Search Documents

By Christopher Robben, Alexander Mosser

"X-ray transmission (XRT) sorting has been introduced into the minerals industry in 2006 and has found various applications in diamonds, industrial minerals and metal ore processing since. The technology offers planar projections of the atomic density of single particles similar to the principle known from airport scanners, but being capable of treating up to 150tph per metre working width. In 2010, a pilot operation using a belt-type sensor-based sorter went into production at the Mittersill mine to treat the fraction 16-28mm. After an optimisation phase, the results were superseding expectations and therefore in 2012 a bigger production plant was set up. Two XRT-based sorters are parallel in operation since. One is treating the fine fraction 16-30mm while the other one is treating the coarser fraction 30-60mm after the secondary crushing stage. The XRT sorters are operated with the objective to reject barren waste before it enters the mill and flotation plant. 105,000tpa of waste material are rejected per year and can be sold as aggregate for road construction. This means that about 22% of the run-of-mine ore are rejected at an early stage with a waste reject grade lower than 0.03wt%WO3. The installation has not only led to lower specific operating costs but also led to reduced tailings disposal in an environmentally sensitive area. This allows the mine to reduce its headgrade which allows for a longer mine life. Alternatively it is possible to produce more tungsten concentrate, which is delivered to the smelter. This article will introduce the technological principle of XRT-based sorting and will discuss the flow-sheet of the Mittersill mine. Experiences that have led to the current plant design are described as well as the impact it has on the operation."

Jan 1, 2014

By T. Bhambhani, O. Yavuzkan, D. R. Nagaraj

"The recovery of oxide Cu minerals by flotation is a longstanding challenge in the minerals industry, especially for high acid-consuming ores which would not be economical for direct acid leaching. Sulfidization (often using controlled potential sulfidization or CPS) using NaSH (or Na2S) followed by flotation using traditional sulfide collectors is the widely used technique. CPS has certain limitations: a) inability to recover certain oxide Cu minerals because they are refractory to sulfidization, b) high consumption of NaSH (or Na2S), and c) potential health and safety hazards associated with NaSH (and Na2S). Flotation of oxide copper minerals using alkyl hydroxamate (AHX) collector has been studied extensively. Investigations using single minerals and laboratory ore flotation have been conducted in the past to demonstrate the efficacy of alkyl hydroxamates. The technology has been used intermittently in plants. One of the main challenges in plant use has been quantifying the true potential for alkyl hydroxamates for recovery of various oxide Cu species in complex and variable ore systems and identifying the most suitable conditions for optimal use. Quantitative mineralogical analysis using QEMSCAN was used in this study to characterize flotation products lab flotation samples. Analysis of concentrates and tails from hydroxamate flotation and CPS flotation stages demonstrated that certain oxide Cu minerals respond exclusively to alkyl hydroxamates and not to CPS. The hierarchy of interaction of AHX with the various oxide Cu minerals could be inferred from these studies. Finally, these studies also allowed quantification of a group of minerals species, which (erroneously) report as part of the Acid-Soluble Cu [ASCu] but cannot be recovered by flotation, thereby facilitating an estimation of the true recovery potential for alkyl hydroxamate.INTRODUCTIONCopper that is economically recoverable occurs in three major types of ores, which are defined by the modal mineralogy of Cu. For sulfide ores, Cu occurs as sulfide minerals and is satisfactorily recovered by flotation using sulfide collectors. Non-sulfide ores, which contain Cu in the form of oxides, phosphates, carbonates and silicates, described in the industry as “oxide” ores (or ores containing “acid-soluble” Cu or ASCu), are currently treated using hydrometallurgy, which involves leaching with dilute sulfuric acid followed by solvent extraction and electrowinning, unless the ores contain acid consuming gangue minerals such as dolomite. For mixed sulfide-oxide ores (i.e. containing both sulfide and oxide Cu minerals) that do not contain acid consuming gangue minerals, Cu values are easily recovered by flotation of sulfide Cu minerals followed by leaching of oxides (only when a leach plant is available). However, when the ore contains acid consuming gangue minerals flotation is required to recover both sulfide and oxide Cu minerals."

Jan 1, 2018

By Urs Peuker, Thomas Mütze, Thomas Leißner, Inga Osbahr

"Mining in the Ore Mountains (Germany) has taken place for hundreds of years and in several stages. Each stage produced its typical tailing. According to the former state of the art of the processing much valuables could not be extracted. This was caused by complex interlocking of the minerals, low grades, or by upgrading processes not sensitive enough for small particle sizes. Thus the processing of these fractions was uneconomically. Modern technical possibilities and rising metal prices bring these tailings disposals into focus for the processing of strategic metals. Mining disposals can be classified in heaps with coarse, low grade rock, which did not undergo a processing, slags and fly ash from smelting, and tailing disposals from mineral processing. The latter is under investigation to integrate them into a geographic information system. The mineral processing of the material will be part of the database besides information about geographic location, structure, amount of valuables, and details of ownership of the heap. The tailings disposals are composed of coarse, low grade, interlocked particles from density separation processes, medium size particles, which are tailings from flotation, and fines with liberated valuables, which did not undergo flotation. Therefore mineral processing of these disposals comprises the separation of liberated gangue by classification, beneficiation of locked valuables with density separation, liberation of valuables by grinding, and beneficiation of liberated valuables with flotation. The presented work shows the results concerning the composition of one exemplary heap and results of the classification as well as of the preconcentration tests achieved with material from this heap."

Jan 1, 2014

By Markus A. Reuter, Yongxiang Yang, Jim R. Post

In the upper part of an iron making blast furnace, sinter, coke and pellets are charged. While descending, the burden is heated and the iron oxides are reduced by the rising gases. The iron oxides start to soften and eventually melt. The melt and the remaining coke collect in the lower part of the blast furnace: the hearth. The remaining coke forms a porous bed: the dead man (see Figure 2). The melt flow through the dead man can affect substantially the hearth lining life, the furnace productivity and product (i.e. hot metal) quality. Physical characteristics like porosity and particle size distribution of the porous coke bed play a critical role. Because of the distributed nature of the coke properties, the bed packing structure and porosity will not be constant.

Jan 1, 2003

By A. Mainza, H. Hill, L. Bbosa

"The main objective of ore breakage characterization is to quantify the relationship between the energy supplied for breakage and the size of the resultant progeny. In this study, the ore breakage characteristics of drill core particles and crushed particles were compared. Single impact breakage tests were conducted on a basalt ore sample using the JK rotary breakage tester. The size-dependent model by Shi and Kojovic was used to fit the breakage data because the effect of initial particle size is accounted for in the model. It was found that crushed particles consistently gave a higher degree of brokenness than drill core particles and the differences were attributed to the internal structure of the particle. Drill core particles contain a lower crack density (paths of weakness) than crushed particles which have been pre-weakened during the crushing process. An increase in crack density is directly related to a decrease in the minimum threshold energy. Upon application of a stressing force above the stress threshold, particles with a higher crack density will fracture more easily because of a higher rate of crack propagation due the numerous paths of weakness available. It was therefore concluded that under the same conditions, drill core particles are more competent than crushed particles. INTRODUCTION Comminution devices have commonly been reported as being the largest energy consumers in mineral processing circuits (Napier-Munn, 2015). Cleary (1998) reported that the inefficiency of comminution devices is a result of less than 5% of the supplied energy being utilized for breakage, with the majority being expended as heat and noise. With steadily declining fossil fuel supplies and a looming global energy crisis, the mineral processing industry has increased its focus on energy reduction measures. Ore breakage characterization plays a critical role in the design and optimization of comminution circuits (Tavares and King, 1998). The main objective of ore breakage characterization is to empirically quantify the relationship between the energy supplied for breakage (specific input energy) and the size of the resultant progeny through laboratory particle breakage tests (Napier-Munn, 1996). Commonly used laboratory breakage devices include the Drop Weight Tester (DWT), Split Hopkinson Pressure Bar (SHPB) and more recently, the JK Rotary Breakage Tester (JKRBT). Typically, a standard single impact breakage test procedure consists of a matrix of experiments on particles in four to five narrow size fractions each tested at low, medium and high energy levels. The resultant progeny of each test is sized to obtain a particle size distribution (PSD) from which the degree of breakage, usually in the form of a t10 value (percentage of the progeny material that passes 1/10 of the feed size) can be obtained for each size fraction and energy level (Napier-Munn, 1996)."

Jan 1, 2018

By X. Xu

This paper presents the research on comprehensive recovery of copper, gold, silver and iron from tailings from high-intensity magnetic separation in Tonglushan Mine. By comparison of experimental results of three flowsheets?regrinding of tailings-conventional sulphidizing flotation, water heating enhanced sulphidizing flotation and acid leaching-sulphidizing precipitation flotation, it is concluded that regrinding of tailings-conventional sulphidizing flotation flowsheet has the best economical and technical performance and practicability. Regrinding and using the mixture of sodium hydroxamate and sodium xanthate are two of the notable technical characteristics of this best flowsheet. The system for comprehensive recovery of tailings has been put into production. It not only can recover the valuable minerals from tailings in Tonglushan Mine, but also can reduce the environmental pollution, resulting great economic and social benefit.

Jan 1, 2014

By P. Matias

The study involved two projects that will produce copper concentrate and may have their operations integrated. Transport by trucks, conveyor belt, and the equipment called RopeCon were evaluated as options for the ore transport between the sites. A rainforest stretch, that Vale S.A. demands to preserve, is situated between the projects. It was suggested to further review RopeCon because it presents minimal interactions with the environment. To design the preliminary system layout, a research was done on the rainforest cover height data, but the information found was scarce and imprecise. For preserving the local forest, the use of this data would conduct to the oversizing of RopeCon towers and, consequently, overestimation of its costs. For the acquisition of reliable information, a method was developed using local data acquired through airborne laser survey. The volume between the digital surface and terrain models was calculated to generate a surface representing the forest cover height. It was revealed, by plotting the points obtained from this surface, that 85% of the vegetation is below 25 m. This height is suggested to review the preliminary project with a more accurate design of the equipment towers, thus reducing its costs estimates. The method permits the precise location of the large trees, making easier to find a pathway, for linear-shaped facilities, that would minimize the creation of vegetation-free zones as a measure to protect equipments against falling trees and forest fires. Keywords: forest cover, mining projects facilities, digital models, airborne laser survey

Sep 1, 2012

By D. Saramak

The comminution technology based on High-Pressure Grinding Rolls presses (HPGR) application is currently one of the most efficient methods of hard ore comminution from the scope of the energy consumption and the development of industrial HPGR applications in ore preparation circuits is presently the world trend. However, even though the technology is already in use in many countries, which are the leaders in application of modern mining technology, there is still lack of base investigations over the HPGR performance. Throughput and energetic models of HPGR performance are quite well developed, but technological models predicting the comminution effects still needs an in-depth research. In the paper authors present the method of modeling of HPGR products? particle size distribution with using of suitable mathematical models. A basis of the HPGR performance assessment and HPGR-based crushing circuits design is a product?s particle size distribution. In order to precisely determine the particle size distribution of a HPGR product, parameters of product?s particle size distributions should be conditional on the main technical parameters of the roller press like operating pressure and the speed of rolls. The most accurate approximation of a distribution of size particle d appeared the Weibull?s truncated distribution and it is possible to obtain significant relationships between the approximation formula and the value of operating pressure, or feed characteristics. It makes possible a determination of mass recoveries of the product?s respective size fractions and the productivity planning. Instead of pressure (P), the other HPGR operating parameters can be applied, but the P value appears to produce the most relevant relationship. Keywords: HPGR, comminution, particle size distribution, ore processing

Sep 1, 2012

By H. J. Cao

Valuable elements could be extracted by microorganism ferment fluid from bauxite, which mainly due to bacteria acid namely organic acid. And after leaching, reclaiming the remainder organic acid in leaching solution was an important procedure for bauxite leaching process. the re-searching status about organic acid reclaiming process from bauxite ore bioleaching solution was summarized. Common processes for recycling organic acid from bauxite bioleaching solution in this period and their advantages and disadvantages, research aspects which need being confirmed for the future were Indicated

Jan 1, 2014

By G. Semenchenko

Heterotrophic microorganisms Pseudomonas aureofaciens, microscopic fungi Fusarium sp. and their combinations with some chemical substances were used for gold leaching from refractory ore and flotation concentrateof Akbakaj deposit. All biological additives raised the speed of noble metals dissolution. The best results of gold extraction from ore were in the presence of bacteria or their associations with other solvents and from flotation concentrate in the presence of fungus - 30 % of additional amount of gold. The maximum extraction of gold speed value was during the first 8 hours of process. The electronic-microscopic researches of the ore samples showed almost complete decay of pyrite and arsenopyrite under bacteria influence whereas at chemical leaching most of these minerals stayed uncrushed. The presence of microscopic fungi in flotation concentrate during leaching provided full distraction of pyrite, but some crystals of antimony and arsenopyrite were undestroyed. During cyanide leaching of flotation concentrate there were accumulation of antimony and incomplete pyrite decomposition. Keywords: gold bioleaching, bacteria, fungi, complex solution

Sep 1, 2012

By B. A. Kutlin, S. A. Ropeyko, N. A. Yurlova

"The aim of NPO RIVS research and practice activities is to minimize impact of the mineral processing plants (MPP) on environment by using new concentration methods, high-technology equipment, implementation of engineering solutions directed to reduce emission of polluting substances (PS) into atmosphere, application of low-waste technologies, decrease of water withdrawal from a surface water or groundwater source for process needs. In our studies environmental safety of mineral flotation is provided through technologies using highly selective chemicals, that leads not only to reducing reagent consumption, and production of saleable products of high content of extracted minerals, but also to reducing pollutant emissions, decreasing supply of surfactants (SAA) in natural geosystems, primarily, in ground and surface waters. Decrease of water withdrawal from a surface water or groundwater sources for process needs can be achieved by using closed circuits and waste water treatment for further use in process operations, recycled water conditioning to obtain optimum quality parameters for process operations of concentration. Concentration in water (wet processing), tailings dewatering and semidry and dry (filtration cake) stockpiling in tailing ponds, efficient dust-collecting systems contribute to pollutant emission reduction. Use of mineral wastes – concentration tailings as a source of valued components, facilitates efficient use of natural resources and reduces wastes and its impact on natural ecosystems due to smaller areas of damaged lands during waste products disposal. Process and engineering solutions of NPO RIVS that allow diminishing impact of MPP on natural environment (NE) have been implemented in mining and processing complexes of Russia, Kazakhstan, Ukraine, Kirghizia and Mongolia. Compliance with environmental safety requirements contributes to enhancement of mineral processing and sustainable mineral development.INTRODUCTION Mining and processing complexes have a significant impact on environment as a result of extraction and recovery of mineral resources, landscape changes, waste disposal and, as a consequence, pollution of soils, surface and underground water sources. Therefore, the aim of the operation of the mineral processing enterprises in its research and practical activities is to reduce impact on environment due to new beneficiation technologies, high-technology equipment, implementation of engineering solutions directed to reduce emissions of polluting substances (PS) into atmosphere, use of low-waste technologies, decrease of water withdrawal from a surface water or groundwater source for process needs. Compliance with the requirements of environmental safety encourages advancement of mineral processing technologies and sustainable mineral development. Concentration in water, tailings dewatering and semidry and dry (filtration cake) stockpiling in tailing ponds, efficient dust-collecting systems contribute to pollutant emission reduction. Use of mineral wastes – concentration tailings as a source of valued components, facilitates efficient use of natural resources and minimizes waste formation and its impact on natural ecosystems due to reduction of damaged land areas during waste disposal."

Jan 1, 2018

Much has been published in recent years on the challenges facing the engineer of the 21st century and the consequent challenges facing the education providers and industry. The world is changing rapidly on the social, economic, political, technical and environmental fronts and our metallurgists/mineral processing engineers of the future will arguably need to have a different set of skills than those which were traditionally regarded as adequate during the latter half of the 20th century. This paper attempts to explore some of these issues and their ramifications.

Jan 1, 2014

By G. Aguilera

It is known that an addition of rigid particles into a fluid medium changes the flow field. Therefore, the rheological behavior of suspensions will be hardly Newtonian, such as their continuum phase. This phenomena was studied by Einstein in 1906 (Einstein, 1956) for the single case of spherical particles in a continuum liquid of a very dilute suspension. The final analysis applied for suspensions was derived from the evaluation of the behavior of ideal gases, finding a simple expression for the viscosity of the dispersion. All the following works about the hydrodynamics of suspensions at low and high solid contents was based in the Einstein´s model. For clay minerals suspensions where the physical and chemical properties of the particles are complex, it was found that the Einstein´s model is not a good approximation, even so for the most dilute dispersions. The present paper shows a new approximation that describes the non-Newtonian behavior of the suspensions of clays, and the attempt of understand how the different fine sizes, shapes and physico-chemical properties of clay particle surfaces give specific characteristics of plasticity, viscosity or visco elasticity to suspensions. Keywords: viscosity, clay minerals, einstein´s model, dilute suspensions

Sep 1, 2012

By Caitlin Rogers

The environmental and economic sustainability of froth flotation is dependent on effective management, which in turn improves the performance of a concentrator. In economic terms this means improved recovery of valuable minerals, in environmental terms this means effective management of acid generating tailings. Three indicators were selected to measure the performance of an integrated flotation system. The system consists of two stages of flotation; valuable mineral flotation followed by environmental desulfurisation by froth flotation. The suitable indicators were selected based on their fulfilment of four attributes. An attribute is a desired aspect of an indicator. The four attributes were: comprehensive, relevant, sensitive and quantitative. Two environmental indicators and one economic indicator were selected. They represent revenue generation from valuable minerals and environmental cost of management. The suitability of the selected indicators was shown using illustrative scenarios.

Jan 1, 2014

By Dave Deglon

The Western Cape Mineral Processing Facility (WCMPF) is a collaborative educational initiative between the Departments of Chemical Engineering of the University of Cape Town, the University of Stellenbosch and the Cape Technikon. The WCMPF was established in 1989 with the aim of improving mineral processing education in the Western Cape. Since its inception the WCMPF has had a number of successes in this area, especially in improving the quality of mineral processing practical training. In addition, the WCMPF has played an important role in promoting liaison and interaction between tertiary educational institutions teaching mineral processing in the Western Cape. Over the past decade the WCMPF has played a key role in the education of over five hundred mineral processing graduates and diplomates. This paper presents an overview of the activities of the WCMPF and attempts to encapsulate the ‘lessons learned’ from over a decade of successful functioning as a collaborative educational initiative in mineral processing.

Jan 1, 2003

The flotation efficiency of magnetic concentrate of the Anhui hematite ore, which includes a great quantity of iron-bearing silicates, has been studied through reverse flotation test with a new type of collector Fly-102. The results indicate that collector Fly-102 has a strong adaptability to the variation of temperature, when the flotation temperature is in the range of 10? to 35?, using collector Fly-102 can obtain good flotation indexes. Collector Fly-102 has a strong adaptability to the variation of the slime contents and grades of the flotation samples. When the content of slime and the grade of the flotation feeds are 30% and 55.63% respectively, under the condition that the temperature is 15?, the open circuit flotation test was carried out with collector Fly-102. After one-stage roughing, one-stage cleaning and two-stage scavenging, a better result is got, the grade of iron concentrate reaches 67.12%, and the recovery of iron concentrate comes up to 84.15%.

Sep 1, 2012

By E. Kusaka, M. EL Salmawy

"The electrokinetic behavior of EL Maghara coal has been investigated in the presence of nonyl and octyl nonionic surfactants containing polyethoxy of different sizes with trade names of Triton-X100 (TX-100), Triton-X 705 (TX-705), Triton WR-1339 (TWR-1339) and Brij 58. The electrokinetic behavior was determined by zeta potential measurements. Zeta potential measurements were conducted by Laser-Doppler electrophoresis technique using zetamaster. The results show that the zeta potential of Egyptian coal varies with pH value, the hydrocarbon chain and number of ethoxy groups in the hydrophilic group of the surfactant. It was found that the polymeric surfactants reduce the negative values of zeta potential of coal. The shift of PZC of coal upon deashing appears to be closely relevant to silicate mineral removal."

Jan 1, 2014

By A. V. Kozub, D. O. Sharkovsky, R. I. Ismagilov

"Due to complex mineral composition and fine ingrained nature concentration of iron ores deposited in Mikhailovskoye mine field requires application of wet magnetic separation to produce 65–66% Fetotal and 8.2–8.6 %SiO2, concentrate with 90–94% of material being –0.044micron grain size. Higher specific consumption of ROM, increase of production costs with concurrent reduction of output - those are inevitable side effects of desired concentrate grade improvement. Large-scale complex analysis and surveys have been carried out aimed at concentrate grade improvement with concurrent output increase. Classification of feed in hydraulic cyclones (hereinafter referred to as hydrocyclones) has been the bottleneck for improvement of processing throughput and concentrate output. Hydrocyclone classification efficiency is 50-60% and further improvement is practically impossible. Actual circulating load may achieve as much as 500-600% while the optimal rate is 200-250%. Application of wet fine screening has been considered to improve iron ore concentrate grade. Objective of this work is to design processing flow diagram for unoxidized ferruginous quartzites with implementation of wet fine screening. Large-scale tests have been run in Crushing and Concentrating Plant with application of wet fine screening stage. These tests included application of wet fine screening in 2 and 3 stages of classification to separate desired grain sized material; replacement of hydrocyclone classification with fine screening; application of fine screening as additional stages to concentration process and screening of final concentrate. Testing Methods. EXPERIMENTS AS WELL AS THEORETICAL RESEARCH HAVE BEEN APPLIED FOR THE PURPOSES OF THIS WORK; INCLUDING MAGNETIC, GRAIN-SIZE AND CHEMICAL ANALYSIS OF CONCENTRATION PRODUCTS. MODERN ANALYTICAL DATABASE HAS BEEN APPLIED TO STUDY WET FINE SCREENING FEATURES, MINERAL AND PHYSICAL COMPOSITION OF CONCENTRATION PRODUCTS. Work Results: - analysis of wet fine screening application for iron ore concentration. - technological solutions enabling to improve slurry classification of fine ingrained low magnetic iron ore have been developed. - effective process flow diagram including fine screening has been designed based on the feasible and reasonable arrangement solutions."

Jan 1, 2018

By Megha Patel

"The objective of this project was to investigate the application of Prompt Gamma Neutron Activation Analysis (PGNAA) technology to provide real-time on-belt elemental analysis of feed ore in base metal sulphide processing, in this case at the Mount Isa Mines Zinc-Lead Concentrator Heavy Medium Plant (HMP). After initial exploratory testwork proved successful, a Geoscan On-Belt Elemental Analyser was retrofitted onto the existing HMP feed conveyor. Dynamic calibration of the Geoscan was conducted based on laboratory XRF analysis results of the HMP feed conveyor hammer autosampler samples from May to November 2013. Comparison of the Geoscan results to the laboratory XRF analysis results during and after dynamic calibration indicated the technology had acceptable accuracy to be incorporated into HMP process control. The variation between the two sets of data includes all primary sampling, sample preparation and XRF analysis errors as well as the Geoscan errors themselves. The Geoscan instrument precision must be calculated separately through a duplicate sampling campaign and independent laboratory analysis before extending the scope of its range of application beyond HMP process control. The expected benefits of integrating the Geoscan real-time data into HMP process control are optimised HMP metal recovery, improved cost efficiency and improved stability of the downstream processes (milling and flotation). Utilisation of the Geoscan will also enable improved feedback to mines on grade control and dilution, and provide additional information on individual ore types when fed as campaigns to HMP."

Jan 1, 2014

By H. Lieberwirth, M. Hesse

"Selective comminution (SC) is beneficial for the treatment of primary raw materials, especially if it is utilized in the pre-concentration process. Pre-concentration processes are applied in mineral processing to relieve subsequent processes and to achieve a higher efficiency. SC is also a promising method for the treatment of low-grade ores and waste dumps. With SC, various components can be separated such as valuable minerals from waste, ore from wall rock and different ore varieties within a deposit. SC is a property of a comminution system and leads either to a preferred crack propagation in one component (called preferential breakage) or to a preferred crack propagation along the grain boundaries (called interfacial breakage). SC results from different comminution behavior of various components in the feed material. For mechanical comminution, the preferential breakage seems to be the most important case of SC. Hereby SC generates only the difference in the particle size which can finally be used as a sorting parameter. A sorting process which uses SC depends on three parts: the feed material, the comminution machine and the separation machine. The feed material defines the potential for SC. Differences in properties like strength, toughness and density which are related to comminution are often used. The comminution machine has to exploit this potential. The extent of the exploitation can be influenced by the machine design, material and operational parameters. After SC, the various components are still combined in the product. So ultimately, a separation machine is needed. At preferential breakage, a simple screening machine can be used. The basics about SC will be presented at first. This contains relationships between material properties, the kind of loading in the comminution machine and the SC effect. These basics can be used for example to exploit a potential to SC for a pre-concentration step or to avoid the SC for a higher efficiency of subsequent processes. Based on recent investigations with impact load, the influence of the important parameters compressive strength, density, particle size and impact velocity to the SC will be shown, using examples of lead-zinc ore comminution and fluorspar processing."

Jan 1, 2018