Search Documents

In most instances, the preferred mining methods in steeply dipping narrow vein deposits are selective methods such as cut and fill or shrinkage. The main advantage of these methods lies in the higher degree of control over dilution that can be achieved. However, where ore body geometry lends itself to it, high yield bulk methods can also be attractive. Higher productivity (and the associated lower costs) and lower worker exposure are some of the significant advantages that have made such methods so popular. The Lapa gold mine located in North-Western Quebec uses the long hole mining method (with cemented rock fill) very successfully despite challenging ground conditions. This paper focuses on the experience of the mine with regards to drilling and blasting practices. Firstly, the reasons that prompted the selection of this mining method at Lapa are examined. Secondly, the challenges that the difficult ground conditions found at Lapa pose to drilling and blasting are discussed. Finally, the results of trials of different drilling and blasting strategies that were performed at the mine are presented with particular emphasis on the lessons learned.

Aug 1, 2013

By V. G. Papangelakis, S. Peters

Pressure oxidation of refractory gold ores can be conducted on ores with high carbonate content using just water or water with alkaline reagents to promote fast kinetics, and suppress the formation of elemental sulphur and CO2. In this work, a fundamental study was conducted to explore the silica-pyrite interaction in the presence of calcium and sodium carbonate. It was found that an alkaline environment increases the pyrite decomposition kinetics on one hand, but on the other dissolves silica, which encapsulates the dissolving pyrite thus hindering ultimately its complete decomposition.

Jan 1, 2011

By Jesus Garcia Iglesias, Jorge Loredo

"Abstract -The Asturian fluorspar district consists of vein and stratiform deposits where mineralization is controlled by a combination of lithological and tectonic factors.It is postulated that these fluorspar deposits have been formed under disequilibrium conditions created during circulation of ascending hydrothermal solutions along faults and other high permeability conduits. Mixing of solutions is inferred from fluid inclusion studies. Cavity filling and replacement processes are very important in localizing the ore deposits and in determining their morphology.Permian volcanic rocks in the area yield a regional positive geochemical anomaly in fluorine implying that Permian vulcanism may be a possible primary source of fluorine.On a regional scale a relationship can be established between some of the ore deposits and important tectonic lineaments. The stratiform deposits preferentially occur within a calcareous-detrital facies located at the margins of basins. These basin margins are related to important synsedimentary faults.Fluorite is the only economic mineral in these deposits. Quartz, carbonates, barite and pyrite are common minerals accompanying fluorite. Other minerals that may occasionally be present as minor components are: marcasite, chalcopyrite, fahlore, sphalerite, galena and related supergene minerals."

Jan 1, 1994

By Yves Gratton

The International Commission on Large Dams (ICOLD) is a non-governmental International Organization which provides a forum for the exchange of knowledge and experience in dam engineering. It is the world's leading professional organization dedicated to advancing the technology of dam engineering and supporting socially and environmentally responsible development and management of the world's water resources. ICOLD was founded in 1928 and has National Committees in 82 countries with approximately 7,000 individual members who are engineers, geologists and scientists from governmental and private organizations, consulting firms universities, laboratories and construction companies. Its original aim was to encourage progession in planning, design, construction, operation and maintenance of large dams and associated civil works by collecting and disseminating relevant information and by studying related technical questions. Since the late sixties, focus was put on subjects of current concern such as dam safety, monitoring of performance, reanalysis of older dams and spillways, effects of ageing and environmental impacts. More recently, additional subjects have included cost studies at the planning and construction stages, harnessing international rivers, information for the public at large, and financing.

May 1, 2002

By H. J. Chalmers

"Since the advent of large volume flotation machines, Cominco Ltd. has actively studied possible application of such machines to their various milling operations. A number of installations have been made and more are on the drawing board. This paper gives a description of these units, information as to choice of equipment, and information as to operating experience. Mechanical and operating details of six installations are summarized. Three different types of machines are discussed.Pine PointThe original Pine Point zinc flotation circuit comprised conventional roughing with two stages of cleaning. Over the years with increase in feed tonnage there have developed two adverse conditions; namely, a reduction in zinc concentrate grade coupled with an increase in MgO in the concentrate. This resulted in higher freight payments along with more severe smelter penalties. An intensive test program, in 1971, showed that the concentrate grade could be raised by 1.5 units of zinc along with a reduction in MgO from 0.8% to 0.47.. Subsequently this was done by adding two additional stages of cleaning using 16 cells of Denver 200-V's. The project was completed in January 1973 at a cost of $510,000 to give an estimated annual savings of about $390,000.Selection of the Denver Model 200-V was based on minimum floor space requirement, availability, and favourable operational and maintenance experience with Denver 100’s. As it happens it was possible to ""shoe-horn"" the 16 cells into place with a minimum of plant alteration. Some problems have been encountered with a tendency to ""sand up"" at high pH, particularly at the corners. Otherwise operational service has been very good."

Jan 1, 1974

By Samantha A. Beeson, Colin Poole

"A selective flocculation-floe flotation technique is already in use in the Canadian potash industry for the removal of water-insoluble slimes, but the process is currently limited in its application and reagent consumption is high. The work described in this paper details investigations into the separation of sylvite and halite from water-insoluble slimes by selective flocculation utilising other commercially available polymers.Preliminary flocculation performance tests were undertaken on pure sylvite, halite and water-insoluble minerals to establish the importance of a number of experimental parameters. The data from these single mineral tests was then used to establish optimum parameters for the separation of sylvite and halite from a synthetic mixture similar in composition to a typical potash ore. Under optimum conditions, separation was achieved with high recoveries using dispersant and flocculant dosages significantly lower than those currently used in plant practice.IntroductionAlthough solar evaporation and solution mining are used in some operations, most potash is extracted by conventional underground techniques and is then processed by froth flotation, in order to separate the valuable sylvite (KCI) from halite (NaCl) and water-insoluble gangue minerals. Flotation is usually preceded by a desliming stage to remove water-insoluble fines, but this also results in high potash losses and affects process brine requirements. To overcome these problems, one plant operated by Cominco in Saskatchewan uses a selective flocculation -floe flotation process (Banks, 1979/1980), in which a polyacrylamide flocculant is added to produce floes of water-insoluble material with minimal incorporation of halides. A collector is then added to render the floes hydrophobic and suitable for removal by froth flotation.A number of workers have also investigated the use of selective flocculation in potash processing, but these too have been concerned with developments in the removal of water-insoluble slimes (Williams, 1960; Brogiotti et al, 1974; Chan et al, 1986; Thompson et al, 1979; etc.). This paper provides results of novel investigations into the selective flocculation of sylvite and halite from water-insoluble minerals and discusses the possible mechanisms involved."

Jan 1, 1995

By S. Uddin

Microsegregation manifests its effect on microstructural evolution of cast or welded alloys which in turn influences their important mechanical and electro-chemical properties. In the above context, mathematical models of microsegregation have proven to play an important role in estimating the nature and predicting the effects of this phenomenon in wide varieties of solidification processes. Microsegregation models are useful in designing new commercial alloys, in estimating the homogenization time for the post-process heat treatments and in many other practical applications. In this study, two semi-analytical models of microsegregation were developed to predict the concentration field of solute in the liquid and solid regions for dendritic solidification of binary metallic alloys. Both models assume that the growing dendrites are cylindrical in shape. This assumption is more realistic compared to the common assumptions of plate like dendrites that most of the earlier researchers employed in their microsegregation modeling study. The solute redistribution profile, in the developing solid layer, necessary to determine the back diffusion parameter was derived from Fick's second law for the model without coarsening. The application of this parameter in a wide range of conditions and the use of its basic form in the model with coarsening has been verified. The concept of coordinate transformation and enhancement of back-diffusion Fourier number were used in deriving the model which took into account the coarsening of dendrites. The models are then extended to deal with rapid solidification and peritectic transformations and the results were compared with relevant experimental data for Aluminum and other alloys. A good agreement between model predictions and experimental results was found.

Jan 1, 2007

By M. M. Helm

Samples sourced from the Goldstrike property in Nevada USA, have been evaluated in terms of their preg-robbing capacity and the physical structure of the graphitic carbon component in the carbonaceous gold ore. The study highlights a wide range in preg-robbing capacity between samples collected from the Betze-Post open pit and Rodeo underground mine. The physical structure of the graphitic carbon was assessed using Raman spectroscopy, and is found to play an important role in influencing preg-robbing behaviour. Differences observed in the physical structure of graphitic carbon are thought to be the result of hydrothermal events that occurred at Goldstrike.

Jan 1, 2011

By C. H. G. Bushell, G. Brown, C. J. Krauss

1N FLOTATION, copper sulphate is used universally for the activation of sphalerite and marmatite and, to some extent, for the activation of other minerals. The copper activated surface readily adsorbs standard collectors such as the xanthates and dialkyl dithiophosphates whereas untreated zir~ sulphide does not. With the host of reagents available, making a mineral float is seldom difficult. The problem is to achieve selective flotation. In zinc flotation, the great value of copper sulphate results from its ability to activate zinc sulphide preferentially to gangue minerals. At the Sullivan Concentrator of The Consolidated Mining and Smelting Company of Canada Limited, the most abundant gangue mineral in the lead-zinc ore is pyrrhotite, and the zinc mineral is marmatite of somewhat variable zinc to iron ratio. For this Cominco study, selectivity between marmatite and pyrrhotite was therefore the most interesting aspect of copper sulphate activation.

Jan 1, 1961

By T. Crivits, I. Bellemans, V. Cnockaert, K. Verbeken

It is well known that slag foaming can significantly complicate copper smelting processes. This is especially true for unpredictable events that generate large amounts of slag foam during a small period of time. These events are here referred to as eruptions and are typical for certain types of liquid bath furnaces such as modern top submerged lance (TSL) furnaces. A few authors already made the link between over- oxidation of the slag phase and slag foaming. In this work, the mechanism is studied in more detail and explained using the smelter chemistry and the behaviour of dynamic foam formation. Finally, the most influential parameters on the foaming behaviour of the process are presented. INTRODUCTION Copper remains one of the most important metals used in our modern society. In 2017, the annual amount of copper produced worldwide was about 23.5 million metric tons. This makes copper the third most produced metal in the world after steel and aluminium. The majority of this copper was produced by copper smelting, about 19 million metric tons, both from primary concentrate and secondary feed material as reported in ICSG’s World Copper Factbook 2018. In the past, copper smelting was mainly performed using Flash smelting, a technology developed before 1949 (Kojo, Jokilaakso & Hanniala, 2000). Nowadays, this type of smelter is being complemented by other smelter types such as ISASMELT and Ausmelt technologies. These are two types op smelter furnaces, based on the concept of a top submerged lance (TSL) furnace. These two technologies were both commercialized around 1990 (Arthur & Hunt, 2005). It is estimated by Wang et al. (2016) that at this time, both flash and TSL smelters contribute equally to the total amount of annually smelted copper. Flash smelting stays the most important technology for extracting copper from primary sources. TSL furnaces, on the other hand, are more suited than Flash smelters for the recovery of copper from secondary materials. This is because of the different ways that the feed material is inserted in both furnaces. In Flash smelters, the ore and fluxes needs to be fine and completely dry in order to be able to blow the mixture inside the burner area of the furnace. The feed material for TSL smelters show less constrains concerning humidity and particle size. The material is dropped from the top inside the molten bath. As a result, a more complex and flexible feed stream can be processed using TSL smelting (Wood, Hoang & Hughes, 2017). This feature will become more important in the future as primary copper sources gets more scarce and the need for a fully sustainable material cycle increases.

Jan 1, 2019

By L. E. Djingheuzian

Introduction For many years the immense deposits of bituminous sands of northern Alberta have been attracting the attention of our governments, engineers and .scientists ( 6). Undoubtedly these bituminous sands represent one of the greatest potential resources of liquid fuels in the world. However, their commercial development has been retarded by the complexities of the technological problem and by the economic factors involved in the processing of the sands. The technological problem has been attacked from several angles ( 2, 3, 1, 11), and cold water separation of bitumen is one of them. To the ore dressing engineer, the cold water process is of utmost importance since, by the use of standard ore dressing machinery, it accomplishes most efficiently and economically the separation of bitumen from bituminous sands. The significance of using ore dressing equipment was especially enhanced by the fact that the scientific principles which underlie the design of standard machines were demonstrated in the cold water separation process with an extraordinary clarity. This greatly facilitated the analysing of limitations and advantages of different machines during-the pilot plant investigations and helped to complete the investigations practically in the allotted time.

Jan 1, 1952

By F. M. Doyle, G. Sidhu, A. J. Dussault, A. Raygani

There is a growing demand for rare earth metals for use in high strength permanent magnets, most notably Nd2Fe14B. Rare earth metals are extremely reactive, with reduction potentials around -2.5V SHE, and are conventionally produced by molten salt electrolysis. The current work was done to investigate an earlier report of electrodeposition of a neodymium ferroalloy from aqueous solution, to determine whether this approach could be an environmentally and economically competitive commercial approach for producing feedstock for permanent magnets. Such a process would be analogous thermodynamically to the Castner- Kellner process, in which aqueous sodium chloride brine is electrolyzed in cells with mercury cathodes. Metallic sodium forms an alloy (amalgam) at the cathode, thereby lowering the activity of the metallic sodium significantly below unity and making the reduction potential of sodium significantly less negative than the standard reduction potential. Here we report the effects of Nd/Fe ratio in the electrolyte, current density, temperature and two different complexing agents, glycine and cysteine, on the composition and morphology of the electrodeposits, along with current efficiency. The energy needed to produce neodymium as Nd:Fe alloys by aqueous electrodeposition was compared with values estimated for production by molten salt electrolysis and the thermodynamic energy requirement.

Jan 1, 2014

By C. A. Young, H-H. Huang, L. G. Twidwell

Equilibrium calculational software programs can be effectively utilized to model important parameters in aqueous and aqueous/solid systems, e.g., activity or concentration, solubility, temperature, solution pH, solution potential, and ligand complexation. In this regard, the calculational program ST ABCAL will be demonstrated. Illustrative examples for the creation of diagrams such as potential-pH, and activity or concentration-pH will be presented to demonstrate the fundamentals in real hydrometallurgical systems. Speciation, titration and mixing will be used to simulate or predict operational processes. Berkeley Pit water from a flooded abandoned copper open-pit mine will be used to illustrate the modeling process. According to analytical results the water contains about 20 important constituents. In addition to measured potential and dissolved oxygen, there are two distinctive oxidation/reduction couples. Concentration and other experimental parameters are seldom matched to each other and 12 different conditions have been identified. Water for each condition must be speciated in order to find the best-fit model. The STABCAL program will be used for the modeling calculations and the implication of the water chemistry to defining treatment opportunities will be discussed.

Jan 1, 2005

By J. H. Bernard, K. Zak

Abstract- The three traditional types of Variscan vein Pb-Zn-(Ag) mineralization recognized in the Bohemian massif from historic paragenetic studies are confirmed by modern metallogenic studies. Stable C, S, and 0 isotope data, as well as Pb and Sr isotopic ratios of the deposits, indicate a predominantly crustal origin of the constituents in all three types. Although the data also suggest differences in temperature and pressure of formation, and the oxidation conditions and nature of the hydrothermal fluids, nonetheless they are consistent with prevailing metallogenic classifications of the vein mineralization.

Jan 1, 1992

By I. I. Betcherman

INTRODUCTION A DISTILLATION process offers one of the most effective methods of refining metals. Its use is particularly attractive in the case of reactive metals which are not readily treated by pyrometallurgical or electrolytic methods. The 1ow vapour pressure of most metals severely restricts the applicability of the disti1lation process and only one or two metals may be effectively treated under atmospheric pressure at a reasonable temperature. If operations are carried out under reduced pressure several additional metals may be effectively distilled. Table I shows the vapour pressure of a number of metals together with a value of the free energy of formation of their ?oxides. Zinc and cadmium head the list and for many years? they have .been effectively refined by distillation. Sodium, magnesium, and calcium follow in descending order, and they may be distilled readily in vacuo and with difficulty at atmospheric pressure. Sodium, which is not of great metallurgical interest, is not considered. Magnesium has recently been produced in considerable tonnages by distillation methods ( 3). This paper describes the vacuum distillation of magnesium and calcium, their separation from each other, and their separation from less volatile impurities.

Jan 1, 1951

By L. B. Tsymbulov, N. A. Fedorova

The equilibrium of exchange reaction (Cu20)+[Ni]=(Ni0)+2[Cu] taking place in the course of interaction of metallic nickel-containing copper melts with different oxide melts (Cu20-NiO, Cu20-NiO-Si02, Cu20-NiO-FeO(Fe203)) in the area of their homogeneity has been studied. The studies, based on the known value of equilibrium constants and defined copper and nickel activity indices in metallic melts and equilibrium concentrations of Cu, Ni, Cu20 and NiO, determined the YNio/ycu2o ratios in the oxide melts of the above systems. For the equilibrium between nickel-containing copper and binary oxide melt Cu20-NiO, values of YNiO and Ycu2o were determined both by calculation and experimentally. Based of the data conclusions regarding oxide melts construction are presented.

Jan 1, 2007

By Michel Carreau

Renewable assets have large upfront capital costs but minimal operating expenses over their lifetimes. In some instances, deals can be structured so that direct capital investment is feasible, with paybacks typically within 5-7 years. In others, the burden of renewable CAPEX must be removed in order to create an attractive alternative to fossil-fuel-fired generation. Hatch has designed and oversees the construction of a renewable installation, which is financed, owned and operated by a special-purpose entity. Renewable energy is then delivered to the mining company via a customized power purchase agreement at a price that is lower than the levelized cost of fossil fuels. In this way, the mining company removes the burden of the renewable energy CAPEX from its balance sheet, thus freeing up capital, decreasing risk, and making the predictable, lower cost of renewable power more attractive than the variable cost of fossil fuels. This paper presents the above business model and success stories of hybrid power at remote sites (wind and solar coupled with diesel engine).

Aug 1, 2013

By J. C. Gathje

Newmont acquired the Phoenix Project through the acquisition of Battle Mountain Gold in 2000. Shortly after the acquisition, Newmont Metallurgical Services (NMS) and Nevada Operations began development work on a process to Pressure Oxidize (PDX) precious metal rich copper concentrates from Phoenix using the Lone Tree PDX facilities at Valmy, Nevada. The high precious metals content of the Phoenix concentrate - Au up to -300 g/t and especially Ag, up to -1700 g/t - led Newmont to the development of a High Temperature PDX process that achieves high cyanide leach recovery of Au and Ag, from the PDX solids, without the requirement for a messy and expensive "lime boil" or sulphate destruction process. Base metals content in Phoenix concentrates range from: 15-25 % for Cu, 1-10 % for Zn and 0-2 % for Pb. Excellent solution extraction of Cu and Zn is achieved while Pb is precipitated in the PDX residue. In addition to achieving high Au and Ag recovery this process produces very clean PDX discharge liquors that require minimum effort to remove contaminant metals and PDX solids that have superior settling and filtration characteristics. All of these factors contribute to lower capital and operating costs for the overall process. This paper describes the laboratory and PDX pilot plant developments for this process.

Jan 1, 2004

By T. Tsutsumi, S. Kukino

"During the diametrical compression test, the tensile stress generated near the loading plate is influenced by the contact area between the loading plates and specimen. However, very few studies have determined the contact area. Theoretical or analytical models have shown that for an orthotropic material (i.e., with material properties that differ along each of three mutually orthogonal twofold axes), the maximum tensile stress is generated at the center of disk when the angle of the principal material direction to the loading direction is close to ?/4. The maximum value is almost constant, regardless of the contact area. Conversely, the maximum tensile stress is generated near the loading plate when the angle between the principal material direction and loading direction is small. The maximum value decreases as the contact area increases. Therefore, in the latter case, the influence of the contact area on tensile strength measurement of is significant.In previous studies, the distribution of stresses applied on the loading plate is assumed to be a uniform load. In reality, the applied stress is highest at the center of loading plate and seems to decrease with distance from center. The applied load disappears at the edge of loading plates. In this study, in order to satisfy this boundary condition on the loading plate, the cosine curve is adopted as the distribution of load applied on the loading plates in a theoretical model of the diametrical compression test. Furthermore, the elastic solution using boundary conditions shown in this study is used to obtain the tensile stress distributions on the loading axis for an orthotropic circular plane. These distributions are compared with empirical results obtained under uniform loading with a loading plate or concentrated loading in previous studies."

Jan 1, 2015

Thermal barrier coating (TBC) systems provide thermal insulation to high temperature for aero¬propulsion. A fracture mechanical model developed earlier for multilayer systems is applied on TBC to realize superior performance by enhancement of fracture resistance. Functionally gradient materials (FGM) solution concept is the basis of approach followed here. A few realistic FGM TBCs are considered in the analysis in addition to a conventional TBC as the base case and a hypothetical worst case with YSZ-YSZ interface. Parameters like number, composition and thickness of graded layers and elastic modulus are considered for the analysis and quantitative improvement of fracture resistance of TBCs. The analysis is confined to deep crack with crack size to width ratio as 0.5.

Jan 1, 2010