Search Documents

By Harlan N. Barton

A commercially available portable X-ray spectrograph, lightweight and of rugged construction for vehicle or field camp use, was used for the determination of Ba, Cu, Fe, Mn, Pb, Rb, Sr, and Zn in stream sediment geo- chemical samples. Investigations showed a relative standard deviation of 1-3 percent, detection limits of approximately 100 ppm; and significant matrix effects. Coefficients of correlation greater than 0.9 were obtained between portable X-ray and emission and atomic- absorption spectroscopy analyses. A geochemical map of a known mineralized area showed good agreement with maps prepared by other methods of analysis and sample media.

Jan 1, 1980

By Joseph Matoney, B. K. Parekh

INTRODUCTION The term "dewatering" refers to removal of water from coal. Water associated with coal can be categorized as "free or surface" and "inherent or chemically bound" moisture.' The free moisture is found on the surface of coal, in capillaries and small spaces between two or more particles. The inherent or chemically bound water is found in the interior of the coal and as part of coal structure. A significant amount of free moisture can be removed by mechanical dewatering techniques. However, inherent moisture can only be removed by applying energy intensive techniques, e.g., direct or indirect heating. Moisture in the coal offsets some of the benefits of coal cleaning. Extra water in clean coal adds to extra cost in transportation, heat lost during vaporization, and plugging of chutes. From a utility perspective, a 1 % increase in moisture can offset a 4.5% decrease in ash.2 Mechanical dewatering can be classified into two major process categories according to the principles involved, namely, 1. Sedimentation-liquid is constrained and particles move freely. 2. Filtration-particles are constrained by a medium and the liquid flows through. Each of the process categories is composed of various separation techniques shown in Fig. Equipment currently being used by the mechanical dewatering of coal of varying size ranges and final moisture content is illustrated in Fig. 8-2. This figure indicates that sizes larger than 13/, in. (37.5 mm) present no particular dewatering problem. Shaker screens of the very crudest types and designs are capable of producing these sizes at low surface moistures. High-speed vibrators are used for the intermediate sizes and can be used for smaller sizes down to 0.02 in. (0.5 mm) if high moistures (15% surface moisture or greater) can be tolerated in the product. Usually, however, the vibrator is not used below 3/, to 3/, in. (9.5 to 6.3 mm) because of the moisture associated with these fine sizes. At this level, centrifugal force is usually employed to aid dewatering. Centrifuges of various types and designs are used practically

Jan 1, 1991

By A. K. Bakshi

An on-line rheometer, suitable for use with slurries, has been developed at Michigan Technological University. This rheometer can be used with both Newtonian and non-Newtonian slurries, and produces complete shear-rate/shear stress curves which characterize the time-independent rheology of the slurry. The sensor utilizes the Hagen-Poiseuille equation and Boyle's Law to calculate the shear rate, slurry flowrate, and shear stress from a series of pressure measurements. The design of the unit allows the measurement sample to be continuously collected from operating process streams in the often-hostile on-line environment. The shear rate/shear stress curves can be used to conveniently calculate the apparent viscosity at any given shear rate, and also to measure any yield stress or other deviations from Newtonian behavior.

Jan 1, 1999

By S. J. Schatzel, J. D. Addis, V. Gangrade, L. L. Chasko, C. A. Hollerich

"A ventilation study using tracer gas was conducted at a western US coal mine. The objective of the study was to evaluate the movement of longwall face air exchanges between the face and worked-out area and to document the presence or absence of face airflow pathways between these locations. The mine operator uses a bleederless longwall ventilation system with a back return and a blowing mine ventilation system. The study was conducted on an active panel and included both underground and surface monitoring sites. The study used sulfur hexafluoride (SF6) released as a slug on the longwall face and in the front of the gob inby the face. The velocity of the tracer gas movement in the gob was 0.019 m/s (3.7 fpm). The rate of movement for the overall tracer gas slug averaged about 0.0091 m/s (1.8 fpm). A separate tracer gas test initiated with the release of SF6 into the legs of the first shield showed the existence of more than one pathway of face air in the general direction from the headgate towards the tailgate corner. Maintaining adequate ventilation air on longwall faces is important for worker safety and for the dilution of methane emitted from the face and caved gob. A more detailed characterization of longwall system air and gas movement allows a mine to better assess its ventilation design for controlling gas on the face and in the gob. INTRODUCTION During a series of stakeholder meetings, a near unanimous concern was expressed related to maintenance of effective ventilation airflow on longwall faces. There was a strong interest expressed regarding the impacts of face length and caving characteristics on the ability to maintain adequate face airflow levels. This study seeks to understand and improve a mine operator’s ability to monitor and control ventilation and methane concentrations across the longwall face by assessing airflow variations in terms of roof caving characteristics and face length. National Institute for Occupational Safety and Health (NIOSH) researchers seek to identify flow paths of ventilation airflow on longwall panels with variations in roof caving characteristics and longwall face lengths. The project research aims to develop an understanding of the role of gas dynamics in variable broken rock, interactions with ventilation airflow and methane concentrations across the longwall face area. The research also addresses continuous ventilation monitoring along the shield line to provide early detection of gas exchanges between face and gob, and thus improve a mine operator’s ability to monitor and control ventilation and methane concentrations around the face. In the context of this paper, the longwall gob refers to the pillared area behind the shields. This work reports on results from one project task to conduct field based research using a tracer gas to describe face air and gob area gas movement in a bleederless longwall ventilation system that incorporated a back return."

Jan 1, 2017

By Jerry L. Fuller

Fan performance graphs are generated by digital computer using two programs, RUN- FANS and FANPLOT. RUNFANS calculates fan performance data from stored specific-volume, specific-speed data for a given fan type with appropriate allowances for fan diameter, rotational speed and air density. FANPLOT accepts specifications for drawing the graph and accepts either user-supplied pressure-quantity data or RUNFANS- calculated data as input, Operational procedures for both programs are detailed and examples of their interactive query routines are included. The hardware necessary to generate the graphs is illustrated. Several hardcopy output options are discussed,

Jan 1, 1984

By P. Somasundaran, J. T. Kunjappu

Spectroscopic techniques are becoming increasingly popular for characterizing the interior of adsorbed layers of surfactants and polymers at solid- liquid interface as well as in the identification of com- pounds on mineral surfaces. This review encompasses the application of fluorescence and ESR spectroscopic techniques to reveal the microscopic environment of the adsorbed layers of surfactants and polymers on minerals with a special reference to the adsorption of anionic surfactants (e.g., sodium dodecyl sulfate) and polyelectrolytes (e.g., polyacrylic acid) at positively charged mineral (e.g., alumina) - water interfaces. Finally, the utility of XPS and auger techniques to identify the surface elemental composition of different mineral species has been related to their flotation efficiency.

Jan 1, 1987

By Y. Xi

In this paper we present an availability approach for determining the capacity of a major bucket wheel excavator (BWE) system to be used in Yuabaoshan surface coal mine in China. Based on previous time studies on other BWE systems for delay times due to internal and external causes, and a four-level maintenance and repair schedule, we develop a model taking into account all random failures and present a fast and simple solution to this highly complex problem. A procedure employing the Markov renewal theory for determination of the distribution of random failure times and failure rate of the whole system, as well as some other factors useful for calculation of the overall system capacity are discussed in the paper.

Jan 1, 1993

By Otis M. Clarke

Observations of the land surface show that subsidence over active and abandoned underground mines is controlled to some extent by the stratigraphic and structural geology of the mines in addition to the methods of mining and the thickness of the seam mined. Exposures in highwalls of surface mines that intersect abandoned underground mines in the Warrior coal basin of Alabama illustrate this, showing sandstone beds that act as beams bridging openings and interbedded shale beds crumbling. Stratigraphic changes observed in the district are extremely variable and calculations regarding subsidence used for one area will not apply to another area if there is a major change in rock types Rocks exposed in road cuts and open pit mines demonstrate a marked difference in weathering characteristics. Some rocks, such as shale, wea- ther very rapidly, by crumbling and becoming plastic, whereas other rocks, such as sandstone, resist weathering. The continuing rock weathering after mining in openings produced by the mining activity and in fractures caused by roof movement, apparently, is a major cause of the surface sub- sidence that may occur years after the mines are abandoned.

Jan 1, 1986

By S. A. Matthews, M. L. Nave

AC variable frequency motor drives are emerging technology for belt conveyors. The success of the application in mining depends on adequate and timely consideration of drive, motor, and conveyor features. The purpose of this paper is to familiarize and inform possible mining users of AC variable frequency drive attributes.

Jan 1, 1998

By H. Askari-Nasab, B. Osei, K. Awuah-Offei

The U.S. coal mining industry consumes approximately 142 billion kWh/a of energy. The U.S. Department of Energy estimates that the industry’s annual energy consumption could be reduced by 49%. This constitutes nearly $3.7 billion of potential savings on coal production costs at 5.3¢/kWh of energy. Additionally, with climate change regulation on the horizon, any benefits from energy savings in the near future are compounded by associated reductions in CO2 emissions. Research indicates that operating conditions significantly affect energy efficiency. Modeling and simulation have been shown to be a cheap and reliable means of evaluating the effects of process interactions and operating conditions. The goal of this work was to apply stochastic process simulation to model the energy efficiency of a typical truck-and-shovel mining system and use the model to evaluate production strategies to improve energy efficiency. The research team conducted energy audits of truck-and-shovel overburden removal and used the results to develop regression models describing truck and shovel fuel consumption. The team then built a stochastic simulation model of the truck-and-shovel overburden removal operation and used it to assess a variety of improvement measures by simulation experimentation. Valid fuel consumption models for shovel loading and truck haulage have been formulated, based on the energy audit results. Valid stochastic process models of truck-and-shovel operations have been formulated to study energy efficiency. The following strategies, in decreasing order of impact, provide the most energy savings for truck-and-shovel overburden removal at the mine: (1) shorten haul roads, (2) increase shovel capacity and (3) increase shovel utilization through optimal truck matching. Additional data will be required to adequately describe operator effects on energy efficiency.

Jan 1, 2011

By Donald W. Gentry

Mine valuation is a multifaceted, interdisciplinary process by which the economic viability of an old, existing, or new mining property or venture is determined. The problems associated with arriving at a representative and accurate value for a mining property are complex and numerous, and the procedures utilized in determining these values vary from simple, back-of-envelope calculations to sophisticated mathematical manipulations requiring computer modeling and analysis. Regardless of the complexity or the degree of sophistication associated with any particular project, the evaluation process must ultimately provide management with two basic types of information. First, the evaluation process should indicate whether or not the mining project is economically viable after careful consideration of all engineering, environmental, geologic, and other variables pertaining to the project. Second, the evaluation process should provide management in- formation on the relative attractiveness of the project when compared to other alternatives. In some cases, it may be extremely difficult to supply this information for a project directly. Nonetheless, the evaluation process should and must present all information necessary in a format which can be incorporated into the decision-making process as expeditiously as possible.

Jan 1, 1979

By Frank Palkovits

All technologies move through a cycle from infancy to maturity. Thickened tailings have moved into the young adulthood phase of its development. Many mining companies like the idea of reducing their water-taking and water disposal issues. This limits the risks associated with traditional surface water-covered tailings facilities and the reduced dilution possible through underground disposal of thickened or paste tailings. Just as home theater systems advertised as ?plug and play? are rarely quite that straightforward, implementing and improving a thickened-tailings system has its challenges. However, the technology has also developed in recent years so it is more accessible. Some success factors have emerged because of the new technologies. Is thickened tailings the right solution? The first step in success with thickened tailings should be whether it is, in fact, the right solution for a particular mine. And, if so, what type of thickening is best. The answer depends on several factors, including: ? Grain size: The grain size that is optimal for maximizing mill recovery is some-times not suitable for thickening. Other mineralogical factors, such as mica content, may also influence whether the tailings are suitable. ? Water issues: Available water does not always have the purity necessary for the process. Another issue to consider is that if water is in short supply, as is increasingly often the case, thickening may be a way to reduce the need to both take and dispose of water.

Jan 1, 2008

By C. Stephan, E. Weiss, J. Trackemas, M. Sapko

The National Institute for Occupational Safety and Health (NIOSH), Pittsburgh Research Laboratory (PRL), in collaboration with the Mine Safety and Health Administration (MSHA), the mining industry, and seal manufacturers recently conducted a series of full-scale experiments within the underground experimental mine at PRL’s Lake Lynn Laboratory. The purpose of the experiments was to evaluate the explosion-resistant characteristics of several new seal designs for rapid deployment during mine emergencies. These seals can be deployed in 6 to 10 hr and are capable of withstanding explosion overpressures in excess of 140 kPa (20 psi). These novel seal designs use available mine materials, do not require conventional rib hitching, and, most importantly, can substantially reduce exposure time for coal miners during sealing and mine recovery operations.

Jan 1, 2003

By V. Svalbonas, S. M. Jones, A. Boughey

In June 1998, the world's largest grinding mill, the 40 ft (12.2 m) diameter 20 MW Cadia gearless SAG mill, was commissioned. This was a leap of over40% above the largest operating SAG mill. A significant saving in capital cost gave the incentive necessary for a single mill line at Cadia, resulting in the selection of the 40 ft (12.2 m) diameter mill. Now, after 18 months of operation, this paper will review the significant items involved in the development, design, manufacture, installation, and operation of this mill.

Jan 1, 2000

By George J. Allen, Laura A. Allen

Introduction This section of the text presents a general review of the different types of concentrate marketing contracts. Too often the marketing strategy is ignored in the design phase of the project and the producer is left to the mercy of the buyer. Many items such as concentrate grade, impurity levels and moisture content of the concentrate my enhance, or severely restrict the producers ability to make a profit it. Close attention should be paid to the design of the concentrator which can improve the quality of the concentrates, thus the ability to increase the rider of potential buyers can be enhanced. Difficult at best, is the position of the miner who only has one outlet available for its production. Obviously, the trade offs must be evaluated. For example, concentrate grade vs recovery and grind/filtering capacity vs moisture of the concentrate all must be weighted against freight cost to a potential buyer. In addition, the above considerations must be weighed against the capital cost to the miner. This chapter is intended to highlight important articles that are included in short and long term agreements and to give a new miner/producer some insight into hat my or my not add value to the product. Unless the miner sells the product directly to a consumer such as a gold, or silver producer, or to a large enough operation that has a totally intergrated system to make a finished product, most miners are forced to sell to buyers who ultimately will refine and market the product. Types of Contract Agreements There are many types of contract agreements just as there are colors in the rainbow, however, most contracts fall into three basic categories. (1) Smelter Schedules: Designed for the small producer, the odd lot of concentrate, smelter flux and precious metal ore. Albeit custom smelters are becoming fever by the day, because of pollution control requirements and financial difficulties, most remaining custom smelters have a smelter schedule. A smelter schedule is a posted list of charges and conditions that the smelter will buy material from a seller. Smelter schedules exist for copper, lead, zinc, silver and gold (Handbook for Small Mining Enterprises, Montana Bureau of Mines). (2) Short Term Custom Contracts: Large mine producers frequently use Short Term Contracts where the seller has the buyer frame a contract that is tailored to the sellers’ production. The short term contract my be as long as one year. A spot sale qualifes as a

Jan 1, 1986

By R. L. Morse

The thermodynamic program is similar to previous mine ventilation programs but has been expanded to consider the compressibility of air. The thermodynamic program does consider: 1) air density variations, 2) humidity changes, 3) intake, exhaust, and underground fans, 4) heat transfer between rock and air, 5) refrigeration of heating plants, both surface and underground, and 6) heat generated by equipment, both diesel and electric. 110st of the compressibility factors are handled in the branch calculations. The field survey necessary to supply-data for this program is quite similar to the basic base and leap-frog pair of stations method used with most incompressible mine ventilation programs. The thermodynamic program is a complete package of ventilation network analysis which can provide mine management with good operational control and planning of mine ventilation systems.

Jan 1, 1977

By T. W. West

INTRODUCTION This paper presents an assessment of conventional flotation technology. In addition it presents some ideas which can be used to change the perception of what may be done with conventional flotation equipment to maximize its efficiency. Perspective of Conventional Flotation Technology 1. Flotation in many coal preparation plants is defined as something between a necessary evil and a non-viable concept because: -Too much art is required on a continuous basis to achieve uniformly acceptable results. -It is expensive, the capital cost in dollars per ton of circuit feed for flotation and dewatering is high. -It is a difficult process to use when SO2 reduction governs system design and equipment selection. -It creates a product (fine coal froth) that is difficult to dewater in the presence of BTU/lb as-received pressures. -It is a difficult process to control from a management standpoint, there are no dependable set points to rely on. 2. Many froth cell circuits are 0.5m x 0 (nominal 28 M x 0) feed which is sourced from screen/cyclone underflows. The original intent was to obtain maximum yield at acceptable product quality and moisture using disc filters. (See Figure #1) 3. An alternate to conventional flotation and its perceived to be limits of efficiency, capital costs, etc. is to move towards such developing flotation technologies as column flotation, reverse flotation, and microbubbles. A lot of work is being done to move these concepts thru pilot stages into full scale, commercial plant operation. The majority of the coal producers and coal preparation plant designers view these concepts as being in the development/pilot plant stages. OBJECTIVES Based on the preceeding comments of the perspectives of the coal producers and plant designers, the options are limited. They can make do with what they have available to them in the way of industry standard equipment and practices or they can move forward with developing technology. I feel there is a third option: what can we really do today with what is available to us, without reinventing the wheel? APPROACH 1. When processing coal against ash and SO2 restrictions, the fine clean coal stream can be the best stream on the clean coal conveyor due to the release by size and the ability to create a high BTU/low sulfur (dry basis) product. 2. Targets: -Consistent raw coal size consist in the plant feed . -Do not put pyrites in the froth cells. -Adjust criteria defining good flotation away from yield towards maximum BTU recovery at minimum ash. -Limit the froth cell feed size consist to 0.15 mm x 0 (nominal 100M x 0). -Establish and maintain a correct, consistent percent solids in the froth cell feed. -Select flotation reagents with care. -Introduce reagents in the proper sequence.

Jan 1, 1988

By R. L. Miller

Two samples of iron enriched basalt (IEB) containing simulated nuclear fuel and having two distinct microstructures were prepared and tested for uranium recovery. The IEBs are refractory towards leaching by ground water. However, the uranium content (15.8%) is high enough that if aggressive leaching techniques are used for uranium recovery, these materials could be considered as man-made uranium ores. The IEBs discussed in this report were prepared to simulate Three Mile Island-2 core debris. The crushed IEBs were treated using three different methods simulating potential industrial scale processes. In one method the IEBs were fused with sodium hydroxide then the cooled mass leached first with water then with dilute sulfuric acid; about 52% of the uranium was recovered in this case. In the second method the IEBs were treated with a sulfuric acid/hydrogen peroxide lixiviant and about 13% of the uranium was recovered. In the third technique the IEBs were leached with a sodium carbonate/sodium bicarbonate/hydrogen peroxide solution. Only about 0.1% of the uranium was recovered. The results of these screening tests suggest that the IEBs can be successfully treated for recovery of the contained uranium. Other studies would be required to determine if other values, such as zirconium or silver, could be recovered from the IEBs.

Jan 1, 1984

By M. Robb, S. J. Bate, M. Boisvert

The never-ending quest for gold-bearing ore deposits is a primary industry in Canada, employing people of widely differing expertise. The exploration models for gold deposits are generally geologically complex and the targets have relatively small cross-sectional areas. These problems are compounded in Canada by the minimal outcrop exposure in most mineral provinces and the high percentage of water-covered areas. Naturally the chances of successfully delineating an economic gold deposit are very much greater if all parties involved can act as a team of explorationists constantly confemng amongst themselves particularly as the applicable disciplines generally overlap and complement each other. Three case histories (see Figure 1) are presented to illustrate this philosophy with emphasis placed on the role of the geophysicist in translating the exploration model as defined by the geologist into physically measurable parameters and identifying target areas with similar characteristics. The Conwest-Miminiska property in Ontario is a grassroots exploration play. Additional ore reserves needed to be delineated on the Salmita property in the Northwest Territories. At Laura Lake, near Chapais, Quebec geophysical methods were employed to trace thin high-grade mineral intersections under deep overburden and severe cultural interference.

Jan 1, 1989

By C. H. Cox

The Alumet Company of Golden, Colorado, is currently engaged in the development of their Diamond Creek and Lanes Creek phosphate ore bodies located near Soda Springs, Idaho. The Alumet Company is a partnership of National Steel, Southwire Co., and Earth Science Inc. Davy Powergas, Inc., of Florida was contracted by Alumet to perform an evaluation study of these properties and, in general, determine the tonnage of altered and unaltered phosphate reserves which would be amenable to beneficiation and production of merchantable phosphate rock (defined as material with a P2O5 content of 3 1.0% and greater). The Colorado School of Mines Research Institute was retained by Davy Powergas to develop a beneficiation method for the studies of the altered and unaltered ores. Ore reserves were classified by Davy in a comprehensive range of categories such that any partial grouping could be made as dictated by future mine planning, mine or mill design, or prevalent economic conditions. Categories included ore horizon, stripping ratio, degree of certainty of their existence, and physical and chemical characteristics. The last category was of interest for beneficiation considerations in that it dealt with the degree of alteration of the phosphate ore.

Jan 1, 1979