Search Documents

By G. Kritikakis

Rehabilitation of sites contaminated by oil products and chlorinated organic compounds is a costly task which affects the planning of urban and infrastructure development. An integrated approach based on the non-invasive geophysical technology is utilized for subsurface characterization of contaminated land. In this approach the localized information, provided by chemical analysis of soil samples collected from bore-holes, is used for the calibration of the geophysical data. This information is subsequently extrapolated to the area under investigation by combining it with the geophysical results, providing thus information about pollution accumulation, contaminants? flow and pollution sources. Two case studies are presented from sites contaminated by heavy metals (Venice, Italy) and oil products (Athens, Greece). Resistivity, electromagnetic and seismic methods were used in this approach. Namely, electrical tomography, electromagnetic mapping, ground penetrating radar (GPR), multichannel analysis of surface waves (MASW) and seismic refraction experiments were conducted. In Italy, the sections from the multichannel analysis of surface waves imaged successfully a buried channel where the pollution is concentrated. Preliminary results are also discussed from the geophysical survey in Greece where the thickness of the oil phase located on top of the water layer is 60 cm.

Jan 1, 2006

By Fathi Habashi

OXIDE ORES can be divided into two groups: 1) Simple oxides (Table 3.1). 2) Complex oxides. Those ores containing minerals composed of two oxides; an acid oxide (Cr2O3, Nb2O5, etc.), and a basic oxide (CaO, FeO, MnO), as shown in Table 3.2.

Jan 1, 1970

By Gregg Wilkerson

The Blind Springs Hill pumice beds are located 5 miles southwest of Benton, California in the foothills between the Benton Mountain Range and Blind Springs Valley. The best exposures of the pumice are in an area 0.75 miles west of Blind Springs Hill. The pumice is Quaternary ejecta material which came from the rhyolitic volcanoes in the Glass Mountain-Volcanic Tablelands area of Mono County. The pumice beds occur in two distinct layers separated by an unconformity. The upper layer is 0 to 11 feet thick and consists of coarse subangular pumice fragments, some of which are over 1.75 inches in diameter. The lower bed is medium to coarse grained with subangular fragments up to 1.0 inch. The lower bed is 0 to 9 feet thick. Overburden at the Blind Springs Hill deposit varies from 0 to 15 feet. There are approximately 1 million cubic yards of material in the deposit that can be mined. The size distribution in the deposit is mostly fine with only 10.6% of the pumice fragments being over 0.5 inch in diameter, the minimum size needed for stone-wash or acid-wash applications. Suitability of pumice for the textile industry is quantified by standard 15-minute abrasion and absorption tests. In the Blind Springs Hill deposit, the plus 0.5 inch fraction has an abrasion loss of 33% which is too high for stone-wash application but it has an absorption capacity of 36% which makes it suitable for acid-wash applications in the textile industry. The abrasion and absorption properties of this deposit are within the range of those which have been measured for other pumice deposits within the United States.

Jan 1, 1995

By F. Calizaya

This study summarizes the ventilation requirements for a highly mechanized P.T.Freeport Indonesia's underground mine operation in Irian Jaya, Indonesia. The Deep Ore Zone (DOZ) is a copper-gold deposit being developed underneath the current Intermediate Ore Zone (IOZ) mine. One of company's current plans is to prepare this mine for a steady oreflow of 25,000 tpd by year 2003. This study includes the estimation of airflow requirements for various mining activities, the design of major intakes and returns, the determination of airway resistances and specifications of fan duties. It also includes the results of air pressure/quantity measurements in existing airways and the standards stated by the current Indonesian mining law.

Jan 1, 1998

By Lauren W. Choate

Wollastonite, a calcium metasilicate, derives its name from the man who discovered the mineral, Doctor William H. Wollaston, an English scientist. OCCURENCE Occurences of the mineral have been noted in Finland, Switzerland, Russia, Japan, Mexico and in the United States in Texas, California, Arizona, and New York. The only commercial deposit now being exploited is at Willsboro, New York. It is mined and processed by the Cabot Corporation whose home offices are in Boston, Massachusetts.

Jan 1, 1964

By A. S. Malicsi, Vathsala Rajagopal, I. Iwasaki

Corrosion and abrasion properties of a series of chromium-containing, cast-iron balls, with Cr contents ranging from 0% to 29%, were evaluated and compared with austenitic stainless-steel and mild-steel balls. Marked ball wear tests were performed on artificial ore samples consisting of 95% quartzite, with either 5% pyrrhotite or 5% chalcopyrite, under a nitrogen or oxygen atmosphere. The electrochemical mechanism was investigated by correlating the corrosive wear with the corrosion currents obtained from potentiodynantic polarization curves under abrasion. Flotation recoveries were determined on a 95% quartzite + 5% pyrrhotite sample ground with various cast-iron ball materials under an oxygen or nitrogen atmosphere. Electrochemical results are found to be in good agreement with flotation results and with corrosive wear data obtained from marked ball wear tests.

Jan 1, 1993

By G. J. Simandl

Jade is a commercial term encompassing green, white, black or yellow-brown jadeitite and nephrite. Jadeitite consists of Na-rich pyroxene, whereas nephrite consists of prismatic to acicular amphiboles of the tremolite-actinolite series forming bundles that are randomly oriented and interlocked. Nephrite is tougher (harder to break) than jadeitite. Its fracture strength is about 200 MN/m2 whereas that of jadeitite is about 100 MN/m2. On the other hand, jadeitite has a higher hardness (7 compared to 6.5 on the Mohs scale). There are over fifty known nephrite occurrences in British Columbia (B.C.). These occurrences consist of individual blocks, boulder fields, talus blocks and in situ occurrences. Most of the in situ occurrences are lens or cigar shaped. They occur at, or near the contact of ultramafic/mafic rocks (mainly serpentinites) with cherts, and other metasedimentary or igneous felsic rocks of Mississippian to Jurassic oceanic terranes such as Cache Creek and Slide Mountain. These contacts are commonly interpreted as shear/fault related. In general, it is believed that the B.C. nephrite formed by metasomatic exchange between ultramafic and silica-bearing rocks. Impurities in B.C. nephrite are spinel group minerals (chromite, magnetite, picolite), diopside, uvarovite, titanite, chlorite, and talc. Jadeitite is slightly denser than nephrite and good quality material sinks in methyl iodine. There are no known jadeitite occurrences of economic interest in B.C., but there are at least four geographic areas where favorable lithologies, and metamorphic conditions (Pn) required for the formation of jadeitite coincide. These are Bridge River, Pinchi Lake, Dease Lake, and Jennings River. These areas are known to contain small concentrations of jadeite, or are characterized by blueschist or eclogite-grade metamorphic conditions. Rhodonite and pyroxmangite are MnSi03 polymorphs. These minerals are pyroxenoids and are macroscopically and microscopically very similar. For brevity, both are grouped together under the term "rhodonite". Most of the B.C. occurrences are hosted by late Paleozoic chert sequences and are lens shaped and concordant. The common association of rhodonite with iron formations, jasperoids, and/or volcanogenic sulphide deposits in southwestern B.C. permits the delineation of favorable horizons using magnetic or electro-magnetic geophysical methods. Geographic associations between manganese showings and sulphide deposits, and the hydrothermal chemical signature of the rhodonite occurrences from this area, suggest a genetic link between rhodonite and volcanogenic sulphide deposits. The typical rhodonite rocks consist of rhodonite, pyroxmangite, neotocite, black amorphous Mn-oxides, Mn-bearing garnet, ± epidote, ±chlorite, ±rhodochrosite, ± parakutnah-orite, ± Mn-bearing calcite, ± iron oxides and hydroxides. Garnet ± epidote forms yellow patches and layers within the rhodonite. Within some of the rhodonite occurrences, the garnet is altered to chlorite. Rhodonite-bearing rock is commonly cross cut by secondary manganese oxide veins, creating a characteristic web-like texture. In several localities, the contorted bedding planes are readily recognized. Mn-calcite and quartz also crosscut rhodonite. Rhodonite deposits hosted by high grade metamorphic rocks may contain pyroxmangite. Rhodonite is an important gemstone and ornamental stone in B.C., second only to nephrite in dollar value. B.C. nephrite and rhodonite have been used for the past 100 years in local jewelry and ornamental applications. More recently they have been used in table tops, and they have potential as upscale materials in tile-making. There may be a market for tiles made from lower grade materials that were previously extracted and stockpiled. The prices of nephrite, jadeitite, and rhodonite vary widely with quality, but gem and ornamental grade stones are relatively highly priced materials and they trade world-wide.

Jan 1, 2001

By Yucheng Li, De Huang, Yonghong Liu

Mine frictional resistance is one of the essential parameters of mine ventilation systems, and it is of considerable significance for the prevention and control of mine risks and accident hazards. Frictional resistance requires a lot of resources and time and has errors. To reduce the errors of frictional resistance, a regression model of frictional resistance is proposed based on the correlation analysis of the affecting factors. Through the comparative test analysis of seven regression methods, it is found that the classification and regression tree method for solving the proposed regression model has better performance than other methods. The least square error criterion is used to calculate and rank the importance of the factors affecting frictional resistance. The results show that the cross-sectional area of the tunnel, the support method, and the presence or absence of devices or pedestrian ladders have the most considerable influence on the prediction accuracy of frictional resistance. The support methods and cross-sectional areas are essential input variables. Through the combination test analysis of the influencing factors, the results show that the regression model does not have predictive ability when the number of input variables is less than 3 and the best predictive performance cannot be obtained using all the influencing factors. The best prediction model of resistance is to combine the shape of the tunnel, the support method, the presence or absence of devices or pedestrian ladders, and the cross-sectional area. The method proposed in this paper does not require a lot of resources and time investment, and the frictional resistance error is small. At the same time, it solves the problem of resistance prediction with incomplete data of influencing factors and provides a compelling new method for obtaining frictional resistance parameters.

Jan 28, 2022

By Dan Urich

This paper covers the construction and operation of the Grate-Kiln system at the Humboldt Mine. The mine concentrator and pellet plant are located approximately 14 miles West of Ishpeming, Michigan, on the Marquette iron Range. Production of pellets began in mid-July, 1960.

Jan 1, 1962

By Scott G. Britton

This chapter is concerned with the construction of the dynamic component of belt haulage systems. The dynamic system includes the belt line and tailpiece extension and retraction movements in a production system where mine management is continually placing the belt in the most effective operating position. Correct installation of the belt and tailpiece during an extension is very important for many performance reasons. Two of the most important reasons are to eliminate spillage and safely operate the belt line. This chapter is divided into three major discussions. The first discussion looks at analyzing the parameters of effective belt line construction. This includes a review of the parameters and management tools needed for proper scheduling of a move-up. The second major discussion topic centers on efficient procedures for a belt line extension. Topics such as site preparation, tailpiece breakdown and setup, stringing the belt line and structure, plus operating and maintenance tasks needed after the belt line is installed and running, are covered. The third discussion presents a list of conveyor and conveyor component manufacturers who provide services and products to the coal mining industry. Again, any discussion on underground haulage systems must generalize much of the site specific design approaches to be practical. This text will mention, where applicable, some of the alternatives available to construction engineers in designing belt line systems.

Jan 1, 1983

There are presently in use many grinding mill control schemes and concepts. This paper presents one operating method of controlling the particle size of the cyclone overflows for proper metallurgical results and controlling the level of the cyclone feed sump and new feed rate to obtain lowest unit cost of finished (ground) material which is usually at the maximum grinding mill throughput. This system stresses simplicity of field instrumentation and control strategy. Both of these factors lead to better operator understanding and acceptance. The low capital investment of this system also makes it more attractive at the Buick Concentrator when compared to other more complicated systems utilizing mass flow measurement and a computer to calculate circulating load and infer particle size. Furthermore, it has the advantage of utilizing an actual measurement for control, rather than a difficult-to-maintain inferred value. There are several reasons for maximizing mill throughput at Buick. The milling rate before automatic control was too low when compared to mill throughput increases planned for the future. Through this new operating system, it appears Buick will not have to make major changes of mill motors and speeds to meet the increased? production rate. Also, since power costs continue to escalate, it is desirable to maximize the throughput to the grinding circuit and reduce overgrinding to achieve a reduction in power cost per ton of ore milled. Presently, 45% of the concentrators' total power is consumed in this grinding circuit.

Jan 1, 1977

By S. K. Mukherjee, A. W. Laurito, M. M. Singh, N. I. Jayaraman

This paper describes the application of foam to control respirable dust in a double-drum longwall mining section. The feasibility of injecting an adequate quantity of foam through the shearer drum was initially established in the laboratory. Thereafter, underground testing of the foam system to determine its effectiveness on an active operating longwall was conducted in a mine in West Virginia. The foam system proved superior to the water spray system. The details of the laboratory and field investigations, the results obtained, and the degree of acceptance of this system by the mining company are discussed in this paper.

Jan 1, 1987

By M. L. W. Tuttle, B. R. Berger

Our study focuses on the geology, hydrology, and geochemistry of a variety of molybdenum (Mo) porphyry systems. The systems are either high fluorine, granite, Climax-type, systems (e.g. Mount Emmons/Redwell Mo deposit, Colorado and Questa Mo deposit, New Mexico) or low fluorine granodiorite systems (e.g. Buckingham Stockwork Mo deposit, Battle Mountain, Nevada and Cannivan Gulch Mo deposit, Montana). The water quality of streams, natural springs, mine discharge, and ground water from drill holes were assessed in the region of these deposits. The ultimate goal of our study is to understand the environ-mental behavior of these Mo porphyry systems in the context of geologic setting, hydrologic regime, and climate.

Jan 1, 2004

By Raimo Matikainen, Pekka Särkkä

HISTORY The history of mining in the Outokumpu Co. shows continuous development of small and medium-sized mines, coupled with a permanent improvement in min¬ing methods and mechanization. Tables 1 and 2 provide a brief outline of the major events over the years of operation. Some of the mines have had relatively short lives as in the case of Nivala, Korsnas, Kylmäkoski, the surface pits of the Kotalahti, Vuonos, and Hammaslahti mines, and some very small pits. The sequence in which the mines started opera¬tions is shown in Table 1 and production increases in Table 2. GEOLOGICAL FRAMEWORK Most of the ore deposits in Finland (see Fig. 1) are situated in middle Precambrian (1500 to 2300 m.y.) formations corresponding to the Baltic shield. The ores and country rocks are generally firm, with a minimum compressive strength of 60 MPa (8700 psi). The sulfide ores, of importance to the national econ¬omy, can be divided into copper-nickel deposits, asso¬ciated with basic and ultrabasic rocks (1900 m.y.), and the sulfide ores found in well-preserved Svecokarelidic crystalline schists (1800 to 2300 m.y.) which contain varying amounts of copper, zinc, cobalt, nickel, and lead. Over 90% of the sulfide ore mined to date in Fin¬land and existing in the known ore reserves belongs to deposits situated in the main sulfide ore belt. This belt extends diagonally across the country over a breadth of Table 1. Sequence in Which Mines Began Operations 1913 Mining started at the Outokumpu mine (now called Keretti) 1928 Large scale systematic exploitation started in the Outokumpu mine Opening of mines: 1942 Nivala mine (1942-54) 1943 Yiojärvi mine (1943-66) 1947 Orijärvi mine (1947-54) (Mining started in 1757) 1948 Aijala mine (1949-58) 1952 Metsämonttu mine (1952-58 and 1964-74) 1954 Keretti's new mine plant 1954 Vihanti mine 1959 Kotalahti mine 1961 Korsnäs mine (1961-1972) 1962 Pyhäsalmi mine 1966 Virtasalmi mine 1967 Kemi mine 1970 Hitura mine 1971 Kylmäkoski mine (1971-74) 1972 Vuonos mine 1973 Hammaslahti mine 1978 Vammala mine Table 2. Ore Production of the Outokumpu Oy Mines Year 1000 t of Ore 1913-1928 252 1929-1954 13 075 1955 1 105 1960 1 784 1965 2 627 1970 3 269 1975 5 825 1976 5445 1977 4 939 1978 5 766 1979 5905 40 to 150 km, from Lake Ladoga to the coast of the Gulf of Bothnia. The main sulfide ore belt includes the Outokumpu copper-zinc, the Kotalahti nickel-copper, the Pyhäsalmi copper-zinc, and the Vihanti zinc ore zones. The Outokumpu ore district occurs in a mica schist area about 60 x 100 km, in association with belts of metamorphic Svecokarelidic quartzites, black schists, dolomites, skarn rocks, and serpentinites. The main ore minerals are chalcopyrite, pyrrhotite, pyrite, and sphalerite. In addition there are nickel and cobalt minerals such as cubanite and cobalt-pentlandite, which have been of economic importance. In this area, Outokumpu Oy exploits the deposits at Keretti and Vuonos. The latter was discovered as an extension of the Keretti ore field about 6 km to the northeast. The Kotalahti geological formation extends across nearly 400 km. The host rock of these mostly pipelike deposits is generally serpentinite, pyroxenite, or norite. The main ore minerals are pyrrhotite, pentlandite, and chalcopyrite. In this zone, the deposits of Kotalahti, Hitura, and Virtasalmi are at present under exploitation by Outokumpu Oy. The Vihanti geological formation is located in west¬ern Finland and is about 40 km wide and some 200 km long. The rock associations are crystalline schists including dolomites, mica schists, mica gneisses, gray¬wacke, and acidic or basic volcanic rocks, which change generally, in connection with the mineralization, into skarn and cordierite-anthophyllite rocks. The host rocks are dolomite, skarn, graywacke, and quartzitic rock and the principal minerals are sphalerite, chalcopyrite, galena, pyrite, and pyrrhotite. The accessory minerals are mainly cubanite, arsenopyrite, molybdenite, and native gold and silver. The two largest ore bodies being exploited at pres¬ent by Outokumpu Oy are the Vihanti mine, which pro¬duces zinc, lead, and copper, and Pyhäsalmi, which con¬tains copper and zinc. Deviating from the sulfide ore types described earlier is the Hammaslahti copper ore located in the southeast-

Jan 1, 1982

By Robert M. Mann

The Ag/S specific ion electrode has been evaluated for analysis of both free and total cyanide. Metal cyanide solutions were prepared from reagent grade compounds and by stoichiometric fixture of the metal with a potassium cyanide solution. Solutions containing Cu+1, Ni+2, Fe+2, Fe+3 and Zn+2 complexes were analyzed prior to and following EDTA pre treatment. This effort provides an understanding of the effect of each metal cyanide complex on the SIE analysis of free and "total" cyanide.

Jan 1, 1981

By Richard S. Kunter

The Bulldog CIP plant treats the slime portion of current tailings and reclaimed flotation tailings from the adjoining 350 tpd (3.67 kg/s) silver-lead flotation mill. Changes to the dredge reclaimer, pulp storage tank and trash removal system have allowed an increase in tonnage treated to a sustained 460tpd (4.83kg/s). CIP feed is 3-4 oz/T Ag (102.9-137.1 ppm). Following conventional cyanidation, carbon is added to the slurry. Silver loaded carbon is stripped in atmospheric-pressure vessels using hot caustic cyanide. Silver recovery from this solution is by Zadra- type cells. Some of the modifications to the plant and operating techniques are discussed.

Jan 1, 1981

By P. F. R. Altounyan, I. W. Farmer

Groundwater freezing was used to stabilise 8m thick beds of saturated and weakly cemented sands at a depth of 170m, during driving of twin 1 in 4,5.2m o.d. circular drifts from the surface to the Coal Measures through 600m of Permo-Triassic strata. Instrumentation was installed during erection of the lining in frozen and unfrozen ground to measure ground and groundwater pressures on the lining and ground temperatures up to lm into the frozen ground. Observations showed that following thawing, effective lining stresses in the frozen zone were low, indicating minimum strata disturbance during freezing and subsequent machine excavation. Groundwater pressures were lower than expected.

Jan 1, 1981

By Nick A. Hasenack

A full survey of the laboratory and blast-furnace tests on 2 types of acid pellets is given. From the laboratory tests, carried out in an atmosphere containing hydrogen, it appears that type B, produced out of 100% magnetitic ores, has a far better low temperature disintegration index and a lower reducibility index than type A, produced from a hematite/magnetite mixture. The swelling index, chemical composition and mechanical properties of both types of pellets do not differ significantly. From the blast-furnace test, carried out with a burden consisting of 45% of pellets and 45% of sinter with basicsty ratio about 2.2, and at constant driving rate, it follows that there is no significant relationship between the disintegration value of the pellets and the blast-furnace permeability. If also is concluded that the lower reducibility of the type B pellets leads to a significantly higher coke consumption.

Jan 1, 1975

By Donald C. Moore

Asamera Minerals Cannan Mine has been producing a 170 g gold/tonne (5 oz gold/ton) siliciaus flotation concentrate since July 1985. Flotation concentrate is shipped to a smelter for gold recovery. Numerous processes have been investigated to economically produce bullion on site. This paper describes the laboratory and pilot plant test results of a bacterial assisted oxidation of the refractory minerals. Economic comparisons with autoclaving and roasting processes are included.

Jan 1, 1989

By A. Anttila

The grinding mill is probably the most common unit operation used in mineral processing. There is, however, much which can still be done in the way of optimization. This paper discusses the results of a well controlled pilot scale test in which the performance of a tumbling mill with a conventional rubber lining equipped with lifter bars is compared to that with a smooth rubber lining of the magnetic type. The results indicate that the smooth lining is about 14 percent more effective with respect to energy consumption. By optimizing the size of the grinding media, the mill capacity can be increased in many grinding operations. In this specific case the -20 mm ball charge required 26 percent less grinding energy than one with a -30 mm ball charge. The energy savings can. in most cases, be converted to increased capacity. The wear of the grinding media is difficult to assess over a short period test but the results suggest it is somewhat less when a smooth lining is used. The wear of the linings has not been included in this study but it is generally accepted that the use of the magnetic lining reduces the lining costs dramatically. Computer simulation using the Millsoft code, developed by Mishra e.a. confirms and explains the increased effectiveness of comminution when smooth lining and smaller grinding balls are used.

Jan 1, 1998