Search Documents

By L. Sun

In this work, strontium doped lanthanum ferrite (LSF) and their composite cathodes were fabricated by screen printing on yttria-stabilized zirconia (YSZ) electrolytes. Their electrochemical properties were evaluated by using electrochemical impedance spectroscopy and steady-state polarization methods. All the cathodes were screened by comparing their total polarization resistances before and after activation processes at different temperatures. The improved LSF composite cathodes were also screen-printed on YSZ/NiO half cells to fabricate solid oxide fuel cells (SOFCs), which have reached the output power densities of 170 mW/cm2 at 650 °C, 230 mW/cm2 at 700 °C, 304 mW/cm2 at 750 °C and 388 mW/cm2 at 800 °C.

Jan 1, 2005

By R. L. Armstrong, C. I. Godwin, V. M. Kruan

"The Scheelite Dome tungsten-bearing skarn property, central Yukon Territory, is in metasediments in contact with a quartz monzonite intrusion. Contact metamorphism to biotite-muscovite- andalusite hornfels and calc-silicate hornfels is superimposed on low-grade regionally metamorphosed rocks represented by quartz-mica pelitic schist and muscovite-biotite pelitic schist.Metasediments are likely Precambrian in age, even though Rb-Sr whole-rock analyses indicate an early Paleozoic age (511±41 Ma); this apparently too young radiometric age is due to partial loss of radiogenic strontium during regional metamorphism. The minimum age of the quartz monzonite intrusion is Cretaceous at 90.4±2.6 Ma (K-Ar on biotite) and its initial 87Sr/86Sr ratio is 0.7121. The high initial ratio of the intrusion is due to the addition of radiogenic strontium from the metasedimentary country rocks and perhaps an underlying older basement.Scheelite-pyrrhotite-chalcopyrite mineralization occurs in diopside-zoisite skarn pods within the calc-silicate hornfels near the quartz monzonite intrusion. The source for lithophile tungsten is probably the same as for the granitic magma, namely Precambrian sialic basement.IntroductionThe Scheelite Dome tungsten skarn property is within the Mc-Questen map-area (NTS: 115P/16),28 km northwest of Mayo, Y.T., at latitude 63°47' north and longitude 136°15' west. The property can be reached by helicopter or by four-wheel- drive vehicle from Mayo.This paper summarizes the geology of the Scheelite Dome property, which has been described in a general way by Little (1959) and Cathro (1969). Geological mapping and sampling were done by the first author (nee Steffler) during June 1979. Field work was supplemented with detailed work at the Department of Geological Sciences of The University of British Columbia during 1979 and 1980 (Steffler, 1980). Whole-rock chemical analyses were done by Cominco Ltd."

Jan 1, 1982

By J. A. Rogers

"The Arthur W. White Mine (formerly Dickenson Mine) is a structurally controlled, hydrothermal gold deposit. A gold producer since 1948, it has, to December 31, 1990, processed 6.9 million (m) tons (T) of ore grading 0.45 ounces per ton gold (oz/T Au). As of December 31, 1991, Proven and Probable Ore Reserves were 3.2 m. T. at 0.32 oz/T Au. The mine is located just east ofPlacer Dome Inc. 's Campbell Mine, within the Cochenour-Gull.rock Lake deformation zone. It is situated on the hanging-wall side of a southeast-plunging anticline in a sequence of metamorphosed Archean volcanic, sedimentary and plutonic rocks of the Red Lake greenstone belt. Ore-bearing structures, found mainly within basaltic rocks, are brittle within greenschist-facies rocks to the northwest, but become more ductile toward the southeast, in amphibolite-facies rocks. Within and proximal to these structures, carbonate and arsenopyrite alteration decreases, whereas biotite, actinolite, pyrite and pyrrh otite all increase to the southeast.Ore and shear structures occur symmetrically about the northwest-trending, steeply southwest-dipping, flattening foliation . The three most common ore trends are on average: (A) northwest trending with a 55 degree to 85 degree dip to the southwest; (B) north-trending with a 40 degree to 50 degree dip to the west; and (C) due east-west-trending with a vertical dip. In general, the dominant direction of economic gold concentrations are explained and thus predicted by considering deformation style (brittle or ductile), rock anisotropies such as bedding and lithological contacts, and direction/magnitude of relative block movement. Direction ""A"" can be found adjacent to both right- and left-handed faults. Direction ""B "" occurs with dominantly right-handed systems and direction ""C"" is found with predominantly left-handed movement. Major faults active prior to, during, and after ore formation can have offsets in the order of 2500 feet. Movements along these faults were transpressive while their conjugate breaks were dilatant, thus creating zones for alteration and ore solution emplacement. A series of faults , each with offsets up to 30 feet were established under lower temperature brittle conditions during late- to post-ore formation. In more complex zones, formed during more ductile deformation, these faults controlled the localized geometry and, thereby, the depletion and enrichment of ore shoots, causing a high nugget effect.Although an important aspect of production planning and monitoring, grade control is also very important within a complex ore zone so that the nuggets are not missed. Detailed observation of structure at the hand-sample scale and detailed mapping at the stope scale give valuable clues to interpreting the structures on a mine-wide scale. Determining the relative movement along fault structures is very important so that using an action-reaction- type logic, potential dilatant areas can be predicted and targeted for development and diamond drilling."

Jan 1, 1992

By A Frydrychewicz, J. Mirza, J. Lipkowski

The objective of this work was to understand the mechanisms of action of additives, such as thiourea, that enhance gold leaching in thiosulfate solution. The leaching reaction and surface passivation were investigated using linear sweep voltammetry. Leaching currents were determined using analysis of current-potential curves and the mixed potential theory. The gold-electrolyte interface was further characterized with surface enhanced Raman spectroscopy. The results show how thiourea prevents formation of oxysulfur compounds, which passivate the gold surface. Other molecules such as 3- m ercaptopropionic acid and L-cysteine were also studied as possible additives to prevent passive layer formation.

Jan 1, 2011

By Jayesh B. Patel, Zhongyun Fan, Hu-Tian Li

"Melt conditioned direct-chill (MC-DC) casting is a novel technology which combines vertical direct-chill (DC) casting with a high shear device directly immersed in the sump for in situ microstructural control. In this paper, the solidification mechanism of DC casting under varying conditions is discussed. The temperature profiles in the sump were measured under the steady state casting conditions by using sacrificing thermocouples. Detailed comparisons of the derived thermal condition are made. The individual role of grain refiner additions, natural thermosolutal convection and forced convection in the sump and the interplay of these factors in determining the solidification structures of DC cast billets are discussed. The MC-DC casting technology can be used to control microstructural constituents and casting defects in DC cast billets/ingots by in situ manipulating of the thermal and fluid flow conditions.INTRODUCTION Direct-chill (DC) casting of aluminium, has been the essential commercial process for producing feedstock suitable for subsequent processing, such as extrusion, rolling or forging. Fine and equiaxed grain structures in the as-cast billets/ingots are required to enable a fine and uniform distribution of second phase particles and microporosity. This leads to higher productivity, more cost-effective homogenisation and more efficient downstream thermomechanical processing. The addition of chemical inoculants has been the standard industrial operation prior to casting for grain refinement of Al alloys. However, it has been established that less than 1% of the grain refiner particles added actually act as heterogeneous nuclei to refine the grain structures, showing a very low grain refining efficiency (Greer, Bunn, Tronche, Evans, & Bristow, 2000). Moreover, the remaining particles from the grain refiner addition in the final casting may cause surface defects during downstream processing. A major issue of the metallurgical quality of large sized ingots/billets is the non-uniformity of microstructures even with chemical grain refiner additions. This is due to the fact that the grain structure formed in the different zones of the billet depends on the local chemical composition and local cooling rate. The local cooling rate can vary from 0.4~1 K/s at the centre of the billet to around 10–20 K/s at its surface zone (Nadella, Eskin, Du, & Katgerman, 2008). The large thermal gradient along radial direction between billet surface and interior of the melt during conventional DC casting induces thermal stress and cold cracking even with grain refiner addition. Therefore the control of casting defects, such as macrosegregation, porosity, cold/hot cracking and distortion of the billets/slabs, etc., is still challenging in industry, causing high scrap rate of DC cast ingots/billets even with grain refiner addition."

Jan 1, 2018

By R. Baker

A novel electrochemical half-cell and corresponding working electrode were designed to evaluate the electro-catalytic activities of catalysts in an environment close to that of an operating proton exchange or polymer electrolyte fuel cell (PEMFC). Cyclic voltammetry (CV) and electrochemical impedance spectroscopy (EIS) techniques were employed using the novel cell to characterize various methanol electro-oxidation parameters that contribute to the overall reaction on a fuel cell anode. The effect of temperature on methanol oxidation kinetics was examined in the potential range of 0.31 to 0.65V (vs. NHE). The data was collected in the temperature range of 20 to 80°C. Based on the experimental analysis and literature data, an equivalent circuit model (ECM) for methanol oxidation was proposed and was used to fit the EIS experimental data. The experimental data and ECM electrochemical data was used to extract electrochemical kinetic parameters for methanol oxidation such as the exchange current density, Tafel slope, and energy of activation for the reaction. Kinetic data, especially at different temperatures, is very limited in the literature.

Jan 1, 2005

By C. V. Sibbald

"This paper provides a description of the Highmont copper-molybdenum concentrator from primary crushing through grinding, flotation, tailings disposal and water reclamation. The unique features of the operation will be emphasized.IntroductionThe Highmont property is located in the southern portion of the Highland Valley adjacent to and east of Lornex and about 4 miles south of Bethlehem Copper. The plantsite is at an elevation of 5100 ft.Highmont acquired the property in 1966 and in 1969 Teck Corporation entered into an exploration agreement which contained the option to finance the property to production . A detailed feasibility study of the project was completed in 1971. A positive production decision was deferred at that time because of the prevailing soft copper market and relatively low molybdenum price. The development of a strong molybdenum market in late 1978 and early 1979 led to a re-examination of project economics, and a decision to proceed to production was made in April 1979.The Highmont ore zones occur adjacent to and on either side of an east-west-trending quartz porphyry dyke. The two major zones , the east and west pits, contain 122 million tons of ore assaying 0.27070 Cu and 0.029% Mo. Chalcopyrite, bornite and molybdenite are the minerals of economic interest. Chalcopyrite is the predominant copper mineral. Mineralization occurs primarily along fractures and is zoned according to fracture density. Some pyrite is present, but for the most part it is outside the ore zone. Surface oxidation is shallow throughout the orebody.Wright Engineers Limited were responsible for the major part of the engineering design. Site construction, which began in the spring of 1979, is under the direction of Commonwealth Construction. The first concentrator line is scheduled for completion late in 1980, the other for early in 1981."

Jan 1, 1981

By T. R. Yu, D. B. Counter

"Kidd Creek Mines primarily employs sublevel blasthole stoping for underground mining operations. During pillar recovery in No.1 Mine and panel mining in No.2 Mine, the free standing fill exposures may reach a height of 100 m or more. Consequently, a competent consolidated rockfill has been required to fill the mined openings.Since 1976, a total of more than fifty stopes and pillars have been filled with over four million tonnes of backfill. Fill exposures, up to heights of 100 m, have stood up well after blasting adjacent to the backfill.The fill material consists of a graded aggregate, Portland cement and ground slag. Sand has been occasionally mixed in the fill material to serve as avoid filler. The aggregate is prepared in a fill crushing plant, transported underground through raises, and hauled to the filling stopes by conveyors in No. 1 Mine and by trucks in No.2 Mine.Two mixing methods are currently in use. No. I Mine utilizes the free fall of gravity; the fill materials are sprayed with cement slurry as the aggregate departs from the conveyor into a mixing culvert. The other is the use of a rotary mixer on a batch basis in No. 2 Mine.This paper describes the fill systems, filling operation s, and the backfill quality control practice, together with various testing results related to improving fill quality as well as reducing fill costs.IntroductionThe Kidd Creek minesite, located 27 km north o f the city centre of Timmins, Ontario, produces 4.5 million tonnes of copper, zinc, lead, and silver ores annually from its No. 1 and No.2 underground mining operations. Both mines employ a sublevel blasthole stoping method."

Jan 1, 1983

By M. P. Filion, K. Ferguson, L. L. Sirois

Acidic drainage is the largest single environmental problem facing the Canadian mining industry today. Technologies to prevent acidic drainage from occurring in wasterock piles and tailings sites, and on the walls of open pits and underground mines, need to be developed and demonstrated. There are two groups in Canada which have accepted this challenge: the national Mine Environment Neutral Drainage (MEND) program and the British Columbia Acid Mine Drainage (BCAMD) Task Force. This paper summarizes the activities of these two organizations.

Jan 1, 1990

By Peter A. Witt

Highland Valley Copper is a conventional truck-shovel mining and flotation concentrator operation located some 75 kilometres southwest of Kamloops, B.C. (Figure 1). The ore is located within a porphyry copper deposit and is mined at a rate of 135,000 metric tonnes per day from two separate open pits. The nearby mill produces concentrates containing 375 million pounds of copper and 5 million pounds of molybdenum metal yearly. In the Valley pit, head grades are roughly 0.40% Cu at a 0.23% Cu equivalent cut-off. The Valley pit strip ratio currently sits at 0.55:1 with waste quantities made up of separate rock and unconsolidated overburden units. From the mill, concentrates are trucked to nearby Ashcroft and then hauled by rail to ocean port facilities in Vancouver. The mine employs 950 persons and is planned to operate until 2009. The operation is a partnership between TeckCominco with a 63.9% interest, BHP Billiton holding 33.6%, and others 2.5%. Management is shared by the two principal owners and directed by a management committee.

May 1, 2003

By J. Peck, M. J. Scobie, M. D. Pollitt

"IntroductionOne aspect of current research in the Canadian Centre for Automation and Robotics in Mining (CCARM) involves the automatic identification of different rock types based on particular drill performance parameter responses. In this paper, the four drill performance parameters of torque, pulldown pressure, rotary speed and penetration rate, were measured from an instrumented rotary blasthole drill during field investigations undertaken at the Fording River Mine, Elkford, British Columbia. The variations in these parameters were subsequently correlated with the corresponding rock types using the results from gamma, neutron and core logs in the same or adjacent boreholes. Work to date has sought to understand the relationships between drilling performance parameter variation and rock properties. Using the results of these studies, the present research is aimed at developing techniques whereby classical statistical pattern recognition methods are applied to drill data to permit the discrimination of different rock units. A monitoring system incorporating such a capability would greatly enhance the quality and amount of geological information on a per borehole basis while drilling. This data in tum could be used economically and directly towards explosive loading, geological exploration and reserve estimation. Background and PhilosophyThis work is an extension of equipment monitoring studies at the Fording River Mine. At this site over a two-year period, 5180 m of data was acquired on an instrumented Bucyrus-Erie 60R drill during routine production blasthole drilling. Throughout these studies, a 311mm diameter S8M Security tungsten-carbide tricone bit was used. The mine, located in southeast British Columbia, is a large-scale, open pit coal operation. The means of excavation revolves around a drill-blast-muck cycle and employs a standard shovel-truck system of transport. Four main rock types are present: sandstone, siltstone, mudstone and coal, with average compressive strengths ranging from 10 MPa to 150MPa respectively (peck 1989). However, based on the field studies, very few differences in terms of strength and compositional properties were seen between the sandstones and siltstones at the site. Therefore, they are referred to as sandstone/siltstone in all further discussions."

Jan 1, 1991

By J. A. Allan

OCCURRENCES of salt in Alberta have been mentioned and described by the writer in 1929 (l) and by Cole in 1930 (2). Brine springs occur at a number of places along the valley of Athabaska river north of latitude 56 degrees, and also on the south margin of Salt prairie, twenty-five miles west of Fitzgerald in the vicinity of the 60th parallel of latitude, which is the boundary between Alberta and the Northwest Territories. These salt springs were visited by Sir James Richardson in 1820, and in the same year D. W. Harmon stated that " ... clown Salt river there are several places where almost any quantity of excellent dean white salt may be taken with as much ease as sand along the seashore" (3). One hundred years later, in 1920, when the writer first visited these springs, the "dean white salt" which had accumulated about the springs was about 400 tons ( 4). This paper deals with a thick deposit of rock-salt which has been proved by drilling in the vicinity of McMurray. Particular attention will be given to a well drilled at Waterways early in 1936 by Industrial Minerals, Limited, when a continuous bed of rock-salt was penetrated with a thickness of 199 feet. As this paper is being presented, a salt plant is being completed and a production well is being drilled at the plant. < is salt deposit is in the vicinity of McMurray, close to the junction of the Clearwater and Athabaska rivets, in township 89, range 9, west of the 4th meridian. McMurray is about 240 miles northeast from Edmonton. As shown on Figure 1, Clearwater river, which rises at Methy portage, in Saskatchewan, enters Athabaska river at McMurray. Some three miles above the mouth of Clearwater river, the Hangingstone enters from the southwest. Waterways, where the latest salt development has taken place, is situated at the end of the Northern Alberta railway, a distance of 304 miles from Edmonton. This railway reaches the bottom of the Clearwater valley at Draper station, about 3 miles east of Waterways and near the mouth of Deep creek. The Draper bituminous sand plant is approximately half a mile east of Draper station. About one mile south of the townsite of McMurray, Horse river enters the Athabaska from the east.

Jan 1, 1937

By Werner Unland, Nick Holl

"The paper presents the engineering design and experience gained so far with a dewatering system for an open-pit uranium mine planned at Key Lake in Northern Saskatchewan.The results of hydrogeological investigations preceding engineering exhibit an extensive unconfined overburden aquifer hydraulically connected with the underlying Athabasca Formation and basement rocks, both of relatively low hydraulic conductivity. The overburden aquifer is embedded in a bedrock trough, with the deepest depression between the planned pits. The hydrogeological data were used in a numerical dewatering model simulating groundwater flow atdifferent stages of the pit development.Based on the model results, the engineering design had to provide for different pumping rates, varying between 1.0 and 0.21 ms/sec. This problem was solved by using a double line pressure system. The design concept for the complete peripheral discharge system and the well design used for 26dewatering wells are discussed.Experience with reverse-circulation techniques applied for the construction of the dewatering wells is presented. Theoretical and practical considerations which led to the constructionof wells of different diameters are discussed.The design of the in-pit dewatering system provides for seepage ditches, horizontal drains, pit-bottom sumps and inpit dewatering wells where required."

Jan 1, 1980

By J-P. Rossetti, A. Guerin, M. Jaboyedoff, L. Baillet, A. Mariscal, J. D'Amato, D. Hantz

"The processes leading to the fall of rock compartments from rock walls are poorly known as well as their velocity. It ensues that quantitative prediction of the failure time for a rock compartment which is presently stable, is not possible by a purely geomechanical approach. However a quantitative probabilistic prediction of rockfalls at the scale of a rock wall is possible if the spatial-temporal rockfall frequency can be determined or estimated (Hantz, 2011). For a better knowledge of failure processes and frequency, rockfalls have been detected in several rock walls, using annual terrestrial laser scanning, allowing comparison of the frequencies in different geological conditions. For one of these rock walls, the spatial detection have been completed by a precise dating of the events, using a quasi-continuous photographic survey (one photo every 10 mn), allowing the study of the influence of meteorological factors.The precise dating of rockfalls has been carried out for the Saint-Eynard cliff which towers above a residential area of the town of Grenoble (French Alps). The South-East facing cliff consists in bedded limestone gently dipping North-West and located at an elevation between 850 m and 1100 m. The surveyed zone is about 750 m large and 250 m high. Between 01/02/2013 and 26/11/2013, 65 rockfalls ranging between 0.01 m3 and 20 m3, have been detected by diachronic comparison of laser scanner data and dated by comparison of photographic images. The temperature at the elevation of the cliff has been calculated from the temperature measured (every 5 mn) at a meteorological station located at an elevation of 245 m and 2.5 km away from the cliff, using a temperature gradient of 0.003°C/m (D’Amato et al., 2014). The precipitation were measured 900 m away from the cliff at an elevation of 469 m. Different meteorological conditions have been defined: (a) “freeze” qualifies days with negative mean temperature (but with a thaw period, except for two days); (b) “thaw” qualifies days with positive mean temperature, but following a freeze day; (c) “rain” qualifies days with precipitation.Table 1 shows the rockfall temporal frequency for the different meteorological conditions. It appears that the frequency is about 6 times higher the freeze days, 2.5 higher the thaw days and 3 times higher the rain days than days without freeze, thaw or rain."

Jan 1, 2015

By R. del Villar, A. R. Laplante

"This article presents four grinding simulation programs, written in Applesoft BASIC. The firs t two calculate residence time distributions (RT Ds) for open and closed loops mills. The third program calculates the select ion functions from the RTD, breakage function and particle size distribution (PSD) o f the feed and discharge. Two linear regression programs are also included to calculate the breakage function. These results are used in the fourth program to simulate continuous or batch grinding kinetics.The modelling approach presented is the size discrete, time continuous matrix formulation presented by Reid (1965) from concepts originally proposed by Epstein (1948). It is at the present time the most widely accepted phenomenological model of grinding kinetics and is standard textbook material (Austin et 01., 1982; Kelly and Spottiswood, 1982, p. 152). The concepts of RTDs and tracer testing originated from chemical engineering theory and practice, and are well presented in Leven spiel (2n d Ed . 1972 , Ch. 9) .Applesoft* was chosen because it is compatible with many micro computers. It is also one of the simplest and least powerful BASIC versions. Thus it can easily be adapted to other more complex BASIC versions.Open Loop Residence Time Distributions (Program RTDOPEN)As mixing, channelling, stagnation and short-circuiting all affect slurry motion in tumbling mills, transport characteristics are very complex an d cannot be derived from fundamental principles. Fortunately , as grinding follows first order kinetics, transport characteristics for the purpose of grinding simulation ca n be represented by the RTD of the slurry phase . It is normally determined using liquid tracers, as it has been demonstrated and is commonly accepted that in industrial ball mill s, the RTD of the so lid phase is particle size independent and equal to that of the liquid phase."

Jan 1, 1985

By G. Lucas

"Material substitution occurs continuously in response to competitive and economic pressures. Technical development can accelerate or slow substitution by improving the performance of the invading or defending material. The choices are seldom simple and have to be made in the context of continuous commercial change.The development and commercialization of a new aluminum material is examined. The material has been introduced into· several different markets, so it is possible to compare and contrast the degree of success obtained in each.IntroductionAluminum-based materials have been in use for over one hundred years and , therefore, the development of a new family of alloys is rare. In the early 1970s, Dr. L.R. Morris and his coworkers at Alcan&apos; s Kingston Research Centre started work on what was, at the time, something of a scientific curiosity-a family of alloys strengthened by an unusual mechanism.This paper deals with the development and commercialization of what became known as the Alcan 255 alloys"". These alloys have found uses in several markets, usually as improved substitutes for existing materials. Forecasting the usefulness of a substitute material in an existing marketplace is difficult, in part, because even material users are seldom able to specify precisely their requirements. This uncertainty can cause the failure of some substitutions but can also lead to opportunities which were not initially obvious.Technical BackgroundPure aluminum is a soft, weak material. It can be strengthened by the addition of various alloying elements and by work hardening. Alloying elements usually act by forming solid solutions which are stronger than the pure metal or by precipitating during heat treating or aging and so preventing the easy movement of dislocations during deformation. Elements which can perform either role had been investigated for decades and were thought to offer little chance of technical breakthrough in 1970. An outgrowth of the then new and exciting research on directional solidification seemed, however, to offer such promise.Some aluminum-iran-manganese alloys will solidify under certain conditions as &apos;coupled growth&apos; eutectics (Figs. I and 2). The microstructure shows one phase growing as long rods through the other. This is an uncommon structure and it was investigated to see if it had equally unusual properties. On deformation by rolling the rods were broken up into small equiaxed , evenly-spaced particles (Fig. 3). Materials with this structure were found to be stronger than other alloys with similar amounts of alloying addition, and to resist thermal softening remarkably well. This combination of properties was thought initially to be due directly to the particles by a dispersion strengthening mechanism, but later this was found not to be strictly true."

Jan 1, 1987

By B. W. Clyburn

"Coals from the Corporation&apos;s Lingan and No. 26 mines are classified as high-volatile A bituminous, with a very low inherent ash and containing a/l essential properties to provide metallurgical coal, with the exception of a high sulphur content. Only through proper cleaning at low specific gravity can the pyritic sulphur fraction of the coal be liberated to an extent where final sulphur meets coking standards. This first section of the paper deals with the operation of a Dutch State Mines heavy-media cyclone circuit to achieve an actual separation in the region of 1.30 specific gravity. A discussion of the parameter of control which must be applied along with an appraisal of the results obtained is included in the paper.IntroductionVery high fluidity and unusually low ash are the outstanding characteristics of coal from Devco&apos;s mines in the Harbour seam of the Sydney coal field.However, sulphur content, mainly pyritic, ranges from 1 to 2.5070. To obtain the low and consistent sulphur level required in metallurgical coking coals, preparation at low specific gravity is required .Metallurgical coke is used as the fuel in an iron blast furnace. Its sulphur content largely determines the quantity of slag required to remove it and therefore influences furnace productivity and unit costs.Typical data on the various coal properties of importance in the production of coke are included in Table I. Necessity of Low-Gravity SeparationThe design of any coal preparation plant requires the study of washability properties of the coal to be treated to determine the quantity and quality of coal produced at a given specific gravity along with the difficulty in accomplishing that separation.Their low ash content allows the important washability aspects of Harbour seam coals to be represented by sulphur! specific gravity curves (Fig. I). This particular example indicates that a yield of 54.5% is attained, at a sulphur content of 1.20%, for a perfect separating device operating with a 1.29 S.G. cut point.Material rejected from this separation still contains usable coal, which is recovered as middlings by separating at a higher gravity."

Jan 1, 1980

By J. Boulton

"Nuclear energy is an established and proven energy source. Today, CANDU-PHW nuclear-electric generating stations produce over one third of Ontario&apos;s total electrical supply: safely and economically. In many parts of Canada, where economic hydro resources do not exist or are fully developed, coal and nuclear energy are the only alternatives for future large-scale electrical generating capacity.Recent analyses have suggested that, in the f ace of increasing energy demands and decreasing reserves of hydrocarbon fuels, Canada must depend on electricity to provide an expanded fraction of its energy budget. Nuclear energy is likely to play an increasing role in the generation of electricity; there are also potential applications as a supplier of process heat in industry and in the in-situ recovery of bitumen fro m tar sands.The future supply of nuclear fuel, reactor safety and radioactive waste management are briefly discussed. In each case, the benefits to be gained from a controlled expansion in the use of nuclear energy outweigh any uncertainties which may exist."

Jan 1, 1981

By K. Ohto, B. B. Acihikari, H. Kawakita, M. Gurung, S. Alam

Two kinds of adsorbents were prepared from persimmon tannin extract to investigate their adsorption behavior of metal ions from hydrochloric acid solution; one was prepared by treating with concentrated sulfuric acid while another was prepared by immobilizing functional groups of quaternary amine. The former adsorbed only gold(III) and its maximum adsorption capacities was evaluated as high as 1510 g/kg while the latter adsorbed not only gold(III) but also palladium(II) and platinum(IV), the maximum adsorption capacities of which were evaluated as 820, 89 and 101 g/kg, respectively. For both adsorbents, practical adsorption of base metals was not observed.

Jan 1, 2011

By George J. Simandl, Suzanne Paradis, Kirk D. Hancock, Jana Simandl

Traditional prospecting and boulder tracing are the two most important field techniques used in exploration for magnesite deposits hosted by sedimentary rocks. Consequently, success depends largely on the prospector&apos;s ability to identify magnesite. A density agent called sodium polytungstate (3Na2W04·9WOj&apos;HPJ was successfully used to determine the presence of magnesite in sedimentary carbonate rocks of southeastern British Columbia. A rapid field method was developed and tested. This method permits discrimination between limy dolomites, dolomites, magnesite-bearing dolomites and magnesite-rich rocks.

Jan 1, 1993