Search Documents

By M. M. Tilman

The Federal Bureau of Mines developed a rolling method that improves creep resistance and yield strengths of lead alloys containing up to 5 wt-pct Sb. The 0.69-inch-thick slab-cast alloys were breakdown-rolled to 0.226 inch and finish-rolled to 0.063 inch at 5-or 20-pct reduction per pass. Rolling was at room temperature to simulate conventional cold rolling, and at 75°, 125°, and 175° C. Two alternative methods evaluated consisted of (1) a single cold final pass followed by annealing and (2) a single hot final pass. Two additional processing methods involving percipitation strengthening were included for comparison. Compared with conventional cold rolling, hot rolling at 125° and 175° C with multiple light passes vastly improves creep resistance and raises yield strengths. Tensile strengths are less affected. The other treatments also improve creep resistance significantly and generally improve tensile properties; magnitudes vary with treatment and composition.

Jan 1, 1975

By Richard L. Fischer

Constant-volume charges of precipitated PETN (pentaeythrite tetranitrate) at three specific gravities (0.50, 1.00, and 1.50) were used in laboratory tests to examine the effects of changes in explosive properties on free-surface displacement pulses and on crater dimensions. The tests were performed in large blocks of cement-mortar. The values for the detonation velocity, detonation pressure, specific energy, energy density, and energy release rate were calculated from the explosive loading density. Calculated explosive properties were correlated with free-surface displacement pulse measurements, strain energy, and measured crater dimensions. Increases in explosive properties resulted in increased free-surface displacement pulse parameters and crater dimensions. The loading density, detonation velocity, energy density, detonation pressure, and energy release rate were found to be best indicators of explosive performance. Simple acoustic relationships involving impedance ratios were examined and could not be used to predict peak displacement amplitude or strain energy. Data are presented in the customary English units as well as the International System of Units (SI).

Jan 1, 1970

By F. E. Armstrong

Tritiated water has been used as a tracer to follow the path of leach liquids as they flow through a copper-mine dump. Semipermeable layers, produced within the dump by compaction and "stratification" of deposized dump material, restrict the vertical movement of water. Knowledge of this restriction would aid in the optimization of the leaching process. The portion of the dump of particular interest was approximately 2,000 feet long, 800 feet wide, and 200 feet high. A total of 94 curies of tritiated water was injected into the dump at the rate of 650 gpm over a period of 39 hours. The leach liquid was sampled at natural surface outflows and through a series of wells, some drilled to the bottom of the dump and others to intermediate levels. More than 3,300 samples were analyzed, most by liquid scintillation counting, but a few hundred by gas counting. Data obtained permitted calculation of flow paths, recycle times, total fluid volume, and estimates of retention times in various portions of the dump.

Jan 1, 1971

By B. S. Covino

The Bureau of Mines has conducted a laboratory and field corrosion test¬ing program to determine materials of construction for the leaching and gas-sparging crystallization environments of the clay-HC1 process in order to more fully utilize the alumina from domestically available kaolinitic clays. Laboratory tests were used to determine the corrosion rates of 22 metals and alloys by weight-loss measurements in these two environments of the process. The results of this laboratory study were used both to suggest metals and alloys for field testing and to determine the effect of the individual solution components on the corrosion behavior of the metals and alloys. Results from the field tests were used to recommend Ta, Ta-2.5W, and Ta-10W for con¬struction of the agitators for the leaching process. The metals and alloys recommended for construction of the gas-sparging crystallizer heat exchangers were Ta, Ta-2.5W, Ta-10W, Nb, Nb-1Zr, Nb-3Zr, Nb-28Ta-10W-1Zr, Nb-10Hf-1Ti, and Zr for the first stage and Ta, Ta-2.5W, Ta-10W, Nb-28Ta-10W-1Zr, Nb, Nb-10Hf-1Ti, and Zr for the second stage.

Jan 1, 1981

By J. J. Demeter

Anthracite from the four producing regions in Pennsylvania was both ashed in the laboratory and burned on a chain-grate stoker to determine the sulfur-retention properties of its ash. The retention of sulfur in laboratory-prepared anthracite ash was shown to be related to ashing temperature and to the amounts of sulfur and calcium present in the coal. At the usual laboratory ashing temperature of 750° C sulfur retention ranged from 0.8 to 13.2 percent of the total coal sulfur. Sulfur retention in the ash was negligible, o to 0.3 percent, at 1,200° C, which is the thermal decomposition temperature of calcium sulfate; thus calcium sulfate does not form and cannot serve as a sulfur-retaining agent. In several tests the anthracite was mixed with 6 or 10 percent dolomite prior to firing in the chain-grate stoker. The dolomite did not improve sulfur retention owing to the high temperature in the fuel bed. Sulfur retention was, however, related to the unburned carbon in the ash. The relationship of the percentage of original coal sulfur retained in the ash (Y) to the percentage of the original carbon in the coal remaining in the ash (X) is expressed by Y = -0.579 + 0.914X. The percentage of sulfur retained is almost directly proportionate to the percentage of original coal carbon in the ash.

Jan 1, 1968

By Donald R. Irving

ALTHOUGH the quantity of material handled at metal and nonmetal mines in the United States in 1962 was 2.7 billion tons, the same as in 1961, a larger proportion was waste. At metal mines, crude ore production declined 1 million tons and waste output rose more than 18 million tons; at nonmetal mines crude ore production declined 6 million tons and waste output rose 36 million tons. Copper and iron ore producers increased their share of crude ore and material handled from about three-fourths to four-fifths of the national metals total, and sand and gravel and stone producers in-creased their share of the nonmetals total, also from three-fourths to four-fifths. Six States-Arizona, California, Florida, Michigan, Minnesota, and Utah-each handled more than 100 million tons of ore and waste, and together they accounted for 43 percent of the U.S. total. When the large-volume construction materials (sand and gravel and stone) were excluded from the totals, four States-Arizona, Florida, Minnesota, and Utah-supplied over half of the material handled.

Jan 1, 1963

By J. W. Thompson, M. N. RICH

That there is wide interest in the preparation and properties of metallic zirconium and its salts is indicated by the many articles recently published in scientific and technical journals and the many patents issued. The compounds of zirconium have numerous important uses and more uses will doubtless be found. In the course of the special work on rare metals that were of military importance during the war, the authors of this bulletin were detailed to the Golden mining experiment station of the Bureau of Mines to prepare metallic zirconium and to investigate its properties. A number of investigations in recent years have indicated that sintered or coherent zirconium metal is very resistive to acids; that it can be used for electrodes, and it probably will find metallurgical uses. A steel containing zirconium has been proposed for use in armor plate and automobile parts, and nickel-zirconium alloys have been suggested for high-speed cutting tools and for cutlery. Numerous articles in scientific journals have recommended the use of zirconium oxide as a refractory, an abrasive, a pigment in paints, and as an opaquing agent in enamel ware. The salts have been used in the textile industry' as a mordant and also for weighting silk. When the authors began their investigation, they found it necessary to collect all of the available literature on the general subject of zirconium and its compounds. Pure salts could not be obtained on the market, and in order to get these, as a preliminary step to the preparation of the metal, the literature had to be classified and the methods of preparing the salts investigated. Also, there was much difficulty at first in making satisfactory analyses, and this phase of the work received careful attention. As it was necessary to begin with a historical review of the literature, such a review is given as Part I of this report, and a bibliography is included as Part IV. References to the numbered items in this bibliography are made throughout the text, the usual footnote references being omitted. Analyses of the products and conclusions as to their purity are given under the descriptions of methods of preparation. A table showing the properties of the amorphous metal, and another showing the properties of the coherent metal, will be found under appropriate headings in Part II. No attempt has been made in the historical review to discuss fully all the published information about zirconium and its compounds, but only such material has been assembled as has a direct bearing upon the present work. Considerable difficulty was experienced in collecting this material because of the confusion of terms by various authors who perhaps did not thoroughly understand the chemistry of zirconium.

Jan 1, 1921

By Gertrude N. Greenspoon

Legislation and Government Programs.-The Occupational Safety and Health Administration (OSHA) held public hearings in early 1975 on proposed standards for exposure to inorganic arsenic. The findings obtained at the hearings will be considered to promulgate emission standards. Domestic Production.-Arsenic trioxide (As203) was produced domestically only at the Tacoma, Wash. copper smelter of ASARCO Incorporated. Production data cannot be published. Output rose 9% over that of 1974, shipments were less than half those of 1974, and stocks rose 31 %. Production of arsenic metal, begun by ASARCO in August 1974, continued in 1975.

Jan 1, 1977

By C. A. Komar

The Bureau of Mines has undertaken an investigation to determine possible applications of acoustic energy at sonic and ultrasonic frequencies to improve ultimate recovery from oil reservoirs. A literature search was conducted to provide background information for initiating laboratory research. The purpose of the literature search was to review the uses that have been made of acoustic energy in the petroleum industry and to select procedures and techniques that could be applied to the solution of petroleum production problems. The characteristics (68)3 of ultrasonic energy make it potentially useful to a variety of industrial and experimental applications. Pulse techniques (99) are common in the testing of materials where inspection is accomplished by propagating an ultrasonic pulse through the material. Viscosity measurements (45) are made by interpreting changes in the absorption of sound as it is propagated through a flowing liquid. Cavitation phenomena (93) produced by high-intensity ultrasound in liquids have been used extensively in industrial cleaning, machining, impact grinding, and aluminum soldering operations.

Jan 1, 1963

By G. E. Johnson

A bench-scale study was made of removing hydrogen sulfide from synthesis gas at elevated pressure by iron oxide impregnated on wood chips. The gas contained 0.02 to 0.06 percent oxygen. The removal of hydrogen sulfide by iron oxide impregnated on wood chips is more efficient at elevated pressure. At constant space velocity, longer periods of operation at 400 p.s.i.g. are possible before the exit gas reaches a given maximum concentration of hydrogen sulfide, compared with 200 p.s.i.g. or atmospheric pressure. In tests at room temperature, 60° C., and 100° C., the most effective removal of hydrogen sulfide was obtained at room temperature and the least effective at 100° C. Dry impregnated wood chips removed only about half as much hydrogen sulfide as chips wetted to a water content of 50 percent.

Jan 1, 1962

By Robert L. Lagace, Michael A. Grossman, Alfred G. Emslie

This supplement to the final report is a collection of interim and monthly reports and working memoranda prepared during the course of this program to document the progress, methods and results of the work. The supplement is divided into the self-contained sections briefly described below. I. SELECTED MONTHLY TECHNICAL LETTER REPORTS - This section is a collection of selected monthly technical letter reports that briefly summarizes the chronological development of the analyses and results, including the different concepts, theoretical approaches, and methods of data reduction and analysis explored, and the discoveries, insights and findings made along the way. More detailed treatments of the key developments and results are presented in the interim reports and working memoranda reproduced in subsequent sections of this supplementary report, and in the separately published final report. II. BACKGROUND THEORY FOR MEASUREMENT PROGRAM ON MEDIUM AND HIGH FREQUENCY RADIO TRANSMISSION IN COAL SEAMS - Working Memorandum - This working memorandum gives the initial background theory needed to guide the planned measurements and data analyses of this program to describe the propagation of radio waves-in coal seams for the frequency range of 50 to 5000 kHz. III. MODELLING AND DATA ANALYSIS OF IN-MINE ELECTROMAGNETIC WAVE PROPAGATION - Interim Report - This interim report presents detailed treatments of the data analysis and modelling techniques used, and the associated results obtained from conductor-free area propagation data measured by T. Cory in the first set of six coal mines. The mines were located in three highcoal seams; the Pittsburgh seam in northern West Virginia, the Pocahontas No. 3 seam in Virginia, and the Herrin No. 6 seam in Illinois. IV. ANALYSIS OF MF PROPAGATION DATA FROM MARGARET NO. 11, NANTY GLO, EHRENFELD, AND ADRIAN COAL MINES - Interim Report - This interim report presents detailed treatments of several improved data analysis and Modelling methods applied to, and results obtained from, conductor-free area propagation data measured by T. Cory in the second set of four coal mines. These mines were located in three low-coal seams; the Upper Freeport seam in Pennsylvania and West Virginia and the Lower Freeport and Lower Kittaning seams in Pennsylvania. In addition, this report contains a reprint of two papers presented at a Bureau of Mines sponsored EM Guided Waves in Mine Environments Workshop held in Boulder Colorado. One paper describes the three-layer theoretical model and its application to the conductor-free data from the first six mines, while the second paper describes the theory developed for the coupling of loop antennas to a cable in a mine tunnel in a coal seam, and the model's application to data in the vicinity of cables taken at the Margaret No. 11 mine. V. A METHOD FOR NONINTRUSIVE, IN-SITU MEASUREMENT OF COAL AND ROCK CONDUCTIVITIES IN A COAL MINE TUNNEL - Working Memorandum - This working memorandum briefly describes a possible direct method, and its potential advantages and shortcomings, for performing in-situ measurements of coal and rock conductivities. VI. MODELLING AND DATA ANALYSIS OF IN-MINE ELECTROMAGNETIC WAVE PROPAGATION FROM 50 to 5000 kHz - Interim Report - This interim report presents a summary comparison of theoretical and experimental results for conductor- free areas in eleven coal mines located in seven coal seams. It also summarizes the findings and their implications for intrinsically-safe, portable radio communications between roving miners.

Jan 2, 1980

By Daniel G. DiCanio

This report describes a computer-based model for estimating the tangible costs of injuries and deaths from work-related accidents in underground coal mines. The study undertook to identify and quantify the elements of accident costs, including field visits to coal mines, insurance carriers, and public agencies. The mathematical models developed for each tangible element of accident cost are presented in Volume I -of the report. A listing of the computer programs which comprise the model and instructions for using the programs are presented in Volume II. Statistical distributions of mining family characteristics, data on 95 miners killed in underground accidents, and other basic data used to develop the model are presented in Volume III. Application of the model to a data base of 9,286 accidents which occured in underground bituminous coal mines during 1974 yielded a total of $56,900,000 in tangible costs to industry, mining families, and public agencies. Loss of income to the families of miners injured or killed in these accidents accounted for 47 percent of the total.

Jan 1, 1976

By Robert S. Sanford, Harold C. Pierce

"At one time the Alaskan Eskimo lived in many small settlements scattered along the Arctic coast. These settlements extended as far south as Bristol Bay and several miles inland on the large rivers. When the white man established trading posts, schools, hospitals, and missions, these people gradually congregated around them in a few large villages. The natural fuel supply near many of the large villages along the Arctic coast became exhausted as a result of the abnormally large influx of people from small outlying settlements.The population of Barrow, Alaska, according to the 1940 census, is 363 persons, but since that time it has increased considerably, and later estimates place the present population between 400 and 500 persons. With the exception of 25 white persons, the entire population is comprised of Eskimos.The government maintains a school, hospital, radio station, and weather station at Barrow. In addition to the government, installations, there is a church, a privately owned trading post, and cooperative store owned by the Eskimos.For many years the Barrow Eskimos depended on driftwood and petroleum residue from Cape Simpson for their fuel supply. This fuel provided not only warmth for the Eskimo during the long cold winters but also heat for melting ice, the only source of 'water during .the winter. In recent years the sources of petroleum residue and driftwood have not been adequate to meet the demands for fuel During the winter of 1942-43 and again in 1943-44, Barrow experienced an acute shortage of fuel.The fuel problem at Barrow was brought to the attention of Governor Ernest E. Gruening, who was instrumental in getting a Bureau of Mines engineer4/ to investigate reported coal occurrences in the vicinity. Coal deposits along the Meade River and at Peard Bay were examined during the spring and fall of 1943. The Alaska Native Service shipped in mining equipment in September 1943 and commenced stripping an open-pit mine on the Meade River in June 1944. In conjunction with this work, an engineer5/ of the Bureau explored by churn drilling to determine the tonnage of- coal in the vicinity of the mine. In addition to this work, the Bureau of mines examined coal deposits in Peard Bay area and along the Kuk River south of Wainwright."

Nov 1, 1924

By A. G. Smelley

As part of research conducted in its mission to effect pollution abatement, the Bureau of Mines, U. S. Department of the Interior, is developing a dewatering technique that allows for disposal of phosphatic clay wastes, for reuse of water now lost with clays, and for reclamation of mined land. The technique utilizes a high-molecular-weightnonionic polyethylene oxide polymer (PEO) that has the ability to flocculate and dewater phosphatic clay wastes. A synergistic flocculation study was made to determine whether a portion of PEO could be replaced by other reagents. Several groups of reagents were tested: (1) those that increased the zeta potential of the phosphatic clay wastes; (2) those capable of hydrogen bonding; and (3) those which flocculated the phosphatic clay waste. Reduction in PEO consumption occurred only with addition of those reagents able to flocculate the slime. The use of natural guar gums resulted in a lower PEO requirement and also yielded a dewatered product of higher solids content, 43 to 45 percent, versus 33 to 35 percent obtained with PEO alone.

Jan 1, 1980

By V. R. Spironello

One of the primary objectives of the Bureau of Mines solid waste utilization program is the recycling of the magnetic fraction of municipal solid waste called raw refuse scrap. In this investigation, several types of scrap of differing quality, including refuse and turnings, were melted in a 1-ton electric-arc furnace in various combinations to produce steel in noncritical (construction) grades. In-formation on furnace operation and on the behavior of tramp and alloying elements was obtained. The research showed that it is possible to produce acceptable steel from a variety of steel scrap. Although some scrap is routinely used in steelmaking, it was found that up to 50 to 55 pct of the scrap charge can be ref-use, provided it is combined with higher quality scrap. The chemistry of the steels was generally acceptable, and all of them were rolled without difficulty. The specification (ASTM 615) for the steels produced was grade 40 or grade 60, containing 0.30 or 0.40 pct C, with mini-mum yield strengths of 40,000 or 60,000-psi, respectively. Most of the steels met the specification requirements. In-formation on typical microstructures of some of the steels is included. The composition of some furnace dusts showed high levels of Sn, Pb, and Zn.

Jan 1, 1981

By Jay F. Colinet

Respirable dust exposure has long been known to be a serious health threat to workers in many industries. In coal mining, overexposure to respirable coal mine dust can lead to coal workers? pneumoconiosis (CWP). CWP is a lung disease that can be disabling and fatal in its most severe form. In addition, miners can be exposed to high levels of respirable silica dust, which can cause silicosis, another disabling and/or fatal lung disease. Once contracted, there is no cure for CWP or silicosis. The goal, therefore, is to limit worker exposure to respirable dust to prevent development of these diseases. The passage of the Federal Coal Mine Health and Safety Act of 1969 established respirable dust exposure limits, dust sampling requirements for inspectors and mine operators, a voluntary x-ray surveillance program to identify CWP in underground coal miners, and a benefits program to provide compensation to affected workers and their families. The tremen­dous human and financial costs resulting from CWP and silicosis in the U.S. underground coal mine workforce are shown by the following statistics: ? During 1970?2004, CWP was a direct or contributing cause of 69,377 deaths of U.S. underground coal mine workers. ? During 1980?2005, over $39 billion in CWP benefits were paid to underground coal miners and their families. ? Recent x-ray surveillance data for 2000?2006 show an increase in CWP cases. Nearly 8% of examined underground coal miners with 25 or more years of experience were diagnosed with CWP. ? ?Continuous miner operator? is the most frequently listed occupation on death certificates that record silicosis as the cause of death.

Jan 1, 2010

By M. C. Malamphy

A general description of the activities and results of bauxite investigation by The Bureau of Mines at its bauxite project in Saline and Pulaski Counties, Ark., has been given in Report of Investigations No. 4251. The factual data obtained during the project are reported in a series of Reports of Investigation beginning with No. 4251, of which this is the fourth. The data are accompanied by maps showing the location of holes drilled and the deposits developed. Each area upon which work was done is reported by half townships. Each bauxite deposit investigated was assigned a name and a number for ready reference and identification, and its location and name are shown on the appropriate half-township map. The description of each half township is followed by a description of each deposit developed in that half township. The 14 half-township maps and 77 detail maps of the bauxite deposits in this series of reports give the locations and numbers of all the holes drilled on the project except the deep holes drilled to test the geophysical anomalies. The locations of those holes show on Figure 13 in Volume 1. The descriptions of the deposits developed are followed by complete detailed logs of the drill holes. Many of the widely spaced exploratory holes did not discover bauxite of minable thickness and grade. The pertinent information obtained from the widely spaced exploratory drill holes has been summarized and tabulated, and a table for each half township-is given with the discussion covering that area.

Jan 1, 1948

By R. E. Chaney

This report summarizes the research on the Strategic and Critical Materials Program tasks conducted at the Idaho National Engineering Laboratory (INEL) between May 1984 and April 1985. The work is divided into two areas: 1. Production Technologies - Tasks directed at developing advanced extraction technologies ? Biologically-Assisted Minerals Processing ? Metal/Gas Reactions and Thermal Plasmas ? Dehydration of Aluminum Chloride Hexahydrate (completed). 2. Conservation/Substitution Technologies - Tasks directed toward establishing the technical processing base which will permit the use of advanced materials ? Joining of Rapidly Solidified Alloys (RSA) ? Joining of Silicon Nitride-Based Ceramics ? Nondestructive Evaluation of Ceramic and RSA Joints and Materials ? Substitute Catalytic Materials for Platinum.

Jan 1, 1985

By W. Hermanson

This report presents the results of a task to complete a final design of a remote controlled hi-roof bolting machine for high roof areas in coal mines. The project was begun by visiting several coal mines to become familiar with roof fall areas. Several machine concepts were generated and presented to the design committee for criticism. A preliminary design was completed, as covered by this report. A Final Design and Final Report will be issued incorporating the committee comments at the Preliminary Design review and comments received concerning this Preliminary Design Report.

Jan 1, 1979

By L. C. IlsLey

Permissible electric nine lamps are approved with the. understanding that if actively marketed they will be listed in Bureau of Mines publications so that state mine departments, compensation bureaus, mine operators, miners, and others interested in safety equipment for mines may know the permissible lamps available and the important safety features of each. The last list of permissible electric mine lamps was issued as Report of Investigations 33045 in June 1936, a supplement to Bulletin 332.6 All lamps described in Bulletin 332 are either obsolete or have been materially modified, as covered by extensions of the original approvals. These modified lamps and the new designs approved since 1930-totaling 12 cap lamps and 23 lamps of miscellaneous types-comprise the present list of actively marketed permissible electric mine lamps. This bulletin presents the Bureau's test requirements and procedure relative to permissible electric mine lamps and describes briefly the lamps, giving tabulated details of each.

Jan 1, 1942