Search Documents

An Atomic Force Microscope (AFM) was used to measure the surface forces between glass sphere and silica plate in CnTAC1 (n=12, 14, 16, 18) solutions. The results showed the presence of long-range attractive forces that can be fitted to single exponential functions. With a given surfactant, the attractive force increased with increasing concentration, and reached a maximum at the point of charge neutralization (p.c.n.). The decrease in the attractive force above the p.c.n. is probably due to the inverse orientation of the surfactant molecules. A plot of the log (p.c.n.) vs. the number of carbons in the hydrocarbon chains of the Cn TACI homologues showed a linear relationship with a slope of -0.37, indicating that the surfactant adsorption entails a decrease in free energy by -0.85 kT per mole of CH2 (or CH3) group. These results suggest that the adsorption of long-chain surfactants is controlled by hydrocarbon chain association during the process of forming surface hemi-micelles (or domains). Possible origins of the long-range attractions are discussed on the basis of the results presented in this communication.

Jan 1, 2006

By Hajime Miki, Gde Pandhe Wisnu Suyantara, Ahmed Mohamed Elmahdy, Hidekazu Matsuoka, Kyushu University, Tsuyoshi Hirajima

"Selective flotation of chalcopyrite and molybdenite was studied using various surface treatment methods such as electrolysis, ozone treatment, and plasma. Oxidation via electrolysis method indicated that only chalcopyrite surface is affected by electrolysis due to conductivity difference with molybdenite. Oxidation treatments and XPS analyses indicated that chalcopyrite became hydrophilic due to deposition of oxidized iron on its surface. Various oxidizing methods also showed that chalcopyrite was selectively oxidized and this can apply selective flotation of chalcopyrite and molybdenite. The possible mechanisms are proposed in this work based on surface analyses and thermodynamic calculations.INTRODUCTIONCopper sulphide minerals often associate molybdenite (MoS2) which is one of the most important by-products (Wills, 2006). It is important to recover molybdenite perfectly not only since molybdenite is valuable mineral, but also contamination of molybdenite into copper concentrate or contamination of copper mineral into molybdenite concentrate indicates penalty for both concentrate values (Wills, 2006). Conventional separation of copper sulphide and molybdenite has been achieved with sulphide bulk flotation followed by selective molybdenite flotation with NaHS addition since NaHS works as a depressant for copper sulphide. However, this current process shows imperfect molybdenite recovery and depressant such as NaHS needs to be used under specific flotation plant since it might be environmental contaminant. Hirajima et al., (2014) have been studied selective flotation of molybdenite and chalcopyrite (CuFeS2), which is the most important copper mineral, with plasma pre-treatment. They reported that plasma pre-treatment process followed by washing treatment can improve molybdenite floatability and depress chalcopyrite. This result is attributed to surface oxidation and selective conversion of chalcopyrite and molybdenite wettability. It may be hypothesized that another surface oxidation methods could give a similar result as plasma treatment process. To test this hypothesis, in this study, as comprehensive study of oxidation effect, various oxidation methods such as electrolysis, ozone, and plasma were investigated. Electrochemical measurements, thermodynamic calculations to predict the chemical reactions happened during the process, various surface analyses, and flotation experiments were carried out."

Jan 1, 2016

Agenda ?Trends in Wireless Technology ?Success and Opportunities ?Improving plants efficiency ?Improving plants reliability ?Improving plants safety and security ?Wireless Ecosystem ?Lessons Learnt / Recommendations Why Wireless? ?Lower cost (no wiring cost) ?Flexibility (no wire) ?Standards-compliant wireless devices major factor enabling growth:?Standard WLAN (IEEE 802.11)?Wireless field I/Os (IEEE 802.11, ISA100.11 and WirelessHART) ??Wireless adoption will become a milestone that will rival the introduction of Fieldbus and the distributed control system (DCS) in its importance.? ARC Advisory Group

May 1, 2009

By I. A. Cameron

In 1979, John Peacey and William (Bill) Davenport published The Iron Blast Furnace Theory and Practice billed as "An up to date and comprehensive treatment of blast furnaces from fundamental principles to modern operations" (back cover). As a 1979 graduate of McGill University’s Metallurgical Engineering program, I belonged to the last "beta" student group which completed the prescribed blast furnace course work before The Iron Blast Furnace Theory and Practice was published. As my career developed, I become an international blast furnace consultant and have worked with blast furnace operators and raw material suppliers on 5 continents. The blast furnace is the dominate iron making process responsible for 70% of global steel production. Blast furnace engineers have implemented many improvements by manipulating the blast furnace process metallurgy using the principles presented by Peacey and Davenport to reduce coke consumption and increase oxygen usage and blast furnace productivity. This paper briefly summarizes some key principles presented by Peacey and Davenport (1979), describes process improvements made by blast furnace operators over the 35 years since The Iron Blast Furnace Theory and Practice was published and outlines important future developments in blast furnace technology.

Jan 1, 2014

By A. D. Misener

Introduction Temperature gradients have been determined for numerous locations in the Canadian Shield in connection with mining operations (1, 2, 12, 13, 14, 15). As part of a programme of geophysical studies of this region, some of these gradients were re-determined by the writer at locations where other thermal properties, specific heat, thermal conductivity, radioactivity, etc., were also to be measured. The ultimate object was to determine the heat flow to the surface at these locations. It was felt that the practice of determining heat flow from the temperatures and conductivities obtained in a single vertical bore hole (3, 4, 5, 6, 7, 8, 9) might give results which were appreciably divergent from the average for a considerable area. Particularly, it was thought that temperature gradients, whether obtained in a single vertical hole or from a number of random locations at various depths in a mine, might be subject to local variations and anomalies serious enough to render unsure any discussions based on them. The procedure followed in this investigation was to select a location where mine workings extended to considerable depth over a reasonably wide area. At selected depths below surface, horizontal drill holes extending into regions of undisturbed rock were located and resistance thermometers were inserted into these holes far enough to record the true rock temperature. An attempt was made to obtain a sufficient number of readings at or near any one level to give a representative coverage of the area selected. This ideal could not always be attained, but the large number of readings obtained for each are a does give a reasonably representative picture of the temperature conditions. These readings required much rime and movement of men and equipment underground . They could not have been obtained without the wholehearted co-operation of the management and considerable assistance from the personnel of the mines concerned.

Jan 1, 1949

By J. C. Farge, G. G. Jacox

"The effect of composition and process variables on the properties of Marmet and modified Ni-Hard slugs will be discussed. The effect of shape on the over-all performance of grinding media and its relationship to the end product has been investigated and these results will be reviewed. The cost effectiveness of slugs versus balls has been well documented under various operating conditions and this will be presented in detail. IntroductionThe selection of grinding media is based on the cost-to-wear ratio combined with the consideration that it must stand repeated impacts without breaking. The specific consumption of grinding balls and slugs depend s primarily on their microstructure, which, in turn, is controlled by chemical composition and by the processing condition s to which they are subjected during manufacture.The first part of the paper deals with the optimization of alloy content to produce cast iron slugs with microstructures consisting essentially of marten site and carbide and with hardnesses of 650 B.H.N. and higher. The second part deals with the use of cast iron slugs to replace forged steel balls in milling operations. Tests indicate that the shape of the media has little if any effect on results and that the hardness and microstructure of grinding media will determine its relative performance. Where price is equal under similar milling conditions, the cost effectiveness of cast iron slugs is superior to that of forged steel balls.In order to understand the role of alloying elements in cast irons, it is judicious to consider the microstructural changes which occur during solidification and subsequent cooling, particularly from above the eutectoid temperature. Solidification starts with the formation and growth of dendrites of austenite. As temperature decreases, an eutectic nucleates and grows between the primary austenite dendrites. Immediately after solidification, the structure consists of proeutectic austenite and of the eutectic of primary carbides and austenite. On cooling to room temperature, austenite can be retained or transformed to pearlite, bainite, martensite or mixtures thereof. It is necessary to prevent decomposition of austenite into pearlite by adjusting the alloy content. For best abrasion resistance, the microstructure at room temperature should consist essentially of martensite and carbide. These types of irons are known as ""martensitic irons "". Depending on the carbon content of the austenite and cooling rate, "" as-cast"" martensitic irons will contain different proportions of martensite and retained austenite. The more carbon in solution in the austenite, the lower is the temperature at which the martensitic transfoemation takes place. By the time room temperature is reached ., the transformation is seldom complete, and the end product is generally a mixture of martensite and retained austenite."

Jan 1, 1980

By M. A. Sobhi, L. Li

With the continuous reduction of mineral resources at shallow depth, more and more mines have to go deeper beneath the earth's surface to reach the ore zones. This increase in mine depth leads to a natural stress increase, which also raises the stresses around mine openings. This may result in ground instability, including the risk of rock bursts or exceedingly large opening closure. Stope backfilling is a well known solution to improve the ground stability condition. It also has the advantage of reducing the mining wastes disposed on surface, thus helping to reduce the environment impact from the industry. However, most available solutions for backfill design were developed for an isolated stope without taking into account the influence of mine depth, except for a few numerical analyses performed recently by Falaknaz and coworkers for the case of multiple backfilled stopes laying in the same level. In this paper, a numerical study is carried out to evaluate the stresses in backfilled stopes overlying a sill mat. The mine depth and the excavation of the underlying stope below the sill mat are both taken into consideration. Compared to the case of a single isolated backfilled stope, the obtained numerical results show that the stress magnitudes in the overlying backfill are considerably increased due to the excavation of the underlying stope. In general, the stresses increase with mine depth and backfill stiffness, but decrease with an increase in the surrounding rock mass stiffness. These results indicate that the barricade and sill mat backfill design should take into account the excavation of the underlying stope and the mine depth.

Jan 1, 2015

"9.1. IntroductionThe application of the electron microprobe for in-situ analysis of platinum-group minerals (PGM), first reported by Borovskii et at. (1959) and Genkin (1959), has resulted in a large and growing number of analyses of unidentified PGM. Figure 9.1 charts the increase in the number of reported unnamed PGM from 3 in 1959 to a total of 140 by 1979. All these minerals, with the exception of UN1968-5 and UN1976-1, were analyzed with the electron microprobe.There has been no recognised or consistent manner for reporting these unidentified PGM. The term ""unnamed"" has been used for PGM that are considered to be new species without a name as well as for PGM which have not been exhaustively compared to named and unnamed PGM in order to determine whether they are unique. Many of the so-called unnamed PGM are only unnamed because of poor microprobe analyses or because larger than usual elemental substitutions (e.g. Bi for As) made it difficult to calculate the true stoichiometry. Some of these unnamed minerals have been unnecessarily reported with non-stoichiometric formulae, as discussed by Cabri (1980). Better analytical data should reduce the number of such proposals.Another unfortunate practice, possibly used to by-pass the scrutiny of the Commission for New Minerals and Mineral Names, I.M.A., is to report a ""new"" mineral by referring to it by a name made up of its constituent elements. This has been deplored on a number of occasions (cf. discussion in Fleischer et at., 1976, p. 179), but some journals continue to publish such material. The Commission on New Minerals and Mineral Names has not recognised such ""names"" and these PGM are therefore included in this chapter with other unnamed minerals.A further example of inconsistency in reporting unnamed minerals is the report of a specific ideal stoichiometry with no further details (not even an analysis!); sometimes with a note that this will be reported in greater detail in due course. I have also been guilty of similar optimistic statements and, unfortunately, it is not always possible to follow through. Some authors give data on unnamed minerals in such a discrete manner that their reports are sometimes missed in literature searches."

Jan 1, 1979

By Charlie Jefferson

Main Goal: Resource Assessment 1. Incorporate existing data & results, old process. 2. NEW Quantitative Analysis (Chung and Chen) 3. Try mass balance of U and geochemical tracers 4. Use holistic process approach ?with key foci ?Targeted basin / belt assessments ?Is there as much in the Athabascaas they say? ?Athabasca reference for other basins (Thelon, etc) ?Compare sandstone & volcanic with USA, Kazakhstan etc: do their models apply here? ?Which IOCG systems are prospective for uranium? 5.Consider Groundwater, Environment; 6.Communicate

May 1, 2006

By C. Morlot, C. Auvray, E. Fourreau, J. Talandier

"During the excavation of underground galleries in a rock mass, reorganisation of the stress field around the site results in damage to the surrounding material. In the framework of research undertaken at the ANDRA underground laboratory in France, galleries have been excavated in a Callovo-Oxfordian argillite formation. The damage has manifest as a number of fracture systems in the adjacent rock. Observations have shown that fractures generated during excavation and storage exploitation are able to self-seal during re-saturation of the site in the post-closure stage. Although indirect evidence for argillite self-sealing has previously been reported, from experiments performed both in situ and on samples, no direct observations of self-sealing have yet been made.For the present study, we performed a range of self-sealing experiments using a newly-developed triaxial compression cell placed within a nano-CT scanner with a 10 µm resolution. The body of the compression cell is X-ray transparent, allowing sample healing to be monitored directly. The samples contained an artificial fracture that had been generated in the laboratory, into which a fluid was injected. The fractures were orientated either perpendicular or parallel to the plane of anisotropy of the material. Our initial results demonstrate that when fluid is injected perpendicular to the plane of anisotropy, the flow-rate has no apparent influence on the kinetics of fracture closure. Permeability varies significantly, from 2.10-14 to 2.10-18 m2 over 116 hours. Post-test observations of the fracture lips show swelling that appears to be orientated perpendicular to the fracture plane and therefore parallel to the plane of anisotropy. Initial results for an injection parallel to the plane of anisotropy suggest that, in this case, the rate of flow affects the kinetics of fracture closure. For a flow-rate of 0.25 ml/min, closure begins after around one minute. In contrast, for a rate of 0.05 ml/min, it is necessary to wait several minutes before partial sealing of the zone is observed. The reduction in permeability is again significant, from 2.10-15 to 4.10-18 m2 over 96 hours. After completion of the test, swelling was observed in elongated zones that lie parallel to the fracture plane and therefore to the plane of anisotropy."

Jan 1, 2015

By J. L. Blaylock

Normally, the hydraulic system and structures are considered to be unrelated items. In reality, the two cannot be separated because one affects and depends on the other to function properly. This paper explores the potential failure areas of hydraulic cylinders, and suggests possible methods to prevent failures from occurring. The use of high-strength low-alloy steel in frames is reviewed and the benefits discussed. Fabrication techniques and handling of material are noted in the hope that this knowledge will aid in the repair of frames in the field.

Jan 1, 1979

By J. L. Jambor, E. J. Reardon, E. C. Appleyard, J. A. Cherry

Abstract- Since the 1957 initiation of deposition of mill tailings at the Heath Steele mine, New Brunswick, periodic detailed studies of the tailings geochemistry and mineralogy have been con­ ducted, thereby providing a unique opportunity to examine the geochernical evolution of a sulfide- rich mine-tailings impoundment. When deposited, the tailings contained about 85 wt% sulfide minerals, 1 wt% to 3 wt% carbonate minerals, and 12 wt% to 14 wt% aluminosilicate minerals. Mineralogical examination of samples of the tailings from deep in the impoundment indicates that little oxidation occurred prior to tailings deposition. The mill process-water deposited with the tailings was neutral to slightly basic and contained low concentrations of Cu, Pb, Zn and As. Sampling of the tailings five years after deposition indicated that sulfide-oxidation reactions, occurring near the tailings surface, had decreased the tailings-water pH and increased the concentrations of Fe, SOi-, Cu, Zn and Pb (up to 10 000 mg/L, 25 000 mg/L, 2.5 mg/L, 200 mg/L, and 4.5 mg/L, respectively) . In 1975, ten years after decommissioning, the tailings could be divided into three zones: an upper oxidation zone in which sulfide oxidation is actively occurring, a hardpan layer, 15 cm to 20 cm thick, composed of tailings cemented by secondary Fe minerals, and an underlying reduction zone in which the tailings are relatively tinoxidized (Boorman and Watson, 1976). Chemical analyses indicated the presence of low-pH waters containing very high concentrations of SO42- , Fe, and other metals (up to 63 600 mg/L SO42-, 28 600 mg/L Fe, 10 mg/L Pb, 600 mg/L Cu and 4000 mg/L Zn), suggesting that there was a period of intense sulfide oxidation between five and ten years after tailings deposition. More recent sampling, conducted some 20 years after the end of tailings deposition, indicates that relatively little change has occurred in the last ten years, thereby suggesting that the hardpan layer has provided an impediment to the downward movement of dissolved constituents . Analyses of the tailings solids show increased accumulations of many metals at or near the depth of the hardpan layer. Evaluations of the long-term evolution of the tailings can be enhanced by comparison of descriptions of the tailings with descriptions of the gossan that overlay the massive­ sulfide orebody prior to mining. At Heath Steele, this comparison suggests that many of the mechanisms controlling the distribution of metals in the tailings will probably persist over geologic time.

Jan 1, 1992

By Gordon E. Agar

"The effectiveness of two this compounds for copper sulphide depression in molybdenite flotation has been examined with batch bench scale tests.Both thioglycollate and trithiocarbonate proved to be good depressants producing results similar to those f or cyanide and hydrosulphide. Ferrocyanide was ineffective on the samplematerial tested.The depressing effect of thioglycollate was readily reversed by an addition of xanthate.IntroductionThe separation of molybdenite from copper sulphide minerals has been practised for a long time(1,2). The predominant scheme is to depress the copper sulphides while capitalizing on the ready floatability of molybdenite to effect the separation. There are many recipes for depressing the copper minerals(3), among them the addition of sodium cyanide, particularly if the copper is present primarily as chalcopyrite; some form of sulphide whether as sodium sulphide, sodium hydrosulphide or phosphorous pentasulphide when there is a mixture of copper sulphides such as bornite, chalcocite and chalcopyrite; potassium ferro cyanide may be used when chalcocite is the principal copper sulphide; peroxide or hypochlorite; as well as heating in the presence of lime. There are different mechanisms by which these reagent s depress the copper sulphides. Sodium cyanide and the sulphide-producing compounds apparently reduce the potential of the copper sulphides to the point where they ar e rendered unfloatable by xanthates . Another study(4) showed that after cyanide addition, chalcopyrite was rendered un floatabl e until the REDOX potential (measured with a gold electrode with a saturated calomel reference) had become more positive than -250 mY. If the chalcopyrite pulp was conditioned after the cyanide addition the REDOX potential increased slowly, whereas if air was introduced during the conditioning the potential r ose much more rapidly. The difference in time to reach the desired level of - 250 mV was as much as 20 minutes' 25 minutes being required when air was absent but less than 5 minutes when air was admitted . These observation s demonstrate some of the problems encountered when using cyanide to depress sulphides such as chalcopyrite . The system adjusts to counteract the depressing effect of the additive. To overcome this tendency it is necessary to either add an overdose at the beginning or to more or less continuously add the regulating reagent. In this study cyanide solution was added under automatic control to maintain a specified REDOX potential."

Jan 1, 1984

By John A. Herbst, Gerald H. Luttrell, Jaisen N. Kohmuench, Aaron Noble, Michael J. Mankosa

The HydroFloat TM is an innovative fluidized-bed separator that can substantially increase the upper particle size that can be successfully treated by flotation. Recent studies conducted using laboratory, bench-scale and pilot-scale equipment indicate that this technology can be used to float coarse sulfide middlings that cannot be recovered by conventional flotation machines. Recent data collected from pilotscale tests conducted at a base metal concentrator indicate that this technology can float middlings particles as large as 850 microns in diameter containing as little as 1% exposed hydrophobic mineral. As such, the crossover of this technology into the base metals industry has the potential to substantially reduce grinding costs and increase concentrator recovery/capacity through the use of split-feed circuitry. The split-feed concept, which is often used for upgrading industrial minerals, involves segregation of the feed into more than one size class followed by subsequent upgrading using mills/separators/reagents specifically optimized for each size class. In this article, a split-feed circuit is described that utilizes two stages of classifying cyclones in conjunction with the HydroFloat_ separator. The circuit is designed to recover, recycle and regrind coarse middlings containing small amounts of valuable mineral while simultaneously rejecting coarse well-liberated siliceous gangue so that mill throughput can be increased. Simulation data conducted using well-known process models suggest that this approach can increase existing primary mill capacity by up to 25% with only modest investments in new classifying and flotation equipment.

Jan 1, 2016

By Cale J. Dubois

At Cameco Corporations' Cigar Lake Project, large excavations are developed on the 480 Level and 500 Level must remain stable for at least 15 years to host underground processing infrastructure. Following the successful dewatering of the mine in October 2009, subsequent internal rockmechanics investigations augmented by third party technical investigations; determined that to keep the back of the Water Flush Crusher/Run-of-Mine (WFC/ROMs) excavation stable; required a rehabilitation strategy to mitigate deterioration/deformation of the WFC walls and intersection pillars. The mechanism of failure propagating the movement of the excavation walls is understood to be controlled by the presence of a dominant E-W striking and steeply dipping foliation within a relatively weak and mildly altered rockmass sub-parallel in strike with 14 meters high walls and an intersection span approaching 15 meters. The application of open and resourceful communications between site mining engineers, geologists, contract mining staff, construction management experts, corporate mining and civil engineers, and third party technical experts resulted in a multi-faceted short-term ground support strategy consisting of standard bolting and screening, deep-seated modified-strand cable bolts coupled with heavy gauge mesh straps, rockmass reconditioning using low-pressure grout injection, and horizontal cable-lacing for the intersection pillars applied in lifts using a top-down methodology. The intention of the short-term strategy was to stabilize the excavation so that a long-term structural steel support installation - consisting of composite concrete walls, and arch support applied to the side walls and crown of the back - could be constructed safely. This paper summarizes the evolution of the short and long-term ground support strategy and criteria for the WFC/ROMs excavation developed using elements of civil, mining and hydrogeologic design.

Nov 1, 2011

By G. A. Maki, P. J. Fullman, R. G. Roden

"In October 1984, Rocanville Division began using a stacking system to handle potash mill tailings. Previous to this date, mill tailings were slurried to the top of the tailings pile and allowed to debrine while flowing down the pile. With the new stacking system, slurried tailings are fed to mobile stackers. The stackers consist of cyclone packs to debrine the tailings and drag conveyors with screw discharges to deposit the tailings onto the existing pile. This paper deals with the various aspects of the project from conception to its present state.IntroductionPrevious to 1984, when the stacking project was first implemented, potash mill tailings were handled as follows. Mill tailings were first debrined to approximately 65010 solids using a cyclone cluster. The cyclone underflows were then introduced onto a vacuum scroll filter table. Here the tailings were further debrined and discharged into the disposal tank where the tailings were reslurried with reclaim brine and pumped to the tailings disposal site. At the disposal site the slurry was discharged onto the tailings pile and by a natural settling process the tailings were debrined with the brine ultimately collected in the reclaim brine ponds. The shape and profile of the tailings pile was controlled by building salt dykes to control the flow of the discharged tailings slurry. As the tailings pile grew in height, booster pumps were added to the disposal system."

Jan 1, 1990

By Chris V. Sellathamby

Condition-based maintenance is replacing preventive maintenance in many industrial operations as a result of gains in productivity. Preventive maintenance is strictly time-based which means that as long as the prescribed time is sufficiently short, failures are prevented. The trade-offs between shorter cycles and increased downtime is a fine balancing act. Condition-based maintenance is gaining momentum as the more cost-effective and green solution to finding the optimal maintenance cycle and improving overall productivity. In the mining industry, various parameters of heavy equipment are monitored continuously to provide feedback for maintenance events. However, strain, shock, and vibration, key factors which lead to yielding and fatigue of metal parts, are not generally monitored by built-in systems, mainly due to the complexity of sensor installation and computational intensity of data processing. Scanimetrics has developed a stand-alone, add-on wireless system for measuring strain, shock, and vibration in heavy equipment and components, the data from which can be directly used to trigger maintenance events. The present system is being deployed in tar sands mining equipment. The system consists of a portable display and control unit, a software platform consisting of data management, sensor instrumentation and data analysis, and wireless strain sensor units, which can be easily installed on equipment. Data from the sensors can be gathered throughout the mine site, processed instantly, and used to generate condition-based maintenance events, improving overall uptime of the equipment and overall productivity of the mining operation.

Oct 1, 2010

By Matt Manson

Renard?1-10 kimberlite pipes and ?Lynx-Hibou?kimberlite dyke system within ?Foxtrot?property 50/50 JV with SOQUEM, Stornoway operator 2001: Discovery of the Renard kimberlite pipes 2003: Discovery of the Lynx-Hibou kimberlite dykes 2006-2007: Bulk sample program 2008: First 43-101 Resource and Preliminary Assessment 2009/2010: Updated 43-101 Resource

May 1, 2010

By A. Bauer

The correct application of large crater blasts in unfrozen tar sand is an effective means of resisting frost penetration during winter. This results in much higher productivity and considerably less down time with excavators during winter operations. The resulting flatter angle of repose of the highwall has readily been accommodated with slight modification to bucket-wheel excavator operating procedure. Other mining schemes call for large draglines to be located on top of the highwall, which can be as high as J80 feet. The question now arises as to the effect that blasting might have on the stability of such a situation in which the highwall includes potential planes of weakness. This paper applies blast vibration data from large-scale blasting in tar sand to the stability analysis for typical production situations likely to be encountered and indicates safe scaled distances to be employed between dragline and blast.

Jan 1, 1979

By K. Esmaieli

The Synthetic Rock Mass (SRM) approach has the potential to capture the mechanical behavior of large rock samples. In order for the method to be used with confidence it is necessary to gain a good understanding of the factors that influences its analysis. This paper reports on a series of numerical experiments, based on field data from a large underground mine, to investigate the influence of intact rock mass strength of a constructed (SRM). A jointed rock mass defined by three fracture sets was simulated by a Discrete Fracture Network (DFN) model. The generated fracture network was subsequently embedded into six different intact rock samples, simulated by a bonded particle model in PFC3D, generating six SRM samples. Each intact rock sample was 7 m × 7 m × 14 m and assigned different mechanical properties. The first intact rock sample was assigned a uniaxial compressive strength of 205 MPa and an elastic modulus of 104 GPa with the UCS and elastic modulus values of the other samples downgraded by 10% until the weakest sample had a UCS value of 121 MPa and an elastic modulus value of 61 GPa. All SRM samples were loaded under uniaxial compression to obtain the complete stress strain curve. It was observed that the compressive strength of the rock mass samples decreased by 10% following the same trend as the rock material strength. However, the elastic modulus of the rock mass samples decreased non-linearly with reduction of the elastic modulus of the rock material. The Poisson's ratio of rock mass samples does not change with decrease of rock material properties. For the post-peak behaviour the results show that both the brittleness index and the residual strength of rock mass samples decreased as the rock material properties degrades.

Aug 1, 2013