Search Documents

By D. S. Speakman

The copper-zinc orebody at Sherritt Gordon's Ruttan Mine occurs in a structurally complex area of the Rusty Lake greenstone belt in northern Manitoba. Problems in interpreting drill results indicated a large deviation, and the structural complexity an erratic deviation, of drill holes. This was confirmed when a surface hole was intersected 420 feet to the left of line on the 800 level. This problem acted as a catalyst in promoting a search for a suitable down-hole survey method. The instruments investigated included magnetic multishot and gyroscopic units as well as the ABEM Reflex-Fotobor. Only the Fotobor came close to meeting the company's needs of simplicity, reliability, accuracy and ownership. In this paper, the methods of operating this instrument, as well as the data extraction and reduction techniques, are described. Data on the accuracy and repeatability of the instrument are presented, and a tabular presentation of the results of surveying on 86 holes totalling 64,000 feet of drilling is made. Preliminary statements of the results of ongoing research on causes of hole deviation are presented and recommendations for minimizing deviation are given. The use of the survey device is recommended in areas of structural complexity, for very steep or backsight holes and where expected ore intersections are missing.

Jan 1, 1978

By D. Vanin

"Conventional single heading track drifting in the hard rock mining industry has not shown any significant improvements in advance rates, despite the advent of modern track jumbos and igh speed muck handling systems .This paper presents Kiena 's experience in using a 7 ft 2 in. diameter larva Mark 6 Tunnel-Boring Machine (TBM) for driving 6000ft of drift.IntroductionKiena Gold Mines is located about 5 miles west of the town of Val d'Or, Quebec, approximately 300 miles north of Montreal. The mine commenced production in October 1981 and has gone through various expansions of ore production with 287 916 metric tonnes in 1982 to reach 453 800 metric tonnes in 1986.Due to the majority of claims being covered by a lake, a grassroots exploration drive of remote areas of the property was required to allow diamond drilling on a yearly basis. High speed sequential excavation methods (SEM) of single heading drifting in the mining industry has not progressed much in the past 20 years despite the advent of electric-hydraulic jumbos, Haggloader and Hagglund type cars. Certain examples of record SEM drifting advances have been performed in the past but only under very specific ground and cost conditions."

Jan 1, 1987

By L. B. Hale

"Introduction This paper will discuss the current operations of Westar Mining Ltd. and give a brief history of the company and of the Crowsnest Pass area. Westar is an integrated company involved in mining, processing and marketing coal from its mines in southeastern British Columbia and shipping coal from Westshore Terminals at Roberts Bank, located just south of Vancouver, B.C. It is two-thirds owned by the B.C. Resources Investment Corporation and one-third owned by the Mitsubishi Corporation of Japan and a consortium of Japanese coal consumers. Operations in southeast British Columbia consist of four coal mines and two processing facilities (Fig. 1). The Elkview Coal Processing Plant near Sparwood, B.C. receives its raw coal from Balmer operations (Harmer open pit), Balmer South (Panel 6) an underground hydraulic mine, and Balmer North an underground room-and-pillar mine. The fourth mine, Greenhills, an open-pit operation, is located near Elkford, B.C. and has its own processing plant. The Balmer mining and processing complex is the largest metallurgical coal facility in Canada producing up to 7 .5 million tonnes of clean coal per year. The Greenhills operation, completed in mid-1983, has a capacity of 2.8 million tonnes. The high-grade metallurgical and thermal coal produced is primarily for export markets. The major customers are Japan, Korea, Brazil, Pakistan, Chile and Taiwan.Our coal and that produced by other mines in Alberta and British Columbia is shipped to the international markets through Westshore Terminals Ltd., a wholly-owned subsidiary. Westshore will have an annual capacity of 22 million tonnes of coal and accommodate ships of up to 250,000 dead weight tonnes by 1984 when its current expansion program is completed."

Jan 1, 1985

By Ajit K. Sinha

"Abstract - Electromagnetic surveys were conducted over the Yava sandstone-hosted lead deposit in Nova Scotia to evaluate the usefulness of such surveys for detecting and mapping sedimentary­ hosted metallic ore deposits. Both transient and multifrequency systems were used for that purpose. The deposit consists of three zones of disseminated galena which also contain minor amounts of pyrite and sphalerite filling the interstices of the sandstone grains. Each zone overlies a basement depression and is separated from the adjacent zone by an intervening basement high. A conductive shale layer underlies the galena-rich sandstone formation at all three zones.Because the concentration of galena (3% to 4% ) and other sulfides is too low to affect the resistivity of the sandstone formations for detection by ground electromagnetic (EM) methods, the strategy for our survey was to look for areas of basement depressions and the presence of conductive shale in those depressions by EM depth soundings. The presence of the galena-rich sandstone formations could be inferred because of the close association of these two features with the deposits in the Yava area. Both transient and multifrequency EM systems were successful in mapping the basement depressions and detecting conductive shale at the three known mineralized zones. The technique, therefore, seems to offer good prospects for mapping similar stratabound sedimentary-hosted sulfide deposits."

Jan 1, 1993

By Ye Chen, Jianhua Chen, Xianhao Long, Qingxia Liu, Zhenghe Xu

"It is crucial to understand the mechanism of the collector interacting with the mineral surface in the presence of water molecules, which could influence the relaxation and electronic properties of sulphide mineral surface due to the proximity effect for narrow band gap of semiconductors. The adsorptions of three typical collector molecules (xanthate, dithiocarbamate and dithiophosphate) on the sulphide mineral surfaces in the absence and presence of water molecule have been simulated by density-functional theory (DFT). The calculated results show that the adsorptions of collectors on clean mineral surface in vacuum are not in agreement with the observed flotation behaviours. The presence of water molecules has a great influence on the adsorption of collectors. The analysis of density of states of the mineral surface atom suggests that the adsorption of water molecules could influence the electronic properties of mineral surface and consequently influence the adsorption between the surface and the collector molecule.INTRODUCTIONIn the separation of multi-metal sulphide ores, the selectivity of a collector is a key factor for the efficient recovery of the aimed mineral. Xanthate, dithiocarbamate (DTC) and dithiophosphate (DTP) are the most common collectors used in the flotation of sulfide minerals. Generally, xanthate exhibits powerful collecting property but lack of selectivity. While dithiophosphate and dithiocarbamate show the good selectivity in the lead and copper sulphide mineral flotation. The mechanisms of these collectors interacting with the sulphide mineral had been attracted many attentions and several mechanism based on experimental results had been reported (Chander & Fuerstenau, 1974; Fuerstenau, 1990; Raju & Forsling, 1991; Crozier, 1991; Bradshaw, Cruywagen & O’Connor, 1995; Guler, Hicyilmaz, Gokagac & Emekci, 2006). However, the micro-mechanisms of the selectivity of these three thiol collectors on different sulphide mineral surfaces are not fully understood."

Jan 1, 2016

By J. Gebhardt, D. McBride, C. R. Bennett, Croft. N., M. Cross

A comprehensive model of solution flow through heap leach systems requires a numerical solution with the ability to predict variably saturated-unsaturated flow through porous media domains that contain materials with spatially variable properties. The types of flow associated with stockpile leach processes lead to flow problems, such as infiltration into dry soil, drainage, perched water tables and flow through heterogeneous materials. Computational methods for modelling this class of flow behaviour are conventionally based on the classical Richards' equation. However, the governing equations are highly non-linear, difficult to solve, and require iterative numerical solution methods. The pressure-based form of the Richards' equation suffers from poor mass balance, while the mixed form can possess convergence difficulties. An adaptive transformed mixed algorithm is described, which reduces the non-linearity of the problem, optimizes the time step size, and provides a fast, numerically robust scheme that significantly reduces computation (or CPU) time. This method is shown to give fast, accurate solutions on a number of complex flow problems. The utility of this algorithm is illustrated through its implementation within the PHYSICA computational modelling software, which incidentally, provides a framework for a comprehensive heap leach model.

Jan 1, 2005

By R. P. Chapman

The geochemical interpretation of results of statistical analysis of published multi-element stream sediment data from southwest and northern New Brunswick is presented. Element concentrations in southwest New Brunswick are low and comparable to element concentrations in background areas in northern New Brunswick. Deposits of copper and nickel are indicated in southwest New Brunswick. Anomalous element concentrations occur in several areas in northern New Brunswick and the elements most commonly associated with these anomalies are Cu, Pb, Zn, As and Ag; and also Mo, Wand Sb. Bedrock geology greatly influences element concentrations and may cause false anomalies. Manganese has a pronounced effect on the dispersion patterns of Co and also Zn, Mo, Pb, As, Ba and Ni. Nickel and Cr are strongly sympathetically related and this association is independent of bedrock type.

Jan 1, 1977

By Kenneth Blower

This paper gives a detailed coverage of the ore flow through the primary crusher, cobbing plant and concentrator, including equipment sizes, recoveries, reagent consumptions and product descriptions. Special features, such as rubber chutes, rubber-lined mills, pebble-mill grinding, steam-hooded filters and process control instrumentation, are also discussed.

Jan 1, 1968

Building block cave operations involves significant commitments to capital and time before arriving at completion or full scale production. The focus of the mine planners is habitually to minimize the upfront capital and achieve target development rates and construction dates. However, management of the construction of block cave projects requires understanding of the strategic/tactical decisions that the project planners can take to increase the value of the project and cope with schedule risks. As block cave projects involve development of vertical and lateral access to the underground footprint and ore body, more attention to uncertainties is required as most of those projects need to confront delays leading to a decrease in value. The standard process of development and construction scheduling is often not planned with provisions to realise uncertainties in the construction phase. Uncertainties and risks such as poor ground conditions and equipment breakdowns are the primary reasons for schedule slippage. As a result most of these projects experience delays. In order to mitigate risk to the project schedule, we centre our attention on increasing the value of the project by spending more money upfront and improving the schedule rather than focus on minimizing the upfront capital. Scenario-based simulations along with project appraisal methods hold great promise to address those challenges and enable mine planners to make better decision and enhancing project value. This paper will present a hybrid simulation based approach to model the process of development and construction based on discrete event (DES) and continuous based simulations (CBS). Such simulations will be conducted for scheduling multiple development headings (Apex, undercut, extraction, and haulage levels). Two scenarios are utilized to investigate the impact of risks on schedule and how flexibility in construction can be incorporated to minimize delays: (1) The bench mark scenario is created based on actual data from an existing case study. (2) The flexible scenario is an alternative way to use primary production infrastructure (Ore Handling System) including conveyer drifts, conveyer belt, and a gyratory crusher in the construction process and that requires the system to be in place before starting lateral development in the footprint. As a result, a truck-load system versus a conveying system will be studied to observe the gain in construction speed and to estimate the premium cost for mucking rock from headings and drawbells and transporting it to surface. Such strategic flexibility would be part of the original budget to make the tactical flexibility available during construction. Continuous cash flow models are used to evaluate and compare the scenarios. This study is an example of how new techniques in planning can be used to support decision-making processes in block cave design.

Aug 1, 2013

Flotation works very well for particles that are typically in the range 20 to 150 µmin diameter, for base metal ores. In this range, it is possible to get quite high recoveries in conventional flotation machines. Outside this range, the recoveries decline progressively, whether it be with the very fine or the coarse end of the size spectrum. In this paper, the reasons for the drop-off in recovery are briefly reviewed, together with strategies for future work. Recent progress in the author's laboratory will be described. These include the Concorde Cell, which takes advantage of the high dissipation rates in the shock wave created when a gas-liquid mixture reaches supersonic velocities. The environment thus created is very beneficial for the flotation of ultrafines. For coarse particles, the reasons for the drop-off in recovery can be related to the highly turbulent nature of the pulp in a conventional flotation cell. To improve recovery, it is necessary to find a way of bringing particles and bubbles into contact in a quiescent environment. A new process for coarse particle flotation will be described, in which a fluidized bed is created in the flotation cell. The flow conditions are very gentle, and the high solids concentration leads to rapid rates of capture of the particles. Experimental results are presented. It is apparent that the maximum floatable size for coal and minerals can be increased by a factor often over the limits found in current practice. Advances

Jan 1, 2009

By Chandrakala Kari, Divyang Shah, Lakshmi Kanth Reddy, Kaushik Vakil, Sanjay Sarkar, Bhavin Desai

Gases rich in sulfur dioxide generated as a by-product of smelting and converting operations of copper concentrate contain selenium apart from zinc, lead, copper, cadmium, bismuth, antimony, and arsenic. The gaseous stream is heat exchanged in waste heat boiler, dust collected in electrostatic precipitator followed by cleaning in reverse jet scrubber to remove fumes, halogens and fine dust before passing to DCDA Monsanto catalytic converter to produce commercial grade sulfuric acid. The gas cleaning section of the acid plant uses water to scrub the smelting gases. During scrubbing, precipitated solids, known as sludge, settles at the bottom of the reverse jet scrubber containing 30 to 40 wt% copper and selenium up to 40 wt% selenium. In the existing process, the sludge collected during scrubber cleaning process is directly recycled to the smelter for copper recovery. However, the selenium is expected to again vaporize due to high oxidation potential during smelting and converting, causing accumulation of selenium in sludge. In present investigation, a roasting process has been developed to recover the selenium from acid plant sludge before charging it to smelter for copper recovery. Selenium is associated with copper in acid plant sludge as copper selenide, as determined by X-ray diffraction and electron microscopy. Thermodynamic and thermo-gravimetry study revealed that the copper selenide phase present in the sludge was amenable to oxidation at 600°C forming oxides of copper and selenium (Cu-Se-O). However, the dissociation of selenium from the copper oxide was made possible by sulfatation using sulfur dioxide between 450°C to 600°C, resulting into the formation of CuSO4(s) and SeO2(g). Lab scale experiments were carried out in vertical tubular furnace to determine the optimum roasting conditions with respect to roasting time, temperature and molar ratio of O2:SO2. Using these optimum conditions, selenium up to 90 wt. % in the form of SeO2 vapors could be recovered from the acid plant sludge in a large scale commercial roaster. Roasted sludge free from selenium and containing oxides and sulfates of copper could now be recycled in the smelter for copper recovery. INTRODUCTION There is an increasing demand for minor metals due to their use in innovative technologies. Similarly, the increase in demand for selenium is expected due to disruption in sectors related to renewable energy and photovoltaic battery. Selenium is a chalcogen and a non-metal with black or red crystalline appearance. Selenium is used in the glass industry to decolorize glass and to make red-colored glasses and enamels. It is also used in solar cells and as a photographic toner. Selenium is used as a brasses in stainless steel to improve its machinability. Selenium sulfide is used in anti-dandruff shampoos. In spite of the toxicity of its compounds, selenium is also an essential trace element for humans and animals. Selenium occasionally occurs free in nature, but more often occurs as selenides of iron, lead, silver and copper. There is an urgent need for the development of new methods for selenium recovery from the existing resources. Commercially, selenium is obtained only from anode mud produced during electrolytic refinery of copper.

Jan 1, 2019

By C. R. Julian

MECHANIZATION During the last fifteen years, numerous attempts have been made to mechanize the operations of loading ore and placing till. It is to be regretted that, to date, little progress has been made in this direction. The comparative efficiency of manual labour in Spain is the factor largely responsible for the failure to cheapen costs by mechanization. The necessity for careful classification of the ore and the need for keeping all openings small also makes the problem one of difficulty. It may be of interest to describe the various attempts at mechanization that have so far been made. CONVEYORS: (1) When stoping by layout III in San Dionisio, a trial was made of transporting the filling by jigging conveyors. This method proved un-economical, as the wall building and spreading of the till could not keep pace with the delivery, with the result that the machinery was idle a great part of the shift. (2) The transport of ore from the working places to the ore-passes by jigging conveyors and belts was also tried. Although more successful than in the case of the fill, the method could not compete with that of hand tramming, principally due to the high cost of (a) maintenance caused by the abrasiveness of pyrites, and (b) labour constantly employed on re-aligning the conveyors owing to the constant settlement of the floor. In a few cases, where a sill floor was being blocked out in virgin ground, the method showed a saving. SCRAPERS: Frequent attempts at loading by scrapers have been made, but again the only success obtained has been in the blocking-out of sill floors. The principal obstacle to the successful application of scraping, other than on the sill floor, has been that the openings, which have to be small, call for a light scraper outfit, whereas, in practice, a heavy scraper and at least a 25 h.p. winch are necessary for handling satisfactorily the ore, which is heavy and which breaks somewhat blockily.

Jan 1, 1940

By V. Songmene, A. Tahan, J. P. Michaud

The machining of thin wall parts, often used in the aeronautical industry still creates a number of problems, including panel deformation. Quality and productivity are often affected. This study seeks to determine the optimal conditions for cutting in order to guarantee a competitive fabrication of parts while still maintaining quality and delivery deadlines. The studied model (Spar) is a typical structural part used in the assembly of airplane wings. The main objective of this study was to improve two performance aspects: surface quality finish (quality criteria) and the rate of cutting by stock removal (economic criteria). To achieve this objective, we used an evaluation process of the geometrical error issuing from the machine-tool. We also determined the stability zones of the machine-tool's dynamic system. Finally, a series of high-speed machining tests (finishing cuts) were conducted using an experimental structured approach (16 000 - 24 000 rpm). Profile measures of surface roughness and cycle times registered during trials allowed us to establish optimal cutting conditions. Surface roughness improved as well as cutting by stock removal. Four parameters were taken into consideration: axial depth of cut, chip load, spindle speed, and cutting fluid. Finally, the influence of the type of cutting fluid was evaluated to show that it did not significantly affect machining results.

Jan 1, 2006

By B. Karnath, K. Guha, S. Tandon

At Jhagadia Copper Ltd (India), Copper is produced through secondary route using Top Blown Rotary Converter (Kaldo Furnace). The basic raw material being treated includes Matte-slag Reverts, Copper Cakes, dross & Cement, Oxide Ore, Low S bearing Concentrates & various metallics along with high grade copper scraps. The plant has capability to refine & produce Blister grade copper from Kaldo furnace as well as PS Converter . Blister is fire refined in Anode furnace & electro refined in Refinery to produce cathode copper. Our product , Copper Cathode , has already been established in the market as its quality is better than 'LME Gr'. The paper deals with the experiences encountered during commissioning & stabilization of the plant.

Jan 1, 2007

By K. Purazrang, P. Musavi Garavi, P. Sh. Naseri, P. Abachi

The fracture behavior of high strength Al7050 alloy was investigated at room and elevated temperatures using small size, V-notched tear (called Kahn specimen) and compact tension, CT, specimens, respectively.To study the elastic-plastic behavior of the alloy, the tensile test was also performed on the sub-sized cylindrical tension test specimen. The microstructure of the alloy was examined using optical- and scanning electron- microscopy. The rupture mechanisms and crack path were also studied by examination of specimens' fracture surfaces using SEM. The microstructure examination revealed equiaxed grains and some elongated grains in rolling direction, with the areas of partial re-crystallized grains where coarse intermetallic particles are mostly found.In general, fracture surfaces were indicative of dimpled ductile type. Considering the fractographs of tensile specimens, the void growth mechanism is also dominant in fracture of these specimens. Nevertheless, in some regions, smooth areas can be observed due to the friction during rupture process. The results of mechanical tests at RT made the evaluation of tear strength to 0.2 % tensile yield strength ratio, as a measure of notch toughness, available. According to elevated temperature, 150°C, test results and plots of log da/dt vs. log KI , the crack propagation behavior over discrete ranges of crack growth rates could be assumed linear and then be obeyed as a power law equation in the form of da/dt = A (KI)n .

Jan 1, 2015

Abstract-This paper discusses the fundamental question, "what is an adequate sample size?" in the light of recent developments regarding parameters of Gy’s well-known formula for predicting sampling variance. New understanding of the granulometric factor, g, and the liberation factor, l, had significant impact on the results of calculations involving Gy’s equation. For the granulometric factor, justifications are given as to why nominal comminution size should always be reported as P95 (i.e., the screen size rejecting 95% of the mass). A small but important change in the model to estimate the liberation factor makes the difference between a predictive formula that works or does not. Other parameters and considerations regarding their practical implementation are commented upon in light of the author’s experience.

Jan 1, 1998

Electric Vehicle Controllers Ltd. ?EVC started in 1981 ?Underground electric locomotive drive systems ?Developed tandem load sharing system and radio ELOS controls ?Locomotive autonomy systems ?Entered space technology development in 1999 with NORCAT to develop Mars drill for CSA ?Commercial distributor for drilling systems, lunar physical simulants, electric mobility systems and lunar mining technologies

May 1, 2009

According to the principle of similarity, the physical and chemical configurations of a system can be defined by ratios of magnitudes within the system and do not de-pend on the size or nature of units of measurement. In the present work, the similarity principle was utilized in evaluating the reducibility of various iron ores in a rotary batch furnace under optimum operating conditions. It was then used successfully to extrapolate the results, first to the operation of a 20-ft. pilot-plant kiln and then to an industrial-size 80-ft. kiln. By means of this systematic analysis of kiln operation, it was possible to increase the production capacity of the kiln considerably. T HE kilns used by the Strategic-Udy process for the partial reduction of iron ores are, in most aspects, similar to conventional calcining kilns. Iron ore is fed continuously in the upper (feed) end of the kiln and, as the latter rotates

Jan 1, 1964

By F. S. Hoseinian, M. Irannajad, M. Safari

In this study, the effect of chemical interactions of materials used in ion flotation on the removal of Ni(II) ions from low concentration synthetic wastewater was studied. Sodium dodecyl sulfate (SDS) and ethylhexadecyldimethylammonium bromide (EHDABr) as collectors and methyl isobutyl carbonyl (MIBC) and Dowfroth250 as frothers were used. To investigate the effective parameters and interactions of them, 16 experiments including 6 level variables were performed by supporting DX7 software and on the bases of 2-level factorial method. In the first step, the tests were conducted in a Hallimond tube. The result showed that collector of SDS and frother of Dowfroth 250 had appropriate interaction with each other at pH = 3. In the second step, optimal results from the first step were evaluated in a mechanical flotation cell. The removal of Ni(II) ions increased by increasing the time of flotation and they have a direct relation with the water removal. The kinetics study shows that the order and the rate of removal of the reaction do not follow any of the zero-order, first-order and second-order equations. The flotation rate curve on the removal of Ni(II) ions will divide the separation process to two stages, a fast flotation rate at the first stage and a slow flotation rate at the second stage. Ni(II) ions removal was obtained 88% at the best condition.This study showed that the use of ion flotation was a very effective method for Ni(II) ion removal from industrial wastewaters.

Jan 1, 2016

By Gonzalo Bernstein, David G. Meadows, German Naranjo, Edgardo Tapia

"During the last decade Antofagasta Minerals’ Los Pelambres Mine has dramatically increased its ore throughput following the fast initial phase ramp up through a series of planned incremental expansions. The original 85,000 mtpd, two SAG line plant was commissioned in 1999 and rapidly exceeded nameplate tonnage in only a few months. Following this, the inclusion of a pebble crushing circuit resulted in throughputs in excess of 114,000 mtpd and a recent, final third line SAG and ball mill addition have taken the plant to over 175,000 mtpd even with increasing ore hardness and changing ore feed characteristics. The progressive changes are described in this paper together with how the technical challenges have been met.INTRODUCTIONMinera Los Pelambres is a world class copper-molybdenum operation located in the Salamanca area in Chile, in region four, approximately 500 km north east of Santiago, the capital of Chile. In the late 1990s Antofagasta Minerals developed the Minera Los Pelambres project in Chile at an investment cost of approximately $1.3 billion USDs. The project construction was successfully led and completed by Bechtel Corporation in 1999 and within a matter of months the plant was already exceeding the nameplate capacity of 85,000 mtpd. In 2001 a pebble crushing circuit was added to raise the capacity to 114,000 mtpd. In the early part of 2003-2004, it was recognized that the hardness profile was changing with depth and that in order to maintain the plant capacity additional power would be needed in the SAG mills together with upgrading of the primary crusher. In conjunction with these changes a fifth ball mill and a second primary crusher station would also need to be installed. A further detailed engineering study and evaluation was initiated by Minera Los Pelambres. This was lead by Bechtel Corporation with major design contributions from FLSmidth and Siemens in order to establish the re-powering requirements for the SAG mills. These re-powering changes together with the inclusion of a pebble crushing circuit took the plant to up to 125,000 mtpd even with harder more competent ores. Finally in the last two years an additional grinding line has been added to take the capacity to consistently over 175,000 mtpd. The third line was installed in a record time of 256 days. A schematic of the current comminution circuit, discussed in this paper, is shown in Figure 2."

Jan 1, 2012