Search Documents

By D. P. Roberts

The stoping of platinum orebodies in the Bushveld has in the past been accomplished by using in-stope pillars to ensure stability of the workings. In the future, the use of continuous mining machines to mine the platinum orebodies is probable. It is not envisaged that such machines will cut in-stope pillars. This paper describes the alternative support systems that will replace the pillars and the stope geometries that will be required for this type of mining. The paper describes how the support resistance provided by in-stope pillars in current mining was determined and then evaluates support systems that can substitute for these pillars. Conceptual layouts based on existing breast mining layouts are presented. The layouts consist of panels of up to 100 m face length between rigid strike stabilizing pillars. A number of design charts are then proposed that allow for the design of appropriate support systems.

Jan 1, 2005

By D. Chetty

The characterization of platinum group minerals (PGMs) from concentrator flotation circuits provides valuable information towards understanding PGM recovery under given milling and flotation conditions. Additional mineralogical characterization also provides information on ore variability, which may affect recovery. Considering the low grades involved, automated scanning electron microscopy (SEM) characterization of PGMs has enabled relatively quick analyses, compared with older, time consuming and less accurate optical microscopy methods. Over the years, parameters, such as species, size distribution, liberation, gangue and base metal sulfide (BMS) associations, have been used to characterize the PGMs in a process mineralogical context, to aid metallurgical interpretation. This paper considers whether flotation indices determined for PGMs can be empirically validated, using initial results from analysis of PGMs in a concentrate bank from a South African concentrator treating UG2 ore from the western limb of the Bushveld Complex. The aim is to determine whether floatability is adequately described by these parameters, or whether other mineralogical factors must be considered when assessing PGM floatability, and hence accounting for recovery vs. losses to tails. The data obtained to date, show that flotation parameters (including liberation index, BMS/gangue relationships and size distribution) have merits where large changes in PGM concentration occur, as observed in the first four cells of the concentrate bank. Larger data sets, however, are required to assess floatability, particularly where concentrate cell grades are similar, as observed in the last six cells of the concentrate bank. Furthermore, the floatability indices could be enhanced by the incorporation of selected associated gangue mineral information, chief amongst these being the content and mode of occurrence of naturally floatable talc and associated orthopyroxene.

Jan 1, 2009

By S. E. Cook

This article uses the case of the Royal Bafokeng Nation to argue that royalties and dividends from mineral resources, if managed well, can provide direct benefits to the surrounding community even while the state collects its share of mining revenues through taxation. The key to this model is the effective management of the resource income flowing into community coffers. Where some of this income may fund urgent interventions in the community, a portion of the income can also be used to establish an intergenerational wealth fund to meet the needs of future generations. As a depleting resource, minerals like gold and platinum are not a sustainable source of income, and must be replaced over time by more regenerative income streams. These strategies and dynamics are manifest in the Royal Bafokeng Nation?s status as both community and quasi-municipality, a labour hosting and a labour sending community, a mine operator and a mine owner. The Royal Bafokeng Nation also owns one of South Africa?s largest community-based investment companies, which channels revenue derived from platinum deposits into a broad investment portfolio that in turn funds an aggressive social development program for 150,000 people living in twenty-nine rural villages.

Jan 1, 2013

Viscosity measurement was carried out over a narrow range of silica content around the fayalite composition. A wide range of temperature and oxygen potential was covered where the slag was completely liquid. In order to keep the slag composition and the Fe3+/Fe2+ratio constant, theCO2/CO ratio was kept constant as the temperature was varied. Increasing the Fe3+content has little effect on viscosity for slags with a silica mole fraction of 0.31. At higher silica contents, increasing the Fe3+content brings about a small decrease in the viscosity.

Jan 1, 2004

By C. Sawmliana

Deep-hole blasting operations in opencast mines are always associated with some annoyance to the surrounding areas in terms of ground vibration, noise, flyrock, etc. These become more severe when underground mines run parallel to them. Blasting in opencast mines may pose danger to the underground mines in terms of roof/side failures, damage of water dams, isolation/ventilation stoppings and other underground installations. The paper discusses a case study in India on the impact of deep-hole blasting in Ramagundam Opencast Project ? III on the stability of various water dams of GDK-6B Incline coal mine operating in close proximity. The stability of underground water dams of GDK-6B Incline mine was endangered due to deep-hole blasting at OCP-III. There were 15 water dams in seam 3 and 16 dams in seam 4 of the underground mine. The physical strength tests using a Schmidt Hammer instrument were carried out in all the 15 water dams of No. 3 seam and 16 water dams of No. 4 seam. The test revealed that there is a decrease in compressive strength values of three dams of seam 3, namely 6A, 6B and 7. Theose three dams were also directly connected to the water source. Water seepage was also observed from the surfaces of the three dams. However, they were found to be stable in accordance with their design parameters and damage point of view while considering a threshold value of ground vibration as 25 mm/s. It was found that the value of tensile stress generated by a vibration of 25 mm/s was much lower (i.e. 0.171N/mm2) than the tensile strength of the two weakest concrete dams (1.85 N/mm2). Ten experimental blasts were conducted at different working benches of the opencast mine and the ground vibration data were recorded in roof and pillars near various underground water dams. The maximum value of vibration data recorded was 5.9 mm/s in roof near dam no. 1 in seam 3 with the dominant peak frequency of 22 Hz. No adverse effect on either of the dams was observed after that blast. During the period of study, no deterioration/adverse impact was found in any dam of the mine. Based on the results of the study and the analyses of the data, optimized blast design parameters and explosives weight per delay were suggested for the opencast mine to maintain the safety of the underground water dams. Keywords: Opencast blasting, damage, water dams, underground mine, ground vibration

Jan 1, 2009

By A. E. Lewis

The emphasis of this paper is on the characterization and testing of the slag produced by a secondary lead refinery. This work forms part of a broader investigation aimed at reducing loss of valuable product from the process as well as minimizing the environmental impact of the process wastes. It was this work that led to a critical examination of the standard waste classification tests. Characterization of the slag was carried out using a number of complementary techniques. In the broader context, the slag characterization aided in identifying process deficiencies and thus was a critical tool in suggesting potential for process optimization. For this study, the slag characterization provided a relatively comprehensive picture of the composition and properties of the slag, which facilitated understanding the behaviour of the slag under batch test conditions. On the basis of quantity of hazardous components alone, the slag is hazardous according to South African Acceptable Risk Limits (ARL). However, when both the quantity and the leach potential of the hazardous components is taken into account, standard waste tests carried out by three independent agencies indicate that the slag should not be classified as hazardous according to local regulations. Also, according to United States Environmental Protection Agency (US EPA) limits, which are independent of the quantity of the waste, the slag would not be classified as hazardous. The standard waste tests used by the independent agencies was the Toxicity Characteristic Leach Procedure (TCLP), a test which was developed by the US EPA to classify hazardous wastes. One of the requirements of this batch test is that it should be quick, simple to carry out and that the results should be reproducible. Previously, the applicability of the TCLP test to mineral processing and metallurgical wastes has been challenged on a number of points. Additional testing of the slag was carried out using both the TCLP and the Synthetic Precipitation Leach Procedure (SPLP) recommended by the American National Mining Association as being more appropriate for mineral processing wastes. The particular physical and chemical characteristics of the secondary lead slag highlighted additional limitations of both the TCLP and SPLP tests as standard laboratory batch procedures. Keywords: environmental protection, secondary lead processing, slag, leach testing, TCLP, SPLP, ARL, hazardous waste, batch tests

Jan 1, 2000

In surface mining operations, ultra-heavy trucks operate on haul road networks which are typically from 10?40 km in length. These road networks are often not optimally designed and maintained and as a result, identifying and remediating road functional defects is problematic. Most surface mine operators agree good roads are desirable, but find it difficult to translate this into an effective road maintenance system. This paper presents a haul road maintenance management system which utilizes an assessment of rolling resistance based on a functional performance evaluation of a haul road, together with mine haul truck operating cost models to derive the optimal frequency of road maintenance. A typical application is presented which illustrates the potential of the technique to manage maintenance as and where needed with resultant reduction in total road user costs and an improvement in service provided for the road user. Keywords: Haul road, surface mining, road maintenance, transportation, pavement design

Jan 1, 2003

By W. Stumpf

Mean flow stress analyses from plant mill logs for the conventionally produced hot rolled low carbon steel from the Ispat Iscor Vanderbijlpark strip producing plant, indicated a higher temperature sensitivity than that found for the equivalent SAE 1006strip steel produced in the compact strip plant of Saldanha Steel. This was confirmed quantitatively through detailed hot deformation studies on an as-cast structure as well as on a finer grained condition on the same steel. In the conventionally produced steel, activation energies for hot deformation of 309 kJ.mol-1and 388kJ.mol-1for the two respective starting structures were found, both values extending over the entire normal hot deformation temperature range of 1140 to 900°C. These and other experimentally determined constitutive hot deformation constants were applied to the hot rolling austenite grain size development model used earlier. From this, it is predicted that dynamic recrystallization occurs only in the first two break-down passes at the Vanderbijlpark plant and thereafter static recrystallization occurs after exiting from all of the remaining ten or eleven roughing and finishing passes. This is significantly different from what was predicted earlier for the Saldanha Steel plant with its lesser number of passes where static recrystallization is predicted to occur only in the last three passes. The effects of this process difference and other observed product differences between the two types of product are discussed. Keywords: Low carbon steel, hot rolling of strip steel, rolling mill log analyses, austenite grain size, grain size modelling.

Jan 1, 2004

By I. K. Craig, F. R. Camisani-Calzolari

Defects which occur at the surface of a continuously cast slab impede the throughput of final product, because an extra stage in the process is required to grind the defects away before further processing can take place. Defect prediction and the minimization of the occurrence of defects is required. The use of two models to define the defect propagation is explained. Both models are derived using system identification techniques such as auto-regression with exogenous input(ARX). One model is used to determine the effect of manipulated variables such as casting speed and measured disturbances such as mould level on temperatures within the mould. The other isused to determine or indicate the effect of the mould temperatures on the occurrence of defects such as transversal cracks. The latter model can be used to predict when the defects will occur and the former can be used to control the occurrence of the defects. Keywords: continuous casting, surface defect, control system, predictor, system identification, ARX

Jan 1, 2003

By H. Yavuz

Physical modelling is one of the research tools in the understanding of the failure mechanisms and the deformations likely to be experienced by the strata during mining operations. Success of the physical models to predict the strata behaviour depends on satisfaction of the scaling requirements in modelling material used. This paper gives results from a laboratory work carried out into the factors influencing the strength and elastic properties of a physical model material to satisfy the scaling requirements determined from application of dimensional analysis to the pertinent variables affecting the deformation and failure of the underground structures. It was found that the conditions for preparing the material over its composition had a great influence on the final properties. The effect of different water quantities, sand size and mixing time upon the properties of modelling material was studied and water requirement for different proportions of sand/plaster to prepare the material was optimized. Various sand/plaster ratios of compositions were cured at three different levels of oven temperatures. Curing at low temperature produced material within the average modulus ratios ranging from 290 to 432, which are common to most rock types according to Deere?s rock classification, whilst curing at high temperature produced material within the low modulus ratios ranging from 64 to 140 depending on its composition. A combination of low and high temperature curing resulted with an increase in modulus ratio compared to high temperature curing. Curing the material at low temperature compared to other curing temperatures provided a satisfactory range of strength ratio. It has been shown that the relative amount of filler to plaster in the mix controls the frictional properties of the material and results with an increase in strength and modulus ratio of the material provided that suggested preparation and curing conditions were applied. Model material developed by curing at low temperature simulated modulus ranging from 241 to 343 and strength ratios ranging from 11.6 to14.8 of a coal mine rocks, satisfactorily.

Jan 1, 2003

By R. P. Mohring

Before we look at what the challenges and opportunities for future coal mining will be, it is appropriate to have a look at whether there will be a coal industry in the future. There is much talk about the damage caused by the burning of fossil fuels and the need to replace coal and oil with more environmentally friendly energy sources. Yes, there is evidence that the current practice in burning of fossil fuel has certain negative environmental effects, however, the adverse effects for global economic development from inappropriate measures to control greenhouse gas emissions would be severe.

Jan 1, 2001

By U. Sachse

This paper explores a systematic approach for mining decision-makers to use when faced with choosing which method to use for a specific rockpass length. The different excavation methods available in the broad South African mining industry are compared against a number of critical parameters, as applied to rockpasses of varying length. This approach is not meant as a definitive, prescriptive planning tool, but rather as a proposed approach to enable designers and planners to choose the best system to excavate their specific rockpasses

Jan 1, 2005

By Ravichandar. D., K. B. Nagashanmugam, M. S. Pillai

"Blast furnace performance depends strongly on the coke reactivity index(CRI) and coke strength after reaction (CSR) properties. An innovative and cost-effective method, known as the Salem Box Test, has been developed to prevent the mass production of inferior coke unsuitable for blast furnace use. This method consists of coal carbonization on a micro-scale and involves charging approximately 18 kg of coal blend in a stainless steel box, carbonizing it together with coal cake in the plant coke ovens, and testing the coke produced for CRI and CSR to determine its suitability for blast furnace use. Only coal blends that yield coke with CRI <25% and CSR >64% are permitted for mass production, and other coal blends are either rejected or the blending ratios adjusted in an attempt to upgrade them. The experimental results reveal that, for a given coal blend, the quality of coke produced by the Salem Box Test is comparable with that produced by bulk production, indicating that the test is acceptable as a screening tool for regular use. The present paper describes the methodology and application of Salem Box Test to predict the suitability of coke for blast furnace use at JSW Steel Limited, Salem Works (JSWSL), and illustrates its advantages in adjusting the coal blending ratio to produce superior coke, in detecting coal contamination, and in preventing bulk production of inferior coke."

Jan 1, 2015

By I. Jones

Geologists, engineers, technicians and surveyors have successfully utilized technical software in the mining industry for over 30 years. Software for processing survey, geology, mine engineering and planning information make these functions more efficient by automating repetitive tasks and reducing data processing errors. While these systems have been improved incrementally overtime, new systems that represent giant leaps in technology have been introduced to help mining operations increase productivity and reduce costs. However, their widespread use within the industry has left individual companies without a competitive advantage. Additionally, the ability of these applications to provide the productivity improvements required in today’s uncertain market conditions has since peaked. The next wave of technology—integration of independent software applications—is just starting to emerge and will have a significant effect on the productivity of mining operations. To reap the productivity gains required to remain competitive, mining companies must exploit the collective knowledge and experience of every employee in the organization. Integration of independent software application allows companies to leverage information from all activities, enabling staff to make better decisions to improve productivity. This paper outlines the importance of integration as productivity enabler. Key performance indicators, strategic mine planning, resources management and mine-to-mill integration are discussed as processes that enable productivity. The Gemcom Enterprise Mining System (GEMS)is introduced as the industry’s first integrated solution that enables these productive processes. The paper concludes with a comment on the level of change required to realize the benefits of integration.

Jan 1, 2003

By R. M. Whyte

The Konkola Deep Mining Project (KDMP) seeks to exploit the deep level potential of the Konkola Deeps orebody, producing high grade copper concentrates for treatment at the Nkana Smelter and Refinery. As an alternative to smelting, Konkola Copper Mines (KCM) has examined a processing route involving pressure leaching of the Konkola concentrates at Nchanga, with the leach liquor being treated by solvent extraction and electrowinning to produce high purity copper cathode. The solvent extraction circuit would be operated to achieve a high ?delta? copper, thereby providing a strong acid raffinate which can be used in the existing Tailings Leach Plant (TLP) to treat Nchanga oxide copper materials. The main focus of the hydrometallurgical option is to capitalize upon the synergy that exists between the treatment of sulphide copper concentrates (acid producing) and oxide copper ores (acid consuming). The paper discusses the key features of a comprehensive piloting campaign carried out at Anglo American Research Laboratories, which involved the co-treatment of Konkola copper concentrates and Chingola refractory ore in a fully integrated pilot plant circuit.

Jan 1, 2001

This paper reviews ore pass practice in some Canadian mines in Quebec and Ontario. In particular it reviews ore pass configuration, flow control mechanisms and monitoring practice. A review of the type of problems encountered and the tools to restore flow is also presented.

Jan 1, 2005

By S. Sarac

In this study, graphical and mathematical methods used to determine operating points in single or multiple fan ventilation systems are summarized. The problem is mathematically formulized for parallel connected fans in which analytical solutions are not possible. For n number of parallel connected fans, a non-linear equation system that consists of n number of non-linear equation sis derived. The Newton-Raphson method, which is a numerical analysis method, is adapted to solve this non-linear equation system and the solution steps are given as an algorithm. A computer program based on this algorithm is written and its applicability is proved.

Jan 1, 2000

By M. Nyoka

Consideration of the economic, environmental, and social impacts associated with the life-cycle of a technology is of increasing importance for decision-making in industry. It has been suggested that economic assessment of technology deployment projects requires the translation of associated environmental effects into monetary values. This paper introduces an approach for identifying and evaluating environmental damage in monetary terms. The approach groups the environmental impacts associated with a technology life-cycle system into four main criteria: air, water, land, and mined abiotic resources. The valuation of the impacts on the resources consists of an economic cost benefit analysis (CBA) procedure that comprises four steps: the compiling of an impact inventory, a monetary valuation of the inventory, discounting, and a risk/uncertainty analysis. The monetary valuation step for impacts on air resources is primarily based on published externality costs for Europe and the United States, which are adopted and converted to reflect the South African context. Local opportunity costs are utilized for the other resource criteria. The damage costs are transformed into South African Rand at 2005 prices. The paper demonstrates how the approach may be applied in the assessment of projects in the metallurgical industry. Shortcomings in the approach are identified. For example, not all of the aspects that are considered necessary to assess environmental performances comprehensively can be valued in monetary terms. Also, certain values, specifically those pertaining to opportunity costs, need to be determined on a case-by-case basis. Furthermore, the uncertainties associated with the indicators obtained may strongly influence the usability of the results of an environmental performance assessment, e.g. future damage costs will change with fluctuations in the markets. It is concluded that although such an approach has merit in increasing the understanding of the potential financial implications of a technology?s environmental performance, further research is required to improve the approach described if it is to be used further in the South African metallurgical industry. Damage cost estimates that are specific to South Africa need to be developed to reduce uncertainty, and the combination of both quantitative and qualitative approaches is recommended for comprehensive sustain-ability decision-making.

Jan 1, 2007

By A. Sariisik

This study analyses the results of a pilot trial of a newly developed armed-chained stone-cutting machine. The machine was developed in Turkey and trialed at the Kaklik/Kocaba travertine quarries in the Denizli District. An armed-chained cutting machine is an alternative to the diamond wire cutting method more frequently used in the production of natural stone quarry blocks, and increases production efficiency and quality. Since there is no need to collapse the blocks using the armed-chained cutting production process, there is no risk of the block developing cracks. This results in a considerable increase in the efficiency of natural stone block production. The armed-chained cutting machine is easier both to assemble and run when compared to other block cutting methods. This process resulted in the production of a larger number of blocks at a lower cost within the same time frame, particularly in travertine quarries and in all other natural stone quarries. The block efficiency in travertine quarries was calculated as 65?80%using the armed-chained cutting machine, compared with 7?14% using the normal diamond wire cutting method.

Jan 1, 2010

By J. Gómez-Hernández, P. K. Kaiser

Abstract The process of stress-induced fracturing around underground excavations in brittle rock is associated with dilation or volume increase of the failed, fractured rock. Different attempts to account analytically for this dilation have been made within the framework of plasticity theory. This theory has been developed mostly for metals, strain-hardening materials or soils, but brittle failure of rock-like materials is characterized by strain-softening behaviour and the volume change is dominated by geometric factors, which may violate stability principles of plasticity. In this work a semi-empirical Rock Mass Bulking Model (RMBM) was developed, using as starting concepts: dilation angle, plastic strain rates, effective deformation modulus, effective Poisson&apos;s ratio, Griffith locus, and the definition of a bulking factor BF introduced by Kaiser et al. (1996). The model was calibrated in order to obtain bulking factors that are consistent with experimental data and case studies of measured bulking around underground excavations. Résumé La fracturation provoquée par le stress autour des excavations souterraines dans le minéral friable est associée à la dilatation ou à l’augmentation du volume de la roche en rupture. Dans le cadre de la théorie de la plasticité, différents essais ont été faits dans le but de trouver une justification analytique pour cette dilatation. Cette théorie a d’abord été élaborée pour les métaux, les matériaux ou les sols d’écrouissage, mais la rupture fragile de matériaux d’aspect rocheux est caractérisée par un comportement d’amollissement et le changement de volume est dominé par des facteurs géométriques, ce qui pourrait ne pas être conforme aux principes de stabilité de la plasticité. Dans le présent ouvrage, un Modèle semi-empirique de masse rocheuse a été élaboré, dont les concepts initiaux sont les suivants : angle de dilatation, vitesse de fluage plastique, module effectif de déformation, coefficient effectif de Poisson, locus de Griffith, et la définition d’un facteur de foisonnement FF apportée par Kaiser et al. (1996). Le modèle a été calibré afin d’obtenir des facteurs de foisonnement qui soient conformes aux données expérimentales et aux études de cas sur le foisonnement mesuré autour des excavations souterraines. Kurzfassung Der Prozess von Brüchen in unterirdischen Abgrabungen in sprödem Gestein ist mit der Ausweitung oder der Volumenzunahme des gebrochenen Gesteins verbunden. Verschiedene Versuche im Rahmen der Verformbarkeitstheorie haben versucht, diese Ausweitung analytisch festzustellen. Die Verformbarkeitstheorie wurde hauptsächlich für Metalle, kalthärtende Werkstoffe oder Böden entwickelt, da sprödes Versagen von Gestein ähnlichen Werkstoffen von kaltenhärtendem Materialverhalten gekennzeichtnet ist, und die Volumenveränderung von geometrischen Faktoren beherrscht wird, die die Stabilitätsprinzipien der Plastizität übertreten. In dieser Arbeit wurde ein halbempirisches Rock Mass Bulking Model (RMBM) (Modell für das Aufgehen der Gesteinsmasse), entwickelt, für das die folgenden Anfangsprinzipien benutzt wurden: Ausweitungswinkel, plastische Fliessensätze, wirksames Verformungsmodul, leistungsfähiges Poissons Verhältnis, die Griffith Ortskurve und die Bestimmung eines Aufgehensfaktor BF1 der von Kaiser et al. (1996) eingefürt wurde. Das Modell wurde so kalibriert, dass es die Aufgehenfaktoren erzielte, die mit den Vesuchsangaben und den Fallstudien von Aufgehensmessungen in unterirdischen Abgrabungen übereinstimmen.

Jan 1, 2003