Search Documents

By K. E. Mantell

1. TRACKLESS MINING AT OAMITES by K. E. MANTELL Oamites Mine, brought into production in late 1971, is located 50 km south of Windhoek, South West Africa, on the northern boundary of and just outside the Rehoboth Gebied. Oamites was known as a possible mining proposition at the turn of the century when Hanseatische Minen Gesellschaft was adit mining on the adjacent farm Kamzwas. Rand Mines Limited carried out a small amount of prospecting in the early 1960s, Falconbridge Explorations Limited later taking over the prospect. Approximately 4600 m of diamond drilling was carried out between 1965 and 1967.

By W. Wilmans

Electrokinetic dewatering of kimberlite slime under constant direct curents of 0,5 to 2 A and dewatering under constant applied potentia Is of 16,5 to 46,5 V are considered. The combined efects of electrophoresis and the addition of 8,3 x 10-3 M Mg2+ ions on the one hand, and 1 to 10 p.p.m. of the anionic polyacrylamide flocculant Praestol 2935 on the other, were investigated in a 3-litre Perspex electrophoretic cel. .The electro-osmotic dewatering experiments were conducted in a 3-litre Perspex electro-osmotic cel at various electrode spacings, as well as with a moving anode (top electrode). During electrophoretic dewatering, the zeta potential of the kimberlite particles did not change significantly, whereas the pH and temperature showed marked increases with time. The addition of Praestol 2935 enhanced the setling of the sludge bed owing to the additional effect of flocculation. The addition of electrolyte Mg (CIO4)2 retarded the separation process, partly as a result of gel formation in the slurry. During the electro-osmotic experiments, the rate of dewatering was found to be approximately proportional to the applied constant direct current, and to be independent of the electrode spacing. In general, electro-osmotic dewatering seemed to be more energy-efficient than electrophoretic dewatering.

Jan 1, 1987

Infacon 74 Members are reminded of the International Ferro-Alloys Congress that is to take place in Johannesburg between 22nd April and 1st May, 1974. The Congress is being held jointly by the National Institute for Metallurgy, the Ferro Alloy Producers' Association of South Africa, and the South African Institute of Mining and Metallurgy. Correspondence and enquiries should be addressed to The Secretary, Organizing Committee, INFACON 74, Private Bag 7, Auckland Park 2006. The gold deposits of the farms Lisbon and Berlyn in the Eastern Transvaal by v. c. H. R. BRERETON. Published in the Journal November 1973. AUTHOR'S CORRECTIONS The following amendments should be made.

Jan 2, 1974

1. Book reviews Geophysical and geochemical techniques for exploration of hydrocarbons and minerals, edited by M. Sittig. (Reviewer: J. Keenan) Separation procedures in inorganic analysis. A practical handbook, by Roland S. Young. Charles Griffin, 1980. £23.00. (Reviewer: R. Murray-Smith) 2. Historical reprints Theinin~rs dictionary, by William Hooson. £14. Discovery of subterraneal treasure, by Gabriel Plattes. £12. Fodinae Regales (The Mines Royal), by Sir John Pettus. 3. De Beers' booklets Amborite - a remarkable new cutting material, by De Beers Industrial Diamond Division (P.O. Box 916, Johannesburg 2000). Booklet, 14 pp., free of charge. Natural and synthetic micron powders, by De Becrs Industrial Diamond Division (P.O. Box 916, Johannesburg 2000). Leaflet, 5 pp., free of charge. 4. New books Nickel in the environment, edited by J. O. Nriagu. New York, Wiley, 1980.928 pp. $65. Underwater minerals, by D. S. Cronan. London, Academic Press, 1980. 364 pp. $57.50. Data conversion integrated circuits, edited by D. Dooley. New York, Wiley, 1980.298 pp. $26.95 (cloth), $17.50 (paper). 5. NIM reports Report 2057 A mineralogical study of the Rooibokkop- Boschhoek copper deposit in the Marble Hall area. Report 2069 A utomatic setting of the distance between sample and detector in gamma-ray spectroscopy. Report 2070 The prereduction of chromites from the UG-2 Reef. Report 2075 The optimization of some of the conditions for analysis by spark-source mass spectrometry. Report 2082 A survey of the literature on gravity separation.

Jan 1, 1981

By S. T. L. Harrison, M. Smart, C. J. Edward

Biooxidation, a biohydrometallurgical process, utilizes a mixed microbial consortium to mediate the dissolution of refractory gold-bearing ores to enhance gold recovery during cyanidation. Recognition of water as a critical resource has prompted improved water management strategies within mining and minerals processing. Bioremediated wastewater from the cyanidation tailings provides a potential water source to supplement the water required for the biooxidation circuit, reducing freshwater extraction. Gold biomining operations have typically been reluctant to recycle this wastewater due to the potential inhibitory effects of cyanide and thiocyanate (SCN-) on the microbial population. Historical process upsets suggest that the microorganisms are sensitive to SCN- concentrations as low as 1 mg/L. However, effective bioremediation processes resulting in effluents with low or negligible SCN- concentrations may allow gold biomining plants the opportunity to recycle available water. Microbial activity as well as alteration in community structure were monitored as a function of increasing SCN- concentration over the range of 0 mg/L to 5 mg/L to investigate the response of the biooxidation community to potential SCN- spikes resulting from upsets in the remediation process. Appropriate microbial growth and ferrous iron oxidation activity with a nominal shift in community structure were observed at SCN- concentrations up to 1 mg/L. Thiocyanate concentrations above 1 mg/L resulted in the complete inhibition of ferrous iron oxidation activity. This was attributed to Leptospirillum ferriphilum’s sensitivity to SCN-. Exposure to a SCN- concentration of 5 mg/L resulted in a lower cell concentration and a significant increase in growth lag time, and the absence of L. ferriphilum from the microbial population. At. caldus and Ap. cupricumulans were still present at 5 mg/L SCN-, although Ap. cupricumulans was unable to oxidise ferrous iron at this SCN- concentration. It was concluded that recycling bioremediated cyanidation tailings wastewater within the biooxidation circuit is feasible; however, to retain process performance, SCN- concentrations should not exceed 1 mg/L. Keywords: Biooxidation, thiocyanate, water recycling, community structure

Jan 1, 2020

By O. A. Olaseinde

The 2101 lean duplex stainless steel has wide potential application in storage, heat exchangers, and in the oil and gas industries. This work investigates the electrochemical behaviour of 2101 duplex stainless steel with an addition of 0.15 wt% ruthenium, using potentiodynamic techniques in 1M H2SO4 at 25º, 40º, 60º, and 80ºC. The microstructures of samples were characterized using optical metallography and scanning electron microscopy. The results showed that the ruthenium addition moved the corrosion potential of alloy 2101 to a more positive potential. All samples containing ruthenium displayed longer passive regions at 25°C and 80°C compared to those without ruthenium. Alloys without ruthenium had higher critical current density (icrit) values when compared to the alloys with ruthenium. Ruthenium additions decreased the passive current densities and inhibited anodic dissolution. At room temperature the corrosion rate of alloys with ruthenium was lower than these without ruthenium.

Jan 1, 2012

Book review Pearson, J. S. Ocean floor mining. Park Ridge (New Jersey), Noyes Data Corporation, 1975. 201 pp. NIM reports Report no. 308 A mineralogical study of gold particles in pulp residues from the Bracken Gold Mine. (7th Mar.,1968. Re-issued Oct. 1975.) Report no. 377 Examination of pulp samples, treated with cyanide, for coated gold.(7th Aug., 1968. Reissued Oct.1975.) Report no. 385 The determination of the nature of coatings on gold particles. (2nd Aug., 1968. Reissued Oct. 1975.) Report no. 452 The Purlex Process - a description of the pilot plant leading to the use of the process in South Africa. (13th Jan., 1969. Re-issued Oct. 1975.) Report no. 482 Review of work on the treatment of pegmatites. (9th Apr., 1969. Reissued Sep. 1975.) Report no. 1443 Gravity concentration tests on four samples from Tantalite Valley,S. W.A. (5th Jul., 1972. Re-issued Sep. 1975.) Report no. 1489 The breakage of S oderberg electrodes. (10th Nov., 1972. Re-issued Nov. 1975.) Report no. 1545 A mineralogical investigation of leach residues from the Blyvooruitzicht Gold Mine. (22nd May, 1973. Re-issued Nov. 1975.) Report no. 1583 Preliminary tests on winnowing for the recovery of mica. (12th Nov., 1973. Re-issued Sep. 1975.) Report no. 1652 The identification of diamonds from Premier, Finsch, and Jagersfontein Mines by statistical analysis of data obtained from instrumental neutron-activation analysis. Report no. 1723 The determination of zirconium and aluminium in zirconiumaluminium alloys. Report no. 1739 The determination of trace amounts of noble metals in sulphate media. Report no. 1771 The determination of silver, selenium, tellurium, antimony, tin, lead, and arsenic in anode sludges. Report no. 1772 A study of copper recovery by lime roasting and leaching. Corrigendum The Special Issue of Volume 76 of the Journal ('Recent Advances in Mineral Dressing, October 1975) should be corrected as follows. The South African Institute Of Mining And Metallurgy - Information On Membershlp The Institute was founded in 1894 as the Chemical and Metallurgical Society of South Africa. In 1904 it was reconstituted as the Chemical, Metallurgical and Mining Society of South Africa and in 1956 it became the South African Institute of Mining and Metallurgy. Die Suid-Afrikaanse Instituut vir Mynbou en Metallurgie - Inligting Oor Lidmaatskap Die Instituut is in 1894 gestig as die Chemiese en MIetallurgiese Vereniging van ::!nid-Afrika. In 190-1is dit omvorm tot die Chemiese Metallurgiese en Mynbouvereniging van Sllid-Afrika en in 1956 het dit die Suid-Afrikaanse Instituut vir Mynbou en l\Ietallurgie geword.

Jan 2, 1976

By J .. F. Brownrigg

In the mining method used at O'Okiep Copper Company (OCC), vertical crater retreat, the prime requirement for the fill is that it should be sufficiently strong to be free-standing to a height of 150 m. Other requirements are minimal decant and drainage water, and high pulp density to allow large tonnages to be placed quickly and alleviate transport problems. The excessively high cost of cement precluded the use of a cement-based fill, and after three years of extensive investigations a backfill based on the smelter slag was produced. Currently a fill with a uniaxial compressive strength of greater than 1 000 kPa after one month is being produced. This is in excess of the design specification of 850 kPa after 2 - 3 months. The research and development which went into the slagfill is briefly covered; the production of the fill from the various raw materials is described; and the design and control systems of the backfill plant, the reticulation system and its monitoring are examined. Finally, the implications of this high- quality fill for the mining programme are assessed.

Jan 1, 1988

By S. J. Moema, M. G. Maruma, L. A. Mampuru, M. E. Maja

"The most commonly used high-chromium white cast iron (HCWCI) is the hypoeutectic white cast iron that contains 2–3.5 wt.% C and 10–30% Cr. This type of material relies on hard, brittle M7C3 carbides to impart good wear resistance. Due to its good wear resistance, this material has found application in the mining industry and cement industry. However, it has low fracture strength and this challenge led to research aimed at refining the microstructure. This was done by the addition of niobium in the range between 0.1 and 0.6 wt.%. In the as-cast condition, the addition of niobium was found to increase the fracture strength due to the finer eutectic microstructure. The hardness was also found to have increased slightly compared to the reference alloy with no niobium additions. Low fracture strength after heat treatment was observed in the Nb-added HCWCI, which is believed to have been caused by the precipitation of secondary carbides and the transformation of the matrix from austenite to martensitic. IntroductionFor the past few years Mintek has been involved in a project in which a number of alloys have been identified for grinding media applications. The high-chromium white cast iron (HCWCI) alloys were among the alloys researched for this application. The knowledge acquired from the grinding ball media research has now been extended to mill liners, which have traditionally been made of manganese-, chromium- and chrome-molybdenum steels. The replacement of worn mill liners costs the mining industry a significant amount of money and this has led to a need for continuous research to prolong the life of the liners. During milling operations, liner wear has an adverse effect on the capacity of the mill, the energy efficiency and milling efficiency and finally leads to relining, to replace worn liners."

Jan 1, 2016

By M. R. Khalesi

A method is proposed to estimate the gold content of the ore in the size intervals during size reduction. The method uses the population balance model to trace the gold deportment through the size fractions and monitor the generation of liberated gold grains during the size reduction. The model is calibrated using batch grinding test results of a gold ore. Preliminary results show that the model can be calibrated with a minimum of parameters compared to conventional grinding-liberation models. Keywords: simulation, liberation, gold, exposure, grinding

Jan 1, 2009

Book Review Gold Metallurgy in South Africa, edited by R. J. Adamson and published by the Chamber of Mines of South Africa, Johannesburg, 1972. The metallurgical processes used for the recovery of gold from Witwatersrand ores were first described in A Text Book of Rand Metallurgical Practice, published in 1912 and subsequently revised in 1926. This was followed by Gold M etall1trgy on the Witwatersrand by A. King in 1949. New Publications Elements of Practical Coalmining, S. M. Cassidy (editor), New York, Society of Mining Engineers of AIME, 1973, $16.50. Future Enerey Outlook, J. A. Pederson (editor), Colorado School of Mines Quarterly, vol. 68, no. 2, April 1973, $6.00. Guide To The Preparation Of Papers For Publication In The Journal Of The South African Institute Of Mining And Metallurgy The following notes have been compiled to assist authors in the preparation of papers for presentation to the Institute and for publication in the .Journal.

By I. Y. Motovilov, S. A. Telkov, M. B. Barmenshinova, Z. S. Abisheva

As a rule, removing waste rock at the beginning of the process improves the conditions for the flotation of minerals, and also reduces the operating costs of crushing, grinding and flotation. Lead-zinc ores in the Shalkiya deposit of the Republic of Kazakhstan are classified as difficult for enrichment, but taking into account their significant reserves, they are one of the main potential ores for the production of lead and zinc. Under industrial conditions, for processing ores of the Shalkiya deposit, a selective flotation concentration scheme with the production of lead and zinc concentrates is recommended. However, according to the recommended scheme, it is not possible to obtain high-quality concentrates of lead and zinc, with high metal recovery. The paper presents the results of studies of preliminary gravitational enrichment of lead-zinc ore in the Shalkiya deposit. Based on the fractional analysis for the particle size range of -40+8 mm, Henri- Reingard enrichment curves were constructed, separation density (2730 kg /m3) was established to isolate the light fraction with the lowest possible lead and zinc content, and gravity enrichment indices (0.7-0.71) were determined. It was found out that when using gravitational enrichment of the original large-sized ore in the Shalkiya deposit, tails are released at the beginning of the technological process with a yield of up to 20% with the extraction of silica up to 30%, calcite up to 11% and carbonaceous matter up to 12%. As a result of the studies, it was found that the beneficiation of crushed lump ore could be conducted in heavy suspensions. One of the positive aspects of the use of gravitational enrichment is the reduction of energy costs for grinding the heavy fraction, which was experimentally proved in this article. Keywords: Lead-zinc ores, Shalkiya deposit, fractional analysis, gravitational enrichment, floating fraction, sunken fraction, separation density

Jan 1, 2020

Minutes of the Annual General Meeting Held at Harmony Country Club on Wednesday, 2nd August, 1978, at 7.30 p.m. Mr A. N. Shand (Chairman of the O.F.S. and Klerksdorp Branch) was in the Chair. Also present were:.... Induction of Chairman Mr A. N. Shand introduced Mr H. M. W. Eschenburg by briefly outlining his past career and achievements, and, in calling upon him to take the Chair, wished him a very successful year of office..... Address by the President of the S.A.I.M.M. The Chairman introduced Mr Von Wielligh by outlining his career and achievements. After completing his education, he joined J.C.I. in 1936 as a sampler, and from that time served the company in many capacities, culminating with his appointment to the Board in 1974.....

Jan 1, 1979

By D. L. B. Pollnow

Tinplate, and electrolytic tinning at the Iscor works, Vanderbijlpark by D. L. B. POLLNOW, B.Sc. (Chem.), M.Sc. (Met.), D.Se. (France) The paper first describes tinplate as a product, dealing with its structure and its advantages to the packaging industry. It then describes Iscor's electrolytic tinning line, which is one of the largest Halogen units in the world. Details are given of the process and of the equipment used.

Jan 1, 1977

In China, thin coal seams are rich in resources but are technically challenging. The mineable reserves in these seams account for 20.4% of the total coal resources, while the current production accounts for only 10.4% of the total annual production. Characteristics such as narrow mining space, low level of mechanization, poor working environment, and high cost of mining, restrict the development of mining safety and efficiency. Recently, fully mechanized mining technology has developed rapidly for thin coal seams, the level of yield and efficiency has reached or exceeded the international standard, and some state-owned key coal mines are considering automation of their mining process. In thin coal seams with hard stone bands that contain concentrations of pyrite, a specialized software, LS-DYNA, is used to calculate the rational blasting parameters that are used in the deep-hole pre-splitting blasting. Using this method the hard stone bands are fractured effectively, and hence increasing the coal productivity. In addition, mining advance rate were increased by enhancing the level of fully mechanized equipment and safety improved by increasing gas drainage from the gas outburst prone seam located some 7 m below the coal horizon. At present, thin coal seam mining technology faces many challenges, including the low level of equipment automation, the low advance rate in mixed coal-rock ground, and the large number of the mine personnel underground. By lowering the labour intensity and improving efficiency through automation and other measures, more efficient working faces can be implemented in thin coal seams.

Jan 1, 2012

This paper presents the development of a regrind facility design at BHP Billiton's Leinster Nickel Operations (LNO) in Western Australia. The recovery opportunity was identified from an analysis of plant operating data together with scanning electron microscope (SEM) measurements on relevant tailings streams from LNO. A laboratory procedure was developed to determine the potential recovery improvement of installing a regrind facility at LNO. The last step in formulating the process flow sheet and defining the process design criteria was to construct and operate a pilot plant, which incorporated four banks of flotation cells and an Xstrata M20 Isa Mill. Pilot plant on/off trials were used to define the expected metallurgical benefit. A prefeasibility engineering design and cost estimate was completed. Following a successful internal business evaluation, a feasibility study is currently underway.

Jan 1, 2007

By P. W. J. van Rensburg

COLLOQUIUM AND GENERAL MEETING A General Meeting and Colloquium on comminution was held on March 13th, 1974, at Kelvin House, Johannesburg. Mr P. W. J. van Rensburg (President) was in the chair. The Colloquium was attended by 140 delegates and was opened by the President at 9.15 a.m. MINUTES The minutes of the general meeting held on November 14th, 1973, as published in the December issue of the Journal, were confirmed.

Jan 5, 1974

By J. A. Tyser

The pumping of water from mines in the Central Witwatersrand by J. A. TYSER, Pr. Eng., B.Sc. (Min.) (Associate) This paper describes a system for the removal of underground water in the mines of the Central Witwatersrand, some of which are defunct. The water is pumped by a pump station on 24 level at E.R.P.M. to a surface lime plant and then to a surface treatment plant, where it is treated so that it meets the specification of the Department of Water Affairs relating to the deposition of water in public streams.

Jan 5, 1977

By X. J. Lyu, Q. Liu, M. J. Lian, X. Q. Cao, X. F. You, B. O. Erdenekhuyag, H. Y. Zang

The slag-tailings based artificial reef concrete (ARC) is made of CaO-CaSO4 activated granulated blast furnace slag (GBFS) as cementitious material and deslimed gold ore tailings as aggregate. In order to investigate the potential application of the material as ARC, the strength development, hydration characteristics and application performance were investigated under different preparation conditions. Results indicated that using seawater as the mixing water can effectively promote the hydration of slag and generate a large amount of hydration products such as ettringite, CSH gel, hydrotalcite and Friedel ’s salt in the early curing period and so render the material with good early compressive strength. Seawater curing can also accelerate the hydration reaction in the early stage of hydration. The hydration reaction of slag and the compressive strength of ARC can be effectively promoted by increasing the specific surface area of slag. The 28-day compressive strength of the slag-tailings based ARC prepared with 30-50% CaO-CaSO4 activated slag and 50-70% tailings can reach to 19.88-42.87 MPa. Also, the material has a low surface pH value, good resistance to chloride ion penetration, and sulfate corrosion. Keywords: Artificial reef concrete, granulated blast furnace slag, deslimed gold ore tailings, compressive strength, hydration characteristics

Jan 1, 2020

By S. O. Castro, R. E. González, L. E. Velasco, J. M. Van Sint, P. V. Lois

Abstract Several zones with expansive rocks were encountered during construction of two tunnels of the water conduction system for the Chacabuquito Hydropower Plant, located in the Aconcagua river valley of the Chilean Central Andes Mountains, at elevation 1.075 m a.s.l., and 65 km north-northeast of Santiago. The expansive behavior was associated to three different geological features. Firstly with the crossing of important north-south trending faults, with montmorillonitic and caolinitic fillings. Secondly to the presence of zones of rock mass showing a penetrative presence of clay minerals (montmorillonite, illite and caolinite) and penetrative thin veins of ceolites. And thirdly to the hydrothermal alteration of the rock and the consequent generation of clay minerals (predominantly montmorillonite, sericite and minor caolinite). The geological and mechanical characteristics of the expansive rock domains, as well as the field and laboratory reconnaissance and characterization program, are described in the paper together with the bases for design and the guidelines for construction and definitive tunnels support. Resúmè Pendant l’excavation des deux tunels du système d’adduction d’eau pour alimenter la centrale hidroélectrique Chacabuquito, plusieures zones de rochers expansifs ont été découvertes. Ces tunnels sont dans la vallée du fleuve Aconcagua de la Cordillère des Andes du Chili Central, à une altitude aproximée de 1.075m s.m.n. et à 65km vers le nord-nord-ouest de Santiago. Cette conduite expansive est associée à trois différentes caractéristiques géologiques du massif rocheux. Un premier lieu, à l’intersection de plusieures zones de failles, d’orientation nord-sud et subverticales, avec remplissage de rochers désintégrés, montmorillonite, caolinite et sérite. En seconde lieu, a la présence de zones de rochers expansifs, avec des nombreux minces veines de céolite-calcite et aussi des minéraux argileux (montmorillonite, illite et caolinite). Et, dans troisième lieu, dût à la présence de zones d’altération hidrothermale du massif rocheux et la conséquente génération de minéraux de remplacement argileux (surtout sérite, montmorillonite et en plus petit degré, caolinite). Les caractéristiques géologiques et géomécaniques des rochers expansifs, ainsi que la reconnaissance du terrain et les résultats du programme d’essais de caractérisation géomécanique du laboratoire sont décrits dans ce travail, ainsi que les bases de dessin et recommandations constructives pour placement du support définitifs pour ces tunnels Zusammenfassung Während der ausgrabung der zwei tunnels der wasserleitungssystem, um die Chacabuquito Wasserstromzentrale zu besorgen, wurden verschieden ausgedehnte gesteinadern gefunden Die beiden tunnels befinden sich im Aconcaguatal, wo der Aconcagua Fluss fliesst, auf einer Höhe von 1.075 m über dem Wasserspiegel und ca. 65 Km Nord-Nordest von Santiago entfernt, in mittleren Anden Cordillere (chilenische Gebirgskette). Drei verschiedene geologische merkmale dieser massiven gesteine können dieses ausgedehnte verhalten erklären. Erstens, hier befinden sich verschiedene und auch ganz wichtige

Jan 1, 2003