Search Documents

By A. A. Brant

Self-potential methods are based ?on measurements on the surface of voltage distributions caused by natural sub-surface oxidation phenomena. The attempt is made to. correlate voltage minima or maxima with the location of mineral materials or geological conditions which may give rise to such naturally produced spontaneous potentials. Any orebody undergoing oxidation is a source of electric current. Ground waters carrying free oxygen attack the upper surface of the body, rendering this the positive pole of a galvanic cell, with the lower portion of the body the negative pole and the surrounding weak acidic waters the electrolyte. Current flow is from positive to negative through the orebody and negative to positive through the electrolyte, i.e., through the surrounding rock. The upper end of a steeply dipping, tabular orebody is hence indicated as lying below the point on the surface where the largest negative potential is observed(l). From its basis, it is apparent that the self-potential method was developed primarily for ore exploration.

Jan 1, 1942

By V. L. Eardley-Wilmot

Diatomite as prepared for the market is a fluffy, white powder, remarkably light in weight-it weighs only 10 to 15 pounds per cubic foot, or one-tenth as much as sand. Being extremely porous and inert, it is in large and increasing demand for insulation and filtration purposes, as general filler, and for many other uses. Structure Structurally, diatomite is quite different from any other known commercial material. It is composed of myriads of microscopically small, siliceous shells of diatoms which belong to a group of flowerless aquatic plants called algae. When these plants die, the siliceous remains sink to the bottom of the water and form beds of diatomite. Over 8,000 species of diatoms are known, named, and tabulated. The intricate scroll-work and patterns on many of these are one of the marvels of nature, and yet so small are they that from 40 to 70 million separate diatoms may be contained in one cubic inch of material. However, the size and shape of these diatoms, which vary greatly (compare Figures 5 and 6), have an important bearing on the commercial use of the diatomite. The diatoms in the majority of the known deposits are so typical of that deposit that, after a micro-examination, an expert can usually tell not only from what part of the world, but also from what particular deposit, the sample has come.

Jan 1, 1931

By X. -G. Chen, K. Liu, N. Parson

"Precipitation-strengthening 6xxx alloys are widely used for building and construction and automobile industries due to their high strength, good weldability and corrosion resistance. However, their elevated-temperature properties (250–300°C) decrease rapidly due to the fast-coarsening of precipitates. On the other hand, dispersoid-hardening is one of the most efficient approaches to improve the elevated-temperature properties. Therefore, the evolution of dispersoids during heat treatment in Al-Mg-Si-Mn alloys was investigated in the present work. Various heat treatments with temperatures ranging from 300–500°Cfor up to 24 hours were performed. Electrical conductivity and microhardness were measured while optical and scanning electron microscopy combined with image analysis, were used to characterize the dispersoids. Special emphasis was placed on the evolution of the size and number density of the dispersoids under different heat treatment parameters. It was found that dispersoids started to precipitate at 350°Cfor 1 hour. Nucleation and growth were the main mechanisms at temperatures up to 400°Cwhile coarsening occurred at temperatures above 450°C. The quantitative results indicated that dispersoids precipitation reached the optimum condition after treatment at 400°Cfor 2–4 hours with a fine size and high number density, resulting in the highest hardness.INTRODUCTIONThe precipitation-hardening 6xxx aluminum alloys with major alloying elements of Mg and Si are one of the most widely used aluminum alloys for building and construction and automobile industries (Dinaharan & Murugan, 2012). In recent years, there have been increasing demands for aluminum structural components to be used at elevated temperatures (250–300°C) for different applications. However, the mechanical properties of 6xxx alloys at elevated temperature are typically reduced due to the rapid coarsening of precipitates at 250–300°C. It has been reported that the yield strength (YS) of AA6061 in the peak-aged condition drops from 276 MPa at room temperature to only 30 MPa at 315°C(Kaufman, 1999). Therefore, it is a key concern to improve the elevated-temperature properties of 6xxx alloys to expand their range of applications."

Jan 1, 2018

By R. S. Forgan

The synthesis and study of a systematic series of phenolic oximes have shown that substitution in the 3-position can greatly affect extractive efficacy. Solid state, solution and gas phase analytical techniques, including X-ray crystallography, EPR and IR spectroscopy and collision induced dissociation mass spectrometry have been assessed for their applicability in interpreting the origins of differences in extractant strength. The dominant substituent effect on pH0.5 is the change in ligand pKa, with the more acidic ligands being stronger extractants. The influence of the 3-substituent on the stabilising intracomplex H-bonding of their copper(II) complexes also affects extractant strength. The 3-NO2 substituted ligand shows the lowest pH0.5 value, due to a combination of its low pKa and a stabilising bifurcated H-bond assembly around the copper(II) centre. Appending an aminomethyl group to the 3-position gives a ligand capable of binding a metal and its attendant anion. These metal salt reagents show potential to open up new flowsheets for the processing of high tenor copper feeds.

Jan 1, 2007

Introduction ?MT involves the measurement of naturally occurring magnetic and electric field oscillations. ?The ratio of E/H (wave impedance) is measured as a function of frequency to give resistivitydepth information. ?The ratio of vertical and horizontal magnetic fields (tipper) gives information about the location of (channeled) current systems.

May 1, 2008

By M. H. Leite, R. Corthésy, D. E. Gill

"La connaissance des contraintes naturelles qui prévalent dans les massifs rocheux est un prérequis indispensable pour la conception sécuritaire et économique des excavations comme on en retrouve dans les exploitations minières souterraines. Certains chercheurs se sont attardés à colliger les résultats de mesures de ces contraintes et les ont utilisés pour produire des modèles de prédiction basés sur leur traitement statistique. Ces modèles de prédiction sont très populaires auprès des exploitants miniers puisqu’ils permettent, du moins dans les étapes préliminaires de design, d’obtenir de façon s’apéconomique mais approximative, une partie des paramètres dont ils ont besoin. Dans le cadre d’un projet initié en 1994 avec la collaboration de l’IRSST, il a été décidé de produire un modèle de prédiction englobant une partie de la zone périphérique de la faille de Cadillac, soit une zone plus restreinte que le Bouclier Canadien utilisé jusqu’ici comme région pour l’élaboration de tels modèles. Pour produire ce modèle de nouvelles données obtenues avec une technique permettant d’exercer un excellent contrôle de qualité ont été ajoutées à celles déjà disponibles. Une telle régionalisation des données de base permet d’obtenir un modèle où les intensités et les orientations des contraintes principales sont beaucoup moins dispersées que ce que rapportent les modèles publiés jusqu’à ce jour. Enfin, il est démontré que le modèle proposé pour la région étudiée est en toute probabilité plus sécuritaire que les modèles plus généraux publiés à ce jour. Knowledge of the in situ state of stress existing in a rock mass is essential to the safe and economical design of underground mining excavations. Prediction models have been published, based on the statistical treatment of stress measurement results. Such prediction models are very popular among mine operators because they allow them, at least at a preliminary design stage, to economically obtain part of the information needed, even if this information is approximative. In 1994, a research project financed by IRSST was initiated aiming to produce a prediction model that would comprise a peripheral zone around the Cadillac fault. This region is more confined than the Canadian Shield on which the existing prediction models have been based up to now. In order to produce such a model, existing stress measurement results have been used in conjunction with new stress measurements that have been performed based on a technique which allows full control of the quality of the measurements. Restricting the data upon which the model is based to a more specific region gives a model in which the intensities and the orientations of principal stresses are far less scattered than the results published to date. Finally, it is shown that the proposed model is probably safer for the studied region than the models previously published."

Jan 1, 1998

By H. C. Rickaby

The Bannockburn gold area covers the four townships of Bannockburn, Argyle, Hincks, and Montrose, lying in the western part of the Matachewan district of Ontario (see Figure 1). The geology of these four town-ships was studied by H. C. Cooke of the Geological Survey, in 1917-18, and is shown in his map of the district. In the fall of 1930, a rich gold-bearing quartz vein was discovered in the northwest part of Bannockburn by B. S. Ashley. A prospecting rush followed the discovery; many claims were staked in the Bannockburn area, and, during the summer of 1931, a considerable amount of prospecting was done.

Jan 1, 1932

Over five decades ago Kitchener et al. in England and La Mer and Healy in the US were advancing our understanding and application of flocculants, primarily related to water treatment and filtration of sludge. This paper identifies the beneficial uses of flocculants in the mining industry and revisits some less common applications. Flocculants are used in unique ways in the mining industry: (a) to increase the effectiveness of sediment ponds to achieve discharge compliance; (b) to eliminate air emissions and costs associated with concentrate drying; (c) to reduce soil loss by applying a flocculant to erodible soils, and reducing wind and water erosion; (d) to remove/thicken metal precipitates in acid rock drainage treatment; and (e) to enhance clarification and thickening in mineral processing. The mechanism of how flocculants, coagulations and potentially-determining ions function is described and how their use can be controlled and optimized. The potential toxic effects of flocculants and coagulants when used to achieve effluent permit discharge compliance for suspended solids is discussed. A review of numerous best management practice (BMP) guidelines for the design and operation of sediment ponds treating mine site runoff to remove total suspended solids (TSS) and turbidity revealed an absence of a predictive methodology to address regulatory discharge compliance for TSS concentration, turbidity and flocculant-induced toxicity. An essential component of pond design is the need to determine whether flocculants and/or other settling aids are required based on the site-specific soil particle size distributions upslope of the pond. Procedures are provided to predict the need for settling aids and estimate pond discharge quality and downstream impact for TSS, turbidity, toxicity and sub-lethal toxicity. The need to develop BMP guidelines are discussed for (a) the application of flocculant to surface soils to reduce erosion, (b) the application of flocblocks to increase the ?sediment control? aspects of erosion and sediment control, as part of the mine site erosion control plan strategy and (c) the application of flocculant to silt socks to treat mine site runoff.

Aug 1, 2013

By Michael Samis

NOFLEX valuation results ? CF deviations and net CF risk discount factors ??Cash flow deviations indicate average cash flow variability. ??Net cash flow riskdiscount factors (NCFRDFs) indicate the size of the risk adjustment applied to a cash flow. NCFRDFs profile should change with variations in cash flow uncertainty since the risk adjustments applied to the project cash flow reflect investor sensitivity to uncertainty.?DCF and RO will often produce different NCFRDFs for the same project since they use different methods of risk-adjustment.

May 1, 2006

By S. Pinard, A. Desbiens, R. del Villar, D. Jakelski

"During the fall of 1993, a new Pill-based control strategy was installed in the B grinding circuit at the Kidd Creek Division of Falconbridge Ltd. The control strategy was first evaluated on a grinding circuit dynamic simulator (DYNAFRAG), which permitted the discrimination between more than a dozen possible control alternatives. Once the final choice was made the necessary instruments were purchased and installed. The control strategy was configured on the plant computer and is planned to be commissioned shortly.This paper summarizes the control strategy, the design procedure, the installation and the controller tuning. Some preliminary problems posed by the process prior to implementation are also presented.IntroductionIn 1990 the GRAIIM (french acronym for Research Group on Computer Applications to the Mineral Industry) of Laval University started a research project on Knowledge Based Automatic Control (KBAC). This project is sponsored by a consortium of eight mining companies under the umbrella ofMI1EC (Mining Technology Council of Canada), the Quebec Mining Association (AMQ), CANMET and the Centre de Recherches minerales (CRM). The project also benefits from important grants from the Ministere de l'Education Superieure et de la Science and the NSREC-CRD program.The main objective of this project is the screening of advanced (knowledge-based) methods for data processing (filtering, mass balancing, etc.) and automatic control (model-based control) for their use in the mineral processing operations. The project also aims at transferring these tools to the industrial partners through annual workshops for plant engineers, annual symposia, and through specific in-plant projects where the participation of plant engineers is strongly encouraged.The main objective of this project is the screening of advanced (knowledge-based) methods for data processing (filtering, mass balancing, etc.) and automatic control (model-based control) for their use in the mineral processing operations. The project also aims at transferring these tools to the industrial partners through annual workshops for plant engineers, annual symposia, and through specific in-plant projects where the participation of plant engineers is strongly encouraged."

Jan 1, 1994

By Dr. O. M Solandt

CANADA is not an old country we are just now planning to celebrate our lOOth Anniversary. Nonetheless, we have already developed some well-established traditions. One of the minor traditions is the standard speech on the need for more research and development in Canadian industry. I am sure that you have all listened to it many times -I certainly have given it more than once. Much as I am tempted to honour this tradition by repetition, I shall only give you a thumbnail sketch of the ancient address for the benefit of any unfortunate visitors who have not heard it before, and also to provide a base for some further ideas that I want to leave with you. Briefly, the traditional story is that, for a variety of historical and environmental reasons that I shall not attempt to describe in detail, research and development in Canada has grown up in a pattern that is ill adapted to foster the expansion of our manufacturing industries. The story continues by saying that research in the universities is of excellent quality but that we are very short of money to meet the expanding needs

Jan 1, 1965

By W. Standifird

"Cohesive fracture is a mechanical model widely used for modeling quasi-brittle fracture in rocklike materials. This work discusses use of this model to simulate quasi-brittle fractures generated by injection stimulation during the process of cuttings reinjection in West Africa. Cuttings reinjection is an engineering practice used for disposal of drilling waste. During this process, hydraulic fractures are created at the target formation and milled cuttings are injected with fluid. In practice, this process must remain in compliance with environmental regulations and zero-discharge policies. The purpose of this study is to determine the following factors of injection design for a field in West Africa: (1) pumping pressure capacity required to successfully perform the injection and (2) the injection rate for injection performance and the value of fracture width under injection.A simplified three-dimensional (3D) finite element model (FEM) was built. A poroelastic plastic damage model was used for simulation of the cohesive crack prorogation within the target formation. For simplicity, fracture development in both horizontal and vertical directions was simulated separately. In this way, the computational burden for one calculation was reduced to a reasonably low level, without losing accuracy of the model. Loads of the model include fluid injection and gravity, which balances the initial geostress field. Various values of injection rate were used in these calculations to determine the most reasonable value of injection pressure. The capacity of pressure of a pumping device was determined using this optimized value of injection pressure.Results in values of width and length of fractures created by the injection are presented. Injection pressures at bottom-hole (BHP) corresponding to each value of injection rate are also given. Numerical results for fracture generation and propagation in a horizontal direction were visualized. The pumping pressure capacity required to fulfill the cuttings reinjection work was determined based on the numerical results of optimized injection rates and pressure. The fracture width was determined using the given pumping pressure. The length and height of the fractures was determined using pumping pressure along with the required volume of cuttings waste to be disposed of into the formation.This work presents a case study of 3D finite element modeling of hydraulic fracturing generated by cuttings reinjection. The results of the optimized injection rate and pressure provide a best practice and a useful reference for cuttings reinjection analyses in this region."

Jan 1, 2015

By F. Y. Grepe

"THE MOST common type of mine hoist is, as is very well known, that in which the a.c. wound rotor motor is the driving medium. The reasons for the use of the wound rotor motor are, of course, economic. This type of equipment has, during the years, proved to be very reliable and reasonably satisfactory. It is, in fact, still being installed and in some places where a very hard and exacting duty cycle is demanded. As an example, a 600 h.p. 2,300-volt job was recently installed at the Caledonia mine (1) at Glace Bay. This is a vertical. hoist in a shaft only 175 feet deep but it is, nevertheless, working hard bringing coal to the surface and in making a trip at a speed somewhat better than every 20 seconds.The control equipment for such installations usually consists of a pair of primary reversing contactors which are interlocked both mechanically and electrically, together with some form of secondary controller. This, in the case of small hoists, can be a drum controller and metallic resistors or, in the case of larger hoists, a magnetic contactor panel and metallic resistors or, alternatively, can be one of the various forms of liquid rheostats which are available. The liquid rheostats, if of the dipper type, may be manually operated or it may be operated by some form of servo motor mechanism. In the weir type of liquid controller, the electrolite is, of course, pumped in and out of the rheostat."

Jan 1, 1954

By Vicken Aprahamian

"The Royal Canadian Mint (RCM) operates a gold and silver refining toll operation in Ottawa, Ontario, Canada. The silver refining line is a recent addition and was commissioned in 2005. One source of silver in the refinery is from gold doré which undergoes Miller chlorination before electrorefining to 99.99% cathode gold. Treatment of the Miller salt or silver-copper chloride produced consisted of a 2-stage high temperature reduction process step using soda ash prior to 2005. Copper-rich silver bars were produced and shipped offsite for further refining.The copper-rich bars could not be blended into sufficient high grade silver doré to dilute the copper and allow electrorefining in a silver nitrate medium. A new wet process was developed and commissioned to replace the high temperature reduction and allow removal of bulk copper. Thus upgraded impure silver produced was cast into anode for electrorefining to 99.9% purity silver flake. The 2005 RCM Hydromet Slag process is presented as well as its more current version. In addition, mention is made of a novel processing scenario for the introduction of Miller chlorination silver into the electrorefining circuit."

Jan 1, 2015

By B. Krysa, A. Mitsui, T. L. Koehler

The presence of arsenic, even at trace levels, in copper processing leads to the risk of arsine gas where reducing conditions exist that can reduce any soluble arsenic present to its minus 3 valance state and generate hydrogen gas from the solutions. This risk is understood to be significant within the industry, particularly in the case of liberator cells where copper concentrations in solution are drawn down to remove the copper and impurities from the bleed stream. However, there are numerous other potential areas where the arsine gas risk exists including contact between active metal such as iron, zinc or aluminum and arsenic bearing solutions in pyrometallurgical dust treatment, refining and acid plant operations. In turn this breaks down to different mitigating strategies dependent on the risk scenarios considered; for example, how this risk interacts with Change Management, Confined Space Entry or Contractor Training. The ISO 45001 is an emerging standard meant to improve employee safety, reduce workplace risks and create safer working conditions all over the world. The paper shows a case study of how a framework consistent with the tenets of ISO 45001 has been used to provide a consistent assessment of this risk for a wide variety of copper operations and the expectations of how this may be used to effectively improve the effectiveness of barriers against future incidents. INTRODUCTION Arsine gas (AsH3), first identified in 1775, is a highly poisonous, colorless, non-irritating gas with a mild garlic odor that is heavier than air. Arsine gas is generated when reducing conditions are generated in the presence of hydrogen ions and arsenic compounds. Present permissible occupational exposure limit as defined by Occupational Safety and Health Administration (OSHA) as an 8-hour time-weighted average is ppm (0.2 mg/m3). Further increasing the risk, conventional respiratory protection utilizing half or full masks with gas filtering cartridges provide minimal protection against arsine. In copper processing plants, the risk of arsine generation is well understood in liberator cells, which are part of the electrolysis process. In this process, solutions containing copper are reduced in copper concentration removing not only the copper, but also arsenic, antimony and bismuth. The residual solution can be bled to control impurity build-up in the refinery. In this process, if the copper concentration is reduced to the point where As3- can form, arsine gas is generated via reaction with hydrogen ions generated during the plating process. The copper concentration at which arsine gas is generated depends on copper concentration at the cathode surface, the temperature and the acidity. As a result, there is always a risk of arsine gas generation in the liberator cell. Process measures to minimize or mitigate arsine evolution are tight control on final copper concentration, warm temperatures, fresh feed distribution and internal acid recirculation rates. Operator exposure protection measures are hooding, ventilation, arsine detection systems, restricted personnel access, automated shutdown controls and pre-defined evacuation plans.

Jan 1, 2019

By S. N. Dixon

"Maximizing the value of each tonne of processed ore is the goal for all operations. Cyanidation processing of gold-copper ores has been challenging since its first use in 1889. The current practice treats a bleed or the total flow of mill solution to recover copper as copper sulfide (by sulfidization, acidification, recycling, and thickening), or to recover the cyanide (by acidification-volatilization neutralization). The process presented uses the adsorption of copper cyanide by carbon and the selective elution of copper from carbon to concentrate copper into a smaller stream. Copper contained in the smaller stream is precipitated as copper cyanide.RÉSUMÉ Toutes les exploitations ont pour objectif commun d’optimiser la valeur de chaque tonne de minerai traité. Depuis sa première utilisation en 1889, la méthode de traitement par cyanuration des minerais aurifère et cuprifère s’est révélée complexe. La pratique actuelle traite la saignée ou le débit total d’une solution de traitement du concentrateur pour récupérer le cuivre sous la forme de sulfure de cuivre (par sulfuration, acidification, recyclage et épaississement), ou pour récupérer le cyanure (par acidification, volatilisation et neutralisation). Le procédé présenté dans cet article utilise l’adsorption sur charbon actif de la solution de cyanure de cuivre et l’élution sélective du cuivre depuis le charbon pour concentrer le cuivre en un plus petit jet. Le cuivre contenu dans ce plus petit jet est précipité sous forme de cyanure de cuivre.INTRODUCTIONProcessing gold-copper ores by cyanidation has been a cost-control challenge since the cyanidation process was first used in 1889. Copper cyanide is stable only in the cuprous state, not the cupric. This factor results in the oxidation of a mole of cyanide per mole of nonchalcocite copper extracted. Each mole of copper extracted forms a cyanide complex with a minimum of 3 mol of cyanide. This cyanide-to-copper mole ratio is required to dissolve gold. The oxidation of cyanide and copper complexation with cyanide results in high cyanide consumption for copper-gold ores, which is a significant operating cost.One challenge in processing gold-copper ore is the cost of cyanide related to the extraction of copper. Processing 10,000 t/d of ore containing 1,000 mg/kg copper and 10% copper extraction yields 1,000 kg/d of copper. Currently, processes to remove copper from cyanide leach solution treat either the total flow of the barren or a bleed of the barren. The two processes used for copper-gold ores are sulfidization, acidification, recycling, and thickening (SART), which produces a copper sulfide product for sale; and acidification- volatilization-neutralization (AVR), which recovers the cyanide from a gas and produces a low–cyanide content solution. This low–cyanide content solution can be recycled to the process or might require additional treatment before being disposed from the operation."

Jan 1, 2017

By O. A. Ojo, O. A. Idowu, N. P. Wikstrom, M. C. Chaturvedi

Transient Liquid Phase Bonding (TLP) of a Nickel base superalloy, Inconel 738, was performed to study the influence of holding time, filler gap size, and temperature on the joint microstructure. Insufficient holding time for complete isothermal solidification of liquated insert caused formation of eutectic-type microconstituents along the joint centerline region. An increase in the eutectic thickness with increase in initial filler gap size was observed in joints prepared at a constant temperature and holding time. In agreement with prediction by conventional TLP diffusion models, an increase in bonding temperature for a constant gap size, resulted in decrease in the time, tf, required to form a eutectic-free joint by complete isothermal solidification. However, a significant deviation from these models was observed in specimens bonded at and above l 175°C. A reduction in isothermal solidification rate with increased temperature was observed in these specimens, such that a eutectic-free joint could not be achieved by holding for a time period that produced complete isothermal solidification at lower temperatures. Considerable enrichment of the liquated insert with base metal alloying elements at higher temperatures is suggested to be an important factor contributing to the observed departure from conventional TLP prediction.

Jan 1, 2006

By Brian K. Ayres

Inco Limited, Ontario Division is currently in the process of decommissioning the Whistle Mine site located near Sudbury, Ontario, Canada. The most significant component of site decommissioning involved relocating approximately 6.4 million tonnes of acid-generating waste rock to the open pit from two adjacent stockpiles. An engineered cover system was designed for the backfilled pit to reduce the long-term production of acid rock drainage. Geochemical modelling was conducted to assess the effectiveness of various cover options on the longterm water quality of the backfilled pit. Results obtained from performance monitoring of cover system field trials at the site and estimated full-scale construction costs were used to select an appropriate material for the cover system barrier layer. The two-dimensional soil-atmosphere model VADOSE/W was used to develop a calibrated model of covered waste rock based on field data obtained from the cover trials, which was subsequently used to predict net percolation and oxygen ingress through various cover system alternatives for site-specific climate conditions. Erosion and landform evolution numerical modelling was completed to assist in designing the runoff management system and final landform for the pit cover system. The potential impact of various physical, chemical and biological processes on the sustainable performance of the pit cover system was also considered in the design process. This paper provides an overview of the design and construction of the backfilled pit cover system.

Apr 1, 2005

By Dougal R. McCreath, Dwayne D. Tannant, Peter K. Kaiser

The Geomechanics Research Centre at Laurentian University in Sudbury, Canada, has undertaken a five-year research program into the design of support appropriate for control-ling damage caused by rockbursts. Rockburst damage mechanisms in Canadian hardrock mines are reviewed and a support design approach is presented. Each element in a sup-port system performs a reinforcing, holding, or retaining function. The desirable load-displacement characteristics for elements in burst-resistant support systems are described, and recommended support systems are presented for a spectrum of rockburst conditions ranging from minor to severe. A support system can be designed to (a) prevent the triggering of aground fall or a rockburst; (b) deform to accommodate the large imposed deformations arising from a rockburst; or (c) absorb the kinetic energy contained in ejected blocks of rock.

Jan 1, 1996

By P. -A. Bosse, J. Robitaille, P. Blatter

The LaRonde ore is a Cu-Zn-Pb ore with gold (3-4 g/t) and silver (60-100 g/t). The precious metals are recovered with copper concentrate, zinc concentrate and cyanidation of zinc tails via Merrill Crowe precipitation. Subsequent to a recent mill expansion, excessive gold was reporting to zinc concentrate with a concurrent decrease in gold to copper concentrate. Owing to the higher return obtained from the metal, the mill endeavors to recover additional gold and silver to the copper concentrate and minimize the placement of precious metals to the zinc concentrate. A gold deportment study showed that the gold occurs mainly as küstelite, with a moderate amount of electrum and a minor amount of native gold. It also showed that various sulfur-based Au-and/or Ag-bearing coatings on liberated küstelite and electrum were the major mineralogical factors that caused gold and silver to report to zinc concentrate. By frequency, such coatings were observed on 70-80% of total liberated gold particles reporting to the zinc concentrate. Based on the gold deportment and the chemistry of the coatings, the collector chemistry was reviewed and a new collector was added into the circuit which resulted in a significant increase in gold and silver recovery to the copper concentrate. The information obtained from the mineralogy confirmed and guided other process optimization. In this paper, the authors will describe the process mineralogy of the LaRonde ores, and in particular, the mineralogical evidence diagnosing the problem. Reference will also be made to the rationale behind how the problem was solved, the results achieved, and future steps in optimization.

Jan 1, 2005