Search Documents

By D. J. Xue

Four kinds of coal-rock combination were subjected to three kinds of stress waves in the SHPB numerical simulation. The wave propagation and the changes of the strain energy in the coal-rock combination during the dynamic impact process were recorded as well as the contact force. The dynamic response law of coal-rock combination was obtained. It was found that the coal had better reflectivity than the rock because of coal with larger impedance. In contrast the rock had better transmissivity. As the crest value of the incident wave increased, the increment in the crest value of the transmitted wave weakened in the coal-coal group, coal-rock group and rock-coal group, in contrast, the increment in the rock-rock group increased.

Aug 1, 2013

By J. S. Laskowski

Anisotropic minerals are important constituents of many ores. This group includes both valuable minerals (e.g., molybdenite in Cu-Mo ores) as well as gangue minerals (e.g., talc in platinumbearing sulphide ores in South Africa, graphite in Cu-Ni sulphide ores in Canada, chrysotile in Ni sulphide ores in Australia, and clay minerals in all types of ores). Aqueous suspensions of anisotropic minerals exhibit different properties than suspensions of isotropic minerals. The presence of anisotropic minerals in flotation circuits affects the flotation process.

Jan 1, 2012

By R. M. Beauchamp

Base metal processing operations often treat process tailings and acid mine drainage using a high density sludge (HDS) water treatment process. Lime is used in this process, which reacts with existing sulfates to form gypsum. When a recycle stream is incorporated in the process, gypsum levels in recirculating water may build up and cause high levels of gypsum supersaturation. Precipitation of gypsum from the supersaturated process water causes many problems. It is speculated that gypsum may precipitate on sulfide minerals and silica gangues in the flotation circuit, resulting in decreased selectivity and recovery. An understanding of the determinants and nature of precipitation may provide solutions to mitigate the formation of precipitates and improve flotation performance. This study showed that both sphalerite and silica exhibited gypsum- or calcium carbonate-like behavior in the respective supersaturated solutions, indicative of a coating of calcium species on the mineral particle surfaces. The addition of copper sulfate and/or potassium xanthate had little effect on the precipitation of gypsum or calcium carbonate on the mineral particles. Sodium carbonate is encouraging as a method to minimize calcium species interactions on sphalerite/silica surfaces.

Jan 1, 2006

By C. Stamberg, W. McGuire, R. C. Carlson, L. W. Vollmer

"The selection of materials and pre-cautionary measures for handling natural gas and condensate containing aqueous hydrogen sulphide are presented. Based on the results of a pilot production test and laboratory studies, together with several years . of operating experience, it was found that the behaviour of materials in sour gas environments can be predicted sufficiently accurately for engineering purposes.The selection of proper materials is essential for preventing sulphide-stress cracking. Where high strength materials are not required, low car-bon steel is used. Components requiring high tensile strength and hardness characteristics should be made from K-monel or properly heat-treated carbon-manganese-molybden-um and AISI 4140 steels. Welded connections are a potential source of sulphide-stress cracking. Consequently high quality welding and strict inspection are suggested as the most economical precautionary measures available.A maintenance program based,. where possible, on visual inspection of equipment and/or test spools located at strategic points should be used to follow weight loss and putting corrosion in sour gas environments. If severe weight loss or pitting corrosion is encountered, inhibitors have been found to be an effective deter-rent."

Jan 1, 1960

By Yves Prévost, Guy St-Amant, Guillaume Dion

In 2010, the foreseen increase of copper grade in feed concentrate at the Horne Smelter was a significant challenge to maintain a steady copper flow throughout the process. The Horne Smelter process includes a Noranda Reactor, a Noranda Converter, pyro refining vessels and anode furnaces. Of the many challenges involved, improving the single casting wheel performance was one of the key topics. Its reliability had to be improved to meet the new production objectives, as anode copper production was to increase from 170 000 to 225 000 tonnes/year. A multidisciplinary team was dedicated to improve the casting wheel availability. The improvement project allowed pinpointing failure modes and reviewing operational and maintenance practices. The common understanding developed by the team allowed improving small components with a high gain-to-effort ratio. The project allowed reaching operational targets without any significant investment. INTRODUCTION In operation since 1927, the Horne Smelter, located in Rouyn-Noranda, in Quebec, has undergone several technological changes since its original construction. Built to smelt the Horne mine concentrates, the smelter also accepted some local custom feeds from the first years of operation. When the Horne mines stopped production in 1976, the plant became a 100% custom smelter. With the development of the Noranda Reactor (1973) and Noranda Converter (1997), the Horne smelter increased its productivity and improved its environmental performance. Continuous improvement of the Horne process allowed maintaining a high level of flexibility in the operation of the smelter, while improving its overall capacity.

Jan 1, 2019

By X. T. Feng, Y. H. Hatzor, Y. Tal, G. Yagoda-Biran

"When studying jointed rock mass deformation around underground openings it is of great importance to model correctly the excavation sequence during the numerical simulation. This is because for effective arching mechanism to develop in the roof minute block displacements must take place and some of the available discontinuities shear strength must be mobilized. If from the beginning of the simulation the underground opening already exists in the numerical model, block displacements into the excavation space will initiate and develop from time zero, before the initial stresses in the model have attained their actual initial level in the field. These initial block displacements are therefore artificial and exist only in the numerical model, not in the physical reality, and may lead to erroneous assessment of the stability of the designed structure, typically on the conservative side. We have introduced sequence excavation capabilities both in the numerical manifold (NMM) and the discontinuous deformation analysis (DDA) methods and show here the advantages of this modification using three different case studies, each illuminating a different aspect of this enhancement.We begin with the 25 meter deep 2000 year old underground Zedekiah limestone quarry below the old city of Jerusalem, Israel, which is still standing today unsupported with a free span of 40 m. We show that when the opening exists from the beginning of the numerical simulation the required friction angle for roof stability is 25 degrees, whereas when the opening is removed after all stresses and displacements in the model have been stabilized the required friction angle for stability is only 15 degrees.We then model the excavation sequence of a tunnel model representing a 2500 meter deep research tunnel in the Jinping hydroelectric project, China, in order to determine the in situ stress field at this depth by a grid search inversion of displacement data obtained using the sliding micrometer technology in the course of tunnel excavation. Thus we are able to constrain the in situ stress field at these depths where standard in situ stress measurement procedures are extremely difficult to execute properly.Finally, we use sequence excavation modeling capability to find the total height of the expected loosening zone around tunnels excavated through columnar jointed basalts which pose a great engineering challenge because of the characteristic dense network of slender prismatic blocks that transect the opening at a steep inclination. We use MPBX data obtained during excavation of a deep tunnel through such a rock mass to validate our numerical results and show that application of standard empirical guidelines for dimensioning rock bolt reinforcement in such rock masses may in fact result in very un-conservative design because existing empirical approaches typically ignore the anisotropic nature of the structure of such rock masses which, as we show, plays a very significant role in determination of the extent, shape, and geometry of the loosening zone around the opening."

Jan 1, 2015

By A. Roy, T. LeBel, P. Coursol, P. Lind

At the early stage of a mining project, small amounts of concentrates are available for testwork. For gold concentrate or ores containing significant arsenic levels, batch bench scale roasting is often unreliable, leading to highly variable gold recoveries to be used in the project’s financial justifications. With an appropriate bench scale unit using continuous feeding and residence time control for solid and gas phases, reliable numbers can be obtained at small scale with only a few hundred grams per test condition. This paper describes the development of a pilot fluid bed roasting unit by Kingston Process Metallurgy Inc. (KPM) to perform representative trials on gold concentrates containing arsenopyrite, arsenian pyrite and carbonaceous components. Calcines produced under different conditions were characterised by chemical analysis and electron microprobe; the calcine microstructure obtained is described. The most important parameter affecting gold recovery is oxygen content in the roasting atmosphere, with the lowest controlled oxygen level giving the highest gold recoveries. Higher local temperatures in the bed may cause the formation of molten glassy phases which can also reduce the gold recoveries significantly. The impact of roasting conditions in the two inch fluid bed is compared with commercial results obtained in full scale operation.

Jan 1, 2014

By D G. Boxall

As an alternative to heavy water cooling, reactors cooled by organic liquids are being actively developed in Canada under the sponsorship of Atomic Energy of Canada Limited. One of the areas in which development has been required is that of core materials. The factors affecting the selection of fuel canning and coolant tube materials are discussed. It is shown that S.A.P. is a potentially attractive material for these applications. The fabrication of fuel sheathing is discussed. Difficulties met due to large inclusions and blistering due to high hydrogen contents have been overcome by magnetic separation and vacuum sintering of the powders. High-quality tubes can now be produced by extrusion to finished size. A study has been made of the mechanical properties of fuel-sheathing tubes and bar stock. The stress rupture properties of the tubes subjected to uniaxial and biaxial stress have been determined. The biaxial stress tests were performed by internal pressurization. For times in excess of about 200 hours, the curve of stress against time to rupture is extremely flat. The secondary creep rates of

Jan 1, 1965

By D. E. Keeley

Introduction Gunite is a mixture of sand and cement applied to any surface by being shot by compressed air through a nozzle, where it is wetted just before leaving the orifice. The mixture is transported through a hose from a machine called a 'cement-gun'(l). Guniting of rock surfaces has been standard practice at the Mcintyre Porcupine Mines, Limited, for several years. Where used on walls and backs of cross-cuts; shaft stations, and other rock openings, as an air seal, gunite has eliminated the necessity of constant scaling to keep rock from falling from these places, and, under worse conditions, it has been used in place of timber supports. This has been of definite help in reducing costs, promoting safety, and minimizing fire hazards. During the past year guniting has been quite extensively used here in the rock head-works of the new internal shaft, No. 12, sunk from the 3,875-foot level. Gunite is at present being applied to the stations of that shaft well below a mile from the surface. This paper describes the method of guniting as carried out at the McIntyre, and illustrates how, by the adoption of this process, mining problems connected with scaling and loose ground have been completely solved. It is hoped that the information presented may stimulate discussion and assist in the use of gunite in this and other mines. The guniting method of applying cement was first developed by Carl E. Akeley (2), Curator of the Field Museum, Chicago, in 1907, and was exhibited in New York at the Cement Show in 1910. The museum was located in one of the old World's Fair buildings, built of roughcast and in bad repair. Mr. Akeley, who was a man of inventive nature, set about devising means of applying cement to repair the walls. The cement-gun was the result. Mr. Akeley was a taxidermist of note, a sculptor, and also the inventor of the Akeley camera. In his work, he was in the habit of using fast setting materials to build up foundations for statues, etc.

Jan 1, 1934

By D. T. White

Pressure acid leaching of nickel laterite ores typically involves the production of an intermediate product that is releached and refined to pure nickel and cobalt products. BHP Billiton is developing the Ravensthorpe Nickel Project to produce up to 50,000 t/y of nickel via a mixed hydroxide intermediate, which will be refined at its Queensland Nickel (QNI) Yabulu Refinery near Townsville, Queensland. The hydroxide precipitation flowsheet has been adapted to process high magnesium ores through an atmospheric leach stage, eliminate iron(III) as jarosite and oxidise iron(II) during neutralisation. The neutralisation conditions are controlled to precipitate aluminium, chromium and silicon, and to ensure good solid-liquid separation. Soluble impurities such as magnesium are purged with the tailings stream and will be managed over the long term by crystallisation in evaporation ponds.

Jan 1, 2006

By A Falter

Gyroscopic surveying instruments, which apply the physical law of a gyroscope, are being used for deter-mining the azimuth of lines with a high degree of ac-curacy. In the past ten years, gyro-theodolites have been introduced widely for underground orientation in the mining industry of Russia, Germany and South Africa. Gyroscorpic methods eliminate awkward procedures of conventional shaft plumbing, and provide more safety, excellent control and the highest precision at any point under-ground without interference with hoisting operations. The advantages of gyroscopic orientation in geodetic surveys become obvious in primary and secondary triangulation, in the determination of co-ordinates of single triangulation points, using the method of trigonometric re-section and intersection, and when traversing over long distances or in areas with obstructed view. Other fields of application are found in geophysical surveys and in the orientation of technical objects; e.g. radar stations, relay stations and ballistic missiles.

Jan 1, 1964

By J. B. Gilliatt

The discovery of ore at Wabana was quickly followed by the mining of the ore beds where they outcropped in the land areas. The third phase, as at present carried out, consists of extensive submarine operations, which were commenced in 1908, by driving a pair of slopes out under Conception bay, opening. the mine for a distance of a mile and a half from the shore. Two other slopes, now driven just beyond the shore line, are being sunk to the submarine territory where, it is generally recognized, huge reserves of ore lie under the bay. The process of erosion of the land, the solution and re-disposition of its iron-bearing minerals in thick beds of ore have been considered elsewhere, but these bear small relation to the physical forces which have acted upon the ore-beds since the deposition of the strata. These physical changes are made manifest by jointing and cleavage and faulting. The discussion of these, the relation they bear to each other, and to the folding of the strata, is the purpose of this article. For the benefit of those who may not be familiar with the formation in which the ore occurs, I include a general summary of the geology of Be!! island and its environs; also a description of conditions that prevailed during the period of deposition, so that the reader may appreciate some of the later changes that took place during or subsequent to its emergence from the sea, and the folding or tilting of the strata to the position it now occupies.

Jan 1, 1924

By H. Kalsi

"IntroductionRoyal Oak Mines Inc. is currently operating the Parnour No.1 mine located 10.5 miles east of Tinunins, adjacent to Highway No. 101. The operation produces gold ore at a rate of 3300 tpd. A variety of mining methods including bulk open stopes with ITH drilling, narrow vein panel, longhole and open pits contribute to produce 1.2 rnillion ore tons annually. The milling process requires water at an average rate of 1 rnillion gallons per day (700 U.S. gpm). The Pamour No.1 mine has historically had two major problems with regard to water control. The flfSt is the underground pumping system's inability to handle excess inflows of water generated from spring thaws. When the thaw takes place over a short period of time, large inflows of water are created which quickly migrate underground and sometimes result in the loss of the lower loading pocket. During the spring runoff the pumps at Parnour No.1 work continuously for 24 hours at a rate of 1200 U.S. gpm. The system was further taxed in 1991 when the Hoyle mine was connected to the Parnour No. 1 mine and whatever excess capacity the pumping system had for the spring runoff was taken up handling the inflow of mine water generated by the Hoyle.The second problem facing the mine was the lack of water for the mill during the severe cold winter months and dry summer months. At those periods inflows of water into the mine decline and the underground water normally pumped to the mill is severely decreased. In times of dry spells mill personnel increase the water diversion from the Three Nations Lake in order to meet water demands and maintain tonnage throughout. In essence, the mine was going through an annual ""feast or famine"" situation and a solution was needed.A number of options were considered but were narrowed down to the two most practical. The first was to modify the existing pumping system and increase its capacity in order to handle the excessive runoff during spring thaw. This involved a heavy capital expenditure and would have caused additional operating costs (i.e. increased hydro). The option chosen by the management was to divert the spring runoff into an unused section of the mine called The West End. A bulkhead placed at the 2400 level would provide an ultimate underground water storage potential of 150 million gallons. This would also cut down the load on the existing pumping system, save electric consumption in pumping and provide water storage which could be used for milling during the two dry spells. Pumping stored water from the mine could be scheduled for off peak hours to take advantage of lower power rates. To meet these objectives an underground bulkhead capable of withstanding high water pressure up to 2000 ft head (866 psi) was constructed in the spring of 1992. The bulkhead site was at the 2400 level at the Pamour No.1 mine. A major consideration was the requirement to construct a safe bulkhead and to minimize water leakage from the bulkhead.Figure 1 shows the bulkhead location."

Jan 1, 1994

By Terry Aben

Outline ?Review of standards that can be used to identify current coating conditions and optimal points to perform coating maintenance. ?Identify how standards can be used to extrapolate the future condition of coatings to achieve predictive maintenance planning. ?Demonstrate how the above can be combined with project estimating to generate a data driven, quantitative, predictive, risk-based asset integrity maintenance program for Protective Coatings. The Value of Asset Integrity Programs ?Maximize the benefit produced from the investment in maintenance spending. ?Get the best bang for your buck! ?Don?t perform maintenance work before it is necessary ?Money is invested early with no increase in the service life extension. ?Don?t delay until it is too late. ?Planned Maintenance is far less costly than Reactive Maintenance. ?Identify the Optimal Point for Maintenance.

Nov 1, 2011

By J. Spross

"The Key Lake mill has operated since the fall of 1983. The ore from both Key Lake open pits will be depleted by 1997. It is planned to use this mill, located about 60 km southwest of McArthur, to process the McArthur River ore.While the geological data collected so far on the McArthur deposit are encouraging, more information of the deposit is needed before any detailed mine planning can begin.The surface drilling program identified the orebody and provided information on the geomechanical and hydrological properties of the overlying sandstone. It was proposed to conduct an underground exploration program to further delineate the orebody. This was air proved following a public hearing and review process. This program involves the sinking of a 630 metre deep shaft and the driving of one or two drifts along a portion of the orebody. From these drifts, exploration drilling every 10 m to 15 m through the orebody will provide the information required for the preparation of a feasibility study and an Environmental Impact Statement (EIS)."

Jan 1, 1994

By M. Honarmand, Z. Moezifar, H. Ranjbar

Abstract - The Sar Cheshmeh area covers an area of 640 km2, and is located in the southern part of the Iranian Volcanic-Sedimentary Belt. ETM+ images have been used for alteration mapping. The Crosta method was found useful for enhancing exposed areas containing hydroxyl and iron oxide minerals. However, field checking has shown that this method is not able to identify all the known areas of hydrothermal alteration. Many of these altered areas are also not clearly resolved in the geophysical data. In order to improve resolution of such areas, integration of remote sensing and geophysical data may be helpful. The Darrehzar Cu deposit was chosen as a control area. The data have been divided into two sets: explanatory and target variables. The explanatory data are Landsat hydroxyl and iron oxide images and airborne geophysical data (K, U, and Th total counts, and total magnetics). The target variables are rock geochemistry and ground geophysics. Data analysis and integration of geophysical and remote sensing data were performed using directed principal components. This technique is found to be useful for the delineation of hydrothermally altered areas with more confidence.

Jan 1, 2002

By H. Rafiei Renani, C. D. Martin

"The Cohesion Weakening Friction Strengthening (CWFS) is adopted in numerical analysis to capture the observed progressive failure of hard rock pillars. As a case study, pillars at the Elliot Lake mines with width to height ratios of 0.5 to 3 were analyzed in FLAC3D. Pillars with width to height ratios of 0.5 and 1 show a very similar strain softening behavior while with width to height ratios of 2 and especially 3 indicated prolonged strain hardening. The CWFS model successfully captured the mechanism of progressive failure observed in hard rock pillars including initiation of spalling at the corners, progress of spalling towards the centre and formation of hour-glass shaped pillar, and eventually shearing through the width of pillar. Both the CWFS model and site specific empirical formula successfully separated the stable and failed cases in the Elliot Lake mines. While both models are in reasonable agreement for width to height ratios of less than 2, the empirical formula gives increasingly lower strength values for wider pillars which may result in excessively conservative and uneconomical design.INTRODUCTIONPillars are the portion of in situ rock left between the adjacent openings to maintain the stability of excavations. Conditions of equilibrium require that the loads previously carried by the excavated rocks be transferred to the pillars resulting in elevated stresses within the pillar. Hence, prediction of the behavior of pillars under these loads is important for underground design. Determination of the strength of pillars is a classic subject in underground mining. In conventional mining methods such as room and pillar operations, economic incentives point towards higher excavation ratios i.e., leaving smaller pillars between the mined excavations, while safety and stability requirements favor wider stronger pillars. In some mining methods such as caving operations, the problem is even more challenging. On one hand, the whole operation is directly dependent on the proper continuous flow of caved ore between the drawpoints which requires optimizing the spacing between drawpoints and thereby often leaving narrower pillars. On the other hand, the pillars should be wide enough to ensure the safety of mining operation. Both the blockage of drawpoints as a result of wide pillars and uncontrolled failure of narrow pillars can jeopardize the investments and mining operation.Therefore, design of pillar poses a somewhat unique challenge to rock engineers where simple conservative approaches frequently used in other design methods are no longer acceptable. The behavior of pillar under elevated loads should be predicted accurately."

Jan 1, 2015

By H. G. Wang

The production process of a coal mine can often be interrupted by all kinds of events scheduled or unscheduled and thus often needs gas drainage for a temporary or long-term sealed area. Gas drainage has a relatively high risk, therefore attention must be paid to its design to keep the process safe. Based on the conservation laws of mass and constituents, and under the conditions of the allowable gas concentration limit in the return air route, the relationship between gas concentration and gas drainage flow rate as a function of time during the drainage process is discussed in detail to build a mathematical model of gas drainage from a sealed area. With respect to the gas drainage process, two different conditions need to be considered: one with a methane free fresh air supply, the other with a low gas concentration. This paper presents the derived mathematical models for these situations and then shows that they can be incorporated into one model with some modification. This combined model can be employed to determine the optimum gas drainage flow rate with the shortest drainage time. The application is coded using the C# programming language within the .NET framework. Finally, the application program developed by the author is used to validate the mathematical model through an example of gas drainage with varying rate.

Aug 1, 2013

By P. H. Rodriguez

The aquatic hazard classification system of the OECD and EU requires that sparingly soluble metal substances (SSMS) be tested using the OECD Dissolution/Transformation protocol in order to quantify the release of the ecotoxicological relevant species (dissolved ions). The SSMS category contains massive forms of metals, which due to their low solubility and slow transformation characteristics are a special case. The main factors that produce the release of metal into solution are exposed surface loading, pH, and stirring rate. The classification system at present prefers the use of mass loading as opposed to surface loading, in which case the amount of metal released will primarily be a function of the pH, and mass loading. Within the framework of the European Copper Voluntary Risk Assessment, coordinated by the European Copper Institute, we have proposed and developed a methodological procedure in which we demonstrate that surface area is an intrinsic property of a SSMS and we link the exposed surface loading to the toxicity reference value in order to obtain an aquatic hazard classification for massive metals. As example, the aquatic hazard classification for copper massive will be discussed. This approach is recommended for metal massives and metal powders.

Jan 1, 2007

By K. Adham, T. Buchholz

"Significant capacity increases to meet new production demands can often be fulfilled through debottlenecking of an existing production facility, rather than the more expensive option of building new plants and facing new environmental and infrastructure challenges. To achieve that goal, it is important to model and calculate the existing ultimate capacity of each processing plant area, and that of each key equipment sector within the plant areas. This paper describes a methodology of how process modeling tools can be used to simulate the processing steps, how to estimate their existing and ultimate capacities, and how to determine the sweet-spots (minimum cost points) for a plant expansion – leading to a road map of the subsequent debottlenecking project implementation.The debottlenecking technique is presented through a generic work-flow narrative which can be applied to different mineral processing studies, starting with establishment of heat-and-mass balances, drawing a bottleneck diagram, brainstorming capacity increase options, and preparing a cost-capacity curve. Hatch has successfully applied this technique to a number of plant capacity studies, with great benefits to our industrial clients.INTRODUCTIONWith the softening of the metals and minerals prices, and the escalated costs of building new processing plants, it is now economically more viable to improve and debottleneck the existing facilities, rather than build new ones. However, spending new money on old plants requires careful considerations, in order to identify the most economically advantageous incremental steps of improvement and the best potential returns on investment. Process modeling, hand in hand with plant measurements, can identify the best scenarios to balance the three aspects of plant capacity (nameplate, utilization and yield), both at the global and the individual system and subsystem levels."

Jan 1, 2016