Search Documents

By L. Nahai

Iran's petroleum industry is nearly 50 years old and the oldest in the Near East. According to published figures, Iran ranks third in production and reserves in the Near East. These reserves (including probable reserves) are estimated at 35 billion barrels and constitute about 11 percent of the world's total. Iran is the sixth largest producer of crude petroleum in the world. The 1961 output of more than 430 million barrels was 5 percent of total world output for the year. In the same year, Iran ranked fourth among world petroleum exporters, providing 8.4 percent of total world exports.

Jan 1, 1963

By L. Nahai

Iran's petroleum industry is nearly 50 years old and the oldest in the Near East. According to published figures, Iran ranks third in production and reserves in the Near East. These reserves (including probable reserves) are estimated at 35 billion barrels and constitute about 11 percent of the world's total. Iran is the sixth largest producer of crude petroleum in the world. The 1961 output of more than 430 million barrels was 5 percent of total world out-put for the year. In the same year, Iran ranked fourth among world petroleum exporters, providing 8.4 percent of total world exports.

Jan 1, 1963

The Bureau of Mines annually publishes statistical data reflecting technological trends in the minerals industry (metals and nonmetals except fuels). This report outlines recent developments and trends and the technology outlook for mining practices and metallurgical processing based on a review of the minerals industry during the past 2 years. A historical statistical series which indicates trends in the minerals industry has been extended with 1970 data. In addition, data are given from a 5-year Bureau of Mines cyclic canvass of froth flotation plants. Data for 1970 are compared with those of 1960 and 1965.

Jan 1, 1972

By Frederick H. Raab

An electromagnetic (EM) system for the location of trapped mine workers at coal-mine (300 m) depths has been developed. The use of such a system in deep mines (1-km depth) requires transmission at extremely low frequencies (ELF) and a reduction in the effective noise level beyond that which can be obtained by acceptable Integration times. Automatic-noise-cancellation (ANC) techniques reduce the effective noise level by combining several received signals that contain correlated noise. Such signals can be obtained either from a remote magnetic antenna or a local electric antenna. During Phase III of this program, real ELF noise data were acquired and used to test the ANC algorithms developed during Phase II. The ELF noise data were obtained from analog recordings made by Develco under another Bureau-of-Mines contract. Digitization was accomplished by an ND converter that was added to a GMRR computer. Phase III tasks Included preparation of software for digitization, computer-computer communication, data processing, and statistical analysis. Useable data were obtained from eleven half-hour tapes containing noise from one axis of the primary antenna and three axes of the remote antenna. The overall average Improvement in SNR was 4.1 dB. However, the average Improvements for the Individual X, Y, and Z axes were 4.2, 11.9, and -1.9 dB, which roughly follow the observed noise power. Nonlinear processing was not effective with this noise.

Jan 2, 1984

By Frank B. Fulkerson

Aluminum production in the Pacific Northwest has a new potential for expansion and increased stability of operation. This new potential results from greater availability of power; lower freight rates on alumina and aluminum; good market prospects for the metal, including western aluminum market expansion following a decline in defense requirements in the 1950's; and possibility of developing bauxite deposits in the Pacific Basin as well as other mineral resources. INTRODUCTION This is a report of a special study by the Bureau of Mines of the primary aluminum industry of the Pacific Northwest. It outlines developments relative to the United States as a whole.

Jan 1, 1962

By Candice Stevens

The Territory of Afars and Issas is to receive its independence from France on June 27, 1977. The Territory's economic income was based on entrepôt trade through the port of Djibouti and trans-shipment of goods on the Chemin de Fer Franco-Ethiopian (CFE) railroad. The Territorial budget was scheduled to in- crease from $32.6 million3 in 1976 to $36 million in 1977, despite severe shortfalls in 1976 stemming from inflation and a persistent balance-of-trade deficit. Subsidies from France continued to sustain the economy, and the French pledged to provide approximately $140 million in aid annually after independence. In 1976, financial agreements were concluded with a number of Arab oil-producing countries, including Saudi Arabia which granted $10 million toward development projects. The new Republic of Djibouti is scheduled to become the 49th member State of the Organization of African Unity (OAU) and the 21st member of the Arab League, and to receive aid from their financial institutions. The port of Djibouti and the CFE railroad constituted the Territory's main economic resources. Traffic at the port greatly

Jan 1, 1980

By Richard A. Dick

Underground blasting in permanently frozen gravel was studied in a 7-by 12-ft drift by running a nonreplicated 2 X 2 X 2 factorial experiment on the effects of type of cut, delay, and explosive on the fragmentation subsystem. Comparisons were made between a V-cut round and a burn-cut round, millisecond delays and half-second delays, and 40 percent special gelatin and 60 percent high-density ammonia dynamite. The number of large blocks in the muck pile) loading time, shuttle car operating time lost because of cleanup needs, length of advance per round, and length of muck pile were recorded and statistically analyzed. None of the blast parameters had a significant effect on the length of advance or length of muck pile, although the half-second delays tended to give a shorter muck pile than millisecond delays. The burn cut required less secondary breakage, less loading and cleanup time, and gave better overall fragmentation than the V-cut. The ammonia dynamite shots required less secondary breakage and less loading time than those using special gelatin. The half-second delays gave better overall fragmentation and required less cleanup time, but the millisecond delays gave a better loading rate. None of the differences between delays and explosives were notably significant.

Jan 1, 1970

By L. A. Neumeier

The Bureau of Mines evaluated creep properties of Zn-Cu-Ti alloys that were annealed after finish-rolling either cold) or at 480° F (249° C). Compositions ranged up to 1.25 pct Cu and 0.36 pct Ti. Most data are for sheet annealed after finish-rolling to 92-pct total reduction. Annealing times were varied at temperatures between 320° and 560° F (160° and 293° C). For a number of the alloys, annealing after hot-rolling at 480° F affects creep properties very differently in longitudinal and transverse sheet directions. The detrimental result is that the anisotropy in creep properties between the two directions can be vastly increased. Conversely, specific annealing treatments of certain heavily cold-rolled alloys result in surprisingly low anisotropy in creep properties and the low anisotropy coincides with excellent creep resistance for both directions. Supplemental data are presented on tensile, hardness, and thermal expansion properties, and microstructures.

Jan 1, 1972

By Paul M. Ambrose

THE ABRASIVES INDUSTRY throughout the world enjoyed a profitable year. With the exception of tripoli, the quantity of each kind of abrasive produced in the United States was greater than for any of the past 5 years and value of each was greater than for many years. Production of silicon carbide both in the United States and in Canada was the largest since 1960. Abrasive machining, which offers great potential for the increased Use of aluminum oxide, contributed to increased industrial productivity. Diamonds from the sea off the coast of South-West Africa attracted wide interest. Much of the production from this source has been gem diamond, and there is little likelihood of significant quantities of industrial diamond from that source. Manufactured diamond from all free-world sources was sold in the United States in 1964.

Jan 1, 1965

By Fred V. Carrillo

Of the total quantity of secondary copper and zinc that became obsolete in the United States from 19b1 through 1970, more than 11 million tons of copper and 10 million tons of zinc were not recovered. These estimates are based on a study of the flow and recovery of old copper and zinc scrap by consumption end-use. This report describes (1) where copper and zinc are being used; (2) when they become obsolete and available as secondary metal; (3) how they are being collected for recycling; and (4) how much might be recovered from scrap that presently is not being recycled.

Jan 1, 1974

By Richard A. Winters

There are no producing or developing mines or active mining claims in the Deschutes Canyon RARE II study area. Only two prospects were found; they have no identified potential for mineral resources. Thin diatomite deposits occur in the Pliocene Madras Formation. Development of sand and gravel deposits in the area could not favorably compete with similar deposits in the surrounding area which are closer to points of use. By mid-1982, active oil and gas lease applications covered about 25 percent of the area, a reduction from nearly 100 percent in early 1981. No holes were drilled for oil and gas exploration. INTRODUCTION Personnel of the Bureau of Mines, Western Field Operations Center conducted a mineral investigation of the Deschutes Canyon RARE II area during the summer of 1982. The area, about 10 mi (16 km) southwest of Madras, Oregon, covers 10,890 acres (4,407 ha) in the Crooked River National Grasslands (fig. 1). The Deschutes River has incised a deep canyon into the north sloping elevated lava plain near the transitional boundary of the High Lava Plains and the Deschutes-Umatilla Plateau geomorphic divisions (Baldwin, 1964, p. 20).

Jan 1, 1983

By Stephen C. Tadolini, Thomas M. Barczak, Peter (Yunqing) Zhang

A cooperative study was conducted with Emerald Coal Resources, L.P., an affiliate of Foundation Coal Corporation, and the National Institute for Occupational Safety and Health (NIOSH) to evaluate the effectiveness of (partially) pre-driven longwall recovery rooms supported with pumpable roof supports. This paper evaluates the load transfer mechanics associated with the advancement of the longwall face into the pre-driven recovery room and the widening of the room to recover the longwall shields. The results show that the yielding of the panel fender produced uncontrollable convergence that caused yielding of the shields and stiff pumpable roof supports when the face was approximately 10 ft from the recovery room. The shields continued to yield until the face advanced into the recovery room. Convergence in the pre-driven recovery room typically reached 6-8 in once the pumpable supports yielded and shed load through a declining residual load capacity prior to being cut out by the longwall shearer. Roof deformations occurred beyond the 32-ft horizon with total deformation ranging from 2 to 4 in, indicating that standing support was necessary to help control the span as the longwall face advanced into the pre-driven recovery room. Stability improved as the pumpable supports were cut out, thereby reducing the span between the shields and the outby pillars. In the end, the shields were successfully recovered under stable ground conditions. However, a disconcerting discovery was the load shedding of the outby pillars as the recovery room was mined into. It is postulated that this may be due to the progression of the rear “abutment” moving toward the recovery room as the panel fender and standing support in the recovery room yield and shed load. This behavior was not expected with a relatively narrow room that is fully supported with standing support. If this mechanism is indeed occurring, the width of the room and performance of the standing support becomes even more critical. Premature failure of the support can lead to excessive convergence on the shield line that cannot be controlled even with modern shields, resulting in roof instabilities that can lead to catastrophic results.

By Eleanor Abshire

THIS PUBLICATION is the third to be prepared as a result of a cooperative project by the Bureau of Ships and the Bureau of Mines for accumulating literature published on zirconium and hafnium. The undertaking also resulted in the establishment of an information center on zirconium and hafnium at the Bureau of Mines station at Albany, Oreg., for the use of research organizations and others. The present bibliography consists of references (with abstracts) to pertinent literature on zirconium. The first publication in this series was Information Circular 7771, Bibliography of Zirconium, published in April 1957. It consists of 969 abstracted reports and 645 U.S. and foreign patents. The second publication, called a supplement to Information Circular 7771, is numbered Information Circular 7830 and consists of 844 abstracted reports and 62 U.S. and foreign patents. It was published in October 1958.

Jan 1, 1962

By O. C. Blade

Sales of diesel fuel in the United States exceeded 150,000,000 barrels during 1953 and 140,000,000 barrels during 1952. Following are some figures on the distribution of this fuel computed from data issued by the Bureau of Mines. 2/ [ ] Deliveries of diesel type fuel from refineries totaled 91,170,000 barrels during the first six months of 1954, 3/ a corresponding figure for 1953 was 86,284,000 barrels.

Jan 1, 1954

By William J. Campbell

This report describes a Bureau of Mines study undertaken to determine the applications and limitations of solution techniques as a general method of fluorescent X-ray spectrographic analysis. Systematic errors due to variations in particle size, surface preparation, and sample inhomogeneity are eliminated by the use of solutions. The range of applicability of fluorescent X-ray spectrography is increased in two ways: (1) Samples in the form of wire, filings, turnings, etc., can be analyzed as solutions, and (2) samples submitted as solutions can be analyzed as received 0 The lower limit of detectability varies from 0.14 gram per liter for sulfur, atomic number 16, to 0.0015 gram per liter for strontium, atomic number 38. Most elements have limits of detectability between 0.02 and 0.002 gram per liter.

Jan 1, 1959

By R. W. Stahl

An emergency is defined as an unforeseen combination of circumstances that calls for immediate action. When applied to a coal mine, an emergency may call for prompt removal of the men to the surface through travelways other than the haulageway or intake airways, which are generally contaminated with irrespirable air as a result of an explosion or fire. Therefore, maintenance of adequate and travelable escapeways from all working areas of a mine is vitally important insurance against disaster. Several mine disasters could have been avoided if well-defined escape routes had been provided and made known to all mine employees. Such occurrences, unnecessary as they generally are, unfairly indict the industry when only a small segment thereof is involved. As a result of a rather recent disaster, which might not have happened if good escape routes had been provided, the Bureau of Mines decided to delve into the escape procedure to determine (1) what is being done in the industry and (2) what might be done at reasonable cost.

Jan 1, 1962

By Albert L. Toenges

The purpose of this paper is to describe some of the methods and practices of mining coal mechanically where more than one shift is worked, with the view of determining the advantages and disadvantages of various types of equipment and mining systems now in use. This paper is in the nature of a progress report, and, as the number of mines discussed in it is limited, the conclusions drawn in the comparison of various systems are not final but may be revised after subsequent investigations. Physical conditions vary in different and in the same mining districts and determine, more

Jan 1, 1938

This Bureau of Mines publication consists of an overview of the mine waste management research currently being conducted by the Bureau. The following papers, given at a Technology Transfer Workshop, emphasize the increasing importance of research related to the safety and environmental considerations of mine waste disposal In recent years. Current work related to legislation passed in the last 10 years and their subsequent standards includes the development of adequate monitoring systems, development of stability and seepage prediction and control techniques, control of runoff water, and control of leaching solutions. Selected topics are included here that cover coal mine waste disposal, embankment slope stability monitoring, flow failures of mine tailings impoundments, and controlled burnout of abandoned coal mine fires. The projects described provide a current documentation of problems being addressed.

Jan 1, 1981

The Bureau has published much data on sulfur (4, 15, 23)3, most of it dealing with national or international aspects of the sulfur industry. Little information, however, is available on sulfur marketing in specific States or areas, Therefore, the Bureau has conducted a survey of the resources, production, consumption, and economic future of the sulfur and sulfuric acid industry in States of the Central and Southern Rocky Mountain area - Wyoming, Colorado, Utah, Arizona, and New Mexico - and in the Northern Plains States - North Dakota, South Dakota, and Nebraska, even though these States do not represent an economic or marketing unit. The purpose of this survey is to review the demand for sulfur and primary sulfur compounds that draws upon the natural resources of the region, to discover opportunities for better use of these resources, and also to analyze and evaluate the patterns of consumption, sources of supply, and other factors that affect the demand for these mineral products. While this survey stresses the economic and marketing phases of the industry, a complementary report (32) emphasizes the resources of sulfur in Wyoming, Colorado, Utah, New Mexico, and Arizona.

Jan 1, 1962

By Marc Ruest, Lewis Martin

A new instrumented cable bolt has been developed by the National Institute for Occupational Safety and Health at the Spokane Research Laboratory in Spokane, WA. Although various instruments are available to measure load distribution and magnitude along a grouted cable, this instrument is innovative in that it uses strain gauges internal to the cable as load-measuring sensors. The instrument has been successfully tested in the field at FMC’s Granger Mine, Meikle Mine, and Getchell Mine. A “split-pipe” laboratory pull test was performed on each of three cable bolts instrumented with the new device. Each test consisted of grouting a 1.83-m-long cable in two 0.91-m-long sections of schedule 80 pipe. A numerical analysis was then performed in which laboratory boundary conditions were simulated and model properties derived from textbook guidelines. The loads calculated by the model were then compared to the measured loads.