Search Documents

By Leslie S. Halasz

This paper describes the techniques implemented at Randfontein Estates to develop twin-haulages at 'high speed'. An operation which culminated in the world record advance for twin-end multiblast cyclic development in hard abrasive quartzites. A major expansion project was planned for the mine, with the sinking of a third twin-shaft system (to be known as Cooke No. 3), to raise the level of ore production from 3 500 000 to 5 000 000 tonnes per alumm. Subsequent redesign of the proposed shaft system as a single 9 m brattice wall shaft took place, reducing the planned shaft sinking period by 12 months and saving an estimated R 250 000 (U.S. $ 330 000) in sinking costs. The advancement of the Cooke No. 3 Shaft sinking and development programme necessitated a rapid excavation schedule for two interconnecting twin-haulages from the existing Cooke No. 2 twin shaft complex to provide a second means of egress. An early holing between the two shafts would provide significant financial and technical benefits. Pre-development and equipping of shaft pillar excavations would enable a rapid shaft production build up and blocking out of at least one year's ore-reserves.

Jan 1, 1983

By B. P. Atkin, D. W. Brown

The handleability monitor has been specifically designed to provide a simple, rapid and on-site assessment of the whole or part consignment of a coal blend in its ‘as-received’ condition. Evaluation has been carried out at a number of coal-handling plants, on both metallurgical and power station coals from a variety of sources world-wide. The results which are used to predict which coals could routinely pass through a handling plant at line capacity, without causing blockage or delay, have also been correlated with moisture, ash and size analyses of the coal to develop a predictive model of handleability.

Jan 1, 2000

By Rolf Lange

Introduction The Harzwasserwerke, a public body of the Federal State of Lower Saxony, supplies drinking water to an area bordered by Braunschweig, Bremen, the Northern and the Western edges of the Harz-Mountains. From the very beginning in 1928, the Harzwasserwerke have been systematically constructing reservoirs in the western Harz which have the function of collecting and storing the frequently occuring flood waters as well as providing drinking water. The Grane-Reservoir with a capacity of 45 Million cu.m., the last of the big reservoirs, was built in 1968-1970. A system of connecting tunnels effectively enlarges the natural catchment area of this reservoir and the surplus waters of the Oker and Radau valleys - where floods occur particularly during the spring - are being conducted to the reservoir. By building the 4.800 m long "Radau-Tunnel", the waters of the Radau valley will now also be used more efficiently and its surplus waters will pass to the Grane Reservoir via this new tunnel and the Oker-Grane-Tunnel which was finished in 1970. The Project The Radaustollen has been planned and put out to tender by the Harzwasserwerke as a conventional "Freispiegelstollen". The horseshoe profile has a cross-section of 8 m2. Lining was required only in disturbed rock areas; lining of the whole tunnel was not necessary. The gradient of the tunnel is 4 % 0 rising = 25 m over the total length of 4.800 m.

Jan 1, 1979

By John L. Halls

INTRODUCTION In this section, it is assumed that the reader is an engineer with sufficient training in underground mining work, preferably with budgetary control, to understand the mining methods outlined in other sections of this handbook. The mining-method descriptions are not repeated herein; only sufficient information is provided to enable the reader to comprehend the development of the costs presented. All costs are in 1977 US dollars, except where explicitly stated otherwise. CAPITAL INVESTMENT The capital investment in the underground mining portion of any mining property includes the following: 1) The development of original access involving adits, shafts, declines, etc. It includes the necessary equipment for transporting men, materials, and rock. 2) The purchase of mine equipment including loaders, underground haulage equipment, fans, pumps, electrical distribution, surface facilities associated with the underground mine, etc. 3) Sufficient preproduction mine development to assure steadily increasing production after startup. De- pending upon the mining method used, the preproduction development should provide a supply of three months to one year of ore that is developed and is ready to be stoped. Underground development also includes excavations other than shaft stations, loading pockets, sumps, etc., which usually are associated with the means of access and are excavated by the contractor. These excavations could include a crusher cavern, an ore- storage pocket, and underground workshops that may or may not be included by the shaft-sinking contractor. Portions of these could be delayed until after production begins, but it is preferable to complete them during the development phase, so there is no interference with the production buildup. 4) The staff and labor costs for all phases from inception through final production. 5) The provision of mine-surface equipment and facilities strictly applicable to the underground portion of the operation. The required facilities include a changehouse with a lamp room, a first-aid station, compressors, an electrical substation, workshops, a ware- house, water pipelines to the concentrator, water storage tanks, explosive storage, etc. A concrete-batch plant, a sand-fill plant, and boilers for heating may be required. 6) Other direct and indirect costs. 7) Engineering, design, and procurement costs. 8) Contingency allocations. 9) Contractor's fees, startup costs, and owner's costs. Original Access As part of a study for the US Bureau of Mines, Dravo Corp. conducted an extensive literature research survey covering underground operations in the United States between 1963 and 1973. Table 1 is compiled from the section of that study pertaining to the types of access to underground mines. Table 1 does not include distances attributable to the deepening of existing shafts, nor does it include shafts bored by raise drills or downhole machines that need existing underground workings for the disposal of the cuttings. During the period under review in the report ( 1963 through 1973). concrete-lined circular vertical shafts were the predominant means of providing the first access to a new underground mine; these shafts accounted for 80% of the original access in terms of the number of accesses completed, and 75% in terms of the total verti- cal linear distances. The inside diameters of the conventional circular shafts ranged from 3.7 to 7.0 m (12 to 23 ft). Most (72% ) of these conventional shafts were for production,

Jan 1, 1982

The response of 174 domestic water supplies to longwall mining of the Pittsburgh coal seam was compared to various physical parameters. Sixty-four percent of domestic water supplies returned to service without the need for intervention, while thirty six percent required intervention to reestablish a suitable water supply. Domestic well response is strongly correlated with the topographic setting. Valley wells showed the least effect while hilltop wells showed the greatest effect. Well response was also found to be correlated to the location of the well above the mining with greater effects observed in zones of surface tension and compression, and fewer effects in zones which are stress neutral. Ground water supplies remained unaffected or were re¬established at 149 of 150 sites, indicating that ground water resources remain available to domestic wells after mining. Results of this study support the stress-relief model of ground water flow in the Northern Appalachian Basin. Longwall mining's effect on this system is to locally increase fracture connectivity in the near surface zone. This may shift the zones of saturated fractures to greater depths beneath hilltops and hillsides, and increase recharge and storage in valleys. General trends in well response are predict¬able utilizing the stress relief conceptual model, the topographic setting of the water sources, and their location over the mine.

Jan 1, 1986

By Paul M. Godlewski, Roberto J. Guardia

Hundreds of highway and rail transportation tunnels in North America have been rehabilitated in the last two decades. Tunnel rehabilitation is usually dictated by an owner’s need to extend the working life of the structure, but typically has the added benefit of increasing capacity (greater speed or increased clearance) and enhancing safety. Not only has rehabilitation proven to be an economical alternative to new tunneling, but it can be safely accomplished by working during short work “windows” without taking the tunnel out of service. This paper presents methodology for planning and designing of tunnel rehabilitation projects, and case histories illustrate successful excavation and support technologies.

Jan 1, 2003

By R. J. Matetic

The Bureau of Mines, as part of a program to improve mine planning and development, is currently investigating the effects of pillar load transfer, which can impact mining operations within a multiple-seam configuration. A comparative study was performed at two separate mine sites to determine the effects of this load transfer mechanism. The Bureau installed and monitored instrumentation at both sites to gather pertinent data on rock mechanics. At mine site A overburden depth varied dramatically in the vicinity of the study area and reached a topographic high at the study site: inner burden thickness was less than a pillar width (40 to 45 ft) (12 to 14 m): floor heaving was experienced in both coalbeds where sandstone and/or shale floor units were observed: overlays of the mine layouts show pillars were not totally super-positioned: a maximum of 5 in (13 cm) of roof to floor convergence was measured and pressure readings indicated pillar core loading only and increased to a maximum of 7,000 psig (48,300 kPa) over instrument setting pressure.

Jan 1, 1989

By A. Iordanidis

Mining activities have recently been taken place in Vourinos mountain, northern Greece, exploiting the so-called ?olivinite?. A representative sample was collected from this mining area. Mineralogical analysis was conducted using X-Ray powder Diffraction (XRD). A thin section was prepared and analyzed under optical microscope. X-Ray Fluorescence (XRF) was employed for the chemical analyses of major, mi-nor and trace elements. Environmental Scanning Electron Microscopy coupled with energy dispersive x-ray analysis system (ESEM-EDX) was also applied for the characterization of the sample. Forsterite (Mg-rich olivine) and enstatite (Mg-rich orthopyroxene) were the main mineral phases determined by XRD, with a 56% and 44% content respectively. Trace amounts of chromite spinels were also determined. Based on this characterization, the industrial rock proved to be a hartzburgite (a type of peridotite in petrological terms). Optical microscopy and ESEM-EDX provided similar observations and confirmed the above-mentioned results. XRF revealed a composition of 43.31 MgO, 44.25 SiO2, 9.98 Fe2O3, 1.40 CaO, 0.67 Al2O3, 0.22 MnO, 0.01 TiO2 and negligible amount of LOI (<0.1%). Trace elements with high concentrations were Cr (2678 ppm) and Ni (2044 ppm). The comprehensive characterization of this mining product suggested the suitability for various uses, such as refractories, foundry and slag conditioner. Additional experiments are being carried out for environmental applications, e.g. wastewater treatment.

Jan 1, 2006

By Deborah A. Peacock

"Outer space technology and exploration have reached a tipping point, so that mining and mineral processing in outer space is now a certainty and not a dream. Several competing companies worldwide are on the way to building spaceships to land on the Moon and eventually mine the Moon and asteroids for volatiles, rare earth metals and Helium-3.The Google Lunar XPrize offers a $30 million prize1. China has recently landed a spacecraft on the Moon. The European Space Agency, with cooperation from the United States, has landed a spacecraft, Philae, on a comet. And, Mars One is planning a one-way trip to establish a settlement of humans on Mars.How and why are the Moon and asteroids and their resources of interest to private space industry companies? Why are the Moon and asteroids viewed as a potential business venue?Geology of the Moon and asteroids — Why do we want to mine there?Space enterprises are actively working toward establishing and operating lunar and asteroid mining locations for resource extraction, resource processing, conversion to salable products and distribution of the products and services in space and to Earth and beyond2.Forty-five years ago, the Apollo manned missions to the Moon returned rocks and regolith to Earth, which were studied and analyzed. What they found was that the Moon contains valuable minerals and resources. These minerals are largely due to meteor and asteroid impacts, which have, over eons, created this mineral-rich regolith. These impacts have occurred on Earth as well, for billions of years, particularly early on in the history of the solar system. However, on Earth, wind, water and vegetation have erased most of these impacts. On the Moon, in contrast, the only weathering is caused by subsequent impacts and the solar wind."

Jan 1, 2017

By Ignacio González, Marcos Monroy, Valerie Bertrand, Roel Cruz

Results of an electrochemical study using carbon paste electrodes of pyrite and pyrrhotite samples suggest that the mineralogical impurities associated with these minerals are the determinant factor on their reactivity under alteration systems. These results were supported by mineralogical and leachate chemistry data from leach cell tests run on these samples. Pyrite reactivity decreases in the presence of associated impurities due to a galvanic effect whereas pyrrhotite reactivity appears to be controlled by the formation of a passivating layer, which overcome impurities effect. Electrochemical responses of sulfide-bearing samples provided valuable information on the prediction of ARD generation.

Jan 1, 2000

By R. A. Matuszak

Historically most mine management teams have been forced to operate in a more or less subjective manner. The objectives of mine management are simple and clear. Like other operational managements, mine management teams have the traditional well defined goals of improving efficiency and production while decreasing costs. Unlike other operational managements however, mining teams deal regularly with a vast assortment of uncertainties caused by: - Key production tools being mobile and widely dispersed, and - Non-uniform mining conditions At best in most operations these conditions cause obstacles to productivity and at the same time cause long delay in managment awareness of the obstacles. Planning with delayed feedback of information about necessary deviations is incomplete planning. For these reasons increased operational efficiency remains a constant though somewhat elusive goal.

Jan 1, 1985

By Stanley C. Suboleski, C. B. Manula

INTRODUCTION In any mining operation all possible steps should be taken to increase efficiency. One area for improvement is mine planning and design, particularly in the area of equipment selection for room-and-pillar systems. Be- cause of the availability of a wide variety of face machines, a fair degree of selectivity can be exercised in the choice of equipment for a particular job. However, this choice must be made on the basis of quantitative facts and forecasts related to the mining application. The purpose of this section is to develop and analyze the details of the mining process. Some specific areas studied include the relationship of system design to productivity, suboptimization as a result of equipment changes, and measurement of system performance. The plan of work leading to a quantitative description of these study areas is based on the growing interest in total system design using simulation as an analytical method (Manula, 1963). CHARACTERISTICS OF PRODUCTION OPERATIONS FROM ROOM-AND-PILLAR SECTIONS For a given mining method, raw production in a given section of a mine is primarily dependent upon the coal seam thickness, roof and floor conditions, methane emission, the mining methods, and the man-machine element. Average section production varies from 300 to 800 st per shift for conventional and continuous mining in high seams and from less than 100 to 300 st per shift in low seams. Since the reject varies from 0 to 40%, these figures must be decreased by the appropriate percentage to reflect the amount of clean coal mined. Personnel requirements per production section per shift for the various methods are listed in Table 1. Table 1. Production Personnel Method No. Method No. Conventional 12-1 5 Longwall 9-14 Continuous 9-1 2 Shortwall 9-12 MINING VARIABLES To evaluate the constraints and interrelationships for various mining methods, it is necessary to categorize the variables which underlie system production potential. Seven critical independent variables which determine production can be identified and categorized (Suboleski, 1978) : Seam Height The five categories are as follows: less than 36 in.;. 36 to 55 in.; 55 to 100 in.; 100 to 180 in.; and greater than 180 in. Floor Quality Floor quality ranges from : Excellent: Smooth, hard, grades less than 1 to 1 % % , and dry. Good: Smooth, soft but dry, with grades less than 3 % . The floor will deteriorate, but cautious operation can prevent it. There may possibly be heaving at some later time. Fair. Soft and damp. There is occasional interference with equipment operation; requires the use of four-wheel drive shuttle cars; ruts with regular use, and may have adverse grades of 5 to 7%. This may be coupled with slippery bottom and/or occasional steep rolls. Poor: Soft and wet. Requires blocking of the bottom to support equipment. There are frequent steep rolls and grades in excess of 7%. Roof Quality Roof quality ranges from : Excellent: Men are able to work under the unsupported top during the initial production cycle if legally permitted. Good: The roof is bolted on a 4 x 4 or 5 x 5 pattern with short bolts (442 in.) or <seam height if the seam >42 in., or requires posting with no bolts on a 4 x 4 or 5 x 5 pattern. There are no falls. Average: The roof is normally bolted on a 4 x 4 or 5 x 5 pattern, but with long bolts (>seam height or >6 ft.). There are infrequent minor falls or there may be an excellent roof which is difficult to drill. Fair: This type often requires spot bolting in addition to the regular pattern or bolting with planks. The roof conditions require shorter than planned cuts, or narrow cuts. Poor: This type requires bolts plus crossbars and posts, or installation of yielding supports or truss-type support. It is almost certain to fall if this is not done. Methane Liberation This ranges from none detected to low (no buildup at the face, even with minimum ventilation requirements) to moderate (the curtains must be extremely tight and tubing close to the face or methane will build up to 1 % during the loading of the car) to high (methane will build up to 170 if the miner is operated at the normal rate, even with proper ventilation). Hardness of Coal Coal hardness falls into the following categories: Soft: Soft coal is easily cut by a continuous miner. A plow could be used by longwall. Average: Coal of average hardness could be easily cut by a miner, and a shearer would be used in the longwall. Moderate: Moderately hard coal causes difficult cut-

Jan 1, 1982

By Ross W. Smith

Many studies have been made of the microflotation of quartz (1,2,3,4,5,6) and alumina (3,5,6, 7,8) using various anionic and cationic hetero- polar hydrocarbon surfactants as collectors. A few studies have been made on these minerals using amphoteric hydrocarbon collectors ( 9,10, 11,12) and only a few studies have been made on the use of fluorocarbon surfactants as flotation collectors (13,14). The present investigation compares microflotation response of the two minerals in hydocarbon and fluorocarbon collector systems of the anionic, cationic and amphoteric types. An attempt is made to relate flotation response of the minerals to their electrokinetic behavior and the pKa values of the collectors.

Jan 1, 1979

By Ronald B. Gabitzsch, Norbert P. Hanke

During 1982, record advances have been achieved in the excavation of vertical shafts with a V-Mole (a vertical shaft boring machine). The V-Mole, supplied by Wirth GmbH in Erkelenz, West Germany, has been used in West German coal mines since the early seventies, mainly for the construction of internal shafts. In 1981, it was brought into the United States for the construction of a series of ventilation shafts with depths varying between 512 m (1680 ft.) and 622 m (2040 ft.) excavated to 7.0 m (23 ft.) diameter. These shafts were needed for the development of coal mines for Jim Walter Resources, Inc. in Brookwood, Alabama. After a description of the mechanized shaft excavation system with the V-Mole, the conditions and parameters, such as ground, shaft dimensions, and linings are discussed. These factors are important considerations for a technically and economically feasible utilization of the V-Mole. In addition, the advantages and disadvantages of using the V-Mole technology in comparison to other shaft construction methods are evaluated.

Jan 1, 1983

By Fred N. Kissell, George H. Jr. Schnakenberg

INTRODUCTION A variety of instruments are available for measuring or monitoring the performance of underground mine-ventilation systems. In general terms, the instruments may be classified as those that measure air velocity and those that measure gaseous concentrations. All costs herein are in terms of 1978 US dollars. The mention of a specific manufacturer or device is not intended to be an endorsement by the US Bureau of Mines. AIR-VELOCITY INSTRUMENTS The basic instruments used for measuring the air velocity in mines are the vane anemometer and the smoke tube. Vane Anemometer Of the air-velocity instruments, the 102-mm (4.0¬in.) vane anemometer is the most common and is available as either a low- or high-speed type. The low-speed anemometer generally is the most suitable for measuring the velocities in ordinary airways. For a rough check of the velocity in an airway, it usually is satisfactory to hold the anemometer by hand, positioning it in the center of the airway for 30 sec. However, the resultant error may be as high as 25% , and such a hand-held approach is unsuitable when accurate or reliable measurements are required. To obtain more accurate measurements, the proper procedure is as follows: 1) Since holding the anemometer by hand generally causes the instrument to read about 15% high, it is mounted on a 0.6-m (2-ft) extension rod. 2) The airway is divided into equal right and left halves. A 1-min traverse is used in each half, moving the anemometer smoothly up and down in a zigzag pattern so that the entire half is covered within the allotted minute. 3) The manufacturer&apos;s correction table is applied to the readings to adjust the velocity calculation as necessary. Whenever possible, anemometer readings should be obtained in a long straight section of airway that has a constant cross-sectional area. Bends and obstructions should be avoided, since they cause turbulence and other discontinuities in the airflow and can degrade the accuracy of the velocity measurements. Although a series of velocity measurements at one location usually corresponds to within a few percent, this is not an indication that the airflows calculated from those readings are completely accurate. One reason is that the correction table provided with the instrument generally is not for that specific instrument; instead, it represents the average correction for all such instru¬ments made by the particular manufacturer. Most cor¬rection tables specify a correction factor of from 0 to 15%, depending upon the velocity. However, even after correction, the instrument error still may range from 3 to 5%. At low velocities such as those below 0.76 m/s (150 fpm), the instrument error can be two or three times greater than this, ranging from 6 to 15%. The new ball-bearing anemometers generally perform somewhat better at low velocities than did the older conventional anemometers. Another source of error is introduced when measur¬ing the cross-sectional area of the airway or entry. Under the best of circumstances, measurement errors, instrument errors, and a host of other minor errors all combine to cause a total error of at least 10% in the velocity calculation. The vane anemometer also can be used with reason¬able accuracy to measure airflows in mine-ventilation ducts. In this application, the anemometer is mounted on a rod and is held at the center of the duct end. For a duct that is discharging air, the average velocity in the duct is 85% of the centerline reading (Northover, 1957). For a duct that is taking in air, the average velocity is 70% of the centerline reading (Haney and Hlavsa, 1976). To measure the airflow discharged from a regulator or from a small hole in a stopping or bulk¬head, a correction factor for the area is necessary. A good approach in this situation is to traverse the area of the regulator or hole, holding the anemometer with an extension rod. This provides an average velocity that is multiplied by 85% of the measured area of the regulator or hole. In all cases, the manufacturer&apos;s instrument cor¬rection table must be used and applied properly. For accurate results, the anemometer should be returned to the manufacturer for periodic cleaning and checking. If it is in daily use, the anemometer should be returned about once per year, and proportionally less frequently if the usage is less frequent than on a daily basis. Smoke Tube The smoke tube may not appeal to individuals who believe that good measurement results can be obtained only with expensive, complicated, and fragile instru¬mentation. Nevertheless, smoke works about as well as anything for the routine measurement of low air velocities in mines. The following procedure yields reasonably good results: 1) Two marks are scratched 7.6 m (25 ft) apart on the floor of the airway. 2) The smoke tube is used to release a cloud of smoke in the center of the airway, about 0.9 m (3 ft) upstream of the first mark on the floor. 3) A timed interval begins when the leading edge of the smoke cloud passes over the first mark, and the interval stops when the leading edge of the cloud passes over the second mark. 4) A factor of 20% is subtracted from the cal¬culated velocity to determine the true average velocity, providing a correction for the centerline and for the spreading effect at the front of the cloud. Velocities calculated with the preceding method generally are accurate to within 10 to 15%. In some instances, the cloud from a conventional smoke tube

Jan 1, 1982

By Henry O. Ash

On June 16, 1982, Rio Blanco submitted a request to the US Minerals Management Service for a suspension of operations under its federal oil shale lease. The company also wanted a five-year delay in the requirement for further minimum royalty payments and a five-year extension of the primary lease terms of 20 years. The request was granted in late July in the midst of yet another slump in oil shale activity. Rio Blanco holds one of four Federal oil shale leases that were granted under the Interior Department&apos;s Prototype Oil Shale Leasing Program in 1974. That year the DOI offered for lease six federal oil shale tracts, two each in Colorado, Utah, and Wyoming. The leases in Colorado and Utah were granted for substantial bo¬nus bids as shown in Table 1, but the Wyoming tracts had no takers. In the eight years hence, no oil shale has been produced commercially. Indeed, the prospects for successful oil shale development have fluctuated widely, continuing a 60-year- old cyclical pattern in the fledgling industry. The prototype program was developed and initiated while this infant industry struggled to begin anew, without the benefit of any federal oil shale leasing regulations, or any history of federal oil shale leasing at all. Permanent regulations were not required because the effort was limited and designed to provide the foundation for any future leasing program. Section 21 of the Mineral Leasing Act of 1920, a Nov. 30,1973 Federal Register notice, and the leases themselves constitute the legal and regulatory framework for leasing and developing prototype oil shale tracts. The prototype leases contain some unusual provisions including installment payments of the bonus bids, credit of early development costs against payments due the government, adjustment of royalty rates according to regional crude oil price fluctuations, and unusually extensive and detailed environmental stipulations. Several of the provisions were intended to provide incentives for early development and financial penalties for failure to develop. The requirement for minimum royalty payments in lieu of actual production royalties beginning in the sixth year of the lease falls in the latter category. After the sixth year, the required minimum payment is increased east year through the 15th year by an increment equal to that due in the sixth year. The minimum royalty then remains the same through the final five years of the primary lease term. Minimum royalty is calculates on a different production level for each prototype lease, based on the quantity of 125 L/t (30 gal/st) shale estimated to be recoverable from. each tract by room-and-pillar mining. That mining system was selected for reference as the only proven extraction method for oil shale at that time (early 1970s) The minimum royalty (production) rate was calculated for each tract by direct comparison of its estimated recoverable 125-L (30-gal) resource to a hypothetical tract containing 1.9 Gt (2.1 billion st) of recoverable 125-L (30-gal) shale. For the hypothetical lease tract, the minimum production for the sixth year was calculated to be 3.2 kt/d (3,500 stpd), increasing by a like amount each lease year through the 15th to a daily production rate of 31.7 kt (35,000 st). Under this formula, the hypothetical lease tract would yield $16 million in minimum royalty payments over the 20-year primary lease term if there were no production, no development credits taken, and no adjustment of the royalty rate due to fluctuation of regional crude oil prices. The production rate of 31.7 kt/d (35,000 stpd) was a somewhat arbitrary figure that was considered, in the early 1970s, to represent a minimum size for a commercial oil shale operation. A production rate of 7.9 dam3/d (50,000 bbls/day) soon supplanted that smaller mine production figure as a rule of thumb for the minimum size for a commercial facility. The proportional relation-

Jan 11, 1982

By B. Anameric, S. K. Kawatra

Pig iron nuggets were produced in a laboratory scale furnace at Michigan Technological University. These nuggets are produced from pellets consisting of a mixture of iron oxide, coal, flux, and a binder, which are heated to 1450°C.These pellets then self-reduce to produce a solid, high-density, highly metallized (96.5% Fe) pig iron. During the nugget production process, a separate slag phase forms that cleanly separates from the metal. The physical and chemical properties of the pig iron nuggets are similar to pig iron produced by blast furnaces, which is distinct from Direct Reduced Iron (DRI).

Jan 1, 2004

By T. R. von Ow

The method of powering mills such as AG, SAG and Ball has a long and technically interesting history. It can be said that almost every decade in the last half century had its own trend. The trends were dominated by the market demand, the advanced process development and requirement of the mechanical and the electrical technology but mostly by the price of the applied technology. The increasing size of the ring geared mills in the last years requires more awareness on the drive train solution. Special attention must be paid to the mechanics and the requirements of the power grid. Operational challenges such as soft starting and controlled operation as well as the protection of the equipment have gained importance. Frequency converter drive solutions dedicated to single or dual pinion ring-geared mills offer significant advantages over conventional drives due to their application specific features and controls. Solutions with low speed motors as well as high speed motors cover all possible configurations available for ring geared mills.

Jan 1, 2010

By Menglong Bian, Xiaotong Dong

Thermal damage is an urgent problem faced by deep mining. High-temperature rock mass, hot water and electromechanical equipment are the sources of the thermal damage. The increase in air temperature in mine tunnel is the result of fluid–solid coupling heat transfer from various heat sources. This paper takes a roadway with hot water and a mine car as the research object. Based on the Fluent, Static Structural and Steady-State Thermal modules in ANSYS, the thermal-fluid–structure coupling analysis in the roadway is carried out. It is found that the hot water has a significant effect on the thermal environment of the mine. Under the experimental parameters, the maximum heat flux density and equivalent elastic strain at the interface between the hot water and the rock are 9789.3 W/m2 and 0.00054532 m/m, respectively. The heat flux distribution in the rock area near the mine car does not change much, and the equivalent elastic strain value in this area is high. After the air is heated in the hot water area, the temperature curve changes gradually and then rises steadily. By changing the inlet air temperature parameter, it is found that the lower the inlet air temperature, the better the cooling effect, and the change of the inlet air temperature can change the air temperature field in the roadway as a whole. By changing the parameter of inlet air speed, it is found that higher wind speed brings better cooling effect, but with the increase in wind speed, the cooling effect of roadway thermal environment is very limited. When the wind speed increases from 5 m/s to 10 m/s, the air temperature of most measuring points drops by more than 2℃; when the wind speed increases from 15 m/s to 20 m/s, the air temperature of most measuring points drops below 0.7℃. After the wind speed reaches a certain value, the cooling effect of ventilation is very limited.

May 5, 2022

By Jim Oehler

The US minerals industry, as well we know, has been hit hard by the recent recession and is faced with what is projected to be a slow recovery. Even so, there was an underlying feeling of optimism at American Mining Congress&apos; International Mining Show in Las Vegas, NV, Oct 11-14. More than 25,000 people attended during a particularly rough financial year, dispelling fears that attendance would dip sharply below 1978&apos;s 30,000 plus tally. The equipment expositionheld every four years-was the largest show of its kind this year in the Western Hemisphere in terms of exhibit space, providing an extensive view of mining-related equipment. In addition to the nearly 700 exhibits occupying more than 445 hm2 (11 acres), 20 technical sessions were held covering topics ranging from minerals availability and the state of the mining industries to communications, computers, and accounting. Government officials were well represented, with six US senators and five US representatives participating in various convention functions. Sen. Paul Laxalt (R-NV) was the keynote speaker at the welcoming luncheon. Other senators involved in the show included Howard W. Cannon (D-NV), Pete V. Domenici (R-NM), James A. McClure (R-ID), Frank H. Murkowski (R-AK), and Steven D. Symms (R-ID). Representatives on the program were Joseph M. Gaydos (D-PA), Guy Vander Jagt (R-MI), Don Young (R-AK), Jim Santini (D-NV), and Ceil Heftel (D-HI). There were also many international vistors at the show, including exhibitors from Australia, Austria, Canada, England, Finland, Sweden, South Africa, and West Germany. Equipment Highlights Equipment and services featured at the exposition ranged from aerial mapping to wire rope. Aisle space alone between exhibits exceeded 8 km (5 miles). And the companies represented ranged from small businesses to large corporations. Some of the company products described here are representative of the many exhibitors in attendance. Atlas Copco&apos;s extensive display of rock drilling and tunnel and shaft boring equipment featured its Boomer H-201, the newest addition to its line of underground drifting rigs; the ROC 306, a new track-mounted, high pressure down-the-hole drill rig; a new hydraulic surface crawler drill, the ROC 712H, designed for small and medium-size holes in quarries and small open-pit mines; a computerized analysis system, CARE (see page 1570), designed to project productivity and operating costs for various mining operations; several electro-hydraulic loaders, including the new rail bound LM E60 and LM E80, and two Hagg-loaders-the 7HR and 10HR-that use two digging arms to rake and guide muck; a mechanized blasthole charging system; rock bolting equipment and its new Swellex roof bolting method; Sandvik Coromant drill steel and bits; and its new Jarva R200 raise boring machine.

Jan 11, 1982