Search Documents

By J. E. Zeilinger

This Bureau of Mines study was conducted to determine the sulfur reduction potential attainable when washing fine-size coal on a spiral concentrator. Crushed samples of Middle Kittanning and Bakerstown bed coals washed on the spiral provided pyritic sulfur reductions of up to 90 percent for the plus 200-mesh material. Pyritic sulfur reductions on the minus 200-mesh material seldom exceeded 30 percent; consequently, this material would require further treatment. The capacity of the spiral was 2 tph per unit when washing l4-mesh by 0 coal. The ability to remove pyrite combined with the higher-than-expected capacity makes the spiral worthy of consideration as a rougher-cleaner in new fine-coal desulfurization circuits.

Jan 1, 1976

Reduce shaft sinking costs and workers exposure to mechanical hazards, drill dust, blast dangers, and fumes. Approach Replace drilling and blasting by using a large, cab-mounted impact breaker suspended from the bottom work deck of the galloway. How It Works The pneumatically actuated impact breaker is positioned by an articulated boom con-trolled from an operators cab. The breaker delivers 2,000 ft-lb blows that fragment the rock at the shaft bottom. Mucking is accomplished by a backhoe bucket on an articulated boom mounted on the cab. See photograph. The mucked material can be removed either by dumping into a previously drilled borehole or by being lifted out in a muck bucket as shown in the drawing. Positioning of the breaker, rotating the cab around its vertical axis, and moving the cab support frame around the perimeter of the shaft are all controlled by one joystick. Separate controls position the mucker boom, which can be swung horizontally through a 180° degree arc towards either side of the cab. Because the cab can be rotated to any position around its vertical axis, and can also be moved in a horizontal circle around the shaft, virtually any position on the bottom of the shaft can be reached by the breaker and mucker.

Jan 1, 1981

By Frederick H. Raab

The electromagnetic retransmission system is a new, automated method of locating trapped mine workers. This technique overcomes many 1 imitations inherent in electromagnetic direction finding by reducing the effects of the conducting ground to an acceptable maximum, by finding position accurately in the presence of antenna tilt, and by eliminating the need for the receiver to be located directly above the subsurface transmitter. Three transportable three-axis magnetic-dipole transmitters on the surface create a system of electronic grids in which the phases of the downlink Signals convey position information. The subsurface retransmitter modulates the uplink carrier of the existing beacon transmitter with the received downlink signal; the coal-pillar loop antenna is used for both receiving and transmitting. The uplink receiver uses a three-axis antenna and extensive digital signal processing. A small computer integrates data, estimates position, and controls system operation through VHF-FM communications. Both coal-mine and deep-mine operation are possible by selecting appropriate transmitting power and signal frequencies. This report shows such systems to be both feasible and practical.

Jan 1, 1980

By George S. Rice, F. B. LANEY, A. J. Lanza, Edwin Higgins

Under its organic act the Federal Bureau of Mines is directed to conduct investigations relating to the improvement of health conditions in the mineral industries. This report describes the lead and zino deposits and the mining methods employed in the sheet-ground area of the Joplin district, Missouri, and discusses the causes and the methods of abating rock dust in the mines, the chemical and physical characteristics of the dust, and the quantities present in mine air. Although the preliminary investigation included a number of the "soft-ground" mines, the writer spent the larger part of his time in the sheet-ground mines, for in them alone was siliceous dust found in appreciable quantities. Some results of the preliminary investigation have been published by the Bureau of Mines in Technical Paper 105.a The territory covered in t~lCpreliminary investigation, during the period between November 7 and December 6, 1914, embraced parts of Jasper, Lawrence, Newton, and Greene Counties, Mo., and outlying districts in Kansas and Oklahoma. The remainder of the field work, to which 84 days during the period from February 9 to July 19, 1915, were devoted, was confined to the sheet-ground mines, the most important of which are situated in the vicinity of Joplin, Webb City, Carterville, and other smaller near-by towns in Jasper County, Mo.

Jan 1, 1917

By J. M. Stuve

Provisional values for the heat of formation of europium trichloride and europium sesquioxide were determined by solution calorimetry utilizing europium metal of more than 99-percent purity. The resulting values for the heats of formation of Eu203 (cubic) and EuCls (hexagonal) were -386,970 ±l,200 cal/mole and -218,740 ±650 cal/mole, respectively, measured at 298.15° K.

Jan 1, 1965

By Neal M. Miur

"INTRODUCTION The Mineral Ridge-Clay Lick fault system in Crittenden and Livingston Counties, Kentucky, is one of the larger and more important fault systems of the Western Kentucky Fluorspar district. Total production from it up to July 1945 (chiefly since 1900) was approximately 80,000 tons of fluorspar ore, 10,000 tons of which came from the Mineral Ridge Fluorspar Co. tract 1, which was being operated by the Mahoning Mining Co. of Rosiclare, Ill. The fluorspar ore carries lead and zinc that can be recovered by milling, and the Mahoning Co. planned to log-wash the ore at the mine and then mill it in its mill at Rosiclare, The Mineral Ridge Fluorspar Co. properties were examined by O. M. Bishop, an engineer of the, Bureau of Mines, in August 1942. During 1943 and 1314, developments on the properties were under observation by X. B. Starnes, of the Bureau, and it was decided to diamond-drill tracts 1 and 2, as indications seemed favorable for opening up additional fluorspar ore bodies. Drilling was begun March 12, 1945, and was completed July 2, 1945, during which time 12 holed were drilled on tract 1 of the Mahoning Co.'s leases for a total of 3,637.1 feet, and one hole 359 feet deep was drilled on tract 2 of the Jennings lease. The Mineral Ridge-Clay Lick fault system, 4 to 47 feet wide, was encountered in all holes at 126 to 265 feet."

Apr 1, 1947

By M. E. Adam

This report describes the construction and testing of large (30 ft high by 55 ft wide) stopping and overcast structures in an oil shale mine. The work was undertaken to develop construction techniques and cost data, and to measure leakage rates on full scale structures in an oil shale mine. A design data base was developed by reviewing industry practice, oil shale industry plans, and technical literature. Alternate layouts for room and pillar mining were examined to find ways to reduce the size and number of ventilation control structures. Six full size stoppings and one overcast were built in the Colony Pilot Mine. Leakage rates were measured using both SF6 tracer gas techniques and the ?brattice window? method. The leakage was measured both before and after a full scale face blast. Blast air pressures were measured across two of the stoppings. Cost and leakage data were used to evaluate the projected overall performance of various combinations of the stoppings in a two-panel oil shale mine.

Jan 1, 1986

The STATE MINERAL SUMMARIES publication provides estimated data and summaries of mineral activities at the State level for 1993. Most of the estimates are based on nine months data. Individual State summaries are published separately as State Mineral Industry Surveys and copies can be obtained from the appropriate State mineral officer. In an effort to facilitate the rapid dissemination of information and publications produced by the U.S. Bureau of Mine, an electronic document dissemination system is now available for use. MINES FaxBack is a simple-to-operate automated fax response system that operates 24 hours a day, seven days a week. All a user needs is access to a fax machine with a touch-tone telephone. MINES FaxBack can be accessed by calling (412) 892-4088, using the touch-tone telephone attached to the user's fax machine. After calling MINES FaxBack, the requester is guided by a series of voice messages to assist in ordering the desired documents.

Jan 1, 1994

By C. F. Jackson

This paper has been prepared as a progress report in connection with the series of articles on mining methods and costs which are being published by the U. S. Bureau of Mines in the form of information circulars. When enough circulars have boon completed it is planned to publish a more complete and comprehensive paper in bulletin form dealing with the subject of underground transportation. Progress reports, followed b., bulletins, will be prepared from time to time dealing with other subjects included in the general study of mining methods at individual nines, such as mine development, drilling, and blasting; stoping methods (each principal stoping method to be summarized in a separate paper); Ventilation; wage, contract and bonus systems, etc.

Jan 1, 1931

By W. A. Selvig

EQUIREMENTS of montan wax for industrial use in the United States before World War II were met by imports, nearly all of which came from Germany. An important industry for extraction and refinement of this wax from certain brown coals had developed in Germany. At the beginning of the war, montan-wax imports were shut oft, and American industry was forced to rely largely on substitutes. Since the war, relatively small amounts have been imported from Czechoslovakia. Because of the shortage of montan wax at the close of the war and the fact that industry in the United States had to rely on foreign sources in the past, this investigation was started in 1945 to determine probable yields of wax from domestic lignite. Results of the investigation and the properties of extracted waxes are described in this report. Also included in the report are discussions of the occurrence and geology of lignite deposits of the United States from which samples were obtained for wax extraction and the petrographic composition of lignites, particularly in respect to those components that contribute to wax yields.

Jan 1, 1950

By Herbert H. Einstein

The thrust of research reported in Part I was to collect in-situ data from exploration programs and the published literature, and to empirically establish distributional patterns for these variables. Since discontinui¬ties in a rock mass govern to a large extent its engineering properties and thus the performance of any slope in the mass, work has been devoted to determining the appropriate distributional forms for attitude spacing and length of discontinuities and to distributional properties of resis¬tance and deformability parameters. The conclusion from these analyses is that trace lengths are logNormally distributed and that joint spacing is Exponentially distributed, regardless of orientation of the sampling line, and regardless of whether each joint set is considered separately or not. Joint orientation (attitude) data representing 22 individual joint sets from eight sites (a total or approximately 20,000 joints), do nor strongly support any of the commonly used distributions as broadly applicable in practice. The autocorrelation )f geometric joint properties is also examined. However, no significant spatial correlation could be found even after extensive data manipulation. The investigation of resistance and deformability parameters starts with a review of mechanisms and models that are used to represent them. Review and statistical evaluation of approxi¬mately 2,000 discontinuity shear tests has shown that good statistical estimates for use in reliability analyses can be obtained for friction angles.

Jan 1, 1979

By R. A. Isberg

This report describes the design and implementation of UHF radio and closed-circuit television systems in the Black River room and pillar limestone mine near Butler, Pendleton County, Kentucky. Prior to designing the radio system, measurements of signal attenuation on 812 and 466 mHz were made in the slope tunnel and in the straight and level crosscuts in the mine. Two distributed antenna systems fed by two sets of base stations provide approximately 75o coverage of the mine. Passive reflectors are used for extending signals into intersecting crosscuts and two-way signal boosters will be used to extend signals to the perimeter and obstructed areas of the mine. Fourteen mine vehicles were equipped with mobile radios equipped with digital identification, alarm and status encoders. Fifteen portable transceivers also were used. Six closed-circuit television cameras provide surveillance of critical transfer points of the belt conveyor system, and the loading dock at the base of the slope and an ash disposal area in the mine. Two-way radio communication and closed-circuit television have saved considerable man. hours, increased production, reduced maintenance costs and enhanced safety. Innovative developments were the use of passive reflectors and two-way signal boosters for extending signals into intersecting crosscuts, development of lightweight signal margin measuring equipment, modifications of mobile digital encoders to automatically send status information from mine vehicles such as numbers of loads of ore delivered, hot engine, etc., and the use of CATV technology for multiplexing audio, digital and video signals onto coaxial cables from the surface to the mine.

Jan 1, 1981

By G. Gavan

Analysis of reported injuries for off-highway haul trucks indicated that 42.7% were slip and fall, and of these 34.1% occurred mounting and dismounting the machine. Redesign of the lower steps was concluded to provide the most overall improvement for increased safety and accident reduction. Various existing, innovative and conceptual designs were reviewed and evaluated. The most promising candidate designs were the four-spring supported lower steps and the center tube mounted lower steps. Both configurations proved to be viable designs as they passed successfully human factors and survivability tests conducted at a large copper mine.

Jan 1, 1979

By W. E. Pittman

The Bureau of Mines, as part of its Health and Safety Technology Program, is conducting research on the use of ground penetrating radar (GPR) for mine hazard detection. GPR offers a possibility of mapping immediate below-surface geologic conditions, including faulting and other anomalies, thereby exposing potential safety hazards to miners. This report summarizes a literature review of the current status of GPR research in and outside the Bureau.

Jan 1, 1984

By Richard J. Mainiero

The Bureau of Mines investigated coal-mine-type short-delay electric detonators marketed by three domestic manufacturers to determine the accuracy of delays and the probability of overlap between adjacent de- lay periods. The Winzer index was computed and compared with the probability of overlap. A close agreement between the Winzer criterion and overlap probability was demonstrated. A permissible blasting unit capable of delivering a maximum firing energy of 4.0 J and a digital oscilloscope were used to measure the delay time with an accuracy of 20.25 ms. Another oscilloscope and a pulse transformer were used to record firing current. Experimental data indicated negligible overlap probability in detonators of shorter delay periods: periods 1 to 4, which correspond to 25 to 250 ms. However, a significant probability of overlap was detected in some detonators of longer delay periods: periods 5 to 9, which cor- respond to 300 to 500 ms.

Jan 1, 1985

By W. H. Eddy

The Bureau of Mines conducted laboratory batch-and small-scale continuous flotation processing tests on waste granite fines from Georgia, to determine the feasibility of recovering usable feldspar and quartz products by flotation. Two flotation methods were utilized for the removal of biotite and other iron-bearing minerals: One was in an acid-cationic circuit, and the other in an alkaline-anionic-cationic circuit. Feldspar was recovered using an acid-cationic method. To produce commercial-grade feldspar and quartz products it was necessary to employ either two sequential froth flotation circuits or one froth flotation circuit supplemented by wet-magnetic separation techniques to remove iron contaminants. Continuous flotation processing yielded a commercial-grade feldspar concentrate containing, in percent, 3.8 Na20, 5.4 K20, and 1.10 CaO, with recoveries of 77.8, 70.3, and 64.4, respectively. The feldspar tailing was high-quality glass sand containing 98.2 percent SiO2 and 0.024 percent Fe2O3. About 42 percent of the quartz was recovered at glass sand specifications. An effective separation of, potash feldspar from the bulk feldspar concentrate was achieved by batch flotation in a mineral separation cell.

Jan 1, 1974

By Robert G. Bottge

The Bureau of Mines investigated the availability of the land in south-central Alaska for exploration and mineral development of locatable minerals under State or Federal laws. The land ownership for an area of nearly 72.5 million acres in south-central Alaska was divided into 3 availability categories and 15 subcategories. In July 1985, 31.0 million acres of the study area were available for mineral exploration and development, 6.2 million acres were available with restrictions, and 35.3 million acres were unavailable. About 23.6 million acres in the study area are underlain by mineral terranes. About 9.9 million of the 23.6 million acres are available for mineral entry, 2.4 million acres are available with restrictions, and 11.3 million acres are unavailable. While much of the land currently classified as unavailable will be reclassified once it is conveyed to the State or to Native corporations, about 22% of the unavailable lands underlain by mineral terranes are now Federal parks, preserves, wildlife refuges, wild and scenic rivers, and military lands, all of which are considered permanently unavailable for mineral exploration and development.

Jan 1, 1986

By G. G. Morgis

A reasonably clear and broad definition of occupational disease as originated by the Supreme Court of Ohio is: "A disease contracted in the usual and ordinary course of events which from the common experience of humanity is known to be incident to a particular employment." An ailment does not become an occupational disease simply because it is contracted on the employer's premises. It must be one that is commonly regarded as natural to, inherent in, and concomitant of the work in question. The important distinction between accidental-traumatic injuries and occupational-disease injuries is that accidents occur at specific times, ordinarily are discovered readily, and usually leave no question as to the particular employer it whose development the accident occurred. On the other hand, occupational diseases may develop slowly, unknown to the employer and employee until disability occurs, and the injuries sustained are continuing disabilities over an extended period of time and may be incurred while the employee is working for one of several employers.

Jan 1, 1952

By F. P. Haver

Because of increasing concern with air pollution, the Bureau of Mines has developed a hydrometallurgical procedure to obtain elemental sulfur from chalcopyrite (CuFeS2) by means of the following reaction: CuFeS2 + 3FeCl3 ? CuCl + 4FeCl2 + 2S. Under optimum conditions, 99.6 percent of the copper and 71.6 percent of the iron were extracted in 2 hours from a typical mill concentrate containing 75 percent CuFeS2 and 15 percent pyrite (FeS2). At the same time, 68.2 percent of the sulfur in the concentrate was oxidized to the elemental form. The leach was highly selective; gangue minerals, including pyrite, were not attacked, thus accounting for the relatively low recoveries of iron and sulfur. To obtain these results, the concentrate was ground to 98.9 percent minus 325 mesh, and 300 grams was treated with 1 liter of boiling ferric chloride (FeCl3) solution. The FeC13/CuFeS2 ratio was 2.7. Cement copper containing 99.9 percent copper was recovered from the leach solution by cementation on sponge iron. Excess iron, dissolved during leaching and cementation, was removed from the stripped solution by crystallization. Ferrous chloride (FeCl2?4H2O), obtained as a byproduct, was converted to high-purity ferric oxide (Fe203) and HCI by an oxidizing roast. The hydrochloric acid was then electrolyzed to obtain chlorine, which was used to regenerate the leach solution. The leach residue, which contained ~50 weight-percent elemental sulfur, was treated with an organic solvent to recover the sulfur and cyanided to reclaim gold and silver.

Jan 1, 1971

By Albert E. Long

This paper presents a description of the operational mechanics involved in block-caving a granodiorite-capped, limestone deposit. This method was used for 24 years at the Crestmore mine, near Riverside, Calif., which was operated by the Riverside Cement Co. as a source of raw material used to manufacture a portland cement. The Crestmore mine is the only place where a block-cave method has been used to mine a limestone deposit. Structurally, limestone is relatively strong, and it is not usually considered to be a substance amenable to mining by block caving. It is therefore a credit to the engineering department of the Crestmore mine that it developed a satisfactory, relatively efficient method of block-caving a structurally stable rock. In the discussion, covering the methods applied to produce about 7.9 million tons of limestone and granitic rock materials by block caving, particular emphasis has been placed on an assessment of (1) physical properties of the deposit, (2) ground pressure and support, (3) methods used to induce fragmentation and maintain cave action, (4) surface and subsurface subsidence, (5) secondary blasting of oversize, (6) production rate, (7) safety, and (8) the advantages and disadvantages of the cave method as applied to this specific limestone deposit.

Jan 1, 1958