Search Documents

By S. Banisi, J. A. Finch, A. R. Laplante

"A technique for on-line simultaneous estimation of gas and solids holdup (volume fraction), based on a combination of conductivity and pressure difference measurements, is proposed and tested in a laboratory flotation column (10cm in diameter and 447cm in height). Fundamental concepts underlying this technique and the effect of relevant parameters are discussed. In the studied range, 3-30 %v/v gas holdup and 2-18 % v/v solids holdup, experimental results showed good agreement between the estimated and actual holdup values (as determined by an isolating technique). The relative accuracy of the solids holdup estimation increased when solids density or solids concentration increased. Frequent re-calibration of pressure transducers was found necessary for accurate phase holdup estimation.IntroductionGas holdup is a key parameter in controlling the performance of flotation columns. For example, flotation rate is affected by bubble size and gas rate both of which, in turn, affect gas holdup. Moreover, gas holdup also determines the slurry residence time which indicates a direct influence of gas holdup on recovery.Gas holdup determination has been the focus of many studies (e.g., Castillejos, 1986; Marchese et al., 1992). Some of the techniques which have been used are given in Table 1."

Jan 1, 1994

By G. W. H. Norman

"During the past few years emphasis has been placed on the importance of major faults, fault zones, and associated structures in localizing ore deposition. This interest has developed partly through experience in mining camps in other parts of the world, and partly by the discovery of such structures associated with ore deposits in the Abitibi region, northwestern Quebec. The recognition of these structures has been brought about chiefly by detailed mapping that has been gradually extended along most of the southern gold belt of Quebec and across adjacent parts of Ontario. In the Chibougamau region of northern Abitibi, progress has been made in mapping major faults by using aeroplane photographs with a scale of about 1,000 feet to 1 inch for field mapping. These studies have shown that many large faults occur in the Abitibi region; also that there is a relationship, direct or indirect, between faults and mineral deposition. The faults are, however, of more than one type and age, and this should be clearly appreciated in any planned programme for prospecting this great region adequately.Geology of the Abitibi RegionGeneral GeologyFaults of more than one age and type occur in the Abitibi region. In order to appreciate some of the age relationships of the faults, a brief summary of the historical aspects and major structural features of the geology (fig. 1) is necessary. These historical aspects may be briefly summarized in chronological order as follows:(1) Accumulation of Archæan lavas and associated pyroclastic rocks, either alternating with, or essentially followed by, deposition of sedimentary rocks, and interrupted at least once by local and perhaps regional folding and erosion."

Jan 1, 1954

By Robert J. McCarthy

Many technologies have been adopted over the last half century for the haulage of material from open pit mining operations. Some of the technologies utilized include rail, off-highway trucks, conveyors, and slurry pipelines - each having its unique application and benefits. Over time, truck haulage has become the primary means of surface mine material movement, though recently it has been plagued by problems of tire shortages, high diesel fuel costs, labour shortages, and carbon emissions. This paper focuses on In-Pit Crushing and Conveying (IPCC) as a competitor to truck haulage which has the potential to solve many of these problems. An overview of the available technology is presented along with measures required to overcome perceptional if not physical barriers to implementing this technology in modern open pit mines.

May 1, 2011

By C. O. Swanson

THE purpose of this paper is to discuss the use of the dip needle in the field of mining geology. The subject matter is new only to the extent that it reflects the writer' s added experience in recent years. The treatment is brief, and those interested in a more extended analysis are referred to the articles listed at the end of the paper. In the discovery and tracing of mineral deposits, the clip needle, like most other geophysical instruments, can be used in two ways. One method may be termed direct; the other, indirect. The direct method is that of finding or following certain ore-bodies by virtue of their magnetic properties. Explicitly, or by inference, it is the method which many mining men and practising geophysicists have in mind when they consider whether or not a certain property should be studied by geophysical means. In the ideal case, this method demands little or no knowledge of geological conditions. The indirect method uses the clip needle as an aid to purely geological studies in working out the structure of a mineralized area. Although not as simple as the direct method, it enjoys a much wider field of usefulness. The writer's experience in the past fifteen years, which is believed to be typical, is that the indirect method finds application four or five times as often as the direct method. The indirect method is of particular value because it furnishes information concerning the relationship between geological structure and ore occurrence. Most mining engineers will agree that structural control is an important factor in the localization of ore deposits, and therefore that the subject under consideration is of some interest in mining geology. Specifically, then, the present purpose is to outline the principles and practice of using the clip needle in working? out geological structure.

Jan 1, 1941

By H. A. Khorami, T. Wong, B. Velapatino, E. Asselin, T. Donnelly, E. Bryce, R. Dixon

A copper–nickel concentration gradient alloy was designed and fabricated through a powder metallurgy (PM) process. Copper and nickel powders were mixed with different weight ratios from 0 to 100% copper in 10% increments. Each powder mixture was poured inside a cylindrical die and compacted between two punches using a hydraulic press machine at pressures up to 70 MPa, resulting in approximately 1 mm thick layers (discs) of pressed Cu–Ni powder. These 11 Cu–Ni compacted powder layers, i.e. 0–100% Cu with 10% increments, were then compressed together with pressures up to 420 MPa to form a green part. The green part was sintered in a vacuum furnace at 1000°C for 10 hours to form a solid mass (PM part) of Cu–Ni concentration gradient alloy. In the sintering process, Cu and Ni particles fused together and formed a single piece due to diffusion of the atoms across the boundaries of the particles. The diffusion of atoms also converted the stepwise concentration change into a uniform concentration gradient. INTRODUCTION Copper has numerous applications in different industrial sectors due to its superior physical, electrical, mechanical and chemical properties such as its excellent thermal and electrical conductivity, resistance to fatigue, high ductility, and resistance to corrosion. Moreover, copper and its alloys have natural antimicrobial properties. This has opened up new applications for copper–based self–disinfecting surfaces in healthcare in an effort to mitigate healthcare–associated infections (HAIs). HAIs affect millions of patients each year, leading to significant morbidity and mortality as well as financial losses to healthcare systems (World Health Organization, 2016). HAIs spread through three main routes: (a) iatrogenic in which HAIs are a direct consequence of medical encounters and/or treatment; (b) person to person where organisms are transferred between healthcare workers, patients, and visitors; and (c) environmental where transmission occurs via contaminated surfaces and equipment (e.g. doorknobs, railings, toilets/commodes, medical carts). The use of antimicrobial copper–based materials on high touch surfaces could diminish pathogen transmission via this latter rout. This has subsequently led to the development of a variety of copper–based materials for use in healthcare settings and promoted the investigation of the antimicrobial efficacy of copper–based materials.

Jan 1, 2019

By T. J. Fee

Introduction The International Nickel Company have been pioneers in mine rescue work in Ontario. Following the fire in the Hollinger mine in the spring of 1928, the Company purchased ten self-contained oxygen breathing outfits, ten all-service gas masks, an oxygen high-pressure pump, life line, inhalator, ten cap-lamps with batteries, and a complete stock of spare and accessory parts. An instructor from the U.S. Bureau of Mines, Pittsburgh, came to the Creighton mine for one week and trained twenty men in the use and limitations of all equipment. Monthly training courses were commenced in the fall, and have continued to the present time. Of the original twenty men trained, ten are still on the Creighton mine rescue teams. In the meantime, and as an aftermath of the Hollinger fire, the Work-men's Compensation Board of Ontario and the Ontario Department of Mines established a central mine rescue station at Timmins. This was completed in the spring of 1930. It was then decided, in view of the great expansion in mine development in the Sudbury district, to build and equip a similar station to serve all the mines there, namely, Creighton, Frood, Garson, Falconbridge, Sudbury Basin, and Errington. An extensive survey was made and a central location selected opposite the Frood mine. The International Nickel Company donated a site, and the station was completed in the fall of 1930. The station is a two-storey brick building, 27 ft. by 47 ft., with a large garage adjoining it. The ground floor is used for equipment and for training the crews. On the second floor are living quarters for the superintendent and his family. The garage houses a closed truck, in which all necessary equipment can be taken to any desired point for training purposes or for actual mine rescue work, if and when necessary. The garage is also used as a gas room, where the men are trained in an irrespirable atmosphere. A gas-tight observation window between it and the training room enables the superintendent to see and direct the men undergoing training, weight exercisers and other devices being used.

Jan 1, 1935

By Norm Clegg

The Plant Engineering and Maintenance Association of Canada PEMAC is a national, not-for-profit industry association for plant and facility maintenance, engineering and physical asset management in all industry sectors in Canada. Our mission is to provide professional development for our members and the profession in Canada

Feb 1, 2008

By C. A. Lorenson

THE Marmoraton mine is located a mile southeast of Marmora, a village in Hastings county, Ontario, 130 miles east from Toronto and 143 miles west of Ottawa. Highway No. 14 from Belleville intersects Highway No. 7 at Marmora and the branch line of the Canadian National railway between Trenton and Bancroft passes through the property just east of the open pit. HISTORY AND GEOLOGY The Marmora orebody appears as the whorls of a thumb print on the aeromagnetic survey map released by the Ontario Department of Min.es early in 1950, the survey of the district having been made in 1948 and 1949, under the joint auspices of the Department of Mines and the Geological Survey of Canada. The 'anomaly' appeared to have interesting possibilities, so Bethlehem representatives carried out a ground survey and began drilling the property in June, 1950. A total of 40 holes, aggregating 37,000 feet, were drilled to delineate the ore-body. The Marmora orebody is a re-placement of Precambrian limesto.ne with zones or bands of magnetite interlaid with metamorpl1ic rocks and cut by later intrusives. The ore and associated Precambrian rocks are overlain by 100 to 150 feet of flat-lying Palaeozoic limestone. It is a low-grade deposit averaging 33 per cent iron and requires concentration to raise it to 65 per cent iron grade.

Jan 1, 1958

By W G. Brese

The attention of the world is being focused on the spectacular rise of elemental sulphur production in Alberta. In the short space of a decade, production has increased from less than 10,000 long tons, in 1952, to al-most 1,000,000 long tons in 1962. Moreover, 1963 sulphur production is expected to rise by 50 per cent to approximately 1,500,000 long tons, and further increases are forecast for ensuing years. The reason for this dramatic in-crease in elemental sulphur production, particularly in the last year or two, is that Alberta elemental sulphur is recovered in association with the production of sour natural gas. When very large volumes of natural gas began moving to U.S. markets in the latter part of 1961, the resultant increase in sour gas production led to a marked increase in the production of sulphur. Consequently, Canada, mainly on the strength of sulphur produced in Alberta, will soon become the second largest producer of sulphur in the Free World

Jan 1, 1963

By D. G. Sediako

Chemical composition and the casting/rolling production routes determine the cost and properties of the wrought material. For example, the coarse-grained structure frequently associated with DC casting requires complex rolling schedules to refine the grain size. Hot forming (rolling/forging/extrusion) results in a strong crystallographic texture, which is responsible for the tension-compression strength asymmetry frequently exhibited by magnesium alloys. Understanding the influence of alloy composition on texture evolution during forming provides useful practical information to optimize industrial hot-forming technologies for magnesium alloys. In this study, a series of Mg-based alloys containing varying combinations of Al, Rare Earths, Zn, Ca, and Sr were subjected to identical casting and extrusion processes in order to isolate the effects of alloy composition on texture evolution. Textures were measured by neutron diffraction at the NRC Canadian Neutron Beam Centre. The ability of neutrons to penetrate deeply into materials allowed information to be retrieved from all regions of the bulk specimens without destructive and time-consuming sectioning operations, thereby providing true bulk texture data. {1010} , (0002), {1011}, and {1012} pole figures were generated for all of the as-processed alloys, from which Orientation Density Functions were obtained. The were then used to reconstruct the pole figures and to extract semi-quantitative texture data showing how the (0002) and {1010} planes align themselves with respect to the extrusion axis. It was found that varying the concentration of aluminum (3-4 wt%) and Rare Earths (2-3 wt%) in AE alloys had a weak effect on texture development. All of the alloys showed similar magnesium extrusion textures, in which the (0002) poles align themselves preferentially with the extrusion axis. The substitution of Sr for Rare Earths also did not have a significant impact on texture development. On the other hand, while the presence of small amounts of Zn and Rare Earths did not have a strong effect on texture development, alloys with higher concentrations of these alloying additions (in combination) showed an enhanced tendency for the {1010} poles to align themselves with the extrusion axis. The addition of Ca also enhanced the alignment of the {1010} poles with the extrusion axis. These textures can complicate further processing and introduce a significant anisotropy that could influence creep properties.

Jan 1, 2007

By C. W. Taylor, F. L. Martin

"THE DICTIONARY defines Metallurgy as the ""science or art of separating metals from their ores and refining them for use"". In these days, however, such a definition is not detailed enough.The modern science of metallurgy is based on two fundamental sciences, physics .and chemistry, and is sub-divided into two major fields: Process Metallurgy and Physical Metallurgy. These fields of metallurgy are now so comprehensive and involved that even the graduate metallurgist has to specialize in one or the other.In recent years, the relatively new science or technology of non• destructive testing has also entered the industrial scene, with tremendous impact and ramifications. So much so that, certainly, no .discussion on metallurgy can be complete without including some reference to it.Obviously, one paper cannot hope to cover in detail the relationship of the whole science of metallurgy to the mining industry. Consequently, only a very brief reference will be made to the field of Process Metallurgy, our major concern being with Physical Metallurgy and Non-Destructive Testing."

Jan 1, 1960

By Omkar N. S. Beruar

Extraction of sill pillars has always been problematic because of high risk of seismicity and rockburst. Depending on a number of factors, a sill pillar can undergo different failure modes and cause problems in the mine. Of these, sudden and uncontrolled failure of part(s) of the pillar leading to highenergy seismic events and rockbursts is a main concern because it is not possible to predict the location and time of a rockburst apart from its potential to cause extensive damage to the mine structures. To date, a comprehensive technique for sill pillar design and recovery does not exist. Conventional methods of pillar design, such as the pillar stability graph method, are utilized to design stiff sill pillars. In these design approaches, the post-peak response of the pillar-rock system is not considered. This is in part due to a lack of clear and comprehensive understanding of the post-peak behaviour and failure mechanism of sill pillars. In general, the strength of a rockmass is described using a failure criterion. When stresses reach the strength of the rockmass, the rockmass does not necessarily become unstable and knowledge of the loads alone is not enough to assess the instability conditions accurately. In fact, it is not possible to predict instability of rockmass based on the strength/stress ratio alone because instability depends not only on this ratio but also on the loading condition and loading system characteristics. The loading system can dictate whether the sill pillar will go through a stable or unstable failure process. This paper examines the influence of various parameters such as the pillar width to height ratio, the extraction rate, and placement of backfill on the Loading System Stiffness (LSS) and the Pillar Stiffness (PSS). The ultimate goal is to design yielding sill pillars that would yield in a stable manner and will reduce the risk of pillar rockburst. Plane strain finite element analysis is conducted using the generalized Hoek-Brown failure criterion with elastic-brittle-plastic parameters. Examples are given to demonstrate how to calculate these stiffness values and assess the stability condition of sill pillars. It is found that increasing the rate of extraction increases the likelihood of unstable yielding of the pillar as has been found in other studies. Placement of backfill in a timely fashion in the stopes above and below the sill pillars increases the stiffness of the loading system. This indicates that backfilling of stopes while creating the sill pillar increases the likelihood of stable yielding of the sill pillar.

Aug 1, 2013

By D. A. Barr

"The Galore Creek copper deposits are situated in the Stikine River district, 640 miles northwest of Vancouver, British Columbia. The deposits are primary cupriferous replacements localized in highly fractured zones lying in altered sedimentary, extrusive and intrusive rocks near the contacts of a potash-rich syenite porphyry complex which forms the core of a structural dome in Upper Triassic volcanic and sedimentary rocks. Ten deposits are distributed over an area of 3.5 by 2 miles and through an elevation range of 4,000 feet. The deposits share many of the characteristic features common to both the porphyry copper type of mineralization and pyrometasomatic deposits.Primary mineralization includes chalcopyrite and bornite, and is associated principally with pyrite and magnetite. The daminant alteration products are hydrothermal biotite and potash feldspar. Gypsum, anhydrite, garnet, chlorite and carbonate are commonly associated with sulphide minerals. Copper oxides, al-though present, are quantitatively of minor importance. The distribution of certain of the primary minerals reveals hypogene zoning characteristics.The results of stream sediment surveys, and airborne magnetic, ground magnetic and induced polarization surveys show important relationships to geologic structure and mineral deposits."

Jan 1, 1966

The Anglo Platinum Mogalakwena North concentrator was one of the first three hard rock mineral processing applications to utilise a HPGR circuit in preference to a SAG milling circuit. This was driven by the extreme competence of the ore that had given rise to throughput issues on the original South Plant. Despite more than adequate capacity and performance of the individual comminution units, the circuit has struggled to obtain full design capacity. A thorough review of the integrated performance of the circuit revealed a wide range of bottlenecks and underutilised parts of the circuit arising from design issues. Interestingly, the major opportunities lie in materials handling issues and mismatch of loads about the circuit. This paper presents the high-level outcomes and the associated opportunities, and is pertinent to all HPGR circuit designs.

Jan 1, 2012

By Bryon Bisiaux, Walter Valery, Sonny Mwansa, George Amonoo, Adrian Dance

"Newmont Ghana Gold Limited’s Ahafo operation have been working with Metso Process Technology & Innovation (PTI) since early 2009 to increase mill throughput from a combination of controlled blasting practices and optimised primary crusher and grinding circuit conditions. For such Mineto-Mill projects, PTI’s methodology is termed Process Integration & Optimisation (PIO).Ahafo operate a SAG mill, ball mill and pebble crusher (SABC) circuit that processes a range of primary ore of varying hardness from different pits which is blended with soft oxide material. The PTI study focussed on ball mill limited material from the Apensu open pit.Following a benchmarking study of all blasting, crushing and grinding practices in January 2009, PTI recommended changes in both blasting and crushing conditions in order to generate a finer feed size to the SAG mill. Additional operating changes in the grinding circuit were recommended.A series of trials were conducted in November 2009 where three blasts were fired using a different blast design (hole diameter and explosive type) in the same area of the Apensu pit as the benchmarked material in January 2009. Top and bottom benches (or flitches) from each blast were sent exclusively to the grinding circuit and the material was tracked using PTI’s SmartTag™ system.The results from the six trials showed a significant increase in primary ore throughput at a reduced blend of oxide material. Ahafo have since standardised on these modified blasting conditions for all Apensu ore zones and have been able to sustain higher throughput compared to historical performance on similar material.This paper summarises the phases of the PIO project, the changes made in operating practices and the outcomes of the blasting trials that validated the predicted increase in mill throughput."

Jan 1, 2012

By D. Krippner, C. Nexhip, D. George-Kennedy, P. Gebski, R. Kaur, W. L. Ying

ABSTRACT Water-Cooled Tapblocks Are Essential Components Of Modern Smelting Furnaces. Uninterrupted Operation Of A Tapblock Is Critical For The Optimal Operation Of A Furnace. This Critical Function, Together With Exposure To Extreme Conditions, Drives The Need For An Efficient And Reliable Means For Tapblock Monitoring. The Main Objective Of Tapblock Monitoring Is To Help Optimize The Life Of The Tapblocks By Better Scheduling Inner Refractory Relining And Protecting Operators By Preventing Sudden Deterioration Of The Tapblock. A Taphole Acoustic Monitoring (TAM) System Was Developed To Meet The Above Requirements. This Paper Describes The Principles Of The TAM System And Selected Case Studies.

Jan 1, 2013

By Ahmad Ghahreman, Denver Cowan, Yeonuk Choi

"Previous testwork by the authors has indicated that both granular coconut shell based activated carbon and a new microporous carbonaceous bead, Lewatit® AF 5, are highly effective in improving the oxidation kinetics and decreasing the elemental sulphur yield when assisting the atmospheric oxidation of pyrite. While the two carbon catalysts show similar results and improvements to the pyrite oxidation, there are differences between them. For example, the activated carbon assisted oxidation showed faster kinetics than the AF 5 assisted oxidation, while elemental sulphur seemed to remain adhered to the surface of the AF 5 after oxidation when much of the elemental sulphur formed during the activated carbon assisted tests was found in the oxidation residue. The objective of this paper is to investigate the differences between the two catalysts through the use of scanning electron microscopy, photography, Raman spectroscopy, surface chemistry analysis, and Brunauer-Emmett-Teller (BET) surface area analysis. With this investigation the authors should be able to achieve a better understanding of the surface chemistry of the two carbon catalysts (i.e. functional groups, charges, acidity etc.) and help explain the strengths and/or the weaknesses of the catalysts when applied to the atmospheric oxidation of pyrite.INTRODUCTION Previous research conducted by the authors, indicated that both a granular coconut shell based activated carbon (activated carbon) and a microporous carbonaceous bead, Lewatit® AF 5 (AF 5), acting as a catalyst enhanced atmospheric pyrite oxidation in ferric sulphate media by approximately 40% when compared to unassisted oxidation and that elemental sulphur yields were increased from 23% to approximately 69 and 63% when assisted by AF 5 and activated carbon respectively (Cowan, Jahromi, & Ghahreman, 2017). The study indicated that although total pyrite oxidation assisted by the two catalysts was similar, differences were noticed in the impact that the two catalysts had on the outcome of the oxidation. Kinetic curves in the Cowan et al. study indicated that atmospheric oxidation of pyrite seemed to reach completion after 48 hours of oxidation when assisted by activated carbon. A similar trend was noticed in the kinetic curves for oxidation when assisted by AF 5, however the oxidation curve did not reach completion until approximately 96 hours (Cowan et al., 2017). This observation indicated that the kinetics of pyrite oxidation are enhanced by both catalysts, oxidation kinetics are much faster when assisted by activated carbon rather than AF 5."

Jan 1, 2017

By Sammy Bansah, Komla Dzigbodi-Adjimah

Abstract-Ghana, a major West African gold-producing country, took a crucial step in 1986 to allow private participation in mining ventures that had hitherto been state controlled and starved of funds. This decision has led to a three-fold rise in gold production with substantial local and foreign capital once again flowing into exploration and mining projects. Though the rise in gold export is due primarily to increased production from large mines such as Ashanti Goldfields Corporation, Billiton Bogosu Gold, Tebrebie Goldfields and Ghana Australia Gold that work primary lode gold deposits on quartz veins and Banket conglomerates, a fair amount of gold comes from placer gold mining from which two new mines have been developed at Kwabeng and Bonte during the current gold boom. Also, placer gold mining is important locally because the lower capital outlay required for its development enables many entrepreneurs to operate small concessions and provide employment for a large pool of unskilled labor. Placer gold exploration and development in Ghana is labor-intensive. Pitting is the most used method although few employ the mechanized ("Banka") drilling. The advantages and disadvantages of the two approaches in the local setting are discussed. The gravel is normally sluiced and the gold recovered by amalgamation. The drawbacks to successful placer gold exploration in Ghana have been attributed to lapses in execution of exploration programs (Dzigbodi- Adjimah and Arhin, 1993; Dzigbodi-Adjimah and Gawu, 1994). However, the failure to recognize and set time frameworks and financial limitations for the various stages of placer gold exploration have spelt the doom of some projects. It is critical that the characteristics of the placer gold deposit be determined by efficient and cost effective means. A planned exploration supported by adequate flow of funds saves costs and leads to success. This article discusses the current Ghanaian situation and presents proposals from case studies for planning and budgeting placer gold exploration programs for use in similar settings.

Jan 1, 1995

By Sammy Bansah, Komla Dzigbodi-Adjimah

Ghana, a major West African gold-producing country, took a crucial step in 1986 to allow private participation in mining ventures that had hitherto been state controlled and starved of funds. This decision has led to a three-fold rise in gold production with substantial local and foreign capital once again flowing into exploration and mining projects. Though the rise in gold export is due primarily to increased production from large mines such as Ashanti Goldfields Corporation, Billiton Bogosu Gold, Tebrebie Goldfields and Ghana Australia Gold that work primary lode gold deposits on quartz veins and Banket conglomerates, a fair amount of gold comes from placer gold mining from which two new mines have been developed at Kwabeng and Bonte during the current gold boom. Also, placer gold mining is important locally because the lower capital outlay required for its development enables many entrepreneurs to operate small concessions and provide employment for a large pool of unskilled labor. Placer gold exploration and development in Ghana is labor-intensive. Pitting is the most used method although few employ the mechanized (“Banka”) drilling. The advantages and disadvantages of the two approaches in the local setting are discussed. The gravel is normally sluiced and the gold recovered by amalgamation. The drawbacks to successful placer gold exploration in Ghana have been attributed to lapses in execution of exploration programs (Dzigbodi-Adjimah and Arhin, 1993; Dzigbodi-Adjimah and Gawu, 1994). However, the failure to recognize and set time frameworks and financial limitations for the various stages of placer gold exploration have spelt the doom of some projects. It is critical that the characteristics of the placer gold deposit be determined by efficient and cost effective means. A planned exploration supported by adequate flow of funds saves costs and leads to success. This article discusses the current Ghanaian situation and presents proposals from case studies for planning and budgeting placer gold exploration pro-grams for use in similar settings.

Jan 1, 1995

By G. V. Fernandez

Sociedad Minera Cerro Verde S.A.A leaches secondary copper sulfides. In recent years, the mine has introduced innovations that have improved the management of mineral crushing, agglomeration, curing, and leaching. The crushing plant, for example, uses the concepts of degree of balance and percentage of time in an operationally balanced state which, displayed in real time, facilitate more intensive and uniform utilization of the crushers. High agglomerate quality is ensured with the correct dose of moisture, which is adjusted to the changing characteristics of the mineral through the use of electrical conductivity measurements. The amount of acid used for curing the agglomerate is also adjusted by using quality control information. Finally, the stockpile irrigation regime is managed using the criteria established by the "Lixiviant Request Rate", which optimizes the addition of leaching solution, creating such benefits as faster recovery, and reduced acid and energy consumption.

Jan 1, 2007