Search Documents

By Richard J. Mainiero

Traditional techniques for the experimental determination of toxic fumes produced by the detonation of high explosives are not applicable to blasting agents. To detonate properly, blasting agents require confinement, a significant booster, charge diameters of 3 inches (7.5 cm) or greater, and charge lengths greater than two-times the charge diameter. Without these conditions, blasting agents will not detonate at full order, leading to a misrepresentation of the gaseous products. A facility for detonating large, confined charges in a controlled volume has been constructed at the Pittsburgh Research Center’s Experimental Mine. The facility consists of a portion of mine entry (once used for full-scale mine explosion research and demonstrations) enclosed between two explosion proof bulkheads. Total volume of the chamber is 9,666 ft (274 m). The chamber is equipped with an air circulating system and is3 3vented using the mine's airflow. Up to 10-pound (4.5-kg) charges can be detonated in the chamber using a variety of confinements. For a typical test, the blasting agent is confined in a 4-inch (10-cm) schedule 80 steel pipe and initiated by a 3-inch (7.5-cm) diameter, 1-inch (2.5-cm) thick Pentolite booster. This combination of confinement and initiation yields a detonation velocity of about 4,000 m/sec for ANFO. This velocity is in line with that measured for blasting in the field. Twenty four 2-inch thick steel plates are suspended around the pipe bomb to stop shrapnel that would otherwise seriously damage the chamber. Following detonation of an explosive in the chamber, a circulating fan is run for about 10 minutes to uniformly mix the chamber atmosphere. Fumes samples are taken out of the chamber through 1/4-inch (0.6-cm) Teflon or polyethylene2tubes for analysis. The fumes are analyzed using bubblers or Vacutainers to collect samples for analysis by the analytical chemistry lab. The technique described here has been employed to determine the fumes produced by the detonation of a variety of ANFO formulations and commercial explosives. This technique may be developed as a standard test to measure fumes produced by blasting agents or may be used to provide data with which to develop a computer model that will reliably predict the expected fumes production based on chemical composition.

By John A. Richards

This paper is one of a series being published by the Bureau of Mines on mining methods and costs. It describes briefly the manner in which slusher hoists and scrapers are used in connection with clock-caving methods at the Emma Nevada mine of the Consolidated Coppermines Corporation, Kimberly, Nev. Kimberly is in the Robinson mining district, White Pine County, 7 miles west of Ely. The district is served by the Nevada Northern -Railroad, which branches from the main line of the Southern Pacific at Wells, Nev., 140 miles north, Paved U. S. Highway 50 from Salt Lake City, Utah, to Reno, Nev., passes through Ely. The altitude at the collar of the Emma Nevada shaft is 7117 feet. The surrounding hills are covered with a sparse growth of juniper, pinon, and mountain mahogany.

Jan 1, 1940

By Edward L. McHugh, Charles Sabine, Jami Dwyer, David G. Long

Slope failure accidents were responsible for about 12% of U.S. surface mine fatalities between 1995 and 2003. Small surface movements on a mine highwall may be precursors of failure that, if detected, could provide sufficient warning to enable workers and machinery to be withdrawn to safety. Radar interferometry offers the necessary precision to detect these movements. Radar has some advantages over other methods in its ability to cover large surface areas for true two-dimensional monitoring day and night under almost any weather condition. Radar’s active transmit/receive mode of operation provides for more direct sampling than do passive optical methods that depend on solar illumination. Improvements in microprocessor speeds and capacities have led to the development of a number of small, portable, ground-based systems; such systems are now being deployed at several locations around the world. As part of an ongoing study of monitoring technologies, researchers from the National Institute for Occupational Safety and Health and Brigham Young University, Provo, UT, cooperated to assess the feasibility of using interferometric radar to monitor mine slope stability. Field tests of a device incorporating prototype equipment were successful in that small, centimeter-scale displacements on rock slopes were detected.

Jan 4, 2006

By J. B. Gayle

Numerous investigators have studied the addition of inert4 substances to coking blends. Generally, the results have yielded trends applicable only to the particular coals and inerts studied. Recently, somewhat more general results were obtained for cokes produced from blends containing added inerts, using the sole-heated oven. The present investigation represents an extension of this work to include a wider range of inerts and to determine the applicability of the various conclusions to cokes produced with the Tuscaloosa oven. The results indicated that an increase in dry-coal charge density of 1 pound per cubic foot (p.c.f.) caused a corresponding change in the hardness (1/4-inch tumbler index) of Tuscaloosa oven cokes of 0.9 percentage points. This value compares favorably with the value of 0.7 determined previously for the sole-heated oven and Bureau of Mines-American Gas Association (BM-AGA) retort.

Jan 1, 1961

By Stanley A. Feitler

This Bureau of Mines report deals principally with the resources and economic aspects of feldspar in the United States east of the Mississippi River. Although in a strict sense, all phases of the feldspar industry affect its economic structure, emphasis in this study is on supply, demand, and marketing. Although feldspar was originally mined for use in the manufacture of pottery and other ceramics, the glass industry, which began to use feldspar in the mid-1920's, now consumes more than half of the annual output. Most mining is open cut, and the methods used are similar to those used in mining crushed b stone. Excess plant capacity has been chronic, and production is usually about 30 percent of capacity fur the industry as a whole. Since 1947, feldspar consumption has grown more slowly than the average for all U.S. industry. This has fostered intense competition, especially for the glass market. Prices have not kept pace with inflation, and profits are small. The trend of consumption through 1970 for glass feldspar is expected to be upward; less rapid in consumption of ceramic feldspar is anticipated.

Jan 1, 1967

By Walter W. Kaufman

The braking performance of underground, rubber-tired, coal mining vehicles is evaluated. Surveys of mining equipment and braking manufacturers and underground stopping tests are discussed as they relate to this evaluation. Stopping performance recommendations are proposed.

Jan 1, 1977

By E. F. Ferrell

Electrowon molybdenum powders and a commercial hydrogen-reduced powder, all with different minor impurities, were investigated by the Bureau of Mines with respect to inherent properties, to fabrication techniques, and to proper-ties of the fabricated sheet. Compared with the commercial hydrogen-reduced powder, the electrowon powders had a larger particle size, a greater flow rate, a higher apparent density, and a lower oxygen content. Sheet materials prepared from the two types of powders showed similar mechanical properties, under the same conditions of heat treatments, except for low-temperature ductility. Yield strengths varied with carbon content, heat treatment, and test temperature.

Jan 1, 1970

By Joseph A. Corgan

The river- or dredge-coal industry of Pennsylvania is conducted on many of the rivers and creeks that drain the Pennsylvania anthracite fields. Coal thus recovered found its way into the streams as coal was being prepared for market by the anthracite industry proper, in the northeastern part of the State. The Principal rivers draining; the fields, those where dredging is taking place, are the Susquehanna, Schuylkill, and Lehigh. Several creeks - the Shamokin, Mahanoy, Wiconisco, and Swatara - also are productive sources of river or creek coal. Operations along the streams cover a wide territory, and along the Susquchanna alone; dredges are recovering coal for about 160 miles. Anthracite was a significant factor in the early industrial development of the United States. Industry used it to generate steam, and railroads used it as fuel for locomotives; but it probably was most important industrially in the smelting of iron ore. For more than a hundred years homes have been heated with this fuel. From the beginning of mining in 1807, to 1940, more than 4 billion net tons of anthracite had been prepared and shipped to market. In the preparation process much of the smaller-size coal and refuse found their way into rivers and creeks which carried the material many miles. This study is concerned with the recovery of that anthracite from those rivers and creeks.

Jan 1, 1942

By Thomas A. Phillips

The Bureau of dines present, an economic evaluation of its process for the ferric chloride leaching of chalcopyrite concentrate. In this process, chalcopyrite concentrate is leached with ferric chloride solution to extract copper, which is precipitated from the solution by electrolysis while leaving sulfur in the residue. Spent liquor from electrolysis is treated with oxygen to regenerate the ferric chloride leach solution and the sulfur-laden residue is processed to recover the sulfur. A cost estimate was prepared for a plant capable of processing 600 tons of chalcopyrite concentrate per day, 330 days per year. The fixed capital cost, on an early 1.975 basis is $27,831,600 and the estimated operating cost is 9.9 cents, per pound of copper product. In comparison, the estimated operating cost of a smelter equipped with a citrate process plant to recover sulfur is about 13.6 cents per pound of copper product. No charge for chalcopyrite concentrate or credit for recovered byproducts has been included in either operating cost. The ferric chloride leach process, therefore, appears to be economically attractive.

Jan 1, 1976

By Maria I. De Rosa

The major fire and fire injury findings for all coal mining categories for 1990-1999 are reported in tables 37-38. Table 39 and figure 13 show the number of fires. fire injuries, risk rates, employees' working hours, and coal production (under- ground and surface coal mines only) by time period for all coal mining categories. Table 40 shows major findings (for under- ground coal mines only) for 1978-1992. For all coal mining categories, 458 fires occurred during 1990- 1999; 157 of those fires caused 164 injuries and 2 fatalities (Ewhr = 2,070 x l0%r, Irr = 0.016: C'P (for underground and surface coal mimes only) - 10,363 x l0\t, Frr = 0.044, LWD = 14,753). Twenty-nine fires and 17 injuries involved contractors. Sixty-six fires required firefighting interventions by mine rescue teams (25 times in underground mines) and fire brigades and fire departments (at least 41 times at surface coal operations). In all, 51 fires destroyed or heavily damaged equipment (including 16 pieces of mobile equipment) because of failure of other firefighting methods, late fire detection, undetected fires, or fire size. A total of 114 fires were detected late, and 42 fires were undetected. The greatest number of fires and fire injuries occurred at surface coal mines; the highest risk rate values were also calculated for this category. For all coal operations, the ignition sources that caused the greatest number of fires were flame cutting/welding spark/slag/flames (1 03 fires or 23% with 69 injuries), hydraulic fluid/fuel sprayed onto equipment hot surfaces (98 fires or 2 1 % with 29 injuries), spontaneous combustion/hot coal (62 fires or 14%), electrical short/arcing (49 fires or 11% with 18 injuries), and conveyor belt friction (3 1 fires or 7% with 6 injuries).

Jan 1, 2004

By Sidney A. Suhler

A field operable, breadboard model, borehole radar was developed for the detection of hazardous geological anomalies in and above a coal seam in advance of mining. A four-inch diameter downhole probe was fabricated and tested in several environments. The radar transmitter was also employed in a cross-hole or through transmission mode to determine natural geotechnical and man-made conditions between boreholes. Sensitivity to underground conditions in both modes of operation were indicated.

Jan 1, 1978

By Bureau of Mines Staff

Coal research and related activities in 1964 by the Bureau of Mines resulted in many advances in the production, preparation, and utilization of this valuable natural resource. Mining research during the year was marked by work on hydraulic mining, coalbed degasification, mine drainage control, mine sealing, strip-mine rehabilitation, and quenching of mine-refuse fires. Bureau research continued to produce information leading to increased safety in underground mining. Such research included roof and rib control via bolting and bonding, pressure monitoring of coal and mine rock during mining operations, and development of safety devices for detecting conditions leading to roof falls. Other safety work was continued on methane detectors, coal-dust suppression, and mine venti lation equipment and techniques. Mine explosion and explosives research, mine equipment and materials, safety rule modernization, and safety education and training of mine workmen were continued. Coal storage and preparation work in 1964 ranged from freezeproofing of lignite for rail shipment, through washability studies of coals and washing equipment, to research on new ways to remove ash and sulfur from coal. Electric power production, which ,accounts for a major portion of the market for coal, received further study. Unique power generation systems, inc luding coal-burning gas turbine and megnetohydrodynamic generators, were intensively investigated. Conventional power systems were improved through continuation of work on furnace performance, powerplant stack gas purification, and engineering and boiler water service.

Jun 1, 1965

By E. G. Noble

The effects of hydrogen chloride (HCI) concentration and temperature on the solubility and hydration state of the alkali chlorides LiCI, NaCI, and KCI and the alkaline-earth chlorides, MgCI2, and CaCl2 were investigated by the Bureau of Mines. Saturated aqueous solutions of the chlorides were sparged with HCI gas at temperatures of 20°, 40°, and 60° C. Increased HCI concentration caused decreased salt solubility be-cause of the common ion effect. Aqueous solubilities for the chlorides of Ca, Li, Mg, K, and Na ranged from 42.6, 45.2, 35.2, 25.5, and 26.1 pct, respectively, at 20° C to 56.9, 49.4, 37.6, 31.0, and 27.0 pct, re-spectively, at 60° C. In solutions sparged to HCI saturation, solubili-ties for these chlorides ranged from 22.4, 26.5, 3.0, 1.3, and 0.05 pct, respectively, at 20° C to 53.2, 48.8, 28.3, 2.6, and 0.8 pct, respec-tively, at 60° C. The solubilities of LiCI and CaCl2 in HCI solution were high because HCI solubility is low in these solutions. The chlo-ride salts of Ca, Li, and Mg formed hydrates, which depended on tempera-ture and HCI concentration. Monohydrates for LiCI, tetrahydrates and hexahydrates for MgCI2, and dihydrates, tetrahydrates, and hexahydrates for CaCl2 were obtained.

Jan 1, 1985

By Robert J. Evans

The Hopper-Feeder-Bolter (HFB) is a prototype multifunctional machine designed to improve productivity by minimizing continuous miner place changes. It is designed primarily to work beside a two-pass continuous miner, bolting on one side and then place changing to bolt the other side while simultaneously providing a surge car and lump breaker located directly behind the continuous miner. Surface testing was conducted at the Bureau of Mines Mine Equipment Test Facility (METF) to evaluate overall system performance and reliability. Tests were conducted to evaluate place changing, tramming, lump breaking, roof bolting, drawbar pull, conveying, temporary roof-support (TRS) capacity, lighting, and noise. Surface test results indicate the HFB is ready to be tested and evaluated underground in a production mode.

Jan 1, 1988

By W. I. Watson

The study considered all the institutional, resource reserve, technological, and economic factors relevant to the industry's present and future status, such as markets and marketing techniques, competition from other producers both domestic and foreign, federal and state regulations affecting the industry, quarrying and processing technologies, slate reserves and resources, and industry structure and economics. Constraints to the growth of the industry were assessed and scenarios proposed to solve some of the problems.

Jan 1, 1980

By C. H. Riggs

This report describes the development, oil recovery, and potentialities of productive formations in the Hall-Gurney field, Russell County, Kans. It is presented as part of a general program to aid and promote increased recovery from petroleum reservoirs. The report is based on studies of well logs, drill cuttings, and oil-and water-production histories of individual wells and leases. The geological interpretations follow closely those in published literature with only slight local modifications. Oil and water analyses, made at a Bureau of Mines research center, were supplemented by many analyses obtained from oil-producing and service companies. The Hall-Gurney field, in south central Russell County, Kans., (fig. 1) was discovered in 1931 but was not developed extensively until 1941. By 1960 the rate of oil production from the field had declined to the extent that many wells were abandoned. In some areas natural productive forces have effected good recovery. However, in other areas inefficient waterflooding, both natural and accidental, has adversely affected recovery potentialities.

Jan 1, 1963

By Henry P. Cole

A series of studies are described that identify critical health and safety skills needed by underground coal miners for coping with mine emergencies. First aid and self-rescue and escape were selected as two broad performance domains that include many subordinate skills needed for preventing, recognizing, and coping with mine emergencies. The performance domains and their objectives were used to direct the development of simulation exercises that permit miners to experience mine emergencies in the safety of a training room. The exercises are based upon research with similar simulations for the training of flight crews and medical personnel in information gathering, judgment, and decision making skills. Exercise content is drawn from actual mine accident and disaster case studies. The exercises incorporate recent principles of cognitive psychology and instructional design. Initial studies in annual refresher training classes suggest the exercises are stimulating for miners and their instructors, easy to use and read, sufficiently complex and authentic to challenge experienced miners, and useful devices for both teaching and testing critical problem solving skills required for preventing and minimizing emergencies.

Jan 1, 1988

By R. F. Abernethy

Recent investigations in the United States and in other countries have produced considerable information on the nature and occurrence of minor elements in coal. The possibility of recovering certain elements, particularly germanium and uranium, from coal ash and other coal products has received considerable attention. Some flue dusts are potential sources of germanium, and certain lignite deposits are potential sources of uranium, but industrial recovery of these elements has been limited to small quantities for technical and economic reasons. Considering the large amount of coal mined annually, a small percentage of a rare element may have industrial significance if an economical method of recovery can be developed. In 1944 information on the occurrence of rare elements in coal was reviewed in Bureau of Mines Technical Paper 669 (46).3 This report is a revision of that paper with the view of summarizing published information available for United States coals, and pertinent information concerning coals of other countries. Selected references from the original paper are retained. New references do not include all preliminary reports when more permanent literature describing complete projects is available. Consequently, the list of references should not be considered complete.

Jan 1, 1963

By David A. Monaghan, Kenneth R. Maser, Adi R. Gurdar, D. Randolph Berry

8. Field Demonstration of the Remote Mine Sealing System in a Coal Mine 8. 1 Selection of Field Test Site Eastern Associated Coal Corporation (EACC) offered its Federal No. 1 coal mine in Grant Town, West Virginia as the site for field testing of the remote sealing system. The choice of Federal No. 1 mine was particularly appropriate as the first attempt at fire control by remote sealing was done in this mine in 1963. EACC provided the men and equipment required for much of the initial preparation. Considerable assistance, advice, and background on coal mining technology was given by Mr. William Laird, Vice President for Research and Development, EACC, and by Mr. Lawrence Jackson, Resident Engineer at the Federal No. 1 mine. District 3 USBM office, the West Virginia Bureau of Mines, the Technical Support Group of the USBM, and Local 4047 of the United Mine Workers of America also cooperated. 8.2 Preparation of Field Test Site 8.2. 1 Underground Site Preparation The underground site chosen for the field testing was in a non-working portion of the mine within a few hundred feet of the main haulage road, as shown in Figure 80. Known as "Seven Switch, " this area was a 20 minute walk or 5 minute "jeep" trip from the man-trip shaft. Ten years having passed since this area was actively worked, considerable effort was required for gob clearing, roof bolting, rock dusting, and rejuvenating the track from the haulage road to the test area. Three primary borehole locations were chosen for the test program. Borehole No. 1 was in a straight passageway

Jan 1, 1973

By Charles B. Kenahan

The chemical and galvanic corrosion properties of commercially pure titanium, a titanium-manganese alloy, a titanium-aluminum-tin alloy, 2 titanium-copper alloys, and 2 titanium-aluminum alloys were studied. Tests were conducted in synthetic ocean water, tapwater, 1-percent sodium hydroxide, 5-percent ferric chloride, and 5-percent ammonium sulfate solutions, various concentrations of sulfuric and hydro-chloric acids, and 1-percent oxalic acid. All tests were carried out at 35° or 60° C., with a flow of air or helium. Dissimilar metals involved in galvanic-couples experiments were aluminum, magnesium, and stainless steel. Electrode-potential measurements on single (uncoupled) specimens were also measured. Commercially pure titanium and the titanium-base alloys were generally quite similar in their resistance to corrosion, whether alone or in. contact with a dissimilar metal. Contact with the titanium metals caused aluminum and magnesium to corrode by galvanic action. Coupling with stainless steel in sulfuric acid solutions decreased the normal corrosion rate of the titanium metals. Contact with aluminum in air-aerated oxalic acid and 0.1N sulfuric acid solutions resulted in cathodic corrosion of titanium and the titanium-base alloys; however, there were a few exceptions. The copper alloys showed better corrosion characteristics than titanium in certain sulfuric acid solutions but were more susceptible to chemical attack in some hydrochloric acid solutions.

Jan 1, 1958