Search Documents

By James E. Wennen

The through-put and energy efficiency of an autogenous (AG) grinding mill are adversely affected by variability in rock size and rock competency. This applies to both fully autogenous and semi-autogenous (SAG) grinding circuits. In this paper we focus on an approach to overcome the problem of inconsistent mill through-put related to variability in mill feed size and rock competency. The focus is on ores containing hard, competent rock. This approach consists of preparing feed to an autogenous mill that contains 20% coarse media rock and 80% of material crushed to pass 37 mm. Results of pilot-scale testing for two iron-ores will be presented to show that a 10% to 12% reduction in unit energy consumption is possible with prepared feed, compared with feeding the mill with conventional primary crusher discharge.

Jan 1, 2012

By P. A. Crane, N. Shirley, Aung Moe, H. M. Nicholson, D. Kan

Kazakhstan’s first commercial copper-leach solvent extraction-electrowinning plant, Central Asia Metals’ Kounrad project, was commissioned in April 2012. Exploiting low grade waste stockpiles produced during Soviet era open pit mining, a 10,000 tpa copper cathode plant was designed, constructed and commissioned within 18 months. Overcoming initial challenges with a workforce unfamiliar with the technology and with extensive periods of sub-zero conditions during winter the project has consistently met targets and produced high quality copper cathodes at cash costs of less than US$1/lb. Challenges encountered during the first two years of operation are described and future plans briefly discussed.

Jan 1, 2014

By K. van Netten, T. P. Ernst

"Froth flotation has been used successfully for about a century in the beneficiation of both coal and mineral particles. With the on-going trend towards lower feed grades, however, there is a need to transform this technology in ways that can deliver ultrafast separations, with strong selectivity, and recovery, covering a broader size range. It should be recognised that the hydrophobic effect, with its highly selective and long-range interactions, will most likely underpin any new technology. We identified the separation of the concentrate from the tailings as the rate determining step of conventional flotation technology. This limitation was then addressed by developing a novel flotation technology, insuring the formation of a concentrate that could be separated more rapidly from the tailings. We introduced a novel binder medium, a highly concentrated water in oil emulsion, to act as the focal point for hydrophobic adhesion, effectively replacing the air bubbles used in conventional flotation. The hydrophobic particles adhere to and become embedded within the binder, forming saturated agglomerates that float upwards. Moreover, by forming these large and resilient agglomerates, the product can be quickly dewatered over a screen and separated almost immediately from the tailings. Remarkably, this new binder permits residence times in the order of a few seconds under batch conditions. This paper examines the performance of the technology as a function of the oil wt% added to the slurry. The paper also examines the performance of the technology as a function of the particle size, showing a decline as the particle size exceeds 0.50 mm.INTRODUCTIONFroth flotation involves the collision and adhesion of hydrophobic particles to rising air bubbles, the carrying of those particles from the bubbly-pulp zone into a froth zone, and subsequent drainage and migration of the pulp to achieve the final concentrate (Wills, 2006). Within a Jameson Cell the feed slurry and air bubbles are brought into intense contact within the active area of the downcomer, achieving rapid kinetics of hydrophobic particle adhesion to the air bubbles (Harbort et al., 1994). However, once the bubble laden product and tailings emerge from the downcomer there is the need for separation of the concentrate from the tailings, an inherently slower process. In other devices such as mechanical cells the initial kinetics of particle adhesion are far slower, relying on the turbulent eddies throughout the cell, while in a column the kinetics rely upon an even slower process of bubble interception with suspended and settling particles (Gorain, 2007). However, in all cases the driving force for segregating the bubbles from the tailings, and the drainage of the froth are inherently the same. We do note, however, recent advances by Galvin and co-workers in achieving so-called Fast Flotation, utilizing a system of inclined channels to dramatically increase the segregation rate of bubbles from the tailings, permitting much higher gas and feed fluxes to be applied, achieving up to a ten-fold throughput advantage (Dickinson et al., 2014). Any further improvement within the existing flotation paradigm would require the introduction of centrifugal forces, but this would also require the formation of much finer bubbles than is typically used given the tendency of relatively large bubbles to reach a limiting slip velocity due to deformations and increased drag. Across all flotation devices we argue the rate determining step remains the segregation of the bubbles from the tailings."

Jan 1, 2016

By K. Adham

Both the dry and the wet fluorination systems require hydrogen fluoride (HF) for the process of uranium conversion to uranium hexafluoride (UF6). The dry methods depend on the electrolysis of HF to generate the fluorine (F2) required for the high temperature pyro-fluorination. The wet methods require aqueous HF in water solutions for the low temperature hydro-fluorination (Argonne, 2019). This paper uses the available HF safety guidelines and industry information to discuss the issues of transportation, storage and utilization. Health effects and environmental considerations are reviewed. Safe practices for handling the HF (both as anhydrous and as aqueous) are considered. Proper selection of different materials of construction are discussed, for both the anhydrous and the aqueous HF.

Jan 1, 2020

By C R. Evans

Whole-rock and muscovite potassium-argon dates from selected low-grade metamorphic rocks of Precambrian age in the Canadian Rocky Mountains near Jasper, Alberta, were obtained to ascertain the age of the source terrain and the age of the metamorphism. Ten argillites gave whole-rock dates ranging from 270 to 485 million years, dates which are apparently inter-mediate between the age of the source material and that of the metamorphism. "Up-dating" increases with the degree of orientation of muscovite in the cleavage plane, and with the ratio of the muscovite in the cleavage plane to that in the plane of the bedding. Detrital muscovite from four arenaceous rocks gave dates ranging from 1,050 to 1,780 million years. "Updating" increases with decreasing grain size, so that, within the range investigated, the cube of the median diameter (¢) of the muscovite is apparently proportional to the radiometric date.

Jan 1, 1964

By L. C. So, S. Faucher, S. Mostaghel, D. Sauter, S. -Y. Oh, S. K. Lee

"Molten material from pyrometallurgical furnaces is tapped at high temperature, carrying a large amount of heat. Traditional handling methods of slow air cooling or water granulation do not allow for the recovery of heat from slag and matte. Furthermore, water granulation adds an inherent safety risk of explosions. Recently, there have been numerous studies into processes attempting to recover waste heat. However, most of them have never been commercialized due to numerous challenges including scalability, cost, low heat recovery efficiencies, and difficulties in heat utilization. Ecomaister-Hatch has recently developed and commercialized a reliable and simple dry atomization system that allows for heat recovery while eliminating the use of water. Comparisons of pilot and commercialized dry atomization and heat recovery technologies will be presented and challenges of these technologies will be highlighted.INTRODUCTION Slag has traditionally been regarded as an undesired waste product from smelting operations with slag management focused on removal and disposal of “waste”. Over 500 million tonnes of slag are produced per year, carrying with it ~220 TWh of energy (Barati, Esfahani, & Utigard, 2011). Depending on the process, the energy content of slag ranges from 10-90% of the total energy input (Barati, 2011, Rodd, 2010). There has therefore been great interest in recovering energy from slag. Slag handling methods can broadly be classified into three categories: (1) dumping and slow cooling, (2) wet granulation and (3) dry granulation. As discussed below, only dry granulation routes are amenable to heat recovery. Slag dumping involves the slow cooling of molten material and crushing of the resulting solid. In this process, slag is dumped on the ground directly from furnaces or transferred to slag pots that are moved by rail or haulers and then dumped on the ground. The molten material is left to cool and solidify until it can be broken and handled by heavy machinery."

Jan 1, 2017

By Michel Guillot

Gaz metal arc welding is commonly used for producing large frames and assemblies. Even for light aluminum and thin wall assemblies, the GMAW technique is increasingly preferred over the GTAW technique. This is particularly true where the welding gun motion is achieved accurately with automated or robotic systems and when using pulsed or regulated metal deposition. In this study, butt joints in floor welding position are tested at speed ranging from 1.5 to 16 m/min. Attempts are made of find parameters providing good and repeatable joint quality with minimal distortion and good appearance even at high travelling speeds. Taguchi experimental plans are proposed with different parameters tested with sheet metal samples. The parameters include typical GMAW machine settings, joint preparation geometries, wire gages, gun angles, wire feeds, and more. The robot motion speed and the proximity of the part are also considered. Direct monitoring of machine welding current and voltage is achieved. Once is found the best set of parameter settings, additional tests are carried out to verify the repeatability of weld quality. Secondly, these conditions are applied for joining and testing a floor panel made of several extrusions. Weld quality is established with Vickers micro-hardness measurements, cross section geometries of the weld pool including penetration, tensile tests and metallographic observations to establish the amount of porosity and weld microstructure in the HAZ.

Jan 1, 2011

By Greg Gosson

"Early efforts to develop formal reporting systems to quantify and classify mineral deposits date back over 100 years. (e.g. Hoover 1909: “Proved, Probable, Prospective Ore”). This was at first driven by mine operators’ need for reliable estimates of what their mines could produce. Disruption of transportation routes by world wars prompted western governments to recognize the need for assessments of strategic sources of metals and minerals that could support domestic industry during times of crisis. Categories were created to quantify mineral potential which were additional to those of mine reserves. Terms such as hypothetical and undiscovered resources entered the lexicon. Capital markets serving the mining industry were traumatized during the latter part of the 20th century by undisciplined and fraudulent disclosure by exploration companies of mineral deposit potential. Government securities regulators pressed for the development of credible reporting codes (e.g. SEC Industry Guide 7: 1981; JORC 1989; SAMREC 1994, CIM 2000). Representative organizations from the major western mining countries generally agreed that there should only be three categories of mineral resources (measured, indicated, and inferred) and two categories of mineral reserves (proven and probable). This was formalized in 1997 with the “Denver Accord”. Acceptance of the standard terminology may have been the easy part, because the challenge for the 21st century is to get general industry acceptance and agreement of the principles behind the definitions of each category. There has been noticeable movement towards this objective in the last few years. This is reflected in part in the updated reporting codes by JORC 2004, CIM 2005; SAMREC 2007; SME 2007; and PERC 2008, and the development of the CRIRSCO International Reporting Template 2007."

Jan 1, 2003

By H. J. McQueen

About 1973 the abrupt decrease in crude oil shipments due to political action by Middle Eastern suppliers, caused a shortage and a steep price rise. In response, Canada had to develop strategies of diminishing consumption and increasing production in both traditional and environmentally friendly resources. To clarify the situation in Canada, there are brief histories of energy (discovery, pipelines), manufacturing and science development, 1800-1970. Energy strategies, both nationally and in Quebec, succeeded in curbing consumption and in expanding production while fostering research in renewable sources. The industry-sector committees provided free exchange of conservation techniques through the federal energy ministry, with progress reports issued annually. Pipeline history in North America is reviewed along with manufacture and construction plans in Canada. Considerable success in all the aspects provided long lasting benefits, but after the embargo was lifted, many research initiatives were gradually abandoned for political reasons. Sustainability is the goal; society must conduct conserver analysis, legislation and action to enhance it.

Jan 1, 2015

By Alan S. Lock

Large scale feasibility studies for the establishment of oil-seed and cellulose producing crops on mine tailings have been successfully conducted over 1 growing season with the purpose of these crops to be used as feedstock to the biofuels industry. An acid sulphide tailings impoundment in Copper Cliff, Ontario and a near neutral pH goldmine tailings impoundment in Timmins, Ontario were both tested by amending half hectare plots to approximately 1 m thick with residual biosolids from the pulp and paper industry and growing canola and corn on these plots. Full scale agricultural equipment was used to cultivate seed and harvest the plots to prove the full scale feasibility of farming on these biosolids. The vegetation development, growth, yield, quality and composition were assessed to identify the best species that would maximize biomass development for feedstock to the biofuels industry and carbon credits for the mining industry. Groundwater, biosolids and tailings chemistries were investigated to identify potential deleterious impacts of degrading organic matter on tailings metal mobility. Preliminary hydrologic investigations using moisture sensor profiles elucidate potential conservation of water in amended plots. Tailings amended with biosolids have the potential to provide the mining industry with carbon credits and supply feedstock to this new industry while reclaiming brownfields to a new level, utilizing industrial and municipal organic waste material.

May 1, 2009

By Renato Macciotta

The argillaceous formation known as the Opalinus Clay is host to the Mont Terri Underground Research Laboratory. The URL was developed to investigate the hydrogeological, geochemical and geotechnical properties of the formation. Underground excavations at the site are characterized by non-elastic and time-dependent deformations. Excavations trending perpendicular to the strike of the bedding presented relatively minor deformations, however, tunnels parallel to the strike of the bedding showed much larger non-elastic deformations. This paper presents an analysis of the measured response of a tunnel trending parallel to the strike of the bedding in Opalinus Clay. The measured convergence is compared to tunnel experience in weak rocks to assess the tunnel stability.

Jun 1, 2012

By Alain Tshilombo, Vijay Reddy, Chowdary Meenavilli, Kelvin Buban, Cory Kosinski, Sriraj Meenavilli, Siddhartha Tirumalaraju

The use of artificial intelligence (AI) for process optimization is expected to play an increasingly important role in the future of the mining industry. The objective of AI is to develop a data driven soft (virtual) sensor using historical data that can estimate unmeasurable characteristics of the process and provide appropriate recommendations during operation to optimize the process through continuous learning. The application of AI to a hydrometallurgical process was evaluated by Sherritt Technologies in coordination with NTWIST. Historical operating data obtained from the Ambatovy facility’s High Pressure Acid Leach (HPAL) circuit was used to develop models to predict autoclave discharge parameters based on operating conditions and ore mineralogy. The prediction models were developed in such a way to also allow the user to simulate and test different operating conditions. A second set of models (AI model) were developed based on the prediction models, economic data and operating constraints for a given process unit to identify optimal reagent and steam dosages across the HPAL circuit. The development of these models was significantly complex due to the dynamic and interactive nature of the HPAL process. Despite the complexity of the models, the models were able to predict, with accuracy, the relationship between ore composition, leach autoclaves retention time, acid addition and steam addition with metal extractions as well as levels of impurities in the autoclave discharge slurry. The study showed that AI has the potential to improve the overall operation of a facility through providing tools to assist with training, troubleshooting and process optimization. INTRODUCTION The Ambatovy project, located in Madagascar, is one of the world’s largest nickel and cobalt mining and processing operation, with a design capacity of 60.000 tonnes of nickel and 5,600 tonnes of cobalt per year (Collins et al., 2016). Commissioning and start-up of the Ambatovy mine and plant facilities were completed in 2012, with acid first introduced to the ore leach in March 2012. Commercial production (defined as 70% of design capacity) was achieved in January 2014 and the production level required to achieve financial completion (90% of design capacity for 90 days) was achieved in March 2015 (Valle et al., 2016). Figure 1 shows a simplified flowsheet of the hydrometallurgical pressure acid leach (PAL) process employed by Ambatovy.

Jan 1, 2019

By H. J. lgner

Hydraulic fills are widely used in the tabular, steeply dipping stopes of the South African gold and platinum mines as an integrated process within a daily cycle of drill and blast. There is therefore only a small time window in which to fill the geotextile bags used as primary fill containment, without the risk of loosing production. Consequently, mines tend to increase the flow rate to the stopes, although this compromises adequate drainage, consolidation and strength development during filling. Recent underground measurements inside the geotextile bag have revealed that at high rates of rise and at 25 degrees dip, the backfill can remobilise within a limited area inside the geotextile bag during filling. This sudden downward surge of backfill exerts, for only a few seconds, additional loading on the geotextile, its supporting mesh and the props. This unstable behaviour poses a serious threat as it can push props out of place, thereby damaging the geotextile bag and causing a mud slide in the stope. To reduce the risk of accidents, the phenomenon of sudden slumping was further investigated for various filling conditions in the laboratory. The results confirmed that the maximum pressures associated with the sudden slumping can be more than five times those experienced during steady-state consolidation. Based on this new insight, the current best practice for hydraulic backfilling was critically reviewed. A practical approach to implementing meaningful standards is presented to ensure safe operations in relation to the consistency of the backfill quality and the appropriate matching of geotextile characteristics with backfill properties.

May 1, 2007

By Robert D. McKellar, Luke Frawley, Okrasa. Richard

"The resource industries in Canada are facing increasing global competition and stringent environmental regulations. This has made it essential for companies to lower operating costs wherever possible. Electrical energy rep-resents one variable cost that may be better managed and utilized, providing the user with lower operating costs, improved productivity and better yields.The utility industry is also facing changes in the way it must do business. Utilities in North America are facing the prospect of deregulation that will eliminate the monopoly they have traditionally held. This will force them to strive for lower operating costs, to maintain a competitive position and to improve customer ser-vice so as to maintain their customer base.Ontario Hydro has been working with industry for several years. Many opportunities for cost savings have been identified involving energy efficiency, process improvements and the use of new electro technologies. One useful service that the utility can offer industry is to increase the awareness of potential opportunities suited to their operations. This paper will provide an overview of some of the projects that have been implemented and those that are presently being evaluated. An electronic data-base of electro technology applications that is under development will also be described."

Jan 1, 1996

By M. W. Grabinsky, J. H. Curran

"Characterizing the spatial distribution of rock stresses is a challenge, especially in the geologically complex environments typically found at most metalliferous mines. Therefore, instead of focusing, specifically, on the task of making stress measurements, the engineer should instead attempt to develop a better understanding of the interaction between stress, mining geometry and rock mass behaviour. This paper demonstrates such an approach using a Canadian Shield hardrock mine case study, in which geomechanical models are used to relate stress, mining geometry, and rock mass properties to observed excavation response, and numerical modelling is used to better quantify this interaction.IntroductionUnderstanding how the mine geometry, field stresses and rock mass interact to produce the observed rock mass response to mining can be a significant challenge. Consider our present ability to quantify the basic geomechanical design input data. Mine geometry is normally quantified in more detail than is required for analysis purposes. Our understanding of rock mass strength and stiffness is far from complete, but established procedures do exist to obtain estimates of these parameters based on index and laboratory testing data and field mapping. Our ability to quantify field stresses is probably the most limited, in part because stress measurements are difficult and expensive to carry out, and in part because the stresses vary to an unknown degree from point to point within the rock mass. The engineer must, therefore, consider whether or not stress measurements are justified and, when they are, where the average stress state needs to be quantified and how many of which type of measurements will be required to determine the average stresses.Such was the case at Ansil mine, a massive sulphide deposit in hard rock located at a depth of more than one kilometre in the northern Québec portion of the Canadian Shield. The Ansil orebody was relatively rich, but small, with the potential for significant stress-related problems. As a result, geomechanical design had to be done carefully from the start – there would be little opportunity to modify the mining strategy once production had begun, and the economic consequences of stope dilution and rock mass instability would be severe. An extensive stress measurement campaign was carried out, but the determined stress magnitudes were unexpectedly low. The designers were, therefore, faced with a dilemma:"

Jan 1, 1997

By K. D. Watson

"THE Mindamar zinc-lead-copper mine, owned by Mindamar Metals Corporation Limited, is at Stirling in Richmond County, near the south-eastern shore of Cape Breton Island, Nova Scotia (Figure I). It is connected by several roads with the Canadian National railway at Sydney and St. Peters.The deposit is said to have been discovered around 1895 as an outcrop in the bed of Copper brook, but the details are obscure. Not until 1925, when it was optioned by American Cyanamid Company, was it developed underground. Between 1927 and 1938, the 1-nine was operated intermittently by The British Metal Corporation (Canada) Limited, and yielded approximately 200,000 tons of ore averaging about IO per cent zinc, 2 per cent lead, I per cent copper, and small quantities of silver and gold. In December 1950, Dome Exploration (Canada) Limited made an agreement with Mindamar Metaî Corporation Limited, which was exploring the old mine, to assume management and prepare the property for production. Production started in April 1952 with a new mill and a new four-compartment shaft, and between that time and the end of 1954 it has totalled 545,347 tons of ore averaging 5·89 per cent zinc, 1·35 per cent lead, 0·66 per cent copper, 0·032 oz. gold, and 2 151 oz. silver.The Mindamar orebodies are irregular lenses and large veins lying within a wide, almost vertical shear zone of remarkable persistency. The shear zone consists mainly of well-foliated sericite schist derived from siliceous siltstone, and it contains a vast amount of dolomite and magne-site of hydrothermal origin. Most of the ore is extremely fine-grained and some of the high-grade material has a conspicuous thinly layered structure. The metallic minerals, in order of decreasing abundance, are pyrite, sphalerite, chalcopyrite, galena, and tennantite; the gangue minerals, in the same order, are dolomite and magnesite, quartz, sericite, talc, chlorite, barite, albite, and alunite.The geological setting of the deposit is shown in Figure 2. Except along streams and lake shores, almost all of the bedrock is concealed by glacial drift. The group of rocks in which the deposit occurs consists principally of greywacke, siltstone, tuff, brecoia, and Javas, and has been correlated lithologically with the Bourinot group of Middle Cambrian age. A short distance west of the mine, these rocks are in contact along the Stirling fault with conglomerate, arkosic sandstone, and quartzite belonging to the Middle River group of Silurian or Devonian (?) age, which elsewhere in the area overlies the Bourinot group unconformably. The large bodies of granitic rocks in the region, and the large lenticular masses of diorite and quartz diorite associated with them, have been assigned by Weeks (5, pp. 68-69) to the Devonian."

Jan 1, 1949

By T. Marolt, J. Likar, E. Grøv, J. Žarn

"Underground structures are an integral part of the infrastructure of modern society and are used for a wide range of applications, including subways and railways, highways, not at least nuclear facilities. When the wider area is subject to earthquake activity, underground constructions should be analyzed on seismic and static loading. Observations showed that the underground structures have significantly less seismic risk than surface structures. Available methods allowed analyzing the magnitude of risk for different input parameters of seismic loads in different ground environment. Simulation of earthquake loading on underground structures, in the present paper is given the various aspects of analyzing the potential damage and instability of underground facilities. INTRODUCTIONThe development of methods and computing resources used for para-seismic engineering has finetuned the evaluation of the seismic strength of buildings and equipment. Reinforcements may therefore be decided, not simply on the basis of a reassessment of the hazard, which constitutes input data for the calculation of structures and equipment, but also on the basis of developments in para-seismic engineering. Underground facilities are an integral part of the infrastructure of modern society and are used for a wide range of applications, including subways and railways, highways, material storage, and sewage and water transport and not at least nuclear facilities. Although in the past showed that the underground structures are significantly less seismic risk than on the surface, the professional researches and their results are accessible. Seismic resistance of underground structures is analyzed from several aspects. The currently available methods allowed analyzing the magnitude of risk for different input parameters of seismic loads in different ground environment. For better interpretation of earthquake loading on underground structures, are given below the various aspects of analyzing the potential damage and instability of underground facilities in rock. One of the early studies which covered this are of investigation were prepared by Dowding and Rozen (1978). They grouped damages due to earthquakes in underground structures into three main categories:- damage from ground shaking- damage from fault dislocation- damage by earthquake-induced ground failures (e.g. liquefaction and landslides)."

Jan 1, 2015

By Barry Hope, Javier Rico

"Goldcorp’s Hoyle Pond mine has recently completed several projects which have impacted the overall ventilation system. The project includes extending the Fresh Air Raise (FAR) to depth, development of a new Return Air Raise (RAR), and the installation of new sensors and ventilation controls throughout the mine. Two years after the completion of #2 Winze, the mine is ramping up its ore production to 1,300 tpd (up from 1,100). To ensure safe and profitable production, a reliance upon technology has been needed to provide the required ventilation to the work areas according to the mine plan. To systematically assess the mine’s ventilation in real-time, a significant increase in remote monitoring was required. This included installing additional flow, pressure, temperature and gas sensors. The first step in upgrading the existing monitoring was to purchase airflow and differential pressure monitors and install them in key areas of the mine. This paper presents the process of expanding the monitoring capability at Hoyle Pond mine, the selected equipment and the results of the implementation. The intended goal was to improve safety while minimizing capital and operation costs. The monitors were installed in strategic locations to provide immediate feedback on the impact of changes to the primary ventilation airflows. Comparing the available sensor technologies, installing them and systematically monitoring the ventilation served as a first step towards developing a mine wide Ventilation Control System. In addition, the initial state of the monitoring and control system, with final results and the chosen solution for the mine site, are presented. INTRODUCTION The Hoyle Pond mine is located in the City of Timmins, within the Porcupine mining district, Ontario, which has produced more than 70 million ounces of gold since 1910. Currently, approximately 60% of Porcupine Gold Mines gold production comes from the Hoyle Pond underground mine. Mechanized cut and fill and long-hole mining methods are used to extract the ore. The remainder of the ore comes from the Hollinger Open Pit mine. The Dome Underground mine ceased operations in 2017. Hoyle Pond is currently mining at 1820 meters below the surface and plans to go deeper. The average dry-bulb as wet-bulb temperature underground varies according to the depth and surface conditions which has extremes of –40°C in winter to +30°C in summer. The total airflow volume pushed down from surface is 240 m3/s to accommodate the diesel-powered equipment needed for normal operations. In order to improve the quality of air underground a program has been implemented to use diesel particulate filters, starting with the truck fleet and 6-yard scoops, followed by the intention to implement the rest of the functional diesel-powered equipment and eventually move to electric equipment."

Jan 1, 2019

By J. Awmack, M. A. Tomlinson, P. J. Lind

"Peñasquito is a complex polymetallic deposit containing gold, silver, lead, zinc, and copper and is one of the largest producers of gold in Mexico. Mining activity is currently transitioning to a second open pit, Chile Colorado, which will be mined concurrently with the existing open pit, Peñasco. The ore bodies are located within diatreme pipes and into the surrounding sediment formation. In the coming years, mining will be carried out in more sedimentary zones, which are significantly higher in organic carbon content. Organic carbon in the feed influences both flotation and leaching operations. Several changes are being implemented to the Peñasquito flowsheet to mitigate the effects of increased organic carbon in the plant feed. These include the use of alternate reagent schemes, construction of a carbon pre-flotation circuit, implementation of a pre-leach flotation circuit ahead of pyrite leach, and evaluation of a tertiary process for separation of carbon and precious metal minerals.INTRODUCTION Goldcorp’s Peñasquito operation is located in the Mexican state of Zacatecas, approximately 200 km from the city of Zacatecas in the Mazapil municipality (Figure 1). Peñasquito has been in operation since 2009, with mining carried out by open-pit methods. Oxide ore has been processed in a heap leach facility and sulfide ore is treated in the sulfide processing plant. The processing capacity of the sulfide plant is 130,000 tonnes of ore per day and in 2016 production amounted to 465,000 ounces of gold, 17.6 million ounces of silver, 109 million lb of contained lead in lead concentrate, and 263 million lb of contained zinc in zinc concentrate (Goldcorp Inc., 2017). To recover more of the contained gold and silver and to mitigate the impact of increasing organic carbon content in the ore, a number of significant changes are being made to the operation."

Jan 1, 2018

By R. B. Nourse, S. F. Gwynn-Jones, S. Nikolic, M. L. Bakker, I. McDougall, H. Joubert

"Tenova Pyromet’s core furnace knowhow and expertise has been built within the ferroalloy and nickel/platinum group metal (PGM) industries with the supply of electric furnaces for a number of nickel/PGM operators, including Eastplats, Lonmin, and Anglo-Platinum in South Africa, Mineraçào Serra Da Fortaleza in Brazil, and Norilsk Nickel in Russia. Tenova Pyromet has also supplied the electrode columns and associated electrode equipment – the heart of the electric furnace technology – for cobalt recovery in furnaces in Zambia and the Democratic Republic of the Congo. The quantity and size of projects undertaken by Tenova Pyromet has provided the opportunity to continuously improve furnace designs and the scope of supply, culminating in the most recent nickel/PGM project currently under construction at Northam Platinum. Through this innovative culture, the Tenova Pyromet Base Metals Initiative was formed in 2015 to develop the Novasmelt™ Furnace; a next generation optimised Top Submerged Lance (TSL) furnace design. The combination of Tenova Pyromet’s advanced Novasmelt™ product with our industry leading electric furnace technology are discussed with reference to applications for nickel and cobalt production. Flowsheet arrangements are compared summarising potential capital savings, operating requirements and achievement of downstream product quality.INTRODUCTION Tenova Pyromet is a leading player in the field of smelting technology development and equipment supply. Tenova Pyromet is the result of the union of three furnace suppliers under the Tenova banner: Techint Technologies (Tagliaferri), Core Furnace Systems Corp (Lectromelt) and Pyromet Technologies. The furnace experience of the combined groups dates back over a century with the earliest Lectromelt going into production in the early 1900s. Throughout the modern era, Tenova Pyromet has developed a reputation for providing dependable innovative smelting technology, high quality equipment and sound project execution to a worldwide client base with customer plants operating in Europe, Southern Africa, North America, South America, Russia, Kazakhstan, the Middle East, South Korea, and India. Tenova Pyromet’s core knowledge and expertise was developed in the South African ferroalloy, base metals, and platinum group metals (PGM) smelting industries. Tenova Pyromet has spent considerable effort on development and has contributed significantly to improve the state of the smelting industry. Tenova Pyromet’s electrode columns have become widely renowned and are now providing significant benefits, especially in increased furnace availability, to many smelting furnace operators. The electrode column is the heart of the furnace as it delivers a controlled amount of electrical energy, at an optimum depth in the burden/bath, to the smelting process. Every furnace is custom designed to the specific operating range and optimal operating point of that furnace and process"

Jan 1, 2017