Search Documents

By Ken C. Pruss

Seismic studies have proven that the frequency with which shock or vibration waves are reacting on a structure, in correlation with the amplitude of those waves, has a definite affect of structural damage. Different structures will react to different frequencies. In the past few years, some major coal producers in the midwest United States have shown that with the use of highly accurate detonators and exotic timing patterns they have effectively been able to adjust frequencies and this has enabled the operators to continue their excavation of overburden in environmentally sensitive areas.

Jan 1, 1989

Hello, everyone. Way back in 1965, Devine and others at the US Bureau of Mines showed that a presplit fracture plane did not affect vibration levels transmitted across the plane (RI 6695).

Jan 1, 2010

By Sehoon Lee, Duhwoe Jung, Eunsu Cha, Kyeonghwan Jeong

This case study presents the effectiveness of underground rock blasting to facilitate the trench cut in the hard rock layer using a conventional trench cutter for the construction of a diaphragm wall. Rock blastings are pre-performed up to the scheduled depth and then the fragmented rocks can be easily cut using a conventional trench cutter. Two trial underground rock blastings have been performed and the effectiveness of pre-blasting is presented in terms of a cutting rate, a loss of cutter heads and an amount of overbreak. Based on the results obtained from the trial underground rock blastings, the following conclusions can be appropriate: 1) A pre-blasting of hard rock layer located in depth can help to overcome the limitation of the trench cut using a conventional trench cutter. If the hard rock layer is fragmented after blasting, the fragmented rocks can be easily cut using a conventional trench cutter, 2) The speed of cutting works was accelerated and the loss of cutter heads was significantly reduced in the sections where the blastings were applied prior to cutting. 3) The amount of overbreak, expressed in terms of the amount of poured concrete, can be reduced to some extent. However, the location of blast holes in the trench can also contribute to the amount of overbreak. The closer the location of blast holes to the edge of the trench, the more extensive fractured and cracked zone can be formed on the face of the trench. This can increase the amount of overbreak if the trench is left empty for a while.

Jan 1, 2000

By Thomas P. Mahoney

Phelps Dodge Corporation's Tyrone Mine is a large open pit copper operation located in the southwestern corner of New Mexico. The Tyrone concentrator processes approximately 50,000 tons per day of copper ore. The waste ratio for this operation is 3:1; e.g., for every one ton of ore mined, three tons of waste material are also removed. This results in a mining rate of about 200,000 tons per day.

Jan 1, 1986

By Thomas P. Dowling

Since the 1950's, blasting practices have undergone many revolutionary changes. Some of the more radical departures have involved, in addition to high speed drilling equipment, a myriad of new explosives, blasting agents, boosters, initiators, initiating systems and delay devices. The introduction of ANFO in the mid 1950's as a blasting agent seems to have instigated a trend toward the development and use of less sensitive blasting agents. The evolution of slurries or water gels has produced dense, high strength, water resistant products which has further promoted this trend away from the more sensitive, conventional explosives.

Jan 1, 1975

By Jeff Wachendorf

Due to the competitive nature of the coal industry we are constantly challenged to reduce costs associated with day to day operations. Every facet of the mining operation is scrutinized for cost reduction and possible efficiency increases. This paper will discuss the pros and cons of two different blasting methods. Buffer blasting has been an institution for many years at Spring Creek Coal and very successful in its application. Cast blasting arrived on a trial basis in 1998 and has produced very encouraging results. This paper will describe the design, drilling, and blasting methods currently used, and a comparison of these two methods.

Jan 1, 2001

By Steve Dillingham

In recent years, there has been a trend toward increasingly demanding blasting standards being enacted by local and regional regulatory authorities. The objective of this paper is to alert blasters of the difficulties that are created for blasting projects as a result of these restrictions, as well as the steps that can be taken to minimize future conflicts.

Jan 1, 1995

By Melvin A. Sannes

The explosives industry is recognized as one of the most dangerous occupations in the world, yet it is rare to see actual training procedures. As our industry becomes increasingly technical, it is imperative that we train the personnel in OUI industry properly.

Jan 1, 1999

By Dale S. Preece, Stephen H. Chung

"In bench blasting, the distribution of loaded explosives with respect to the burden rock has strong effects on digging especially at the toe area. Blast design often focuses on other results such as percent-cast or fragmentation, sometimes leaving a diggability problem at the toe of the blast that is not discovered until excavation. A method for assessing the influence of blast design on diggability has been developed. This method relates the kinetic energy and rock displacement experienced by the material in the muckpile to its diggability. Simulation of the blast along with the calculation of kinetic energy and diggability is done with the discrete element computer program DMC_BLAST(DMC: Distinct Motion Code)."

Jan 1, 1999

By Daniel Moroz

This paper will provide an informative overview of the types of explosives and the various methods employed to control avalanches within the boundaries of major ski resorts.

Jan 1, 1991

By K A. Broadhurst

Over the years International Standards have produced and are continuing to work on documents related to damage from blasting and human exposure to whole-body mechanical vibration and repeated shock.

Jan 1, 1988

By Calvin J. Konya

Precision Blasting has designed easy to use, yet, highly powerful databases for storage and retrieval of blasting data. Three different Databases are available for blasting data management. The Vibration Data Management is a complete vibration record keeping system. The Blasting Data Management will record the information from the blasting report as well as the vibration data. The Explosives Inventory Control makes the control of explosives and initiators quick and easy.

Jan 1, 1991

By Robert C. Friend

On-the-job and "hands-on" training programs which attempt to train newcomers to blasting with instructors whose only qualification is their experience can easily miss the boat. Organized training programs which utilize competent instructors and a well developed format are necessary if we wish to provide a meaningful program of instruction, But, let's not go overboard and attempt to provide a level of training which goes far beyond the scope of the worker's duties and responsibilities, and "need to know",

Jan 1, 1980

By Robert C. Fouchard, Gordon Chalmers, David E. G. Jones, Ivana Alilovic, Phillip D. Lightfoot

There have been numerous international instances over the last several years in which pumping emulsion explosives has resulted in accidents, apparently as a result of increased thermal sensitivity under these conditions. The key questions for the explosive industry are (1) what are the parameters that influence the sensitivity of emulsion explosives and, (2) how do these various parameters interact. To address the sensitivity of emulsion explosives to various parameters, a study was undertaken using an accelerating rate calorimeter (ARC) and a heat flux calorimeter (HFC). The effects ofthe addition of ammonium nitrate (AN) prills and different grades of aluminum (Al) on the thermal behaviour of emulsion explosives were determined. Additionally, changes in pressure, atmosphere (inert or oxidizing) and sample vessel material were assessed for their impact on thermal sensitivity. Addition of AN prills, fine granular Al or atomized Al did not affect the onset temperature for exothermic decomposition, so that the maximum “safe” temperatures for emulsions containing these additives will be similar. There were differences in the rates of self heating, however: AN prills decreased the rate of self heating, whereas atomized Al increased it. The emulsion formulations containing atomized Al produced small holes in titanium vessels. This phenomenon did not occur in Hastelloy C vessels, providing a reminder that materials of construction need to be carefully considered for equipment used to manufacture or handle emulsion explosives.. Both ARC and HFC experiments gave lower onset temperatures in air than in argon. We attribute this to oxidation of the oil phase by air. This result is significant for dry-running pumping conditions, where emulsion is heated in the presence of excess air.

Jan 1, 2000

By Dale Preece, Stephen Chung, Richard Jensen

DMCBLAST_3D is a three-dimensional extension of the proven two-dimensional rock blast modeling code, DMCBLAST. DMCBLAST has been under development since 1987 and has successfully predicted the physics, mechanisms and results of a number of different types of rock blasting including, coal mine bench blasting, mineral mine choke blasting and underground stope blasting. Substantial effort has gone into the qualification and verification of DMCBLAST by comparing computer code predictions with real blasts in the field. Comparison with field data has also provided significant guidance to the development of the code.

Jan 1, 2001

By D Linn Coursen

In the proposed method, the charges are elongated and arranged in one or more arrays. The orientation of each charge in an array, its velocity of propagation of explosion, and the velocity of propagation of vibration in the formation are such that, at an outlying location where vibration is to be reduced, the onset of vibration from explosion of the first negligibly small increment of each charge arrives a finite time before that from explosion of the last negligibly small increment of that charge. The charges of each array are fired in accurately-timed sequence, with the times between initiations chosen so that, at the outlying location, the onset of vibration from explosion of the last small increment of each charge, except the last charge, arrives a negligibly small increment of time before the onset of vibration from explosion of the first negligibly small increment of the succeeding charge. With such timing, vibration may be reduced at the widest range of locations by tilting the boreholes so that the terminal end of each charge is directly above or below the terminal end of the succeeding charge.

Jan 1, 1995

By William F. Skully

An effective explosives storage program involves selection of a storage site, checking zoning and special permit requirements, acquisition of the storage site land, determining correct layout for required storage units, selection of storage units, construction of storage area, obtaining licenses and permits, and storage site operation.

Jan 1, 1976

By Roger N. Prescott

The Bureau of Alcohol, Tobacco and Firearms (BATF) is sponsoring legislation requiring the addition of identification taggants to commercial explosives. These are plastic particles with color coded layers that theoretically can be used to identify the explosive by date shift code.

Jan 1, 1980

By Fred C. Drury

The Explosives Engineer's concern for personnel training in the safe, efficient and effective use of explosives materials has grown in recent years. Available training options have also grown. Today's options include off-site training seminars and in-house training departments, both of which represent significant cost to the smaller producer.

Jan 1, 1981

By Donald H. Matthews

The Society of Explosives Engineers is an international organization of over four hundred members involved in the explosives industry, with most members being active in the United States. The regulations imposed by regulatory agencies on the explosives industry have drastic effects far beyond the industry. Since explosives are used in mining, manufacturing, construction, entertainment, and art, all phases of man's activities, including fundamental needs for survival, are affected by how efficient the industry uses explosives. We, as members of SEE, must be sincerely concerned with both the quantity and quality of government regulation, and this paper spells out some of the problems caused by regulations and offers a solution.

Jan 1, 1980