Search Documents

By P. Toscano

The objective of this investigation was to determine how the losses of nickel, copper and cobalt in fayalite slags could be controlled for nickel mattes with iron contents below 5 wt%. Laboratory-converting and slag-cleaning experiments were carried out at 1250°C. Several variables were investigated during and after converting to help minimize the amount of nickel and cobalt that reports to the slag. The variables used were oxygen concentration in the blast, coke breeze addition and nitrogen injection stirring. In all the experiments, slag and matte co-existed. Coke additions during converting have little effect on the losses of nickel, copper and cobalt. In fact, coke additions retard the converting process by consuming some of the oxygen injected. On the other hand, coke additions and nitrogen injection applied after converting was completed resulted in decreased slag losses.

Jan 1, 2004

By P. Toscano, T. A. Utigard

"The objective of this investigation was to determine how the losses of nickel, copper and cobalt in fayalite slags could be controlled for nickel mattes with iron contents below 5 wt%. Laboratory-converting and slag-cleaning experiments were carried out at 1250°C.Several variables were investigated during and after converting to help minimize the amount of nickel and cobalt that reports to the slag. The variables used were oxygen concentration in the blast, coke breeze addition and nitrogen injection stirring. In all the experiments, slag and matte co-existed.Coke additions during converting have little effect on the losses of nickel, copper and cobalt. In fact, coke additions retard the converting process by consuming some of the oxygen injected. On the other hand, coke additions and nitrogen injection applied after converting was completed resulted in decreased slag losses."

Jan 1, 2004

By C. A. Olivier

Le Ministère des Richesses naturelles du Québec has continued development work on the process/or direct reaction 0/sodium carbonate with lithium-bearing silicates(Canadian Patent No. 643,843). Recent process improvements have involved continuous pressure leaching, rather than batch leaching, and higher solution concentrations (over 55 g/l Li2CO3. These improvements have been demonstrated on a pilot scale operating on decrepitated spodumene from the Sullivan Mining Group's Quebec deposit. The new process is expected to be very competitive with the conventional sulphuric acid route. The improved flowsheet and main process steps will be described along with pilot-plant results.

Jan 1, 1979

By Dr. G. R. Hoey

"Abrasive wear and corrosive wear of carbon-steel grinding balls occurred simultaneously during the wet-grinding of hematite iron ore, and Ni-Cu sulphide ore, in laboratory ball mills. Two corrosion control methods, the use of corrosion inhibitors and pH control, were investigated and found to be effective means of reducing or preventing corrosive wear. Up to 50 % reduction of total ball wear resulted from the use of these methods.Corrosive wear is caused principally by the reaction of oxygen in air with the carbon-steel grinding balls, probably by the following reaction: 2Fe + O2 + 2H20 - 2Fe2 + 40H-.IntroductionA survey of corrosion problems in Canadian sulphide ore mines was completed and the findings were published in 197l(l). The corrosion survey was used to develop the present research program with the objective to find more economical and effective ways and means to reduce the corrosion that occurs in the mining and metallurgical industry. The purpose of this presentation is to review the projects being done by staff members of the Corrosion Section, Extraction Metallurgy Division, on corrosive wear and its control in wet-grind ball mills.Both abrasion and corrosion contribute to metal consumption during wet grinding of ores. The total wear of grinding media in this study is assumed to be equal to the sum of corrosive wear and abrasive wear. A great deal of research and development has been reported in the literature on ways to improve the abrasion resistance of grinding media but only a small number of studies has been reported on the corrosion resistance of conventional grinding media."

Jan 1, 1974

By S. Frimpong

Hydraulic shovels are widely used for primary production in surface mining operations. Variability in material diggability, unstructured mining environments and limited space and operator inefficiency affect the performance of these shovel excavators. Dynamic models of the hydraulic shovels are essential for understanding and improving machine performance. This paper contributes to this subject area by advancing hydraulic shovel kinematics and dynamics using the modified Newton-Euler method. A virtual simulator is developed to simulate the hydraulic shovel performance in the ADAMS environment. The simulator is validated with data on shovel geometry and the physical and mechanical properties of a formation in a surface mining environment. The results indicate that a shorter digging time increases the shovel operating power requirements, and that the required peak power increases by 100% when the digging time reduces by 50%. Simulation results also show that a shallow trajectory facilitates the digging process, with 50% reduction in peak power requirements compared to a deep one. This simulator provides a powerful tool for performance monitoring, excavation process designs and structural optimization of hydraulic excavators. This work also forms the basis for developing comprehensive simulator models for automated shovel operations in constrained mining environments.

Jan 1, 2005

By S. Surapunt, C. M. Nyamai, K. Itagaki

"The use of liquid copper as a medium for zinc extraction has been used in the Warner Process as a method of processing zinc-lead sulphide ore. The recovery of zinc metal is based on the reaction:ZnS(s) + 2Cu(l) = Zn(g) + Cu2S(l)In this method, thermodynamic and phase equilibria investigations of the Cu2S-FeS-ZnS and Cu2S-PbS-ZnS systems are of importance and form the basis for the liquid sulphide phase which appears as a product and is used as a solvent in the Warner Process. Phase relations in the Cu2S-FeS-ZnS and Cu2S-PbS-ZnS ternary systems were determined experimentally at 1473°K to provide a fundamental basis for the new zinc smelting process. The results show that the solid solubility of ZnS in the two systems is very small (2 wt% to 3 wt% ZnS in FeS, 4 wt% ZnS in Cu2S for the Cu2S-FeS-ZnS system; less than 0.5 wt% ZnS in both PbS and Cu2S for the Cu2S-PbS-ZnS system). The Raoultian Activity Coefficient of ZnS in the liquid mixtures and the vapour pressure of zinc over the matte in both systems is relatively large (?° = 7.7 – 15.8, Pzn(atm) = 0.088 – 1.026 for the Cu2S-FeS-ZnS system; ?° = 8.9 – 12.9, PZn(atm) = 0.075 – 0.214 for the Cu2S-PbS-ZnS system). On the FeS-ZnS join, the only phases detected are FeS and iron-rich sphalerite (Zn, Fe)S. The binary join mixture occurs at about 92 wt% FeS-8 wt% ZnS at 1473°K. Electron microprobe examination of the quenched samples indicate about 47 wt% to 48 wt% FeS in sphalerite and about 2 wt% to 3 wt% ZnS in the iron sulphide phase. On the Cu2S-ZnS join, microprobe analysis reveals that the maximum solubility is 4 wt% Zn in liquid Cu2S and 3.6 wt% Cu in solid ZnS. In the Cu2S-PbS-ZnS ternary system, microprobe analysis of the quenched samples indicate on average, 5 wt% ZnS in the liquid phase region. The only phases detected on the PbS- ZnS join are ZnS and PbS. The eutectic phase contains, on average, 13 wt% ZnS. The phase relationships, very low solid solubilities of zinc sulphide in the liquid mixtures of both Cu2S-FeS-ZnS and Cu2S-PbS-ZnS systems, coupled with the high Raoultian Activity Coefficient of ZnS as well as the high vapour pressure of zinc over matte all favour the partitioning of zinc metal into the vapour phase. This new process is cost effective and bypassesthe expensive and tedious conventionaltechnique of zinc production involving oxidationof the sulphide ore by roasting followed bya reduction process to extract the zinc. Theresults indicate that a new zinc smelting technologyusing the Warner Process would bemore efficient and preferable over the traditionalmethods of zinc extraction."

Jan 1, 2002

By O. M. Arafat, J. A. Finch

"The Functional Performance Equation calculated from a plant grinding survey defines two distinct ball mill circuit efficiencies and how they relate to total production rate through the target grind size. The survey data are also used to calculate a complete ball mill size distribution model, represented by the energy specific grinding rates, not just through the target grind size, but through all the size classes. Cyclone separation performance is represented by individual size recoveries to underflow. When these two unit operation performances are entered into the circuit modelling program (Streamline™), along with the circuit feed rate and size distribution, all the circuit survey size distributions and mass flows are perfectly regenerated by the program. The many issues associated with the historical Epstein (breakage-selection) models are eliminated. Once the circuit program is populated, pump and cyclone performance changes can be evaluated using a step-by-step procedure in order to maximize Classification System Efficiency. Mill water use and media sizing opportunities are also diagnosed in order to maximize Mill Grinding Efficiency at the size of interest. An example is provided. This circuit analysis and modelling system, and related training, is provided through a web-based application.IntroductionSince its development (McIvor, 1988), the Functional Performance Equation for ball milling has facilitated new understanding of industrial circuit cause and effect relationships, leading to significant strides in operational performance. Success stories of this refreshing approach to plant circuit performance improvement are now too numerous to list. Finch and McIvor (circa 1986) also discovered that the Functional Performance “Mill Grinding Rate” at the size of interest was the same cumulative grinding rate that is calculated from mill feed and discharge size distributions using a first-order rate equation. By calculating these cumulative grinding rates for all screen sizes, a complete ball mill model is generated (as used by Finch and Ramirez, 1981). Others in industry, Hinde and Kalala (2009), for example, have noted the same. Lacking the complexity needed to maintain their interest, most researchers have ignored this model, broadly opting instead for Epstein’s (1948) characterization of grinding as a chemical reaction, combining “selection rate” and “breakage size distribution” functions. The much simpler ball mill model presented here has previously been incorporated into a proprietary circuit modeling program (McIvor, 2005) and used for plant improvement work (for example, see McIvor and Finch, 2007, and McIvor, 2014). Now, by combining this extremely business-friendly ball mill model with optimization criteria from Functional Performance Analysis, a circuit modeling system (including the needed supplementary steps to assure successful plant implementation of circuit design changes) is at the disposal of every plant metallurgist, grinding equipment/material provider, and circuit designer."

Jan 1, 2017

By S. Dessureault, J. Porter, M. Woodhall

Information and communication technology (ICT) is seen as a key source of future productivity improvements in mines. The information technology infrastructure (ITI) necessary to achieve these productivity improvements will come in the form of data integrated from multiple source systems throughout the mining value chain. Two pure approaches are available: supplier-controlled or operations controlled data structures; each strategy has its own advantages and disadvantages. Case studies involving the South African mining industry are used to demonstrate the advantages of using hybrid-controlled data structures. Depending on the level of operational control, new skills are also necessary to be learnt by mining professionals including: information engineering; creating consistent and quality data; and process improvement techniques that use the integrated data for improving the operation.

Jan 1, 2004

By Tim Hughes, A. H. (Sandy) Gray, Jennifer Abols

"The selective recovery of gold and silver from solutions containing other metals such as copper is possible using AuRIX®100 resin in conjunction with the Gekko Resin Column. Selectivity is driven by controlling the solution pH, which enables activities such as loading copper, gold and silver and then selectively stripping copper before gold and silver. Alternatively gold and silver can be loaded and the copper left in solution. The selective loading of gold while reducing the silver loading has also been demonstrated opening the possibility of producing high grade gold doré from high grade silver pregnant leach solutions. This paper reviews the AuRIX®100 resin and Gekko Resin Column Technologies, discusses the uses of AuRIX®100 in the recovery of gold and silver and the chemistry relating to several projects for which AuRIX®100 is being tested.INTRODUCTIONGekko SystemsGekko Systems specializes in the design, development and distribution of innovative mineral processing equipment and systems with a particular focus on gravity separation for the gold and diamond industries. The company, which has been around since 1996, has five main products: the InLine Pressure Jig, the InLine Spinner, the InLine Leach Reactor (ILR), Gekko Resin Column and Modular Systems.The InLine Leach Reactor is an intensive cyanidation reactor that uses high cyanide (0.5 – 2 % NaCN) and high oxidant (20 ppm dissolved oxygen as O2 or hydrogen peroxide) to dissolve gold from medium and high-grade gravity or flotation concentrates. The ILR, which typically replaces a shaking table in the gold room, is available in both batch and continuous models. There are 42 installations worldwide. Further details on this technology can be found in papers written by Gray et al (2003) and Longley, McCallum and Katsikaros (2003). By replacing a shaking table with an ILR, the overall gravity and plant recoveries can be increased significantly. Other advantages include reduced security risks, lower operating costs, reduced operator involvement due to the automatic process and increased safety for gold room operators."

Jan 1, 2006

By G. A. Mallory

"The South Bay Division of Selco Mining is located fifty-four miles northeast of Ear Falls Ontario on Confederation Lake. The concentrator operates five days a week and processes six hundred tons per day of copper zinc silver sulphide ore. The concentrator is comprised of crushing, grinding, differential flotation, thickening and drying circuits. The major constituents of the concentrator feed are: chalcopyrite 7%, sphalerite 20%, pyrrhotite 3%, pyrite 25 - 30% and felsitic volcanics 40 - 50%. The mine went into production in March 1971 with an anticipated three year life and is now scheduled for closure in the summer of 1981. Recent mine production has been limited to three cut and fill stopes which have widely varying ore grades, therefore mill feeds vary from 0.25 to 4% copper, 3.5 to 27% zinc, 0 to 0.4% lead and 15 to 30% iron.In mid 1977 Selco negotiated a six month rental purchase agreement with Outokumpu Instruments Canada Limited for a five stream analyser system. The Minexan 202 probes were the first Outokumpu probe type analysers installed in Canada although Outokumpus' Courier systems are well known. Installation of the system took place in April 1978 and after numerous hardware faults the six month evaluation began in August. By December it was obvious that the Minexan 202 probes with proportional detectors did not have adequate resolution to determine low copper values in either of the tailings streams. Outokumpu offered to replace the tailings analysers with a new prototype solid state detector probe the following summer. The evaluation on the five Minexan 202 probes continued until August 1979 when the new solid probe was installed. The Minexan S (solid state) probe was evaluated with the three remaining Minexan 202 probes until December 1979 when Selco elected to purchase the system."

Jan 1, 1981

By A. Bamber

Canadian leadership in a global mining context will depend not only on entrepreneurship and best practice but also on technological innovation. This paper argues for more ambition and commitment to R&D for technological innovation in Canadian mining. It focuses on underground hardrock mining, where past R&D initiatives have simply not stood the test of time, and it is important to examine why. Concerns arise because industry’s commitment to R&D has not been sustained over time. Innovation through exploration, processing, and environmental technologies has been more significant. Meanwhile, R&D capacity and synergies in government institutions and universities have not been exploited. There is a need for more commitment, coordination, and collaboration by industry, governments, and universities. This paper examines some corporate models that have achieved sustainable innovation, along with some that have not. A strategy for innovation is discussed that relates to culture, commitment, coordination, and collaboration.

Jan 1, 2005

By John A. Herbst, Xiangjun Qiu

"Prediction of wear on a microscale level in mineral processing equipment turns out to be a challenging undertaking. This is particularly true for cases in which the objective is to use such predictions for wear parts design. The key to obtaining such predictions has turned out to be the use of physics based models along with phenomenological constitutive equations. In this paper, two components of the HFS tool set, one for particles (DEM) and one for slurry (MPF), are used for modeling. These tools are applied to the simulation of wear of SAG/AG shell lifters/plates and wear in slurry pumps. In each case wear predictions are validated with plant measurements.INTRODUCTIONHigh Fidelity Simulation (HFS) has emerged as an important tool set for mineral processing plant equipment design and optimization (Herbst and Potapov, 2003; Herbst and Nordell, 2002; Herbst and Lichter, 2006). This tool set consists of Discrete Element Modeling (DEM) of particle motion, Multi-Phase Flow (MPF) for liquid motion, discrete grain breakage (DGB) for particle fragmentation and discrete grain liberation (DGL) for mineral liberation (Campbell, Potapov and Tsuji, 1997; Ferzinger and Peric, 1997; Potapov and Campbell, 1996; Herbst and Potapov, 2005).Three sample snapshots of basic HFS illustrating the use of each of the various types of mineral processing equipment are shown below.Figure 1 shows a snapshot of a DEM simulation of ball charge motion in a commercial scale Vertimill. DEM simulation involves simultaneous solution of Newton’s Laws of Motion for 400,000 balls."

Jan 1, 2007

By Scott A. Stebbins

Cost evaluation models constructed specifically to evaluate the economic potential of an individually motorized railcar system of ore and waste transport demonstrate that the approach may be considerably more cost effective than traditional rubber-tired haulage methods. The system design places a motorized drive unit on each railcar, as opposed to the more common configuration in which a series of un-motorized cars trail behind a single locomotive. These motorized railcars are directed to various load and dump points by a computerized dispatch system, and as such have the advantage of operating unmanned. In addition, the tractive effort of the rail-type drive system is noticeably more efficient than that of the rubber-tired mode of transport. The savings are realized primarily through comparative reductions in the requirements for labor and, to a lesser degree, energy.

Nov 1, 2011

By Pablo González, Rodolfo Espinosa, Jose-Luis Noyola, Sergio Cossio

"Minera Penmont, at La Herradura, is a joint venture between Industrias Peñoles, S.A. de C.V., and Newmont Mining Corporation. The mine is located in the northern Mexican state of Sonora. La Herradura consists of an open pit mine with two-stage crushing and heap leaching facility, the gold is recovered from the pregnant solution using the Merrill-Crowe process; production began in July 1998. La Herradura produces about 130,000 gold ounces per year, and treatment capacity is 22,000 tonnes/day. Ore mineralization occurs in a shear zone with quartz and native gold. Gold distribution is quite heterogeneous due to the coarse visible gold, in some coarser particles ranging from 100 to 600 microns.Sampling and assaying protocols where established during exploration and prior to starting up operations, based on nomographs developed from early heterogeneity tests. But, as the coarse gold problem became noticeable, it was necessary to develop new sampling protocols to have an acceptable relative standard deviation to control the fundamental error within ± 15%.An experimental program was developed and conducted on a selected ore block made of 195 blastholes; regular ore grade control procedures were applied to both sets of data to evaluate the difference in results between the protocol established prior to starting up operations (“existing”) and the new protocol (“leaching”). In the “existing” protocol, subsampling is done through riffle splitters, and coning and quartering. Fire assaying is used to estimate the gold content, on a 50 g sample. In the “leaching” protocol a 12,000 g sample was bottle rolled cyanide leached, and the leach residue was assayed on a 50 g sample using fire assaying, and a weighted average total gold content was calculated. Currently, a new alternative method is being evaluated, where sub-sampling is done using rotary splitters, and fire assay on a 50 g sample; in this “rotary sampling” protocol and for comparison purposes, gold assays were also repeated using the “leaching” protocol.Test results were compared in three groups < 0.30 g/t (below cut-off), 0.30 to 0.8 g/t, and >0.8 g/t. Overall. Results show that the protocol established prior to starting up operations underestimates the gold assays. Detailed technical results, alternative options, and their implications are discussed in the paper."

Jan 1, 2003

By B. H. Kim

It is hypothesized that the standard approach adopted to characterize the ground and to determine the rock strength properties at depth are flawed and generally tend to underestimate the rock strength and possibly the stiffness, particularly when the rock mass is characterized as massive to moderately jointed or blocky to very blocky. It is therefore necessary to conclusively established that the hypothesis, that the rock strength in highly confined rocks is greater than generally anticipated, is actually valid and generally applicable, and then to develop new procedures to establish rock parameters that can be reliably used for the design of deep excavation.

May 1, 2009

By Chuck Edwards

"Milling operations in northern Saskatchewan’s Athabasca Basin have produced uranium continuously since 1975. Over that period, the Athabasca Basin has been one of the world’s premier uranium camps, yielding more than 660 million lb of U3O8. In this paper, the author describes former and current milling operations and discusses why and how the milling process has changed and developed over the past 35 years. The author’s considerations for the future of uranium extraction in the Athabasca Basin close out the paper.INTRODUCTIONThe roughly oval Athabasca Basin in northern Saskatchewan occupies nearly one third of the surface area of the Saskatchewan Shield. Its sandstone-like deposits lie unconformably on the older basement. The basin hosts many high-grade unconformity-type uranium deposits(Saskatchewan Energy and Resources, 2010) for which the Athabasca Basin is world famous. Uranium production in the Athabasca Basin has come from four mills. In the order of startup these are Rabbit Lake, Cluff Lake, Key Lake and McClean Lake. General data (AREVA, 2010; Cameco, 2010; Denison 2010) for each mill are shown in Table 1."

Jan 1, 2011

By P. J. Gron

"The Samatosum Project is a base and precious metal deposit located in south central British Columbia. A dilute ore reserve of 766, 682 tonnes grading an average 1.1% copper, 3.0% zinc, 1.4% lead, 833 gram per tonne silver and 1.6 gram per tonne gold is available. The base metals occur as tetrahedrite, chalcopyrite, sphalerite and galena. Virtually all of the silver and gold are associated with the tetrahedrite.The mill is operated at a rate of 21 tonnes per hour. Sulphur dioxide is used as a zinc depressant in the grinding circuit. Production of a Cu/Pb/Ag concentrate is accomplished by conventional flotation. This concentrate is then separated into Cu-Ag and Pb concentrates through a reverse flotation circuit utilizing sulphur dioxide, starch and sulphuric acid as lead depressants.The tailings from the Cu/Pb/Ag circuit are treated with copper sulphate to activate the zinc. Production of a zinc concentrate is accomplished by conventional flotation. Dewatering of the concentrates to 6% moisture is done with a LAROX filter press.Tailings effluent is treated with lime and sodium sulphide to precipitate out the heavy metals. The resulting sludge is treated in OYNASAND sand filtration units to produce a quality effluent."

Jan 1, 1990

By Carlos León, David Estrella, Javier Linares

"Recently, Antamina has completed an expansion program of its operations which increased the thoughput in grinding from acapacity of 109 to 130 ktpd. After commissioning, throughput could be exceeded in grinding and downstream processes but primary crushing became a major bottleneck to the overall production process.With an objective to increase the processing capacity of the primary crusher system, a multidisciplinary team was formed with members of Mine, Concentrator and Maintenance departments, who analyzed the overall context of this process restriction. The main implementations developed were: automatic discharge systems of trucks, logic to count trucks and elaboration of a daily performance report. Following implementation of developed improvements, the numbers of discharged trucks to crusher were increased from 449 to 614 units per day. As a result, the expansion target of 130 ktpd was exceeded and processing capacity was increased from 109 ktpd to 145 ktpd. This improvement adds very significant economical value for Antamina.INTRODUCTIONAntamina is a copper-zinc mine located in the Peruvian Andes. Compañía Minera Antamina is owned by BHP Billiton (33.75%), Xstrata (33.75%), Teck Cominco (22.5%), and Mitsubishi (10%). The mine was commissioned in 2001 with a capital investment of US$2.3 billion, and had a nominal 77,000 ktpd mill capacity. Mining, milling, flotation, and tailings impoundment take place at the mine site, which sits at an altitude of 4,300 m above sea level. The deposit is a polymetallic skarn ore body with intrusive phases of quartz-monzonite porphyry into Cretaceous aged limestone. Copper is present mainly as chalcopyrite with a minor bornite component. Zinc is present as sphalerite. Molybdenum is present as molybdenite. Some lead, bismuth, and silver are associated with the sulphides. The deposit is currently classified into six main ore types [Dechert, 2006], grouped into two categories: copper and copper-zinc. The mill produces four concentrate types: copper, molybdenum, zinc, and lead-bismuth. Copper and zinc, concentrates are transported by pipeline down to the port of Huarmey. Molybdenum and lead-bismuth concentrates are bagged and trucked to port."

Jan 1, 2013

By Paolo Toscano, Dave Hall

"This paper discusses the project history, process design and layout of the Rainy River Gold Project mill. The circuit consists of a 55 x 83 primary crusher, 15 MW SAG mill and 15 MW ball mill. Both mills are twin pinion with LSS and VFD drives. A pebble crusher is located in the process plant with bypass and stockpile options. Gravity concentration followed by 30 hours of leach residence, carousel CIP, carbon recovery, cyanide destruction and tails disposal in a 1,428 hectare tailings management area (TMA).The Rainy River Gold Project is located approximately 65 km northwest of Fort Frances in north western Ontario. The project is scheduled to be commissioned and reach commercial production in mid-2017. Expected cost is $US877M and is comprised of an open pit mine, process plant, tailings management area and supporting infrastructure. The process plant is designed to produce gold/silver Dore’ bars.The project has been developed on the following timeline:• 1967 – First exploration• 1994 – 17 zone discovered• 2004 – 433 Zone discovered• 2005 – Rainy River Resources Ltd. purchases property • 2006 - ODM zone discovered• 2007 - Cap Zone discovered• 2008 - First NI-43-101 Resource completed• 2012 - PEA completed & Intrepid Zone discovered• 2013 - New Gold acquires Rainy River Resources• 2014 - Updated feasibility study completed & Environmental Assessment report submitted• 2015 - Detailed Engineering >95% complete, EA approved and construction commencesThe property is accessed by provincial highway 600 and is within 17 km of 230 kV power line and railway sidings. Key project criteria are summarized as follows:"

Jan 1, 2016

By Timo Niitti, Antti Rinne, Janne Turunen, Sami Grönstrand

"This paper describes novel methods to enhance the flow dynamics of a mechanical flotation cell that can be applied to an existing installation. There are several reasons to alter the flow dynamics. The most common motivation is to improve the metallurgical performance of the cell, for instance, to improve the flotation recovery in particle size ranges that are normally difficult to recover.The flow dynamics enhancements are associated with the geometry of the rotor-stator area and additional features in the tank. The rotor-stator area has been modified to provide more concentrated turbulent kinetic energy or respectively more pumping efficiency with less attrition to the slurry. The tank can be fitted with various geometrical features, aimed to create a desired particle suspension profile. Depending on the targeted particle size range and application, badly selected or designed features can also have a negative effect on the metallurgical results.Besides new flotation equipment, the enhancements can be applied to existing flotation cell installations, thus enabling improvements in the mixing profiles, solids suspension, tank sanding and metallurgical performance of operating flotation circuits. Results of several tests carried out in existing plant operations are presented, concerning both flow variables and metallurgy.The common factor to above-mentioned enhancements is the use of modern computational fluid dynamics tools in the design phase, as well as the validation of the obtained CFD results in laboratory and production scale. Validated variables include mixing profile, power draw and local air hold-up.The paper demonstrates the effects of various flow geometries on the mixing profiles and metallurgical results of existing mechanical flotation cells. It shows how modern computational fluid dynamics analysis can be used to screen and select different approaches before carrying out costly trial-and-error experiments in plant scale."

Jan 1, 2006