Search Documents

The following contributions were received to the paper entitled 'Safety in South African mines: An analysis of accident statistics', by H.S. Eisner and J.P. Leger, which appeared in the J. S. Afr. Inst. Min. Metal., vol. 88, no. 1, Jan. 1988, pp. 1-7. Contribution by H. WAGNER* The paper by Dr H.S. Eisner and Mr J.P. Leger is critical of the safety situation on South African mines and portrays the industry as having little concern for the health and safety of its workers. Moreover, the casual reader gains the impression of deliberate misinformation by the industry to the public concerning safety maters. Furthermore, certain socio-economic reasons are advanced for the apparent differences between the fatality and injury rates reported for coal mines in South Africa and those for the United Kingdom. Contribution by S.A. WATTS. Authors Eisner and Leger are to be commended on their paper, which highlights, according to their interpretation, various shortcomings of both the Chamber of Mines accident statistics and those published by the Department of Mineral and Energy Affairs. Authors' Reply We gratefully acknowledge Dr Wagner's contribution to the discussion on our paper. For convenience, we shal use his sequence of comments in our reply. Before doing so, however, it may be useful to explain how our paper came to be written. After the explosion at Hlobane Colliery in 1983, one of us (HSE), in February 1984, was retained by the lawyers acting for some of the dependants of the victims to advise on technical maters relating to the explosion. Contribution by Ms S.A. Wats Some of the points made by Ms Wats have already been answered in our comments on Dr Wagner's contribution. We are fully aware that the number of accidents leading to absences of less than 4 days would be much greater than shown in our bar chart, and are grateful to Ms Wats for drawing attention to the specific exceptions that can make a 1-3 day accident compensable and that are clearly responsible for the relatively low count in that category of the chart.

Jan 1, 1988

Limestone formations in the United States can be subject to relatively high horizontal stresses due to the existence of tectonic loading of the limestone strata. Underground limestone mines use the room-and-pillar method, in which 12- to 18-m-wide rooms are typically excavated. The stability of these excavations can be compromised by the horizontal stress, resulting in a rockfall hazard. Rockfalls are the cause of 15% of all reportable injuries in underground limestone mines. Horizontal stress related damage can occur in the form of guttering along one or more sides of an excavation, roof beam buckling or oval shaped roof falls, with the long axis perpendicular to the major horizontal stress. Numerical analyses show that the pillar layout and orientation of the mine workings have an effect on the horizontal stress distribution within the roof. The effects of high horizontal stresses can be mitigated by orientating the heading development direction parallel to the maximum horizontal stress, reducing the number of cross-cuts and offsetting the cross-cuts to limit the potential lateral extent of horizontal stress related roof falls. The modeling approach described in this paper can be used as a tool to evaluate potential roof failure and optimize the stability of room and pillar layouts.

Jan 1, 2008

By F. Dinter, S. A. C. Hockaday, Q. G. Reynolds

The thermal decomposition of carbonate minerals as pre-treatment before smelting reduces the energy requirement for smelting. It can also make the combustion of fossil fuels for heating unnecassary. Thermal decomposition may become important in reducing greenhouse gas emissions when producing ferromanganese alloys while simultaneously reducing electrical energy demand during smelting. A kinetic reaction rate model for the thermal decomposition of manganese ores is presented, based on published reaction rate kinetics for the decomposition of manganese oxides and calcium carbonate. The model was validated against thermogravimetric data for two carbonaceous manganese ore samples and one ferruginous manganese ore sample. The reaction rate model shows that carbonate minerals in the manganese ores are decomposed at temperatures above 900 °C while pyrolusite is decomposed at temperatures from 450 °C to 500 °C. Mn2O3 decomposes rapidly at 550 °C. Braunite decomposition at temperatures below 1000 °C was negligible. The presence of organic carbon in the samples led to further reduction of the samples during thermal treatment.

Aug 3, 2023

By G. A. Georgalli

A control philosophy to be applied by Lonmin to maintain constant electrode immersion in their no. 1 circular smelting furnace is put forward. This control philosophy is facilitated though a combination of thermodynamic models used to predict the slag composition and empirical correlations to estimate the furnace geometric factor as well as the slag conductivity. The model can determine the operating resistance set point required in order to maintain a desired electrode immersion as a function of the feeds to the furnace, slag level and temperature. If modifying the resistance set point cannot maintain the desired immersion without moving out of the furnace P-V-I operating envelope, the model can be used to determine the amount of slag modifiers (silica or lime) required to shift the slag chemistry back into a region where the immersion can be controlled though resistance set point manipulation.

Jan 1, 2008

By G-L. Wu, S-W. Wu

"The hot deformation behaviour of Nb-Ti microalloyed high-strength steel was investigated. Hot compression tests were conducted in the temperature range 900 to 1100°C under strain rates of 0.1, 1, and 5 s-1. Dynamic recrystallization (DRX) occurs as the main flow softening mechanism at high temperature and low strain rate. The hot deformation activation energy was calculated to be about 404 699 J/mol. The constitutive equation was developed to describe the relationship between peak stress, strain rate, and deformation temperature. The characteristics of DRX at different deformation conditions were extracted from the stressstrain curves using the work hardening parameter. The Cingara-McQueen equation was developed to predict the flow curves up to the peak strain. The processing maps were obtained on the basis of a dynamic materials model. The results predict an instability region in the temperature range 1010 to 1100°C when the strain rate exceeds 0.78 s-1. IntroductionThe 700 MPa grade HSLA steel is widely used in engineering machinery, automotive beams, carriages, and axle tubes, etc. (Pan et al., 2017 ). Generally, such grades contain a moderately high amount of Mn (approx. 1.4% and above), and microalloying elements like Nb, Ti, V, and Mo to impart the desired strength and toughness through solid-solution strengthening, precipitation hardening, and grain refinement dislocation strengthening (Chen and Yu, 2012; Opiela, 2014). However, the production costs can be greatly reduced by replacing part of the Nb, V, or Mo with inexpensive Ti and adopting the compact strip production CSP process (Opiela, 2014; Chen et al., 2015). Furthermore, the microalloying technology coupled with new-generation thermomechanical control processing (NG-TMCP) has proved efficient for achieving the proper balance between strength, toughness, ductility, and formability by means of a suitable combination of chemical composition and thermomechanical treatment parameters (Shukla et al., 2012; Wu, Zhou, and Liu, 2017).In hot forming processes, the complex microstructural evolutions are often induced by multiplicative hot deformation mechanisms, such as work hardening (WH), dynamic recovery (DRV), and dynamic recrystallization (DRX) (Zhang et al., 2014; Liang et al., 2015). Dynamic softening behaviour during hot processing has generated considerable interest because component properties are influenced significantly by its corresponding microstructural evolution (Wu et al., 2010). During deformation in the DRX process, deformed grains are replaced with substructures and newly formed fine and uniformly distributed grains. This occurs only when a critical strain for the onset of DRX is reached, and at the same time, the minimum rate of energy dissipating is reached (Ferdowsi et al., 2014). DRV occurs at a high strain rate and low temperature, reducing the stored energy greatly and making DRX difficult (Liang et al., 2015). The microstructural changes during DRX are sensitive to the processing parameters, such as strain rate, deformation temperature, and strain (Zhang et al., 2014; Ferdowsi et al., 2014). Therefore, in order to optimize the hot processing parameters, it is important to understand the behaviour of hot deformation visà- vis control of microstructural evolution."

May 1, 2019

By R. L. Machunda, A. M. Rugaika, D. D. Mdachi

Sedimentary and igneous rocks are the two primary sources of phosphate that are mined and beneficiated to fertilizer. During the beneficiation process, phosphate is lost into the tailings. We investigated phosphate concentrations in tailings dumps at Minjingu mine, Tanzania using energy-dispersive X-ray fluorescence spectrometry to quantify the chemical compositions. The phosphate content in the tailings varied from 12.91% phosphorus pentoxide (P2O5) in Tailings 2 to 19.61% in Tailings Dump 1. The naturally occurring phosphate concentration in rocks ranges from 3% to 35%, and phosphate tailings from various locations with P2O5 concentrations as low as 6.46-12.65% have been beneficiated to commercial fertilizer. Our investigation revealed that phosphate concentrations in Minjingu tailings may be sufficient to be recovered for commercial applications. Suitable recovery methods are discussed, and we recommend that beneficiation should be performed to minimize the loss of phosphate into tailings. Further research is needed to identify the optimal beneficiation methodology.

Aug 8, 2024

By J. Danoczi

South Africa is running out of fresh water and is looking at ways to improve water usage. This report addresses how a diamond mine in Gauteng has improved the utilization of its water resources. In the past, water from the local river was deemed the most suitable to use in the grease recovery plant but subsequent tests on the water from the slimes dam have shows that this water source is in fact more suitable for diamond recovery. Utilizing the slimes dam water provides a more stable water source than the local river while also reducing the impact of the mine on the water resources in the area.

Jan 1, 2008

By R. D. Hancock

The complex responsible for the poisoning of anion-exchange resins is identified as the anionic cobaltic penta¬cyanide mono aquo species. It is shown that, at high concentration, this species polymerizes in solutions of pH less than 9. A mechanism for poisoning is presented that involves adsorption of anionic cobalt cyanide by a normal ion-exchange process, followed by polymerization within the resin matrix to form complexes that are too large to diffuse readily through the resin pores. The effects of resin structure and functionality on the extent of cobalt poisoning are examined, and the effect of cobalt poisoning on the kinetics and equilibrium loading of uranium is discussed.

Jan 1, 1979

By H. Zhong, S. Wang, Q. Sun

The flotation performance of 2-(benzylthio)-acetohydroxamic acid (BTHA) to diaspore was first evaluated by micro-flotation tests. The adsorption mechanism was further investigated through adsorption experiments, molecular dynamics simulation, zeta potential and X-ray photoelectron spectroscopy (XPS). The results demonstrated that BTHA had a stronger ability to collect diaspore in comparison with another diaspore collector, benzohydroxamic acid (BHA), especially under the condition of weak alkalinity, the flotation recovery can reach 90%. The more negative interaction energy (ΔE) between BTHA and diaspore from molecular dynamics simulation results revealed that BTHA had an easier adsorption ablity onto diaspore than BHA, which matched with adsorption results. The zeta potential and XPS revealed that Al atoms might bond with -C(=O)NHOH by formation of Al-O bonds. Keywords: Diaspore, flotation; adsorption; 2-(benzylthio)-acetohydroxamic acid

Jan 1, 2020

By C. D. Winkler

Vanadium-based sulphuric acid catalyst has been utilized to oxidize SO2 to SO3 since the early 1900s. This versatile product displaced the expensive and easily poisoned platinum-based catalyst in nearly all applications by the 1930s. MECS has been manufacturing the vanadium-based catalyst since 1925 and today is the leading supplier in the world of sulphuric acid catalysts in a variety of forms. Currently, MECS has worldwide customer/technical support for the catalyst as well as a dedicated catalyst manufacturing plant in Martinez, California. MECS also has a strong technical and research and development programme dedicated to creating new and improved products and services. This paper will describe some of the technical details of vanadium-based sulphuric acid catalysts as well as offering a unique look into how caesium-promoted MECS catalysts can be used in single and double absorption acid plants, and off-gas plants running on irregular gas feeds, to reduce emissions and preheater run times. An update on MECS technical services extended for use in characterizing converter performance is also presented.

Jan 1, 2009

By E. Van Der Lingen

Within the context of the overall gold market industrial demand plays an important role. Industrial demand for gold was 430 tonnes in 2008, approximately 12% of total end-user consumption. The dominant consuming industry in this market for gold remains the electronics sector, consuming an estimated 300 tonnes, primarily through the use of gold bonding wire for computer chips and plated contacts and connectors. Substantial demand also derives from dental applications, with other smaller industrial markets and decorative uses of the metal (non-jewellery) constituting the balance. In each market gold faces tough competition from alternative lower cost materials, such as silver and copper (electronics) and ceramics (dental). As well as the obvious benefits to the gold market resulting from this constant physical demand, there are an umber of additional positive factors concerning the use of gold in industrial applications: ?Price inelasticity: demand for gold from the major consuming industries has so far proven to be relatively robust in the face of significant increases in gold price. ??Stickiness?: the gold consumed by industrial uses tends not to return easily to the market (i.e. the demand is ?sticky?) because it is highly dispersed. ?Image: the beneficial environmental and medical applications of gold (e.g. gold used in the treatment of prostate cancer and in purification of contaminated water) are helpful to the positive image of gold. ?Added-value: new industrial uses for gold can create substantial added value in the supply chain, particularly in gold producing countries.

Jan 1, 2009

By H. Bhikha

The minerals industry is committed to the principles of sustain-ability. Reducing water consumption is a priority area, especially for regions of water scarcity. This paper presents a systemic optimization of the water balance of the Skorpion Zinc refinery with the aim of reducing water consumption. An Aspen Plus simulation of the process is used. The validity of the simulation is tested by measuring key output variables and comparing results to plant data. A number of water minimization scenarios are investigated, Including unit operation and circuit configuration changes. The scenarios leading to the largest reduction in water consumption are through the full recycle of treated effluent water, which results in water savings of up to 19%. Reducing process water and/or recycling of untreated water is prohibited by the build-up of trace elements, which affect product purity. The Skorpion process already features a highly optimized water balance, with unit operational changes merely resulting in a shift in the water balance. Consequently, the largest area for improvement is through the re-use of effluent water. Keywords Skorpion zinc water usage, process optimization, sustainability.

Jan 1, 2011

By V. Léveillé

As new legislation drives metallurgical plants to lower SO2 emissions, plant managers face the challenge of keeping their costs under control. The Cansolv® SO2 Scrubbing System has been broadly adopted in the non-ferrous industry as a cost-effective solution for smelter operators to meet the new SO2 emissions targets. The Cansolv® SO2 Scrubbing System is an a mine-based regenerable process that selectively absorbs SO2 from a variety of gases, including dilute smelter gases, such as furnace and converter gases. The system produces a pure, water-saturated SO2 by-product stream, which can then be directed to the front end of a sulphuric acid plant for conversion to sulphuric acid. When deployed in a smelter complex, the Cansolv® SO2 Scrubbing System may also be used to process acid plant tail gas, allowing single absorption sulphuric acid plants to achieve emissions an order of magnitude lower than that of a double absorption acid plant with a lower capital investment. Depending on inlet gas temperature, SO2 emissions in the treated gas can be controlled to as low as 55mg/Nm3. This paper will describe some of the applications where customers have or are planning to use the Cansolv® SO2 Scrubbing System, as well as which features and cost advantages for the treatment of smelter gases were important in the technology choice.

Jan 1, 2009

By H. B. Prinsloo

Change management and training initiatives in remote rural settings in Africa are generally difficult to implement successfully due to factors such as varying levels of education, multiple nationalities and languages as well as cultures in one workplace. The challenge has always been the ability to implement change management and training initiatives that will have an impact despite these differences. Essentially this requires that the change and training interventions employed are applicable and should work well with a wide range of individuals sitting in one room ? in practice this can vary from semi-literate workers to engineers with PhDs. In this paper we will share the theory behind behaviour-based change management and training and present a case study that reviews an actual supply chain improvement and sustainability implementation at a Zambian copper mine. The case study explains the results achieved as well as the interventions employed to achieve these results in a multidimensional organizational environment. This paper is relevant to delegates who are faced with implementing changes or training in a similar mining environment. Keywords change management, behaviour-based training, learning style, P2P process.

Oct 1, 2013

By Q. Liu, S. Liu, Y. Cui

To reduce the frequency of mining incidents and improve safety and production efficiency, it is important to develop technology for the autonomous positioning and navigation of mining equipment, without the assistance of satellite navigation signals. In this study we review the current technological environment for positioning and navigation underground and present several integrated navigation strategies. Existing underground positioning and navigation technology is described, and the performances of different methods based on this technology analysed and compared. The combination types and positioning effects of underground positioning and navigation strategies are discussed. Recent research directions for filtering methods and positioning estimation algorithms for underground positioning and navigation are reviewed. Finally, we summarize the future direction of underground positioning and navigation technology and related algorithms.

Jun 1, 2021

By M. Rudolph, A. van Hall, G. Öktem, S. G. Özkan, A. Hassanzadeh

Despite the four-decade study on ultrasound’s (US) impact on mineral’s floatabilities, there is still not clarity regarding its role in mineral surface wettability. For this purpose, the present investigation endeavours ……the hydrophobicity and floatability characteristics of a chalcopyrite-pyrite-quartz (Cp- Py-Qtz) system in the presence and absence of an ultrasonic pre-treatment. The ultrasonic process was carried out by a sonopuls at a constant frequency of 20 kHz with an adjustable power level from 30 to 200 W. Initially, the impact of sonication time (15, 30, 45, 60 and 90 s as well as 10, 20 and 30 min) and power magnitude (30, 60, 90, 120 and 180 W) were evaluated while the dissolved oxygen, temperature, conductivity and pH were also monitored. Collector-less micro-flotation tests were carried out on the non-pre-treated and the US pre-treated samples at 60 W and 15 s. The samples’ hydrophobicities were determined by the drop shape analysis approach. The dissolved-oxygen level was varied using a mini bench pressurised water reactor to study the effect of O2(aq) concentration on the chalcopyrite and pyrite wettability characteristics. The results showed that the minerals’ hydrophilicities were relatively more sensitive to the sonication’s time than its power that resulted in reducing all three minerals’ hydrophobicities. In addition, it was found that the dissolved-oxygen content and creation of sub-micron sized bubbles led to an improvement on chalcopyrite and pyrite hydrophobicities. Finally, we proved that the Cp’s floatability increased and Qtz’s recovery reduced while being subjected to the ultrasonic irradiation (15 s at 60 W); however, Py’s recovery remained constant. This conclusion confirmed the possibility of a selective separation in ultrasound-assisted copper ore flotation. We recommend that further advanced investigations be conducted, using an X-ray photoelectron spectroscopy (XPS) and atomic force microscopy (AFM) to thoroughly understand the surface modifications induced by the ultrasonication

Jan 1, 2020

By P. Gonzalez

Minera La Parreña, S.A. de C.V., Milpillas operation is an underground mine designed to process 8 352 tons of ore per day for the recovery of copper through crushing, heap leaching, solvent extraction and electrowinning facilities. In order to optimize copper recovery during leaching, the ore is crushed to 13 mm and subjected to primary sampling every 15 minutes for metallurgical accounting. At the same particle size, primary sample goes to secondary sampling and then, the secondary sample is crushed to 2 mm before tertiary sampling. The tertiary sample is sent to laboratory where a final sample is obtained and pulverized to 106 microns for copper assay. This paper shows a review of sampling strategy focused on minimizing or eliminating sampling errors and an experiment designed to determine copper head grade profile as well as the best sampling frequency.

Jan 1, 2009

By Stephen Yirenkyi

The mining industry remains the backbone of many economies in the developing world. Its resurgence in Ghana since 1989 was driven by the global paradigm which emphasizes private sector-led development as the engine of economic growth in developing countries. The historical importance of mining in the economic development of Ghana is evident in the country?s colonial name, Gold Coast (Akabzaa T. and Darimani A., 2001). Ghana earned $2.5 billion from mineral exports in 2007. 20,000 people are employed in large-scale mining whilst 500,000 are employed in the small-scale sector. Mining contributes about 7% of Ghana?s total corporate tax earnings, 41% of total exports, 12% of revenue collected by the Internal Revenue Service and 5% of Gross Domestic Product (Ghana Chamber of Mines, 2008). Gold dominates the mining sector and the country is Africa?s second largest gold producer after South Africa. Surface Mining, which refers to a method of extracting minerals from the earth by their removal from an open pit or borrows, requires a large tract of land for its operations (Wikipedia, 2008). There is therefore a continuous divergence of interest between land required for surface mining and other land uses such as farming and housing, among others. In recent years, surface mining has been promoted in many mining countries because of the following reasons: ?Cost considerations compared to underground mining; ?Safety considerations, compared to underground mining; ?Low grade ore which requires processing huge quantities; ?Location of the ore bodies; and ?Competition among gold producing countries for investors. This paper looks at the socio-economic impacts and challenges of surface mining by using Gold Fields Ghana Ltd. Tarkwa, Ghana as a case study. The company has a concession of about 208 sq km located in the heart of the Wassa communities in the Western Region of Ghana and undertakes surface mining like most of the other mining companies in the country. Gold Fields, Tarkwa mine produces 700,000 ounces of gold a year with the potential of increasing this output to 800,000 ounces after its current expansion programme. Some of the effects of surface mining identified were: 1. Relocation/Resettlement of host communities and its negative effects; 2. Disturbance to Flora and Fauna; 3. Disturbance to Sacred Places; 4. Land Degradation; 5. Noise and Air Pollution; and 6. Water Pollution. This paper sought to investigate the measures put in place by the government and the Gold Fields Ghana Ltd. to mitigate the above effects in order to ensure peaceful coexistence between the mining company and its host communities. It concludes that most mining companies presume the provision of socio-economic development in mining communities will lead to the company securing a social license to operate. This however is not true but rather effective community relations combined with socio-economic development. According to Gold Fields Ghana Ltds. model, this involves continuous community engagement, conflict resolution and comprehensive environmental monitoring programme which will all lead to effective community relations. The strategies to ensure socio-economic development involves community development programme, livelihood restoration programme and community training and employment. All these will then lead to sustainable development which will ensure the company?s social license to operate. Gold Fields? model is in line with the principles of responsible mining. With this model, the community feels they are part of the company and the social license of the company is guaranteed. Gold Fields? model, which has been tried and tested for the past five years, could serve as a template with suitable modification for local conditions for other mining countries where surface mines operate.

Jan 1, 2008

By T. Feroze, B. Genc

"The ventilation of underground coal mines plays an important role in minimizing the risk of methane and coal dust explosions. The ability of ventilation, with the use of line brattices (LBs), to remove methane and coal dust in empty headings is dependent on the amount of air leaving the LB and entering the heading. The quantity of this air depends on the associated system variables, namely heading dimensions, settings of the LB, and velocity of air in the last through road (LTR). However, the exact effect of these system variables on the flow rate at the exit of the LB in an empty heading is not known. The installation of LBs in South African coal mines is generally carried out based on experience. This can result in overor under-ventilation and may increase the cost of providing ventilation or cause accidents, respectively. In this paper, using computational fluid dynamics (CFD), the air flow rate at the exit of the LB in an empty heading was estimated using full-scale three-dimensional models. The CFD model used was validated using experimental results Firstly, the settings of these three system variables were varied, the flow rates at the exit of the LB were measured, and finally the results were used to calculate the effect of each system variable. The outcome is a mathematical formula that can be used to estimate air flow rate at the exit of the LB in empty headings for any practical scenario.This paper will help the coal mining sector in South Africa by providing estimation models based on scientific reasoning for the installation of LBs, and will also serve academia as part of the curriculum towards educating future mining engineers."

Jan 1, 2016

One of the most critical and complicated steps in mine design is a suitable mining method selection based upon geological, geotechnical, geographical and economical parameters. Since there are many factors involved in mining method selection, the decision-making process is very difficult. In this paper, the Analytical Hierarchy Process, with 13 criteria, is used to develop a suitable mining method for the Golbini No. 8 deposit in Jajarm (Iran). Six alternatives (conventional cut and fill, mechanized cut and fill, shrinkage stoping, sublevel stoping, bench mining, and stull stoping) are evaluated. The studies show that the suitable mining method for this deposit in the present situation is the conventional cut and fill method.

Jan 1, 2008