Search Documents

By Enrique Fernández

INTRODUCTION The high speed rail link between Madrid and Asturias, in the North of Spain, has encountered in the Cantabrian range the biggest challenge of the whole line, a very deep tunnel, 25 km long through a foreseen difficult geology. This tunnel was divided in the following four lots for construction: ¦Lot 1: Pola de Gordón- Folledo. L=10,7 km ¦Lot 2: Folledo-Viadangos. L=4,166 m ¦Lot 3: Viadangos- Los Pontones. East tube. L=10,4 km ¦Lot 4: Viadangos- Los Pontones. West tube. L=10,4 km. Dragados S.A. leading a JV was contracted to design and built the Lot 2 on the captioned Pajares High Speed Railway Tunnel. The Lot 2, comprising the middle third section of the 25 km long tunnel has an additional challenge: the construction of one access from the surface to allow it own construction. Feasibility reports and preliminary design do not foresee the use of TBM due to the risk of squeezing ground at the deepest area of the tunnel. On the other hand, conventional NATM excavation of the twin tunnels and ancillary works, including access shafts were against the expected construction schedule by the client, due to the poor ground foresee at the early stage.

By C. D. Litton

Laboratory experiments were conducted to determine the responses of a prototype smoke detector and a commercially available photoelectric smoke detector to smoke particles generated from various combustion sources. The prototype smoke detector combines optical scattering measurements with ionization chamber measurements in order to reduce/eliminate nuisance alarms due to the presence of airborne dusts or diesel exhaust particles. The commercially available smoke detector is designed for use in harsh environments where airborne dust represents a major problem due both to nuisance alarms and detector contamination. In the experiments, the responses of the two detectors were measured when exposed to smoke particles from the exhaust of a diesel engine and from a variety of fire sources, including wood, coal, styrene butadiene rubber, and No. 2 diesel fuel. For the solid fuels, data were obtained for both smoldering and flaming combustion. This report describes the experiments, their results, and the use of these results as they apply to early-warning fire sensors capable of the rapid and reliable detection of fires in atmospheres that may or may not be contaminated by either airborne dust or the products produced from diesel engines. Subsequent to these laboratory experiments, six smoke detectors were installed in an underground limestone mine for further testing and evaluation. DISCLAIMER: The findings and conclusions in this report have not been formally disseminated by the National Institute for Occupational Safety and Health and should not be construed to represent any agency determination or policy.

Jan 1, 2009

By S. Jayson Ripke, Shane Hoff

Cleveland-Cliffs’ Northshore Mining Company operates a magnetic iron ore (taconite) concentrator and pelletizer in Silver Bay, MN. These are two recent cost reduction projects: 1. Rougher Magnetic Separators were upgraded throughout the concentrator; throughput and recovery were simultaneously improved. 2. Green Ball Roll Screens on one agglomeration circuit were upgraded from 3.5-inch to 2.5-inch rolls. Throughput improved by 24% from 62 to 77 LTPH. Green ball size distribution improved as an added benefit.

Jan 1, 2005

By Jean Habimana

Complex and distinct geological units spread along the 7-mile long 30-ft inside diameter Upper Rouge Tunnel CSO Control Project in Detroit, Michigan. Its construction is divided in two tunnel construction packages: The South Tunnel, to be driven in finely laminated weak TG Limy Shale, will be excavated by a shielded TBM with precast concrete segmental lining, while the North tunnel, predominantly in a relatively more competent geologic formation Antrim Shale, will be excavated by a main beam TBM with a two-pass lining system. The adits and deaeration chambers will be excavated by sequential excavation method. This paper addresses the process of selecting excavation methods and lining systems for shafts, tunnels, connecting adits, and deaeration chambers.

By Harry R. Price, Bharat Doshi, Awni Qaqish, Abdul-Ghani Mekkaoui, Thaddeus Znoy, Ramesh Shukla

In 1992, a detailed inspection of the Southfield Sewer revealed a reach of approximately 0.8 kilometers in length, located directly below the freeway lanes, which was severely distressed. Failure of this section of the sewer would result in the closing of the busiest roadway in the state as well as the potential backup of sewage into homes and spilling into nearby surface waters. As such, repair of the distressed section required development of a procedure that would not jeopardize the conveyance of flow through the existing sewer nor impede travel on the overlying freeway. Based on these constraints, the DWSD and NTH team developed a repair concept that entailed the mining of a new, 3.05-meter (10-foot) diameter bypass away from the traffic lanes. The new bypass section was connected to the existing sewer, up stream and down stream of the distressed area, using a “top down” construction approach, that required only minimal freeway closures during weekend periods. This paper, prepared jointly by the Owner, Consultant and Contractor will describe existing conditions, design considerations and construction methods.

Jan 1, 2001

By E. A. Sarver

The Fe(II) regeneration process is an important aspect of Alternate Anode Reaction Technology (AART) for copper electrowinning (EW). In AART, Fe(II) is oxidized to Fe(III) at the anode during EW, and it must be regenerated to maintain recyclable electrolytes. Regeneration is achieved via Fe(III) reduction by SO2(aq), and the reaction is catalyzed by activated carbon particles. To better understand this process, a kinetic model was developed and experimentally validated for the Fe(II) regeneration in the current work. The investigation focused on the primary reaction mechanism and the reaction rate dependence on four variables: carbon particle size, flow rate, initial Fe(III) concentration and initial SO2 concentration. The Fe(II) regeneration reaction is mass-transfer controlled in the presence of activated carbon. Carbon particle size and initial Fe(III) are the most influential factors under the conditions tested. Initial SO2 concentration is insignificant to the reaction rate.

Jan 1, 2007

By C. Sykes, E. Turner, M. Wyart-Remy

This paper follows that of the Milos Conf, 2002 and examines the collection and reporting of SDIs in the industrial minerals industry in Europe. It compares the characteristics of the GRI Reporting Guidelines, with its Metals and Mining Sector Supplement with those of the EU DG Enterprise Scheme, launched in 2001. The particular issue of SME's and companies which are not publicly traded is examined. The pros and cons of participating in such schemes is a central theme of the paper. The paper concludes that there and many business benefits for these companies in participating and submitting their data. The European Commission Scheme is strongly recommended for companies in the sector which are SME's and not-publicly traded as well as large firms who are listed on European Stock Exchanges.

Jan 1, 2005

By Robert Rautenberg, Paul McDermott

This paper will discuss the construction of 15.9 km (9.88 mi) of tunnels on a project in Chicago, Illinois. The tunnels were driven utilizing two rock and four soft ground TBMs ranging in sizes from 7.39 m (24.25 ft) in rock down to 1.95 m (77 in) in soft ground. In addition to the mining, there are 63 upper level structures and 16 dropshafts averaging 61.5 m (202 ft) deep included on this project. Many diverse mining, excavation, support and lining techniques were employed on this project.

Jan 1, 1997

By Dale R. Ralston, Roy E. Williams, Gerry V. Winter, George L. Bloomsburg

The purpose of this section is to demonstrate the development of a method that we believe can be used for simulating and predicting mine water inflow. It will also show how important it is for personnel who model mine water inflow to have considerable experience with this subject, and with the conversion of hydrogeologic frameworks to conceptual models. Several of the models described previously are said to be three dimensional. However, closer examination reveals that there is considerable limitation in the variation possible in the third dimension. A true three-dimensional analysis would require a very large program. Therefore, it seems more reasonable to develop a procedure by which information from a two-dimensional model can be used for analysis of a three-dimensional problem. For a vertical mine shaft this is relatively easy because most two-dimensional models have an option for axisymmetric flow. If it can be assumed that axisymmetry exists about the centerline of the shaft it can be modeled easily as has been illustrated previously. For a horizontal drift or tunnel the analysis is not nearly as straightforward. However, the flow can be divided into two parts as indicated in Fig. 59. Part 1 considers the flow into the side of the drift while part 2 considers the flow into the end of the drift. To calculate the flow rate into the entire drift from the unsteady flow into a unit length the instantaneous flow per unit length may be integrated over the total length of the shaft. This procedure is shown in Fig. 60. The radial flow through any incremental length of the shaft is q. The total flow rate, Q, into the drift at any particular time is given by: The discharge q is a function of the time during which a particular segment has been draining that is dependent on the location x. In other words, a location at x = 0 has been draining during the entire time of expansion while a segment at x = L has only started to drain. Therefore, the time of draining at any point, x, is given by: [ ] where t' is the time over which the mine has been expanded. To determine the relationship between q and t it is necessary to refer to Polubarinova- Kochina (1962, pp. 566-569) and the equation given for the unsteady flow problem. This is: [ ] where q is the steady flow, q,, q, are the coefficients, and t is the time since drainage began. The expressions for q0, q1, and q2 are given as:

Jan 1, 1986

By Hiroshi Soda, Atsumi Ohno, Hiroyuki Yamazaki, Alexander McLean

INTRODUCTION The method of heat removal during a casting process strongly influences the crystal morphology of the cast product and hence the metallurgical and mechanical properties of the solidified materials. In this paper, the Ohno Continuous Casting Process (OCC) is described in terms of the casting conditions and the type of structure observed in the cast product. Significant improvements are observed in workability, fatigue strength and corrosion resistance of castings produced by the OCC method, Ohno (1988). Applications of this technique to low melting point nonferrous metals and alloys are discussed. The feasibility of the application of this technology to high melting point materials is outlined. THE OCC PROCESS The OCC process involves delivering liquid metal into a heated mold, the temperature of which is held just above the solidification temperature of the metal to be cast. This is the key point which differentiates the OCC process from the conventional continuous casting method. A schematic illustration of the OCC process is shown in Figure 1. The Formation of a Single Crystal When the mold is heated above the solidification temperature of the metal to be cast, nucleation on the mold surface is prevented and solidification takes place only at the mold exit. The heat is extracted through the product being cast by a cooling device located near the mold outlet. Crystals are formed only at the tip of the dummy bar at the start of casting, and as the dummy bar travels away with a progressively increasing speed from the mold, the position of the solid liquid interface will align with the mold exit, producing a unidirectionally

Jan 1, 1990

By Bill Elverman

Randy and Kenny Robison have visited every coal mine that would let them in the door, to survey the best mining practices. The brothers have spent nearly their entire lives working in coal operations. The Robison’s started out on lube and grease trucks and worked their way up to respected industry leaders in Alabama. The Robisons have owned MS&R since 1989. Since then, they have created a niche for themselves in providing coal for Alabama’s metallurgical coal market. A great deal of the knowledge the Robisons have amassed throughout the years has come from observing — taking note of what works and what does not. In early spring 2004, they commissioned a Komatsu America PC3000 Super Shovel. Outfitted with a backhoe attachment and a 16-m3 (21-cu yd) bucket, MS&R’s PC3000 is currently one of the largest mining excavators working in Alabama.

Jan 1, 2005

By T. J. Nelson

Natural aggregates, primarily stone, sand and gravel, are recovered from widespread, naturally occurring mineral deposits and processed for use primarily in the construction industry. They are mined, crushed, sorted by size, and sold loose or in concrete products to build roads, houses, buildings and other structures. Smaller quantities are used in agriculture, cement manufacture, and chemical and metallurgical processes. The growth of cities, their buildings and the highways that connect them have created demand for enormous quantities of aggregates. Consumption has now reached 9 t (10 st) per person and continues to grow faster than population. The aggregates industry is the largest mining industry in the United States in terms of production by weight, by volume and by number of active operations. About 80 percent of the concrete pavement and more than 90 percent of the asphalt pavement is composed of aggregates.

Jan 1, 2006

By Kazem Oraee

In underground coal mining, particularly room-and-pillar methods, the coal pillars play a significant role in roof stability. If the pillar dimensions are increased, the pillar bearing capacity also increases, but more coal remains in the pillar and therefore the recovery of mining operation decreases. Therefore, determining the optimum pillar dimension based on technical, economical and performance parameters is important. In this paper, the coal pillar is designed by using the concept of ground reaction curve (GRC). For this purpose, the GRC for coal pillars is drawn and then the elastic and plastic zone of coal pillar behavior is determined. Based on elastic and plastic zone, different equations are presented to draw a pillar reaction curve and the process of coal pillar design based on GRC is explained. As a case study, this new technique is applied to study the coal pillar state in Tabas coal mine of Iran. The results show that the presented new approach is successfully used in the design of the optimum coal pillar dimensions, and also determines the elastic and plastic behavior limit, which is important especially for the logical design of yield pillars.

Jan 1, 2009

By Steve J. Czehura

The Butte quartz monzonite is the host rock for early porphyry copper style mineralization and subsequent mesothermal-epithermal, enargite-gold style veining that transects the district. The east-west Anaconda system veins sustained mining for over a century. They include the Emma, Anaconda-Original, Syndicate, Badger-State and Alice-Rainbow veins, each with strike lengths of more than 3,660-m (12,000-ft) and vertical continuity in excess of 1,370-m (4,500-ft) with mining widths from 1.5- to 15-m (5- to 50-ft). These characteristics are unique to Butte. The incredible dimensions and tenor of these veins have yet to be surpassed and Butte is still touted as being the “Richest Hill on Earth.” The Anaconda Company was formed in 1895 to develop underground copper reserves in the district. It eventually consolidated all operations under one company. Production from underground mining continued through the mid-1970s. Openpit mining in the Berkeley pit began in 1955 with the extraction of supergene ores, along with the remnants of deeper horsetail zones inaccessible to the underground mines.

Jan 1, 2006

By B. K. Blashich

In responding to mine fires and explosions, accurate and timely analysis of the mine atmosphere is critical in making decisions regarding firefighting, mine rescue and mine recovery operations. For many years instantaneous analyses were available to rescue workers using handheld or portable gas detection equipment, including infrared, electrochemical, or catalytic measuring devices for a limited number of specific gases such as oxygen, methane, carbon monoxide and carbon dioxide. Instantaneous sensing technology is not available for all gases, such as nitrogen and hydrocarbons, found in a mine fire atmosphere and cross-sensitivity can be a problem with this technology. For these reasons, air samples are collected for injection into a gas chromatograph for a complete and accurate analysis for all gases including oxygen, nitrogen, methane, carbon monoxide and carbon dioxide, as well as ?fire gases? such as hydrogen, ethylene, ethane, and acetylene. This method requires additional time for transporting the samples to the laboratory near the mine, as well as an instrument operator to inject the samples for analysis. The use of a portable micro gas chromatograph with a continuous and automatic injection system has been implemented by the Mine Safety and Health Administration (MSHA) during mine recovery operations. The device directly samples the mine atmosphere from an underground location every twelve minutes and automatically analyzes the samples for all of the mine fire gases. The portable unit utilizes micro technology and the operating software has been modified to perform the calculation of sample results in and Excel® spreadsheet without user interaction. This paper describes the micro gas chromatograph system and its use at a recent mine recovery operation. The automated remote operation of the micro gas chromatograph has been shown to be a good alternative to infrared and electrochemical sensors used for mine atmosphere analysis.

Jan 1, 2009

By A. D. Nicholson

This paper presents an approach to quantitatively calculate the neutralization of acid by silicate minerals, based on the chemical kinetics of acid reacting with silicates. This approach incorporates incongruent dissolution mechanisms and the effects of silicate iron content on net acid consumption, and offers guidelines for considering the extent to which specific silicate minerals will react. This approach differs from previous methods of estimating silicate buffering: it is based more on the fundamental chemistry of acid generation, and less on potentially misleading empirical measurements of acid neutralization.

Jan 1, 2002

By Moussa Wone

The Washington, DC Water and Sewer Authority (WASA) has implemented facility planning for the Anacostia River Projects portion of a program to bring its Combined Sewer System (CSO) into compliance with federal water quality regulations by 2025. The program includes approximately 19 kilometers (12 miles) of deep CSO storage/conveyance and flood relief soft ground tunnels, construction, vortex drop, overflow, maintenance and air release shafts, as well as near surface diversion structures and conveyances. The Project encompasses major technical and non-technical challenges including completion under a federal consent decree schedule, construction within the confines of heavily developed urban areas, difficult ground conditions, major infrastructure crossings, and close coordination with several major public agencies. This paper discusses the planning stage considerations related to the geotechnical investigation program, discusses obstructions that influenced alignment selection, and provides two examples of preliminary estimates of settlement induced ground movement due to the tunnel and shaft construction.

Jan 1, 2008

By W. H. Dickinson

The performance of seven antiscalants spanning a range of chemistries was evaluated for control of calcium carbonate (CaCO3) formation in gold processing applications. Three preferred chemistries were identified which provided up to 100 percent inhibition in static jar tests when applied at 30 ppm dosage. The three products were further evaluated using a model carbon extraction circuit developed for this application. The test circuit enabled direct measurement of calcium carbonate formed on the carbon from a supersaturated solution under dynamic conditions. The antiscalants lowered CaCO3 buildup on the columns by 15 - 26 percent compared to untreated controls. Impact of the antiscalants on the rate and extent of gold loading onto a carbon adsorbent was evaluated in laboratory carbon-in-pulp (CIP) studies. The antiscalants generated a 25 - 35% increase in gold loading at gold extraction efficiencies up to 65%. On-site testing at a gold processing facility demonstrated that 10 ppm of the preferred antiscalant was able to fully suppressCaCO3formation in thickener overflow water.

Feb 27, 2013

By Y. Breau, F. Robichaud

The Expert System implemented at the East-Malartic mill controls a copper flotation circuit while taking into account the profitability of the operation. Treating a copper gold ore, the flow sheet integrates a flotation step followed by cyanide leach circuit. The Expert System calculates the actual net smelter revenue of the flotation circuit, accounts for the operating cost of the cyanidation circuit and defines optimal metallurgical operating targets to optimize the overall economics. To be realistic, probability factors and circuit diagnostic analysis are integrated in the operating target selection. The Expert System has proved to be successful, robust and flexible. It resulted in a copper concentrate grade increase of 1% while maintaining recovery. The use of the expert system also gives plant personnel good training procedures and promotes interaction with mill operator.

Jan 1, 2002

The technical parametrization of reserves is a technique which has made an important contribution to the definition and the calculation of optimal mining projects. Its applications to a new open-pit optimization program have already been presented in various papers (François-Bongarçon and Maréchal (1976); François-Bongarçon and Guibal (1981)). The present paper gives a brief description of the general problem of parametrizing reserves before going into the details of the practical algorithms used in two typical cases, i.e. open-pit mining and mining between hanging wall and foot wall.

Jan 1, 1982