Search Documents

By Charles Dowding, Cathrine Aimone-Martin

This article summarizes an investigation of the structural response of a brick façade home in New Mexico. The subject Ricter residence was located some 1100 to 1400 ft away from an aggregate quarry, and was subjected to a maximum peak particle velocity and air blast over pressure of 0.29 ips and 122 dB, respectively. Superstructure (corner) and mid-wall responses to blasting and human induced activities were measured. An existing exterior crack in the brick work was instrumented to measure crack width response to blasting, human induced activities, and environmentally induced changes in temperature and humidity. Crack and structure response data were correlated with ground velocity and airblast excitations. Amplification of ground motions at the upper structure were calculated and compared with values for typical wood frame structures. The natural frequency and damping characteristics of the structure were determined to compare with measured amplification values. Wall strains produced by bending and inplane tension strains were computed from upper corner structure response and compared to failure strains for drywall and brick veneer. Calculated strains were found to be far lower than those required to crack brick and environmentally induced crack response was found to be far greater than that caused by blast induced ground motion or airblast overpressures

Jan 1, 2005

By Z X. Zhang

If the iron ore loss is 15% in the process of mining, the total iron ore loss in the world will be about 461 million tons, this is equal to the total production of 230 iron ore mines each of which produces 2 million-tons of iron ore per year. Based on a series of blast tests in the Malmberget mine, this paper shows that ore recovery can be markedly increased by improving blasting technology such as choosing a correct primer position and making use of shock wave collision. The paper further suggests that a high ore recovery can not only reduce natural resource loss and mining cost but also prolong the life of a mine. In addition, the paper shows an example of reducing blast-caused rock damage in the roofs and walls of underground drifts (tunnels) by using new blasting methods in the Malmberget mine. Finally, the paper shows how the Malmberget mine has successfully reduced the ground vibrations, without adversely affecting fragmentation and ore recovery in sublevel caving mining.

Jan 1, 2014

By Dennis J. Viscusi, James H. III Rowland, Lon D. Santis, Mark H. Weslowski

This paper describes the procedure for analysis of toxic fumes from the detonation of high explosives using the Large Chamber at the U.S. Bureau of Mines (USBM), Pittsburgh Research Center (PRC). This test is specified in 30 Code of Federal Regulations (CFR) Part 15.20 (g) as a requirement for the Mine Safety and Health Administration's (MSHA) approval of an explosive as permissible for use in underground coal mines. The Large Chamber replaced the Bichel gauge and CrawshawJones (C-J) apparatus in the 1989 revision of these regulations. To determine the safety of an explosive in terms of toxic gas production, the Large Chamber Test attempts to simulate mine conditions and miners' exposure to toxic gases from explosives.

Jan 1, 1995

By Thomas F. Mechtenberg, Michael S. Powell

In the past several years many coal operators and stone producers have reduced drilling and blasting cost by utilizing Bulk Emulsion/ANFO blends. For many operators the cost of equipment to handle blend products has been a major consideration in evaluating overall cost effectiveness of changing from packaged products or bulk ANFO to blends. This is especially true when the project length is short term or is uncertain.

Jan 1, 1990

By David Yanez

The hydroelectric project "El Cajón" is currently under construction in the state of Nayarit, on the Santiago River, in western Mexico. This project is comprised of a Concrete Face Rockfill Dam (CFRD) with a rockfill necessity of 10,5 million cubic meters and it reaches a height of 188 m. The generation equipment includes two turbines with a total installed capacity of 750 MW.

Jan 1, 2006

By Lawrie Logan, Mike Wiggin

This paper will be in two parts, a discussion of the benefits available from benefit sharing as a concept followed by an examination of how this approach was applied at Mesa J Mine and what improvements were made. The first part is an outline of the ways that both parties in a benefit sharing agreement can uncover additional wealth by bringing a new approach to the relationships between mine and supplier. The paper describes a partnering agreement recently established between Robe River Iron Associates (RRIA) and Dyno Nobel Asia Pacific Ltd (DNAP) to access the wealth locked up by the usual explosives supply contracts in Australia and elsewhere. The partners are acting cooperatively to maximise the benefits to both parties from optimising blasting practices at the Mesa J Iron Ore Mine in the Pilbara region of Western Australia.

Jan 1, 2001

By Travis A. Davidsavor, David A. Provost

A segment of high-pressure steel petroleum pipeline needed to be replaced on a hillside and beneath a waterway within an existing right-of-way containing multiple petroleum pipelines. The pipeline replacement required excavation of sedimentary rock to allow placement of the new pipe. As a result of an existing right-of-way limitation, steep slopes, and hard rock, blasting would be required as close as 7.8 meters (25 feet) from two operating pipelines.

Feb 1, 2020

By Paul Miller, Rene Laprade

Does a 76 mm Ø hole drilled over 45 m deep remain straight? This is the question asked by the Engineering department at Placer Dome's Dome Mine in Timmins, Ontario before they could lay out the initiation sequence in a long-hole production stope. Everyone realized that the holes would wander over such great depths, but it was important to know where they went.

Jan 1, 1998

By M Lemieux, R Mason

The SABREX blast modeling program was introduced to I.O.C.C.'s Carol Lake Iron Ore Project in December 1987. As part of CIL's Technical Services, SABREX was used to implement an optimization program designed to analyze and introduce various grades of MAGNAFRAC at a constant pattern while maintaining acceptable blast results.

Jan 1, 1989

By Paul Worsey, Yasutaka Dote

The choreography of large fireworks displays dictates electric initiation for precise timing. It has been common practice to pre-squib products before transportation for reducing set up time. A number of fatal accidents transferring pre-squibbed product during transportation suggests that there is a problem with impact sensitivity. The aim of this paper is to quantify the impact sensitivity of the various configurations of initiating materials used in display fireworks.

Jan 1, 2009

By J. A. Sanchidrián, P. Segarra, S. Gómez

Blasting is a common activity in mining that can cause significant damage in the remaining rock mass. The most commonly used method for predicting vibrations is the Swedish or Holmberg-Persson approach. It is a simple and fast method that uses empirical formulation to estimate the vibration levels based on the explosive charge weight, distance to the source, and other parameters. However, it has limited accuracy and does not consider the effect of free surfaces or other boundary conditions. On the other hand, recently developed methods as the full-field solution (FFS) can provide more accurate predictions of vibrations due to excitations provoked by cylindrical columns of explosive, but the inclusion of free surfaces in analytical methods is a challenging problem. This paper presents a new approach that includes free surfaces in the FFS to predict vibrations analytically in the near-field. The main obstacle to including free surfaces in the FFS was the belief that the solution was non-decoupleable in P- and SV-waves separately. The Heelan's approach was previously used to decouple them, but it only provides valid radiation patterns in the far-field and does not account for intrinsic attenuation. In this paper, we address this problem successfully, allowing for the inclusion of free surfaces in the FFS.

Jan 1, 2024

By Jeff Hermanson

Every construction project has site specific problems that need to be dealt with. These problems may be created by the geology, location, weather, time constraints, etc. Once these problems have been solved their solution often can be transferred to other similar construction sites. The Crazy Horse Memorial project is no exception.

Jan 1, 1996

Previous approaches to pre-split blasting theory have tended to concentrate on the mathematics of dynamic stress wave interaction, whilst only recognizing some interaction with quasi-static stresses induced by expanding gases in the boreholes. However the decoupling used in pre-splitting is specifically designed to reduce dynamic effects to a level that a small degree of radial fracturing is created around the borehole which is emphasized and extended by quasi-static gas effects. It can thus be argued that the process has more in common with hydrofracture than with more conventional use of explosives.

Jan 1, 1984

By Ravi Sahu, Ankit Jha, Sudarshan Rajagopal, Purushotham Tukkaraja

Geologic structures are one of the crucial parameters in blast design. Structural geology and rock properties influence drilling patterns, blast layout, and initiation systems. A comprehensive understanding of structural characteristics is essential to achieve the desired blasting objectives. This paper aims to identify geologic features in a bench using images obtained from the drone.

Feb 1, 2020

By Jennifer Williams, Donald J. Berger

Originally built between 1913 and 1916, the Ashton Dam & Hydroelectric Facility has experienced various seepage and piping incidents since completion. Ashton Dam is located within 15 miles (24 km) of the historical Teton Dam failure site and about 2.3 miles (3.7 km) west of Ashton, Idaho. Numerous repairs conducted over the years ranged from filling sinkholes on the crest of the dam to placement of rockfill on the upstream slope to improve seismic stability. In addition, the existing low level outlet works was grouted full and abandoned in 1991 due to significant vibrations induced on the dam during its operation.

Jan 1, 2014

By Jhon Silva-Castro, Russell Lamont

Understanding the behavior of materials subjected to high strain rate conditions is of fundamental importance to the mining industry. Several stages of the mining process involve high speed loading rates including blasting, scraping, comminution, etc. Technical comprehension of how rocks deform, fracture, and fail under these loads is a fundamental first step required prior to any serious attempts at optimization of the energy utilized for pertinent activities in the mining process. A Split-Hopkinson Pressure Bar (SHPB) was designed and constructed at the University of Kentucky to study the dynamic properties of various types of rocks.

Jan 1, 2017

By T Davids, O J. Jordaan, M D. J Bonneau

As in most other parts of the world, the surface coal mining industry in South Africa is introducing emulsion explosives as the primary bulk blasting agent for use in wet borehole conditions where AN/FO cannot be used. Most of the emulsion products presently in use are gassed to provide sensitivity. The intimate mix between the fuel and oxidizer in the emulsion has been shown to produce a highly efficient explosive. However, a major difference between emulsion and the previous slurry products is its relatively low physical strength. This prompted Rand Mines' Duvha Opencast Mine, a major South African Escom power colliery, to conduct test work to illustrate the effect of emulsion physical consistency on blasthole loading. This paper presents the results of test work conducted at Duvha to investigate the problems associated with loading both AN/FO and emulsion in water filled holes, stemming emulsion holes, and in particular, to illustrate the difficulty in correctly introducing a stemming deck into the emulsion column. Time dependent behavior of the loaded emulsion holes is investigated. Velocity of detonation measurements for freshly manufactured emulsion, and for emulsion after loading through water with sleep times of up to 10 days, are presented.

Jan 1, 1987

Prediction of fragmentation in Taconite Mining is an important aid to blasting engineers. A simple theory relates the intensity of radial fracture per unit length to distance from the borehole, from which a power law for mass fraction passing versus size is derived. For the lower end of the size distribution, the equation agrees well with several published examples of fragmentation from sieving of full scale blasts. Large size fragments arise from interaction of fractures from neighboring holes and pre-existing joints. Analysis of two assumptions regarding radial fracture interaction shows that complex fragmentation distributions can arise from the simple mechanisms proposed. Measured fragmentation falls between the two extremes calculated.

Jan 1, 1996

By Jorge Flores, Benjamin Cebrian

Blast Optimization at a high altitude mine operation involves not only the selection of the right drilling designs and explosives but also the circumstances of operators working at low oxygen levels and low temperatures.

Jan 1, 2015

By V R. Sastry, D P. Singh, N R. Thote

Rock parameters which are uncontrollable impose restrictions on the procurement of desirable fragmentation. Blast design parameters which are controllable prove to be important tool in blasting operations. An attempt was made by the authors to investigate parameters which causes big oversize boulders in overburden blasting. A case study of coal mine is discussed in this paper.

Jan 1, 1995