Search Documents

By N. A. Barcza

This paper describes the development of large-scale thermal-plasma systems, which was motivated, in general, by the potential cost savings that could be achieved by their use as a replacement for the more conventional methods used in the generation of thermal energy. The anticipated cost savings arise not only from the use of plasma-generating devices but from the manner in which they have been interfaced with a furnace to process particular materials, mostly as fines. Thermal-plasma systems fall into two categories: non-transferred-arc and transferred-arc devices. In general, transferred-arc devices have been interfaced with open-bath furnaces in which melting or smelting processes carried out, while non-transferred-arc devices have normally been applied to shaft furnaces. Water-cooled transferred-arc devices are somewhat limited in power (about 5 MW) because of the relatively voltages (300 to 500 V) that can be attained in open-bath furnaces, where very long arcs are undesirable, and because only relatively low levels of current can be carried. Graphite electrodes can overcome the restriction current, and power levels of 30 to 50 MW seem feasible, even with one electrode, if direct current is used. Multiple water-cooled devices are capable of attaining similar power levels, but the capital costs are much higher. Costs due to electrode wear are lower for water-cooled systems, but expensive gases are needed for transferred-arc devices. Mintek conducted extensive pilot-plant work in which water-cooled devices were used initially but graphite electrodes were used subsequently to produce ferochromium from fines. Transferred-arc open-bath configurations were used. This work led to a decision by Middelburg Steel & Alloys (MS&A) to install a 16 MVA furnace of semindustrial scale to produce ferochromium aloys based on the ASEA d.c. arc furnace developed for the Elred process. Non-transferred-arc devices have atained reasonable scale-up to the 6 to8 MW power level, and high-voltage operation, which is inherent in such devices, has enabled lower currents to be used. Nevertheless, multiple systems are still necessary to accommodate large-scale applications, and this can be costly from a capital point of view. The cooling requirements are large, and can represent a considerable loss of electric energy. Shaft furnaces equipped with non-transferred-arc devices are suitable for the processing of materials that have volatile species, e.g. silica or manganese, or where the shaft is used to prereduce oxides that are amenable to gas-solid reactions. It is probably in the treatment of light and refractory metals that plasma technology will achieve its greatest development in the years to come. The energy requirements for the production of these metals are high, and very low oxygen potentials are necessary. These are factors that favour thermal plasma. Much developmental work is still needed in this interesting field. It should be remembered that electrically generated thermal energy is a unique temperature source that, in many instances, cannot be replaced technically or economically by the combustion of a fuel.

Jan 1, 1986

This paper illustrates the application of numerical modeling methods, in conjunction with limit-equilibrium techniques, to the location of critical slip surfaces in slope-stability problems. Initially, the Spencer slice-based method of analysis is introduced, together with a dynamic-programming algorithm for slip-surface location. This limit-equilibrium method is assessed critically through the use of an illustrative problem. The technique is then extended to locate the critical slip surface for a similar slope, but with more complex constitutive and yield relationships for the material comprising the slope. To this end, the use of the stress field generated from a finite-difference program, together with a dynamic-programming search routine, is presented as an advanced technique of slope-stability analysis for engineers.

Jan 1, 1993

By R. M. Stroh, D. F. H. Grave

In this paper ventilation planning methods are discussed, with particular reference to the application of computer techniques to the solving of the many problems associated with the forecasting of ventilation and refrigeration requirements in mines of high production rates going to depths and rock temperatures higher than previously experienced. The use of the Starfield-Dickson programmes for calculating heat flow into airways and advancing stopes is demonstrated in the case of ventilation planning on a large mine extending to a brief depth of over 3 km below the surface. The possible effects of new mining methods on ventilation requirements in the future is briefly discussed.

By deur R. R. Mears

The expected curtailment of activities within the gold-mining industry by the closure of the more marginal mines, and the shortening of the life of the industry as a whole as a result of rising costs and/or an uncertain gold price, are factors that are bound to harm the South African economy in a number of ways. The industry has no option but to regard the gold price, which is determined on the world market, as a given quantity. The remaining ore reserves al tend to be of a lower grade and/or to be found at greater depth. Therefore tighter control of working costs would seem to be almost the only option open to the industry. Working costs can be divided into two broad categories: costs emanating from the environmental characteristics of the orebody, and costs emanating from the general inflationary environment in which the industry has to purchase its inputs. Working costs stemming from the physical environment also fall into two categories: those relating to the grade of the orebody, and those resulting from working at increasing depth and temperature, together with the need to pump increasing quantities of water. The industry is both capital- and labour-intensive in absolute terms, since it requires large inputs of labour as well as of capital. It is limited in its scope to adjust its production function by becoming more labour- or more capital intensive, and is dependent on a large labour force, which cannot easily be replaced by capital inputs. On the other hand, large amounts of capital are required for investment in shafts, development, machinery, and equipment. Since the early seventies, the working costs of the South African gold-mining industry have increased at an annual rate that was significantly higher than the general rate of inflation. This rapid rise in working costs has caused some mines to find themselves in a difficult profit position. At times, the gold-mining industry has even been compelled to restructure its cost/revenue relationship rather fundamentally by revising the grade of ore worked sharply upwards or downwards, as the case may be. The rise in the gold price since 1972 has made it possible for the industry to introduce significant changes in its Black wage policy. The main aim was to increase the permanency of the Black labour force and to encourage local Black workers to join the industry. At the same time, significant increases were also experienced in the cost of machinery and stores, as well as of capital, mainly as a result of inflation. In the study on which this paper is based, the author attempted to measure the influence of environmental factors on working costs, using the physical consumption of electricity as a criterion for measurement. He found that the usefulness of this criterion in relation to factors such as depth, temperature, and water quantities pumped was invariably more than neutralized by the effects of greater productivity and economies of scale. The effects of these environmental factors on the working costs of the industry could therefore not be determined to any degree of accuracy. It seems that good progress is being made with the development of capital-intensive forms of technology aimed at coping with rapidly rising working costs and other effects of increasing depth. Techniques are also being developed to improve rock-cutting procedures and to eliminate the use of explosives in order to introduce a continuous mining process. On the whole, the gold-mining industry seems to be more sensitive to general inflationary pressures than to the cost effects that are associated with depth, temperature, and water quantities pumped. Greater control is possible over physical environmental factors such as the grade of ore mined, temperature, rate and nature of development of a mine, and adaptation of the daily working cycle to a continuous mining process. Wolfe and others hold the view that the industry will lose control over labour costs as a result of the 'sharp increase in wages and the growth of Black trade unions. However, the use of more capital-intensive technology will allow the industry to reduce its labour force, and a smaller, better-trained, and more permanent labour force will enable the industry to cope with the increasingly difficult physical environment and higher wages.

Jan 1, 1987

By N. Kernahan, T. Zaniewski

Threshold blasting involves the use of small amounts of high explosive to break and fragment hard rock without having to evacuate mining personnel. The method is easily assimilated and effective in rockbreaking, but requires rigid control on drilling, charging and timing. Current underground trials are aimed at fine-tuning the amount of explosive energy and blast hole geometry to allow the firing of multiple sets of shot holes in a continuous manner. Through correct procedures, the after-blast fumes, dust and fly rock can be contained so as to provide a safe working environment. Threshold blasting hugely reduces the volumes of explosives used in mining and brings to maturity the potential of the process begun by Alfred Nobel when he introduced nitroglycerine, and later dynamite, to mining. Its key contribution is its enabling of continuous mining operations with well understood and relatively low cost technologies. The use of batch blasting, employing large burdens holds the greatest potential for delivering high flow rates of ore at minimal cost. There is good potential for rapid evolution of the concept.

Sep 1, 2001

By J. A. Ryder

A high proportion of damaging rockbursts are thought to be underlain by seismic events that represent shear or rupture along planes of weakness (faults, joints, dyke contacts). Such events are controlled by shear stresses and friction properties along the plane. Excess shear stress (ESS) is a measure that can be evaluated numerically and that, in principle, can be used in an assessment of the possible magnitude and relative likelihood of seismic activity. Methods for the calculation of ESS in practical mining contexts, and for the estimation of the magnitudes of possible seismic event progressions, are briefly reviewed. The effects of variables such as depth, stoping width and, in particular, virgin horizontal stresses on general shear-type seismic hazards are investigated. Attempted back-analyses of two large rockbursts are described.

Jan 1, 1988

By M. Akyüzlü

The equilibrium between carbon-saturated Fe-Cr-Si-C alloys and SiO2-CaO-MgO-A2O3-CrO2-FeOy slags was studied under atmospheres of argon and carbon monoxide at temperatures of 1500 and 1600°C. The equilibrium distribution of chromium, silicon, and iron between the slag and the metal phases was determined for different compositions of both phases under different atmospheres and temperatures. It is shown that silicon transfer from the slag to the metal increases with increasing temperature, decreasing carbon monoxide partial pressure, decreasing carbon content of the metal, increasing chromium-to-iron ratio of the metal, increasing silica content of the slag, and decreasing lime-to-alumina ratio of the slag. Some activity calculations were made for the experiments conducted at 1600OC in a carbon monoxide atmosphere. It is also shown that a decrease in the iron content and an increase in the slag basicity decrease the chromium content of the slag. A major proportion of the chromium present in the slag was found to be in the divalent state under the highly reducing conditions prevailing in the experiments. The chromous capacities of these slags were calculated and were found to decrease with increasing basicity.

Jan 1, 1992

By G. Voiloshnikov, P. Koblova, Ye. Musin

Preg-robbing activity of the carbonaceous matter negatively impacts the process of precious metals recovery from gold-bearing ores and concentrates. In this paper, ore heap leaching (HL) using a blinding agent which inhibits ‘preg-robbing’ is a promising method. A carbonaceous ‘preg-robbing’ gold ore with head gold grade of 1.92 g/t from a Russian deposit was studied. Corg was 1.12%. In accordance with the Irgiredmet technique, preg-robbing activity was 65.3%. Surfactant reagent DN was used as the blinding agent. Column tests on the ore HL were conducted using two options. They were: a conventional flow sheet (Column 1) and a flow sheet with the reagent addition (Column 2). Gold recovery in Column 1 was 55.39% while gold recovery in Column 2 was 68.48%. The test results confirmed the efficiency of reagent DN. Keywords: Carbonaceous ore, organic blanking, preg-robbing, recovery

Jan 1, 2020

By L. A. Vermeulen, D. D. Howat

New distribution functions are derived to describe the size distribution of grinding elements in ball mils. The formulations are based on the assumption that abrasive as well as impactive interactions occur during bal milling-an assumption that is supported by a large body of experimental evidence. It is shown that the functions can be used in the estimation of the magnitudes of abrasive and impactive components in the total rate of bal wear. The relative magnitudes of the wear components provide a basis for optimization of the chemical and metallurgical properties of the balls in a given milling situation. However, it is contended that these quantities are also useful indicators of the relative intensities of the abrasive and impactive interactions that are operative in the size reduction of mineral particles within ball mils. These quantities can be determined for any industrial ball mil, and their magnitudes provide practical guidelines for mil operation. The theory is used in an analysis of samples of ball charges from two industrial ball mils, and it is also applied to al the data on bal-size distributions found in the literature. The qualitative correlation between the calculated values of the wear components and the reported operating conditions is good for a variety of industrial ball mils, in conformity with the hypothesis that the relative magnitudes of the wear components are related to the milling conditions.

Jan 1, 1986

This paper considers the probability of the occurrence of potential rockfals in deep-level gold mines where there is point support (props, pipesticks, and timber sticks). The investigation described gave rise to the following implications: natural joints subparalel to the direction of strike have a controlling influence on the potential occurrence of rockfals; with discrete types of support such as props at typical sparings, there is a significant probability of the occurence of potential rockfals; the use of headboards oriented in the direction of strike reduces the probability; and loss of support from a prop increases the probability.

Jan 1, 1989

From a consideration of the functional requirements of a stope-support pack, simple design principles were developed. The material and dimensional properties of the different components of the pack were determined from a series of laboratory tests. The most important requirement for an adequate pack is that the cushioning layers of timber between the concrete brick layers should provide sufficient transverse reinforcement. The tendency of the compressed timber to creep is shown to be a serious limitation to pack performance and must therefore be an important consideration in the overall design of supports.

Jan 1, 1978

By H. A. Uys

The metallurgy of tin smelting In a submerged arc furnace By H. A. UYS, Ing. Metallurgy (Pretoria) (Visitor) The control of tin smelting demands a knowledge of slag characteristics and of the equilibrium reaction that governs the process. These factors are explained by reference to the tin-smelting operation at Iscor, Vanderbijlpark. In the primary cycle, it is important to obtain the highest possible FeO content in the slag. In the secondary cycle, a primary slag high in FeO gives a hardhead (iron-tin alloy) high in iron, which is essential if a high ratio of FeO to SnO is to be obtained in the secondary slag. This determines the economy of the smelting operation: the iron that is introduced into the system from the ore concentrate must go out in the secondary slag. Additions of lime are necessary in the secondary cycle but must be limited if the volume of slag is to be kept Iow.

Jan 1, 1977

By W. F. A. T. Meihack

The scope of this paper is confined to gas-fluidized beds in pyrometalurgical applications. After considering the general characteristics of these fluidized beds, the author deals with their potential applications, using the following processes, which are currently under investigation, as examples: pretreatment of chromite, prereduction of manganese-ore and iron-ore fines, roasting and prereduction of ilmenite, and roasting and pyrolysis of gold-bearing pyrite. He concludes that fluidized beds are potentially of great benefit to the metallurgical industry, although much developmental work remains to be done.

Jan 1, 1986

By D. J. C. Taylor, R. A. Kruger

Unbridled mining operations can have a serious negative impact on the surroundings. With the recent increased awareness of the need for environmental conservation and the resulting advances in environmental control, the mine planner has new tools at his disposal for the successful implementation of mining projects while avoiding negative environmental effects. This paper discusses the environmental strategies adopted in the planning and commissioning of a trial underground coal mine. The minimization of negative environmental effects is demonstrated and, where applicable, environmental benefits are examined.

Jan 1, 1986

By D. W. Dean, J. A. Ryder

"A computer system designed to assist in maintenance scheduling and costing, and in monitoring the performance of equipment, is described. The emphasis is on the information retrieval and implementation aspects of the system.INTRODUCTIONThe cost of the maintenance of equipment can account for a substantial proportion of the total costs of any large industry. These costs are made up of the following elements:(i) capital expenditure,(ii) maintenance labour,(iii) maintenance spares,(iv) maintenance overheads,(v) production losses.Control of these cost elements cannot be achieved without a system which maintains and retrieves the necessary infor¬mation efficiently.The system should provide engineering management with the information necessary to:(i) establish the cost of maintaining items of equipment,(ii)establish the economic life of equipment,(iii) determine breakdown patterns for the establishment of optimum inspection, service and overhaul frequencies,(iv) establish work schedules for those responsible for the maintenance of equipment,(v) establish the optimum maintenance labour complement,(vi) establish the optimum stockholding of maintenance stores items,(vii) improve the performance of equipment,(viii) justify the selection of a particular type and make of equipment,(ix) establish the reasons for any abnormal usage of materials and labour, and to(x)reduce the dependence on the human element for the control of equipment maintenance activities.Many industries have comprehensive and numerous equipment maintenance records but they experience great difficulty in retrieving the required information in the time available and with the labour available. Many industries do not bother to maintain meaningful records, because of this difficulty."

Jan 1, 2014

By Penswick D.

From the perspective of management control, most mining operations can be represented by a hierarchy comprising four layers. The base of this hierarchy consists of the individual pieces of equipment that are used to break and transport rock. The next level comprises the coordinated interaction between different pieces of equipment, termed a process. An operation results from the bringing together of different processes within a common discipline, such as mining or hydrometallurgy. Finally, an enterprise is formed when the separate mining, concentrating and smelting business units are combined. To date, much of the literature written on the topic of mining automation has focused on the equipment level, specifically on removing the operator from production mining equipment. This focus should not, however, overshadow advances registered in automation at both the process and enterprise levels. Only at the operations level of the hierarchy has little progress been made. While automated equipment, process management and enterprise resource planning are a current reality; it is argued that the benefits from automation have, to date, been largely elusive. It is further argued that full benefits of automating other levels will only be fully achieved when this ‘gap’ in the mining automation hierarchy has been addressed and an uninterrupted, process-wide information flow across the entire operation is achieved. Furthermore, it will be reasoned that so-called vertical integration can only be achieved with an automated operational level in place. It is believed that all the necessary building blocks are in place and that the industry is ready for this development. The paper concludes by presenting a vision for what operational level automation would achieve.

Sep 1, 2001

By H. S. Eisner, J. -P. Leger

Published South African fatality and injury statistics for mine accidents are investigated. Where possible, the South African statistics are compared with those of other countries. Commonly held attitudes to the South African accident experience are also examined. Analysis reveals that the published accident rates present a more favourable picture than the rates actually experienced by underground workers. In addition, fatality rates in South African underground gold and coal mines do not differ significantly and have remained stable over the past decade, although the injury rates have decreased rapidly. No evidence was found that this is due to improved safety, and a comparison with international fatality and injury data suggests that it is not. The underground fatality rate for South African coal mining is, on average, eight times that of the UK, four times that of all EEC coal mines taken together, and over double that of the USA. Despite the unreliability of the injury rates, much has been made in South Africa of their rapid decline, an emphasis that appears to be misplaced.

Jan 1, 1988

By J. H. Venter

This paper contributes towards the solution of the problem of characterizing the accuracy of estimation of ore quality based on a random sample from the ore bulk.

Recent advances in the design and performance of flotation equipment A General Meeting and Colloquium on the above topic was held on 12th March, 1975, at Kelvin House, Johannesburg. The Colloquium was attended by 250 delegates and was opened by the Immediate Past President, Mr P. W. J. van Rensburg, at 09h30. Obituary Mr Van Rensburg announced with regret the deaths of James Alfred Boyd, Life Fellow, and Jack Joseph Frankel, Fellow. Training of technicians The Institute has received a letter from The Federation of Societies of Professional Engineers pointing out that there is considerable opportunity for the training of Coloured and Bantu technicians and artisans, and that the existing facilities will be extended as the demand for them increases.

Jan 6, 1975

By Karl-Heinz Obst, Juergen Stradtman

The importance of the chemical and physical properties of lime has been overlooked for years although the quality of lime plays an important role in the production of steel. With the introduction of the oxygen injection process these properties have been re-evaluated. The CaO, MgO, S, and P2O5 contents of lime are important, but so are the physical properties such as granulation, reactivity with respect to slag formation, and the degree of burning. Soft burnt lime enhances de-phosphorisation and de-sulphurisation, and facilitates the smelting process in general, mainly due to its large specific surface. Special lime, prepared as briquettes from quicklime and fluxes or as pellets from limestone and various fluxes with or without binding agents, clearly accelerates lime dissolution during the slag formation process, lowers the melting point, and enhances de-phosphorisation, de-sulphurisatlon, and de-carburisation even more than soft burnt lime. The introduction of special limes in the oxygen injection process for steel production has opened up new fields for commercial exploitation of slags as well as improved operational techniques.