Search Documents

By R. R. Klimpel

This paper discusses the effect of water chemistry, reagent type, and other environmental factors on the performance of sulfide mineral size reduction and froth flotation processes. Two specific problems will be discussed: 1) the importance of appropriately utilizing the electrochemical window that is created in the grinding process to enhance sulfide mineral recovery by froth flotation; and 2) the impact of steel grinding media versus autogenous grinding on the efficiency of sulfide mineral flotation with varying thiol collectors and water sources.

Jan 1, 1996

By Alan G. Mayton, Jon C. Volkwein

The U.S. Department of the Interior, Bureau of Mines, in cooperation with an American firm, has been contributing toward the creation of a new highwall mining system for extracting coal in active, unreclaimed contour strip mines in the United States. The prototype system features the computer-based, remote control, video operation of a thin-seam continuous miner. Haulage is accomplished remotely also with a 76-m (250-ft) long multiple-unit continuous haulage (MUCH) conveyor system on rubber-tire vehicles. One aspect of this multi-faceted effort has been to design a ventilation system for removing dust generated at the face during the extraction process. The remote mining system eliminates the need for personnel in the mined workings. Ventilation is required to remove visible dust from the area inby two video cameras. These cameras are located approximately 6 m (20 ft) from the face, one on either side of a modified Jeffrey 102HP continuous miner. Removing the dust from this area provides the remote operator with constant visual monitoring of coal extraction at the face and thus, insures the effective operation of the mining system. A ventilation system was designed for use in a mine opening with a maximum cross-sectional area of roughly 4 sq m (44 sq ft) excluding the mining machinery. This paper describes the ventilation system and discusses how it was developed in view of the constraints imposed by the mining equipment, mining conditions, and the extraction process.

Jan 1, 1989

By M. G. Hester

The inadequacy of traditional geostatistical methods for estimating some precious metals deposits has become apparent in the last few years. New methods or estimation such as Indicator, Probability and Multigaussian Kriging are difficult to understand and apply. Case studies using a new method of variogram calculation proposed by Srivastava show the method valuable for variogram estimation in precious metal deposits. Some simple, sometimes unorthodox. estimation methods that have proved useful in Some situations are presented.

Jan 1, 1990

By W. Everett Smith

Factors that have influenced mineralization in the Valley and Ridge and Piedmont provinces in Alabama are not clearly understood. Lithology and structure are recognizable factors in the Valley and Ridge province, where barite, lead, and zinc sulfides occur in structurally complex areas of Cambrian and Ordiovician carbonate rocks. Metal mineralization in the Piedmont province indicates a complex relationship with factors such as favorable host rock, proximity to intrusive or high-grade metamorphic rocks, several metamorphic events and separate or related structural events. Lineaments, as used herein, refer to naturally occurring linear features consisting of topographic, vegetative or soil tonal alignments that are at least partially continuous for distances greater than a mile (Lattman, 1958). Lineaments in Alabama were first recognized by J. G. Newton in 1970, using Apollo 9 series photographs. Subsequent studies delineated the features (Powell and others, 1970) and suggested relationships to structural and hydrologic factors. More recent work has explored relationships to mineralization, environmental geology and the tectonic framework of the Appalachians (Drahovzal and Copeland, 1970; Drahovzal and Neathery, in press). The lineaments recognizable on Apollo 9 photography probably represent fractures, some of which may reflect geofractures that bound major basement blocks. The lineaments defined in Alabama range from about 4 miles to nearly 200 miles in length. Most of the lineaments are straight, but some are arcuate; some appear to terminate at the intersections with other lineaments but most cross each other with no offset. Some lineaments pass through areas of structural disruption such as terminations, offsets and changes in structural style, but others show no such relationships. Most of the lineaments appear to cross topographic features with little or no obvious disruption. Orientation analyses of the lineaments divide them into three directional groupings

Jan 1, 1972

By F. A. Camisani-Calzolari

South Africa has adopted its own code for public reporting of Mineral Resources and Mineral Reserves in 2000. The South African Code for Reporting of Mineral Resources and Mineral Reserves (SAMREC Code or Code) (SAIMM 2000) is presented here in its local and global context. The main aspects of the Code are listed and elaborated upon. The Code has been written with the participation of the major South African stakeholders in the field including Government institutions, the legal confraternity and the mining industry. The Code is modelled on, and is 90% compliant with, the Australasian Code for Reporting of Mineral Resources and Ore Reserves (JORC Code) (AusIMM 1999). The paper also elaborates on the duties and responsibilities of Competent Persons signing off resource and reserve reports and on the listing requirements of the Johannesburg Securities Exchange (JSE), formerly the Johannesburg Stock Exchange, which has officially adopted the Code. The listing requirements were updated in 2000 to incorporate the SAMREC Code and subsequently in 2002, effective 2003. The ongoing obligations of the JSE for the exploration and mining companies are being compiled and are expected to be effective from early 2004.

Jan 1, 2003

By R. B. Hopler

Explosives R&D has historically been motivated by coal mining. Whether to solve safety problems or to improve productivity and cost, the result has been the same: better explosives products and initiation systems. This process continues at an accelerated pace today due to the tools presently available to the explosives and mining industries.

Jan 1, 1993

By R. Adams

Zirconium is the 20th most abundant element in the Earth?s crust and it most often occurs in the form of silicate (as zircon), less often in the oxide form (as baddeleyite or caldesite). Historically, the world?s production of zircon was entirely derived from mining and processing beach sands or heavy mineral sands that were being exploited primarily for their titanium content, i.e., to generate TiO2 feedstocks that would be used for making titanium pigments and, to a lesser extent, titanium metal. Zircon was then regarded as a byproduct, with the sharply fluctuating prices typical of a commodity where the supply is essentially involuntary and not truly responsive to market demand. However, in recent years, zircon has shown considerable mining investment appeal in its own right. Projects have been planned ? and some have already come to fruition ? based mainly on the zircon potential of the deposit. Booming Chinese demand for zircon to meet the requirements of the ceramic and zirconium chemical sectors has been a major factor causing zircon prices (f.o.b. Australia) to surge from US$674/t ($611/st) at [ ] the end of 2005 to beyond US$2,400/t ($2,177/st) by the end of 2011.

Jan 1, 2012

By E Marambio, R Brändle, G Fischer, G von Rickenbach, L Burgos, R Luis Fonseca

Ground support systems must provide safe and effective designs for underground excavations under high stress conditions. These systems must be capable to resist dynamic impacts and yielding during the loading process. In this context dynamic testing of the reinforcement and retaining elements that compose the ground support system are required to study and improve the behaviour of these elements under dynamic load events. During the last years, Geobrugg has been working on the improvement of retaining products by testing them in a large-scale impact test facility located at Walenstadt, Switzerland. The test facility is composed of a double level platform with a square-shaped pyramidal trunk geometry, in the upper level housing a loading mass that drop from a height up to 5m. The loading mass is guided by one central steel pipe, and the impact occurs in the sample to be tested located at the lower level in a slab with an area of 3.6m × 3.6m where the ground support system is installed. During the last years, this innovative facility has been used to test several configurations of ground support systems. The results of these tests have enabled to improve the understating of the behaviour of ground support systems under dynamic loads. In this manuscript, the arrangement, measurement, results, and the preliminary analysis of a single impact dynamic test performed during 2021 of a ground support system with a high-tensile steel wire mesh MINAX 80-4.6 is presented.

Apr 26, 2022

By S. A. Suhler

The detection of hazardous geological anomalies through remote sensing techniques is the subject of current research efforts sponsored by the U.S. Bureau of Mines. In this review, hazardous geological anomalies are discussed with respect to the "view" presented along with potential operational concepts for each technique. The design and development of a borehole radar is described with emphasis on the potential range and resolution capability of the system under realistic underground conditions. Results of field tests at two coal mines and at a hard rock future subway location are presented.

Jan 1, 1978

By I. G. Ediz, D. W. Dixon, W. M. Fidler

In this paper a new method for the arresting of tunnel explosions is presented. In the proposed technique, the on coming explosion is detected by a pressure sensitive device by a pre-determined rise in static pressure. The sensor then triggers a mechanism which causes the explosion door to be closed in a specially constructed concrete barrier zone. The doors are of a special construction and consist of perforated steel plates that allow part of the blast wave to be transmitted but do not allow the passage of the flame. A number of design parameters have been identified, including: the likely amplitudes of the transmitted/reflected pressure waves that would govern the explosion door pressure loading; thickness of the perforated steel packages; perforation dimensions; heat transfer across the door and other factors.

Jan 1, 1995

By A. Haghighat, B. Lattimer

"Mine face ignition due to a high levels of methane is one of the most common fire incidents in underground coal mines. This work exams ignition scenarios in continuous miner headings. Depending on the magnitude of the ignition or resulting fire, the ventilation curtain in the continuous miner (CM) heading may be damaged or dislodged, affecting the ventilation into the area. A computational study was conducted to investigate the effects of different levels of damage to the ventilation curtain on the ventilation flow into the CM area. The computational fluid dynamics software Fire Dynamics Simulator (FDS), Version 6.0 was used to predict the conditions that develop due to a 200 kW fire in the coal mine face following a methane ignition with different levels of curtain damage. Smoke layer depth, temperatures and mass flow into the CM area were used to evaluate the impact of no damage to the curtain, partially dislodged curtain, and fully removed of the curtain. Partial removal of the curtain allowed more smoke to accumulate in the CM area and a reduction in ventilation into the CM area. With full removal of the curtain, the smoke accumulated through the entire depth of the CM area and flowed out the entrance to the CM area and the ventilation completely bypassed the region. INTRODUCTION Active working faces in underground coal mines are one the most hazardous locations in terms of fire events. According to Mine Safety and Health Administration (MSHA) data analysis, the highest number of non-fatal fire incidents was reported at mining faces, intersections and crosscut areas in comparison with other locations from 2000 to 2012. About 464 fires happened at active working faces from 2000 to 2012, most consisting of a methane ignition, in some cases followed by localized fire. These are high risk incidents due to the potential to raise float dust and damage ventilation systems, particularly auxiliary systems such as curtain or tubing. Depending on the magnitude of the ignition or fire, the ventilation curtain in the continuous miner (CM) area may be damaged or dislodged, affecting the ventilation into the area. Five computational fluid dynamics (CFD) scenarios were considered to investigate the smoke layer depth, temperature, visibility, mass flow rate, and the behavior of airflow in an entry with a continuous miner (CM) located in it. The state of the auxiliary ventilation was varied based on the assumption that as an ignition increases it magnitude it will affect ventilation curtain proportionally. Visibility and temperature along the height of the entry at different sections were investigated and the interface height at each section was determined. Also, the fresh air height was studied for tenability analysis in future. FDS, Version 6.0 was used to predict the conditions that develop due to a 200 kW fire on the coal mine face following a methane ignition with different levels of curtain damage. Smoke view software was used as the post processor to visualize and analyze methane fire behavior at the face. Most entry fires are reported as fuel-controlled fires as they are rarely restricted to air access (Ingason et al, 2014). The working face fire in the following models was assumed to be a fuel-controlled fire."

Jan 1, 2016

By M. J. Scoble

There is no straightforward and systematic method for adequately measuring blast damage in on-going mining operations. This paper considers various techniques available for the measurement of blast damage, making particular reference to recent underground hardrock mine studies. This paper concludes by indicating the importance of understanding and accounting for geology and emphasizes the need for a robust damage-audit procedure.

Jan 1, 1997

By L. O’Connor, E. Tarshizi

The objective of this work is to provide a detailed review and a list of references in chronological order, comprising 80 recent technical papers, on the use of discrete-event simulation (DES) modeling in mining engineering. In this article, the review papers of published mine simulation projects through 2007 are summarized, and then a comprehensive review of individual articles published from 2008 to 2015 is presented. This survey work also includes analyses of the simulation tools used in the published projects, mining types and applications in order to assess these key features and evaluate the recent state of research in mine DES simulation. In addition, an interactive map visualization for the locations of the simulated projects is made available on a website to benefit current and prospective scholars in the field. The results of this investigation revealed that the most common application of DES in mining had been mining equipment selection and analysis, while ore processing and risk management projects were less frequently reported. The results also showed that modeling surface mines were in the majority, but the trend of publications for underground mine simulations had also increased. According to the results, ARENA was the most popular simulation software package, but several simulation tools that were only used once or twice in the mining projects are also included in this review.

Jan 1, 2018

By L. O’Connor, E. Tarshizi

The objective of this work is to provide a detailed review and a list of references in chronological order, comprising 80 recent technical papers, on the use of discrete-event simulation (DES) modeling in mining engineering. In this article, the review papers of published mine simulation projects through 2007 are summarized, and then a comprehensive review of individual articles published from 2008 to 2015 is presented. This survey work also includes analyses of the simulation tools used in the published projects, mining types and applications in order to assess these key features and evaluate the recent state of research in mine DES simulation. In addition, an interactive map visualization for the locations of the simulated projects is made available on a website to benefit current and prospective scholars in the field. The results of this investigation revealed that the most common application of DES in mining had been mining equipment selection and analysis, while ore processing and risk management projects were less frequently reported. The results also showed that modeling surface mines were in the majority, but the trend of publications for underground mine simulations had also increased. According to the results, ARENA was the most popular simulation software package, but several simulation tools that were only used once or twice in the mining projects are also included in this review.

Jan 1, 2017

By Shuang Shuang Huang, John Fillos

Ozonation was evaluated as an alternative treatment process for leachates of municipal landfills. The study was carried out on leachate from the Fresh Kills Landfill, New York City. The leachate has strong tea color and BOD5 ranging between 90 mg/L and 130 mg/L. The average COD, TOC and NH3-N concentrations were 1800 mg/L , 550 mg/L, and 665 mg/L, respectively. The kinetics of the process were studied in a sparged batch reactor by developing concentration- time profiles for residual color and TOC. Continuous flow experiments were then carried out at two selected contact times. The process was found to be effective in the treatment of leachates for color and TOC removal.

Jan 1, 1992

By L. G. Austin

Development of an equation for tumbling charge and balls plus comparison to plant data suggests that the net mill power for cylindrical semiautogenous mills can be calculated from

Jan 1, 1991

By Ellis G. Goree, George A. Simmons, Andrew B. Pervis

The pneumatic classifiers are widely used for fine dry powders separation These classifiers can be used for either the removal of fines from coarse feeds or the removal of coarse particles from ultrafine feed To optimize the operation of pneumatic classifiers, a thorough understanding of the impact of operational parameters on the efficiency of classification is essential This paper describes the design features and effects of operational parameters followed by illustrations of pneumatic classifiers usage in two case studies

Jan 1, 1983

By Shannon Seitz, Qingwen Shi, Junfeng Pan, Shuwen Wang, Brijes Mishra, Shaohong Liu

Delayed coal bursts in deep coal mines have caused significant fatalities and economic losses in recent years. Instead of occurring right around the advancing face, this particular type of coal burst is characterized by its occurrence at a certain distance behind the advancing face. To better understand the mechanism of a delayed coal burst, we used borehole camera, electromagnetic CT, and borehole deformation monitoring device to observe the fracturing and deformation process of an advancing entry’s surrounding coal in the field. Borehole camera detection showed a zonal disintegration phenomenon in the advancing entry’s surrounding coal. Electromagnetic CT detection showed that zonal disintegration developed within 14 days of excavation. Borehole deformation monitoring indicated a deformation rate difference between the intact zone and fractured zones. The deformation rate difference was observed to increase with time and cause increasing elastic energy accumulation in the intact zone. The cumulative elastic energy in the intact zone finally caused a delayed coal burst in the entry. Sensitivity analysis of the cumulative elastic energy was conducted based on a thick-walled model deduced from field detection. The model shows that the smaller thickness of the intact zone brings higher elastic energy in the intact zone. This investigation provides an improved understanding of delayed coal bursts in deep coal mines.

Oct 19, 2021

By P. K. Sims

One-day field trip via U.S. Highway 6 and Colorado Highways 119 and 279 from Golden, Colorado to Idaho Springs. This field trip provides an opportunity to observe aspects of the Laramide ore deposits in the Central City and Idaho Springs mining districts and the Proterozoic basement rocks, which host the ore deposits.

Jan 1, 1986

By Steve Karl

Introduction US steel production dropped 5% in 1985 to 79 Mt (87 million st). US operators are producing at only about 65% of capacity. More than 600 steelmaking facilities have closed in just 10 years. And McDonalds Corp. now employs more people than the entire US steel industry's 200,000. Not gloomy enough? Well, the North American iron ore industry can expect more plant closures and capacity reductions in the coming years. And don't count on the Federal government's voluntary restraint agreements with foreign steel producers to bail out the industry. In 1985, the first full year of the restraint agreements program, steel imports were more than 25% of domestic consumption, well above the 18.5% target. That's the grim truth, according to M. A. Hanna's Robert F. Anderson. Hanna's chairman was speaking to a group of iron ore, taconite, and steel industry executives at the Minnesota Section AIME meeting in Duluth in January. Despite those depressing facts, Anderson said he believes the domestic iron ore and steel industries can survive, although they will both be shadows of their former selves. But, he is giving them five years to make the necessary adjustments or both will die. Major steel producers during the last four years have added about $7 billion in losses to their books, he said. In Minnesota's Iron Range, employment in iron ore and taconite has gone from 14,000 10 years ago to less than half that today. Anderson explained that steel producers have more capacity today that more than meets their demand for iron ore. This places great pressure on iron ore producers to restructure to survive. Hanna, for example, has been forced to close or divest its iron ore interests in Missouri, Michigan, Canada, and Minnesota since 1980. The latest casualty was the company's Butler taconite project in Minnesota. "In just five years we've reduced ownership of active pellet capacity by 80%," he said. Technological ironies Improved technology is one cause of the industry's woes, Anderson said. While these improvements are welcome in terms of remaining competitive, the irony is that some of these technological improvements are coming at the expense of the iron and steel industries. There is a growing demand for lighter and less expensive substitutes for steel. Automobiles contain about 318 kg (700 lbs) less steel than they did 10 years ago. And, Anderson said Ford Motor Co. has indicated it plans to reduce steel usage an average of 50 kg (112 lbs) per car in the next few years. One leading steel analyst has predicted that steel usage in cars will fall another 40% in the coming years. Improved steelmaking technology has also decreased raw steel production. Continuous casting is more efficient than traditional forms of steelmaking, Anderson said. Continuous casting accounted for about 43% of steel production in the US last year, compared to 9% a decade earlier. And, Japan and Korea are producing more

Jan 3, 1986