. Though plenty of applications and a lot of research have been conducted in the country-side, only a few have been reported in the literature concerning urban areas, mainly due to high levels of noise present that aggravate most of the geophysical methods (e.g. electromagnetic, seismic, gravity etc.) or due to spatial limitations that hinder normal method implementation (e.g. electrical). Among all geophysical methods, electrical tomography proves to be the most rapid and urban noise insusceptible technique. This work presents a case study in the urban area of Hania (Crete I., Greece), where Electrical Resistivity Tomographies (ERTs) have been carried out for the detection and identification of possible buried ancient ruins or other manmade structures, prior the foundation of a building. Nineteen profiles were surveyed in a 20x40m grid using dipole-dipole configuration. The results indicate two areas of interest, that are interpreted as probable old wells, in the context of the existence, in former times and in the same area, of an olive oil plant. In the vicinity, near surface ancient ruins have been disclosed, but no such evidence provided this survey, for the particular area under study and the prospected depth. The collected ERT-data were processed by applying advanced algorithms in order to obtain a 3D-model of the study area that depicts more clearly and accurately the interesting subsurface structures.

Jan 1, 2005

By H. Habenicht, E. Urschitz

Three mining methods for full extraction in flat coal seams - i.e., longwall (L W), shortwall (SW), and rib pillar extraction (RPE) - are com- pared with each other in view of the introduction of a mechanized, self-advancing roof support. Features are shown according to which RPE appears most attractive under certain conditions. In this presentation, the mining methods are outlined and discussed. The new support (Alpine Breaker Line Support, ABLS) is described, and its employment is explained. A trial operation in RPE using the ABLS has been conducted successfully in a South African coal mine. The results and improvements are stated.

Jan 1, 1988

By George K. McCord

It is a pleasure to participate in this Fall meeting of the Society of Mining Engineers to discuss energy conservation trends in the cement industry. Energy is the "life blood" of American industry, and the ability to use available energy resources efficiently may well determine the future of our nation and of its industries. The Federal Energy Administration has classified cement manufacture as one of several energy-intensive industries in the U.S. and has selected the Portland Cement Association to make a detailed study of possible energy conservation measures. Member companies of the Portland Cement Association represent about 85% of the cement producing capacity of the United States and 100% of Canadian capacity. Stated briefly, the purpose of the Association is to extend the uses of portland cement and concrete through research and development, market promotion, education, and public affairs work. PCA&apos;s general offices and research laboratories are located in Skokie, Illinois. Our staff of engineers, scientists, and research personnel make the PCA uniquely qualified to perform an energy conservation study of the kind requested by FEA.

Jan 1, 1975

By L. J. Buchanan

The relationship between hydrothermal ore deposits and hot spring systems has received intensive study in recent years, particularly as a consequence of interest in the energy potential of geothermal systems. Base and precious metal deposition in surface pools and at shallow depths in modern geothermal systems has been recorded in numerous publications (1, 2, 3) Theoretical studies of hydrothermal fluid flow at depth, connected to surficial hot springs systems, have been presented by White and others (1), Cathles (2) , Henley and McNabb (3). As a result of these and additional studies, numerous hydrothermal ore deposits are thought to have originated as genetic parts of larger geothermal systems. In particular, it appears that metal precipitation is greatly enhanced in zones of boiling where volatiles and steam are escaping (4). High grade, near surface concentrations of base and precious metals, deposited as a result of partial vaporization of rising fluids, are such a common aspect of modern not spring systems that ore deposition models are becoming based on what may be called a geothermal model. In its most general terms, this model requires an anomalously high thermal gradient which acts as the driving force behind a convecting hydrothermal system. The water may be entirely meteoric or may be In part at least of other origins. The water migrates towards the higher temperature area, becomes heated, and picks up alkalies and metals by dissolving minerals along the fluid path. As water exits to the surface above the heat source, a mass balance requires the incoming hot water to rise to replace the lost water. As the water rises past the elevation where the hydrostatic pressure is insufficient to prevent boiling, then boiling will occur. Depending on the salinity and the temperature of the water, boiling can occur anywhere from great depths to near surface. Boiling results in a loss of volatiles, a pH rise in the fluid phase, cooling of the remaining fluid, a rise in oxygen fugacity, a concentration of salts in the remaining liquid, and precipitation of ore and gangue minerals.

Jan 1, 1980

By James M. Barker

The occurrence of borates and zeolites at Mesa del Alamo is well documented by McAnulty and Hoffer (1) and Lefond and Barker (2). Further investigation indicates the presence of priceite and meyerhofferite in addition to the howlite (1) and colemanite (2). Analcime occurs in addition to the clinoptilolite and phillipsite (2). The Mesa del Alamo area is about 200 !a south of Tucson, Arizona, and 13 km southeast of Magdalena, Sonora, Mexico, just south of the unpaved road to Cucurpe (Figure 1). The geology and mineralogy of northcentral Sonora is known only on a regional basis except for small areas mapped in detail during copper exploration. The study area is within the Basin and Range province of North America from which borates and zeolites are now produced in California. The borates and zeolites at Mesa del Alamo occur in geological environments similar to those of the Mojave and Death Valley regions of California (3, 4). Thus, a detailed exploration pro- gram in the Magdalena area could result in the discovery of economic borate and/or zeolite deposits.

Jan 1, 1979

By Keshavan Nair

In connection with Project Payette, which is concerned with the detection of underground nuclear explosions, it was necessary to determine the technical feasibility of constructing and maintaining a large (approximately 315 feet in diameter) unsupported underground cavity at a depth of approximately 2700 feet in the Tatum Salt Dome in Mississippi. The dimensions and the location of the cavity in the salt dome were governed by criteria laid down by the Atomic Energy Commission. Within the framework of the specified criteria, cavities of various shapes and dimensions could be utilized. One aspect of the feasibility study was to investigate the structural stability of various cavity shapes and to recommend a preferred shape. This paper summarizes the studies that were conducted to evaluate the structural stability of various proposed cavities.(l)

Jan 1, 1968

By R. H. Olson

Pigments are used in two segments of papermaking, as the major component in paper coating formulations and, in small percentages, as fillers in the paper web. Historically, the dominant use has been in coating, however, recent developments have fostered a multifaceted effort to substantially increase the pigment component in the paper furnish. Factors responsible for these developments together with their relationship to recent and forecast changes in papermaking technology are reviewed. Finally, some thoughts are presented on the probable timing and extent of these changes as well as their expected impact on the future demand for the common paper pigments.

Jan 1, 1985

By R. A. Williams

Surface and electrochemical techniques have been used to describe the surface chemistry of ferrosilicon powders, as a function of pH and electrochemical potential, for conditions typical of operating DHS plants. The practical consequences on the likely corrosion behaviour and associated electro- kinetic particle-particle interactions (which affect stability to sedimentation) in the suspension, are discussed.

Jan 1, 1987

By George Vranesh

Synfuels development in the upper Colorado River basin and the population growth attendant with such development demand sizeable quantities of water. Unfortunately, the water supply in the basin is limited and such limitation may impose a significant constraint on the development of the West&apos;s abundant energy resources. Although the water for the synfuels development will be governed by the law of prior appropriation adopted in the upper basin states, the authors point out that an apparently senior water right .my not deliver a firm supply of water. The federal and Indian Reserved Water Rights Doctrine, the Colorado River Compacts the Doctrine of Equitable Apportionment, and the federal and state environmental laws can all severely diminish the value of any given water right and the synfuels industry should take care to evaluate these factors in acquiring its water.

Jan 1, 1981

By H. Shafick Hanna

The major problems are identified the high phosphorus content and the fine dissemination or encapsulation of mineral impurities, in, ,the iron bearing minerals, A process which combined extreme fine grinding techniques with magnetizing roasting or flotation separation methods, is suggested. By these methods concentrates assaying 60-61 percent Fe exceeding the widely accepted upper limit of 56 percent Fe set for these ores, were produced with 75-90 percent iron recovery. Moreover it was shown that the phosphorus content of these concentrates could be reduced from 0.25 to 0.03 percent phosphorus by acid leaching. A brief discussion on production costs based on current and future developments in iron ore processing is given.

Jan 1, 1980

By N. P. Titkov

This paper presents the results of laboratory and pilot plant investigations for the development of efficient methods of beneficiating hematite ores from the Krivoi Rog, Kursk Magnetic Anomoly, Olenogorsk, and other localities. The tests included gravity, magnetic (in a high intensity field), flota¬tion, and magnetizing roasting methods. It was possible to develop efficient beneficiation methods depending on the mineral composition of the ore and degree of dissemination of ore and gangue minerals. The paper shows the relationship between the iron silicate and quartz content of the ore and the technologic indices of the various beneficiation methods. Some of the conclusions based on these investigations and the technical and economic computations related to the cost of one ton of pig iron produced from concentrates obtained by the various beneficiation methods are: 1. If the hematite ore is not disseminated uniformly, it is expedient to use a combined gravity and flotation process. Ore particles up to 50 am. in size are beneficiated by gravity (heavy suspension, jigging, and others) and yield a lump concentrate. The middlings from this process are recrushed and floated; 2. Finely disseminated hematite ores, containing small quantities (less than 5 percent) of iron silicates, are most effectively beneficiated by flotation. Anionic (sulphate soap, tall oil emulsion with various foam depressors) as well as cationic collectors may be used. Depending on the mineral and chemical composition of the ore, it is possible to obtain concentrates containing up to 65 percent iron with an extraction up to 94 percent; 3. Finely disseminated, mixed hematite-magnetite ores may be beneficiated by flotation or a magnetic separation-flotation process; 4. Finely disseminated hematite ores, containing large quantities of iron silicates and earthy hematite ores are most efficiently beneficiated by the magnetizing roasting method. This method will yield concentrates containing up to 68 percent iron with extractions up to 90 percent. Although beneficiation by the magnetizing roasting process is costly, it will nonetheless, when employed on this type of ore, yield the least expensive pig iron.

Jan 1, 1960

By Thomas A. Gwynn

When Lewis and Clark first pushed their boats up the Missouri River, Meriwether Lewis reported the presence of coal in the western states by saying in 1802 that it "burnt tolerably well and afforded but little flame or smoke but produced a hot and lasting fire". Lewis would have been amazed and bewildered at the history of coal development in this region and the more recent political-socio-economic-environmental confrontations of today. Certainly without this coal the railroads would not have readily pushed into our western states, and the progress of this region would have suffered. The coal industry has passed from a period when "coal was king" to a period of depression in the industry, but its importance is being revived. A contributing and simultaneous environmental concern has emerged in the nation and in many states during the past ten years, partly caused by newly imposed standards for sulfur content of fuels. Much of the midwest and eastern coal cannot be used because of high sulfur content, shifting attention to the low sulfur coal deposits of the western states. In the western states, lands disturbed by strip mining or even underlain by strippable coal are small compared to the total acreage, and usually mining operations are on lands not under cultivation. There are some farm lands being disturbed by surface mining, but this is often over-emphasized. In states like New Mexico and Arizona the percentage is less. The value of the minerals underlying the surface certainly must be considered along with the value of the surface, and sometimes proper reclamation following mining can result in higher ultimate usage of the land.

Jan 1, 1974

By William E. Saegart

Copper has been mined in the Philippines since at least as early as the Ming dynasty (1368 A.D. to 1644 A. D.). The principal source areas of this early production were in Camarines Norte (Paracale), in the Mountain Province, which now boasts the largest number of Philippine porphyry copper deposits, in Masbate and in Surigao, The Spanish Era began in 1521. Although they were primarily interested in gold, the Spaniards operated several copper mines including the San Remigio mine on Panay and the Lepanto mine in northern Luzon, beginning in 1842 and 1865 respectively. Prior to World War II most of the Philippine copper production was supplied by these same two mines together with the Hixbar mine, Rapu Rapu Island which began operation in 1939. The Hixbar and San Remigio mines are cupriferous pyrite deposits and the Lepanto is a vein-¬form replacement deposit (Kinkel et al. ,I 1956). No significant copper production was derived from porphyry copper occurrences prior to world War II.

Jan 1, 1976

By Daniel R. Walton

This paper covers several points of interest to mine engineers and planners involved in evaluating or conducting geostatistical coal reserve estimates. In particular, the ability to optimize borehole drilling locations and minimize drilling costs is addressed. Also discussed is the concept of confidence intervals for estimated coal characteristics obtained through geostatistical estimates and their importance in decision-making for mine planners. Finally, a discussion is presented on how geostatistics enables identification of invalid data points and actually forces strict attention to data editing and proper geologic interpretation.

Jan 1, 1982

By P. D. Rao

Although phosphorus is a very important biogenic element, its concentration in coal is generally low. Phosphorus concentrations typically range from 0.001 % to 0.229% in raw coals of the contiguous 48 states. Some Alaskan coals in the Cook Inlet region contain horizons unusually high in phosphorus. A foot by foot analysis of deep drill core, containing 70 ft. of sub bituminous &apos;C&apos; coal from the Beluga coal field, Alaska, showed certain increments contained as high as 17.03% P2O5 in the coal ash; 1.01 % P on a moisture-free coal basis. Crandallite has been identified by electron microprobe analyses as a phosphorus numeral in these coals. The authors could quantify calcium, barium, strontium and phosphorus concentrations from the coal attributable to crandallite. These high phosphorus coals provided a unique opportunity to study the association of phosphorus in coals using chemical fractionation for exchangeable cations and acid extractable elements. Since the source of high phosphorous horizons in Cook Inlet coals is attributed to volcanic ash, it is suggested that the profiles of acid extractable phosphorous concentration may be useful for coal seam correlations.

Jan 1, 1992

By Z. Hajnal

Three years ago a research program was initiated at the University of Saskatchewan to develop seismic surveying techniques for use in the Precambrian geological environment. The success of the reflection method in many younger geological settings suggested that this is the technique which would be the most suitable for experimentation. A successful adaptation of this technique to the Shield environment would make mapping of rock formations possible to much greater depth than is possible at the present time with any other applied geophysical technique. This presentation attempts to illustrate the advances which have been made in this program and will provide some insight into future plans. The field investigations were limited to the Flin Flon basin near to the town of Flin Flon, Manitoba (Fig. 1). This area was chosen because the surface geology has been mapped in great detail and it is a very important base metal producing region. It is an ancient sedimentary basin with some characteristics similar to areas where the reflection method has been successful.

Jan 1, 1976

By James J. Brady, Kenneth L. Faught, Chadi El Mohtar, Chaoshi Hu

"During construction of a 9.5-ft. diameter sanitary sewer tunnel, the City of Edmonton encountered a large pocket of flowing sand that flooded their TBM and caused significant surface subsidence, stopping further tunneling by the TBM through this zone. A unique collaborative effort ensued between the authors representing the city, consulting engineers and academic researchers to develop the optimal strategy for grouting the problematic soils. The site has a layer of very find sand between 20 and 30 ft. in depth with fines contents ranging from 5% to more than 40%. The collaboration extended from requesting additional site investigation efforts to shipping samples to the UT-Austin laboratories for grout testing plus ground and grouting characterization tests resulting in field recommendations for a full scale ground improvement program. New research information on the grouting of fine sands along with a collaborative framework for the design of in-situ grouting projects are the key topics presented. INTRODUCTION Encountering a large unexpected pocket of flowing sand with an open-faced TBM while excavating a tunnel below the groundwater table is never a good thing. This was certainly true for the City of Edmonton when one of their Lovat TBM’s became inundated by flowing sand while excavating the 9.5-ft. diameter Millwoods Double Barrel Replacement Tunnel in September 2013. However, since the City of Edmonton self-performed this work, a rare situation existed where the site could be investigated objectively, without the prejudice of contending parties selectively influencing how information was gathered and presented, to accurately examine site conditions with a goal of identifying the best remediation measures."

Jan 1, 2016

By C. J. Toberman

Improvements in fine (28x0) and ultrafine (200x0) coal cleaning is an acknowledged goal with potential benefits in both steam and metallurgical coal markets. This work focuses on adaptation to fine coal flotation of FLOTE, a computer simulation model of the froth flotation process originally developed in the hard minerals field. FLOTE describes the flotation of solids based on particle surface activity, composition, and size. The quasi steady state model was applied to predict flotation performance at an Eastern Kentucky, full scale metallurgical coal preparation plant. Parameter estimation and model testing used detailed flotation test data from a five stage rougher flotation bank. Overall grade/recovery predictions compared well with known plant performance under variation of principally feed grade, plant throughput and reagent addition; however, grade/ recovery predictions for each cell weaken under overloading conditions. Analysis of grade/recovery over a range of sizes is presented. Suggested model improvements and extensions are discussed.

Jan 1, 1984