Search Documents

By L. Xiao

Using K-oleate as a collector and alizarin red S (ARS) as a modifying agent, selective depression of dolomite from francolite was achieved in alkaline medium (pH> 9.0). Interestingly. ARS was also found to depress igneous apatite in alkaline medium in oleate flotation of apatite and calcite. Adsorption of ARS alone on dolomite was found to be higher than that on francolite. Complimentary adsorption experiments of ARS and K-oleate showed that oleate adsorption was increased in the presence of ARS on francolite but not on dolomite. K-oleate adsorbs on both francolite and dolomite and causes precipitation of calcium and magnesium oleate. Such precipitates can be pre-vented when ARS is present. The results are explained in terms of competitive adsorption for the active sites on francolite and dolomite by oleate and ARS, and their interactions with dis-solved mineral species in solution.

Jan 1, 1988

By Noris Del Be1 Belluz

Drilling underground in the Grasberg dewatering drifts has routinely hit water aquifers with high flow rates and pressures. Two types of holes are used. Pilot holes probe ahead of the tunnel development to intersect aquifers ahead of the face. And dewatering holes dewater rock formations that will drain water from the Grasberg pit and allow tunnel development to proceed safely. Recently, static pressures of >8.3 MPa (> 1,200 psi) have been recorded with flows from a 100 mm (4 in.) HQ core hole measured at 5,700 L/min (1,500 gpm). The waterflows can be slightly acidic, necessitating the use of stainless-steel collar gear to resist corrosion. These rates were anticipated and contingencies were planned early on to deal with these conditions. PT Freeport Indonesia (PTFI) established procedures to maintain the safety of the drill crews, to enable coring of the rock, and to maintain the safety of the miners driving the drifts. The collar gear controls the waterflows because these drill holes are a vital source of water for the concentrator.

Jan 1, 1998

By F. A. Edwards

The Macassa Division of Lac Minerals Ltd. is a high grade gold mine that has been operating in Kirkland Lake, Ontario for the past 51 years. It produces approximately 120,000 tonnes of ore per year, averaging approximately 18.7 grams per tonne (0.45 ounces per ton) of gold. Over the years, the ore body has been developed to a point where mining takes place below the 1,220 m (4,000 feet) elevation and 1,830 m elevation (6,000 feet) west of the original shaft. The mine is currently serviced by two surface and two winze shafts. (Figure 1). The ore body extends below the 1,930 m (6,400 feet) Level which is the bottom of the existing mining operation. An ambitious underground exploration program has substantially increased these reserves. Concurrent with the discovery of greater reserves, has been rapidly escalating mining costs, particularly labour which constituted 66% of the total cost in 1981. These costs continued to escalate as the major proportion of mining was carried out to the west, far away from the existing hoisting systems. This required a three lift hoisting system for men, materials and ore. In addition to the increased travel time and ore handling expense, increased humidity, temperature, ventilation and compressed air losses have added to the inefficiency of the operation. As a result, studies were initiated in 1980 to assess the future of the Macassa operation. The results of the studies indicated that a new deep shaft with a potential to hoist from 2,135 m (7,000 feet) or below was the most attractive option. Detailed design of the shaft and associated surface plant commenced in January, 1982 and the following milestone dates were achieved: 1980 - initial study of hoisting and haulage facilities; January, 1981 - ore reserves in excess of 1 million tonnes of ore at 18.7 g/tonne (0.45 oz/ton) confirmed; March, 1982 - preliminary study of Macassa No. 3 Shaft completed; April, 1982 - permanent hoisting plant purchased; June, 1982 - site clearing commenced; September, 1982 - shaft collared; May 1, 1983 - shaft sinking commenced; February 11, 1985 - shaft reached 1,600 m (1mile); December 1, 1985 - shaft scheduled for completion.

Jan 1, 1985

By R. O. Ifill

Alternating current electrocoagulation (AC/EC) may be an alternative to chemical coagulation in the thickening of tailings in the mineral, coal and petroleum industries. In the current study, ground silica (d50 as received, 20 µm) served as the model tailings solid with characteristically poor settling behavior. Its natural initial settling rate was 1.6 x 10-3 cm/min. This paper discusses the indirect application of AC/EC via aluminum electrodes to the enhancement of the settling behavior of the silica. ?Indirect AC/EC? means that the silica was coagulated upon dispersion in water that had been treated by AC/EC. The effect of AC/EC retention time on settling behavior is examined and the water chemistry is analyzed. Test results show that the initial settling rate of silica was enhanced by a factor of 4,000 at its maximum of 6.4 cm/min, under the conditions employed. Settling enhancement was achieved upon contact between the AC/EC-treated water and the silica, and the enhanced initial settling rate was dictated by the floc size. The aluminum dosage increased with AC/EC retention time, reaching a maximum concentration that was equivalent to 13.1% of that predicted by Faraday?s law. Complex aluminum ions are considered to have adsorbed onto the silica surface and an adsorption mass ratio of 0.3 mg Al/g silica was the most effective in enhancing settling behavior. Owing to pH change or slow kinetics, aluminum hydroxide precipitation did not lower the ion product ([Al3+][OH-]3) below the KSP of 6.3 x 10-32.

Jan 1, 2011

By P. Riveros, A. Pratt, G. Deschênes

The effect of pyrite, pyrrhotite, chalcopyrite, realgar and arsenopyrite on gold dissolution in cyanide media was investigated. The cyanidation of synthetic gold ores in the presence of various concentrations of sulfides was studied under constant experimental conditions. A mineralogical analysis of the minerals was performed. The leaching kinetics were determined. The negative effect of sulfides on the gold dissolution rate varies with the sulfide mineral and decreases according to the following order: realgar > pyrrhotite > chalcopyrite > pyrite > arsenopyrite. The chemical characterization of gold and sulfide minerals surfaces using X-ray photoelectron spectroscopy (XPS) was undertaken to identify the mechanisms involved. XPS analysis showed that a passivation layer of sulfides, arsenic or iron compounds might form on the gold surface as a result of the dissolution of the sulfide minerals. Key words: Gold dissolution, Cyanidation, Effect of sulfides, Leaching kinetics

Jan 1, 2003

By Thomas F. Martin, Daniel J. Sieve

In April 1988, the joint venture of Morrison-Knudsen and Paschen Contractors (M-K/P) was the successful low bidder for the Metropolitan Water Reclamation District of Greater Chicago's (MWRD) Contract Number 73-164-2H. This project is yet another in the MWRD Tunnel and Reservoir Plan (TARP) devised to control and treat overflows from combined sanitary and stormwater flows. M-K/P's project, located along the Des Plaines River, consists of 21,569' of tunnel mined to a 35' diameter and two tunnels totaling 14,529' mined to a 12' diameter. All three tunnels will have 12" thick reinforced concrete lining. The path for combined sewer/storm waters to reach the tunnels begins at a connection structure, continues through an approach sewer, a sluice gate structure and down a vertical shaft which is topped by a backflow structure. The purpose of the backflow structure is to prevent water surging to the surface as the system fills rapidly. Backflow preventors represent a change in design after problems developed on earlier constructed portions of the T.A.R.P.. On this project, 14 drop shafts channel flows to the tunnel system. In addition to the drop shafts, contract specifications require an emergency or escape shaft be located not more than 4000 feet from the tunnel headings. Due to long reaches without drop shafts, four access shafts had to be constructed. Thus, the total shafts constructed under this contract will be eighteen plus one 30' finished diameter construction shaft located within Miller's Meadows. Figure 1 shows the overall Des Plaines River System and the M-K/P contract connection to previous and future MWRD projects.

Jan 1, 1991

By Zhan-fang Cao, Hong Zhong, Li-feng Li, Shuai Wang, Xiao-yu Cao, Guang-yi Liu, Ming-ming Wang

"In recent years, there has been an increasing focus on the hydrometallurgical processing of molybdenite, with the decline of high-grade and easily handled molybdenum minerals. In this work, a novel method of selective extraction of complex molybdenite concentrate, which is characteristic of high-grade copper ore, has been investigated. The results show that the leaching of chalcopyrite was impacted by the pH of the electrolyte when sodium carbonate and ammonium acid carbonate were added to the electrolyte. The leaching rate of molybdenum reached 99.39%, but chalcopyrite could not be leached at all in 240 min under experimental conditions of liquid-to-solid ratio 25:1, concentration of NaCl 4 mol/L, pH=9, room temperature and agitation speed 400 rpm. The grade of copper in the residue was 21.84%, with a recovery 99.93%. The technology of selective electro-oxidation leaching of molybdenum and recovery of copper from complex molybdenite concentrate is an effective separation method. The diffusion control model can be used to describe the process of leaching of molybdenum. The activation energy of the leaching reaction was found to be approximately 9.21 kJ/mol.IntroductionWorldwide, high-grade and easy-to-handle ore is decreasing, while the proportion of low-grade and complex ore is increasing. Porphyry copper ores with associated low-grade molybdenite are very abundant in China. Molybdenum is a valuable byproduct in the processing of porphyry copper deposits where the molybdenum is present in low quantities in the form of molybdenite (MoS2). In the conventional processing of copper sulfide ores by froth flotation, most of the molybdenite in the ore floats along with the copper sulfides. In this way, a bulk copper-molybdenum concentrate is produced. Afterward, the bulk coppermolybdenum concentrate is treated by differential flotation to obtain a rougher molybdenum concentrate, which requires several successive cleaning steps to produce a final molybdenum concentrate. However, it is widely recognized that flotation alone cannot economically produce a high-grade molybdenite concentrate, i.e., with less than 0.5% Cu. Therefore, in most cases, it is necessary to use a final step of chemical purification of the molybdenite concentrate to reduce the copper content to a level suitable for the market (Antonijevic and Pacovic,1992; Gerhardt et al., 2001; Fu and Zhong, 2003; Reza et al., 2006, Rafael et al., 2013)."

Jan 1, 2015

By Fred N. Kissell

Work done by Foster-Miller Associates under a Bureau of Mines research contract has developed methods to increase significantly the amount of fresh air that reaches the front of a continuous-mining machine. The emphasis was on removing methane build- ups that occur at the cutterhead. Using a full-scale plywood mockup of a coal mine working face area, the study showed that in many instances only about 20 pct of the fresh air heading towards an exhaust brattice or tubing actually gets to within 1 ft (0.3m) of the face. The key to providing more air at the face is to enhance and move forward the natural airflow pattern. This change in the natural airflow pattern can be accomplished by taking advantage of the air-moving abilities of the conventional water spray. It was discovered that if all the water sprays on the machine were realigned, then ventilation efficiencies of 70 pct or more were achieved regularly. This meant that if 9,000 cfm (4.2 m3/s) was entering the brattice, at least 6,300 cfm (3.0 m3/s) of this was reaching to within 1 ft (0.3m) of the face. This water spray realignment consists of placing a few nozzles on the side of the machine opposite the curtain and also tilting the front sprays slightly towards the curtain side. Recently, two underground tests and two additional independent laboratory tests of the water "Spray Fan" have been completed. In general, they have confirmed the performance of the Spray Fan system, but they also have provided useful information as to its difficulties and limitations.

Jan 1, 1980

By E. Ilgar

Biodegradation of spodumene by Asnergillus niger has been investigated. This organism oxidizes sucrose to citric and oxalic acids (in approximately 50-sot proportions) which degrade the spodumene mineral. The kinetic effects of leach variables on the dissolution of lithium were determined. The maximum theoretically attainable rate of lithium extraction was calculated for the effect of pulp density, to be V : 3.01 x 10 kg m sand the corresponding constant value, K = 12.47% pulp density. The apparent activation energy of lithium extraction vas found to be ^E = 20.3 kJ and frequency factor A = 5.66 x 10 s for S-spodumene leaching by synthetic -3 citric and oxalic acids (each in 0.05 kmol m-3 concentrations).

Jan 1, 1989

By G. W. Riley, D. E. Pickett

HINDERED SETTLING CONCENTRATION In the free settling of mineral particles in a liquid, the falling particles are at a distance from each other so that no particle is affected by its neighbor. In hindered settling, the concentration of particles is sufficiently high so that each particle is affected by its proximity to other particles in the suspension. Richards and Locke86 have described the hindered settling phenomenon as the condition “.. where particles of mixed sizes, shapes and densities in a crowded mass, yet free to move along themselves, are sorted in a rising current of water, the velocity of which is much less than the free-falling velocity of the particles but yet fast enough so the particles are in motion." This is the condition normally encountered in mineral con¬centration processes. The well known Newton equation for free settling of coarse (ap proximately +10-mesh, 1/16-in. or -- 2000-µm) spherical particles is:87 where v," is free settling velocity, cm/sec; p' is density of the fluid; p is density of the particle, g/cm3; d is particle diameter, cm; g is acceleration due to gravity, cm/sec2; and Q is coefficient of resistance, dimensionless, ~0.4. For the settling of fine spheres in water (approximately 150 mesh or 100 µm) the equation of Stokes pertains:87 where µ is viscosity of the fluid in poises and the other symbols have the same meaning as those in Eq. 1. For particles whose size lies between about 10 mesh (--2000 µm) and 150 mesh (100 µm), their settling velocity can be determined from experimental data. These data are available in convenient form in the text by Taggart88 based on the original work of Richards. Alternatively, a Reynolds number-coefficient of resistance plot may be used to determine the settling rate of such particles.87 The settling rate of spherical particles under hindered settling conditions can also be calculated from Eqs. I and 2 by replacing p', the density of the fluid, by p" the apparent density of the suspen¬sion. The concentration of particles in the fluid thus imparts an appar¬ent density to the composite fluid or suspension greater than that of the liquid alone, resulting in a buoyant effect on the larger particles. Particle shape affects the settling rate of both coarse and fine particles. The general effect is to reduce their settling velocities and the effect is greater for coarse particles and for those settling under hindered settling conditions than for fine particles or free settling ones. For two particles of differing densities but settling at the same velocity under Newtonian conditions, the ratio of their diameters from Eq. 1, called the free settling ratio is: where L signifies the lighter particle and H, the heavier particle. Under Stokesian conditions the exponent would be 0.5. For hindered settling conditions the fluid density p' is replaced by the apparent density of the suspension, p", to obtain a generalized equation for the hindered settling ratio: assuming both particles settle in approximately the same regime. The free settling ratio as given by Eq. 3 has been called by Taggart88 the "concentration criterion" and is used to predict the effectiveness of any gravity concentration process (see Introduction to this section). Based on Eqs. 3 and 4, if two particles of densities pH and p,, settle at the same velocity, the diameter of the lighter particle will be larger than that of the heavier particle. For example, in the case of galena (pH = 7.5) and quartz (pL = 2.65) settling in water (p =1.0) under free settling, Newtonian conditions 3.9. Thus, a quartz particle nearly four times as large as a galena particle will settle at the same velocity. Any quartz particle just slightly less than four times the diameter of the largest galena particle may be separated from it. Under hindered settling, Newtonian condi¬tions in a suspension where p" = 1.65, dL/dH = 5.85 or any quartz particle just slightly less than about six times the largest galena particle may be separated from it. Reference to Eq. 4 indicates that a superior separation between two minerals of differing densities is favored by: (1) coarse particles settling under Newtonian conditions, (2) a large difference in (pa - PL), and (3) separation under hindered settling conditions where p" is high. Of course, there are practical limits to increasing p" excessively because at very high percent solids suspen¬sion fluidity would be lost and the hindered settling separation process defeated. Examples of hindered settling separators are the Dorrco-Fahren¬wald sizer,89 the Rheolaveur box 90 the Spitzkasten,89 and the Willoughby washer.91 These devices make a mineral separation on the basis of both specific gravity and size and all of them are essentially obsolete except for the Dorrco-Fahrenwald sizer and similar devices which still find application for the removal of coarse particles from a much finer particle assemblage and for preconcentration ahead of shaking tables. However, nearly all gravity concentration processes (jigs, tables, flowing film concentrators, heavy media separators) and many sizing devices (sizing classifiers, clarifiers, thickeners, hydrosepa¬rators) make use of the hindered settling phenomenon during the separation of particles. JIGGING Introduction In jigging, a mixture of ore particles, supported on a perforated plate or screen in a layer or "bed" with a depth many times the thickness of the largest particle, is subjected to an alternating rising and falling (pulsating) flow of fluid with the objective of causing all

Jan 1, 1985

By Robert L. Russell

Production at Freeport Indonesia's Ertsberg open pit copper-gold mine started in 1972 at a rate of 7.5 kt/d (8270 stpd). Mill throughput remained at that rate for several years until the discovery of the Ertsberg East (GBT) ore body. This discovery prompted three succes¬sive expansion stages from 1981 to 1988 that boosted production to 20 kt/d (22,000 stpd). In 1988, the discovery of the huge Grasberg porphyry copper deposit launched an era of much larger expansions. The first of these was the installation of a fourth primary mill in 1989 that increased throughput to 32 kt/d (35,270 stpd). That was followed by an expansion of the crushing and screening plant and in 1991 the addition of a new south concentrator to bring production to 57 kt/d (62,830 stpd). The addition of a primary ball mill and the changeout of the original Denver flotation cells in 1993 brought production to its current level of 66 kt/d (72,750 stpd).

Jan 1, 1994

By David Mast, Irwan Halim, Seung Han Kim

Nowadays more infrastructure tunnel projects are procured using design-build method. In this environment, the Owner’s engineer would typically provide performance requirements for the design-builder, and the Contractor’s designer would work with the contractor to design the tunnel lining based on the Contractor’s means and methods and manufacturing process. This paper will describe the typical requirements provided by the Owner based on its design objectives, and the means and methods by the Contractor that would significantly impact the design. Project examples and recommendations for Owner’s requirements will be provided that can optimize the design and still achieve the Owner’s performance objectives.

Jun 13, 2021

By N. R. Sainath

This paper discusses a laboratory investigation that studied the microscale flow characteristics of copper ores and the variation in flow behavior resulting from flow of leach solution. Fractures in 40- and 100-mm-diam (1.5- and 4-in.-diam) cores were first mapped by visual inspection. The permeability of cores to water-stressed in a triaxial stress field representative of in situ conditions - was estimated. The samples were then exposed to 20g/L (2.7 oz/gal) sulfuric acid and the experiment was repeated. The porosity and the rate of recovery of copper from the specimen during leaching were also studied. The measured permeability of unleached samples with no visible fractures ranged from 10-16 to 10-19 m2 and it increased as leaching progressed. The porosity increased significantly with leaching, while the rate of copper recovery decreased.

Jan 1, 1994

By Jamal Rostami, Ataollah Rahbar, Jürgen Paulzen

"Uma Oya Multipurpose Development Project is located in South West Sri Lanka. This project, among many components, involves a 14 km headrace tunnel in very hard and abrasive igneous rocks. The tunnel is under construction by a 4.4 m diameter double shield TBM. The headrace tunnel has already reached 5km milestone and has passed through some reaches of tunnel in very strong intact rocks with no joints. Low penetration at high thrust load has caused frequent stoppages for cutter change leading to low utilization and advance rates due to low cutter life. The original machine was dressed with 27, each 432 mm (17 inch) diameter, 19 mm (3/4 inch) tipped disc cutters. However, various cutter diameters of 432-457 mm (17-18 inch) and cutter tip widths 13 to 19 mm (0.5-0.75 in), have been tried to see if cutter life and penetration rates could be increased. This paper will review the history of the project, the geology of the site, along with TBM performance and cutter life. It will focus on frequency of different cutter failures encountered in various ground conditions. Also, results of using variation of cutter diameter and tip width to cope with the hard rock conditions and their results in increasing machine productivity will be discussed. This allows for better understanding of parameters controlling disc wear/life and leads to better cutter management for more efficient operation of hard rock TBMs in similar conditions. INTRODUCTION The Uma Oya Multipurpose Development Project (UOMDP) lies in the south-eastern part of the central highland region of Sri Lanka. The Multi-Purpose Project Of Uma Oya is planned to convey water from Uma Oya to Kirindi Oya Basin for hydroelectric energy generation includes Puhulpola RCC Dam on the Uma Oya river, Dyraaba RCC Dam on the Mahatotilla Oya river, a conveyance tunnel from Uma Oya to Mahatotilla Oya (L=3750m), a long feeder tunnel from Mahatotilla Oya to Kirindi Oya river. The feeder (or power) tunnel Lot consists of a 15554 m long headrace tunnel (HRT), the surge shaft and tank on the upstream of the vertical shaft, a 650 m vertical shaft with steel lining, and an underground powerhouse and a 3650m tailrace tunnel (TRT)."

Jan 1, 2016

By Gordon M. Pugh, David G. Rasmussen

INTRODUCTION Shrinkage stope mining can be employed in steeply dipping veins where both the wall and the vein material are sufficiently strong to stand with only minimal ground support. Shrinkage stope mining takes advantage of the swell in volume produced in breaking in-place ore. This expanded volume of ore is allowed to occupy part of the mined-out vein, and in so doing provides ground sup¬port and a working surface for the miners. Only enough of the ore is drawn after each stoping cut to allow work¬ing room. Not until the entire mining block has been broken is the full amount of broken ore drawn from the stope. DEVELOPMENT PRACTICES FOR SHRINKAGE STOPING The vein is developed into stoping blocks, each of which is 76 to 91 m (250 to 300 ft) in length and 61 m (200 ft) between levels. Level development, described later, is either on the vein or parallel to it with crosscuts periodically driven over to the vein. There are usually two exits from each stope. The first entry is a raise at one end driven either conventionally by raise climber, or by a raised borehole. Present practice is that this raise, put in from level to level, is either a 2.1- x 2.1-m (7- x 7-ft) Alimak raise or a 1.2- to 1.8-m (4- to 6-ft) diam borehole. Either raise system will require pro¬visions for an ore chute carried with the stope to the haulage level or the scram drift. At 9- to 12-m (30- to 40-ft) vertical intervals, dogholes are developed from the raise so that when stoping breaks back into these dogholes, timber or steel sets and necessary service facilities can be installed. The second entry to the stope may be either a similar raise at the stope endline, or more economically, a cribbed raise carried with the stope. As previously stated, development of the ore block is achieved by either drifting on the vein or by paralleling the vein with a footwall lateral and then crosscutting over to the vein at specified intervals. In the following discussion, three basic cases are illustrated in Figs. 1, 2, and 3. In Fig. 1, development is in the footwall by a 3- x 3-m (10- x 10-ft) trackless lateral. A heading is also driven on the ore and taken either full width or driven a standard size and slabbed to the vein width. Approxi¬mately 9-m (30-ft) long crosscuts on 7.6-m (25-ft) cen¬ters are driven from the lateral to the vein. For ease in muck handling they are usually put in on a slant rather than at right angles. A single orepass, located off the lateral and in the center of one stope block, can serve not only that stope, but also one on either side, up to a tramming distance of not more than 137 m (450 ft). Raises are put at the stope endlines on 91-m (300-ft) centers. The back of the vein is shot down and just enough broken material is drawn off to permit access for men to work off the broken ore. Development in Fig. 2 progresses by driving a 3- x 3-m (10- x 10-ft) trackless heading on the footwall side of the vein. The ore block is delineated by raises on 91-m (300-ft) centers. Crosscuts are again driven on 7.6-m (25-ft) centers over to the vein. Approximately four rounds are then taken up to the vein and each round is successively belled out so that all the crosscuts (pockets, in this case) connect. In this development, as opposed to that in Fig. 1 where there were no belled

Jan 1, 1982

By W. J. Schlitt, K. McNaughton

A heap-leach field test was conducted during the 1993-1994 winter season at Carmacks, Yukon Territory, Canada. The purpose of the test was to demonstrate the viability of heap leaching Carmacks oxide copper ore in an arctic setting on a year-round basis. The test itself utilized a 5-m-diam crib loaded with 250 t of composite ore from the Carmacks copper deposit. The ore was stacked to a total height of 7 m in the crib, including 1 m of ore as an over- layer above the emitter system. This matched the plan for the commercial heap at the time when the test was started. The design also replicated an interior segment of the commercial heap. Leaching was done at a flow rate of 0.2 L/min/m2 using leachate at 21 °C. This temperature was maintained with no external heat input other than normal process heat transferred from electrowinning to the leachate via solvent extraction. Winter conditions were quite typical of those expected at the mine site. The temperature reached -54°C, while averaging -13°C over a three-month period. In spite of some flow system problems, leaching continued unabated, and freezing was limited to the insulating ore over-layer and isolated points near the outer crib walls. Thus, the test demonstrated that year-round heap leaching of Carmacks copper ore is practical in an arctic setting.

Jan 1, 2000

By Henry R. Linden

The demand for natural gas continues to increase at higher than anticipated rates, partly because of its widening price advantage over most other fossil fuels when the cost of air pollution control is included. However, there are clear indications that natural gas supply from the contiguous 48 states and continental shelves will not indefinitely keep up with this rapid growth in demand. Projections are presented which define the extent of potential deficiencies from the 1970's to the year 2000. Among the sources of supplemental gas - imported pipeline natural gas from Canada and Mexico, tanker import of liquefied natural gas, and synthetic pipeline gas from coal and oil shale - by far the most abundant at potentially competitive costs is pipeline gas from coal. The state of development and relative economics of the various coal gasification processes are reviewed. It is shown that synthetic pipeline gas could become a very substantial market for bituminous coal and lignite at current minemouth prices - 60-70 million' tons of coal for each trillion cubic feet of synthetic pipeline gas produced. This corresponds to only slightly more than the current annual increase is gas demand.

Jan 1, 1969

By Joseph A. Whitchurch

The N20 to N25 Tunnel (basic) segment was the second tunnel contract awarded for construction by The PB/MK Team. This project embodied 3.9 km (2.4 miles) of tunnel and was located within the northwest quadrant of the 86.9 km (54 mile) long main collider ring. The contract required the excavation and initial support of a 54.3 m (178 vlf) deep ventilation shaft, a connecting horseshoe shaped Adit and TBM starter tunnel and 3,865 m (12,680 If) long main collider tunnel with a 4.3 m (14 ft) minimum finished diameter. This paper discusses the construction methods, equipment utilized and the production achieved in the construction of the ventilation shaft, connecting adits and the main collider tunnel.

Jan 1, 1995

By J. A. Herbst

In spite of potential theoretical and economic advantages of large-diameter ball mills, many manufacturers elect not to build these mills owing to what is perceived as an excessively large design risk. This risk results from the fact that traditional predictions for mill-scale-up to large diameters are not always accurate. It is apparent that alternative methods of analysis and scale-up are required. Recent studies have shown that detailed population balance models which account for important grinding subprocesses, i.e., grinding kinetics, material transport, and classification, are capable of predicting the performance of small- and intermediate diameter mills (up to 4.3 m (14 ft)) from small-scale batch tests. These same models are used in the current study to predict the performance of a "borderline" large ball mill (4.7x5.5 m) at Asarco's Sacaton operation, a ball mill (5.0x5.8 m) at Kennecott's Chino operation, and one of the world's largest ball mills (5.5x6.1 m), at Cities Service Pinto Valley operation. Model parameters required for scale-up have been estimated in a 380-mm diameter batch mill. Predictions are compared with the results of detailed plant sampling in the three plants. For the Sacaton and Chino operations, the error of the predictions was found to be less than 2.5%, while the corresponding error for the Pinto Valley operation was less than 2.7%. It is concluded that proper representation of the major subprocesses of grinding in the model equation is the key to achieving accurate scale-up. Of special importance is the need to account for the size distribution of the grinding media and the influence of the size distribution environment in the mill on grinding kinetics.

Jan 1, 1983

By T. O. Kuhl

The Royal-Mountain King Project is 7.2 kilometers (4.5 miles) northwest of Copperopolis, California. Reserves of 8,250,000 t (9,100,000 st) at 2.32 g/t (0.068 oz/st) gold will be processed at 2500 t/d (2750 st/d) from three pits. Production is scheduled to begin the first quarter of 1989. District geology consists of northwest trending sequences of Jurassic meta-sedimentary and meta-volcanic rocks. Three ore bodies are located along the Hodson fault which trends northwest and dips 40 degrees northeast. The Gold Knoll and North Pit ore bodies are hosted in carbonate and silica altered meta-volcanic rocks whereas the Skyrocket ore body is hosted in quartz stockwork zones in meta-sedimentary rocks. Gold is present as inclusions and micro-veinlets in pyrite.

Jan 1, 1989