Search Documents

By Turco E, Pelizza S, Vona A

Within the project against pollution in the Gulf of Naples (Italy) it was envisaged to build a sewage collection tunnel whose tunnelling section is about 30 m2 and whose length is over 4 km. The formations to be bored through feature heteregeneous volcanic deposits made up of either lenses or lava, lapilli and pozzolan layers and ashstone silts. The cover ranges between 10 and 30 metres. The surface is heavily built-up requiring then an accurate monitoring and reduction of noise, vibrations and settlements. The building of the tunnel is therefore carried out by means of a boom tunnelling machine equipped with a mechanized shield. Support along the complete excavation perimeter is provided by linerplates together with an immediate cement grouting behind them. At a later stage the concrete lining will be cast in place.

Jan 1, 1987

Access roads for haulage, construction or maintenance purposes are discussed with particular attention being given to the un- sealed "all weather" form of construction for Off-Highway applications. The service conditions experienced by the surfaces used in these roads is examined. These conditions are discussed in terms of the conventional engineering properties used for natural gravel material selection. Experience gained during the construction of a pipeline access track is used to illustratE material selection guidelines based on geological input and an understanding of good construction practices. TMITDnIll IrTT Ohl In many Australian situations off-highway haulage by wheel or track supported vehicles is carried on unsealed, gravel roads. Although the unsealed gravel road is the back-bone of the rural road network in Australia, in general, traffic loadings are relatively low compared to the off-highway unsealed haulage road. The cost of the haulage/access road construction component is one important factor in project planning which needs careful consideration. It is no longer acceptable that the initial rough exploration track be gradually upgraded so that it will eventually carry construction and maintenance traffic safely and efficiently. Fatal accidents and

Jan 1, 1982

By Angove JE, Johnson GD

Sulphide concentrates are produced in a wide range of mineral processing operations. In the case of base metals they are further treated by smelting and/or hydrometallurgical techniques. In the case of refractory gold ores, sulphide concentrates containing gold are roasted or oxidised by various hydrometallurgical processes. This paper discusses the development of the Activox(R) Process which can provide an alternative method for treating sulphide concentrates. This process consists of fine or ultra-fine milling, followed by mild pressure oxidation to produce solutions of base metals or to liberate refractory gold. Base metal solutions (eg of nickel and cobalt) can be further processed by solvent extraction and electrowinning, while refractory gold can be recovered by cyanidation. The economics of the Activox(R) Process are often better than alternative oxidation techniques.

Jan 1, 1993

By J Edman, RáBeamish, G Cambourn, B Beamish

Moist Adiabatic Benchmark (MAB) and R70 testing have been applied to core samples of a multiple seam sequence from a borehole at the Doyles Creek Project. The coal samples range in rank from high volatile B bituminous to high volatile A bituminous, with a general increase in coal rank as depth increases in the borehole. The intrinsic coal reactivity to oxygen decreases with coal rank as indicated by the R70 values. The time taken to reach thermal runaway shown by the MAB testing however is strongly modified by the interaction between the intrinsic coal reactivity, the moisture content of the coal and the retained gas content of the coal. This is clearly demonstrated by the lowermost seam of the sequence. The MAB test for coal from the Whynot Seam took 20 days to go to thermal runaway, which projects to heating issues taking between eight to 12 months to occur for loosely piled coal found in coal roof falls or a longwall goaf and uncompacted stockpiles, assuming sufficient air is available for coal oxidation. The results from this project illustrate leading practice for the operational planning and development of an appropriate spontaneous combustion management plan (SCMP).CITATION:Beamish, B, Cambourn, G, Lewis, G, Edman, J and Beamish, R, 2013. Application of leading practice spontaneous combustion assessment to exploration at the Doyles Creek Project, in Proceedings The Australian Mine Ventilation Conference , pp 293-298 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 1, 2013

With the advent of the mini computer and the relational database project management has experienced a new lease of life. The project manager no longer has to wait days for his reports, and he doesn't have to thumb through a foot of four part stationery to find that one line of information. The new techniques bring characteristics that are music to the ear of the project team giving them a better chance of bringing the projects in on time and within budget.

Jan 1, 1983

By P M. Dight

Shotcrete usage in declines and developments has become pervasive as operators strive to achieve production improvements. Issues of mix control, fibreload, thickness control, temperature and curing conditions all play a part in the quality control. Often to overcome some of the quality control issues designers over specify the strength requirements in order to meet their operational constraints. Adherence to the standard civil testing requirements of 28 days moist cured at 21ºC without properly calibrating these results to the changing environment underground leads to contractual disputes. There are a number of standard tests specified including cylinder tests, cored tests, beam tests and round determinate panel (RDP) panel tests. The logistics of storing these samples and then transporting them to concrete testing laboratories without due regard to temperature changes with time can influence the results. All the samples can be readily handled by personnel except the RDP panel. The standard RDP panel is 800 mm diameter by 75 mm thick and requires an ITH machine at the mine and a fork lift at the laboratory to move it around. This paper will examine the possibility of a panel which provides scalable results to the standard RDP panel but can be easily handled by personnel and/or tested on site with suitable equipment. This allows for faster turn around and better quality control for the sample prior to testing. This enhances the identification of quality control issues at the mine and improves safety.

Mar 21, 2011

By T Purvis, Z Liu

Ernest Henry mine (EHM) is an underground sublevel caving mine located in north-west Queensland with a production rate of 6.4 Mt/a. The mine has sublevels spaced with a 25 m vertical interval. The production process on each level starts with the drilling and firing of a blind uphole rise to start the slot extraction. These rises are fired as a single shot and routinely need to achieve a design height of 22 m to 30 m depending on the local mine geometry. If the rise fails to perform as designed then the production phase of the level is delayed with significant rework required to remedy the situation.This paper describes the process that the EHM team has followed to improve the first time performance of each rise. The improvement process commenced with a review of results from previous rises and resulted in the identification of a number of improvement opportunities. A revised holistic approach was established for the process, which included involvement from operators and engineers. Through continued measurement and review of rise performance, inputs to the process were improved to a point where reliable results can now be expected. The successful performance of subsequent rises has been verified through a comprehensive quality assurance quality control (QA/QC) program. Before quality control processes were implemented, the success rate of blind uphole rises was only 11 per cent (one out of nine rises) at EHM. In comparison, the success rates have been vastly improved to 25 per cent (one out of four) and 75 per cent (three out of four) respectively following two stages of improvements. This paper concludes with the ‘current’ series of best practices used at EHM and recommendations.CITATION:Purvis, T and Liu, Z, 2017. Improving the performance of blind uphole rises at Ernest Henry Mine – a case study, in Proceedings 13th AusIMM Underground Operators’ Conference 2017, pp 335–340 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 16, 2017

By M Hino, D R. Swinbourne

The thermodynamic properties of arsenic in metal, speiss, matte, slag and gas phases are first summarised in this paper. Arsenic associates with sulphide minerals and generally has compounds of high volatility, but it has a weak affinity for sulphur and a strong affinity for metals, especially copper and iron. In the initial stage of the oxidation of sulphide concentrates arsenic is volatilised easily prior to the oxidation of FeS, although it tends to be fixed in the condensed phase as FeAsO4 if the concentrate is over-oxidised. Thermodynamic simulation of oxidative copper smelting reveals the distribution of arsenic between matte, slag and gas, and the possibility of condensation of arsenic from the resulting waste gas is discussed. In reductive smelting more arsenic remains in the metal or matte, and is sometimes concentrated as a separate speiss phase. The phase relations and thermodynamic properties of speiss are also summarised briefly. Arsenic refining from smelted copper metal is shown, from an examination of the basic principles of arsenic removal into slags, to be difficult. Owing to its weak affinity for lead however, arsenic refining from lead bullion is seen to be much easier.

Jan 1, 2000

By S Hapugoda, J R. Manuel, M J. Peterson, A Poliakov, E Donskoi

################

Aug 12, 2013

In underground ore mining of copper ore, lead-zinc ore, tin ore and fluorspare in German Democratic Republic geological situation is characterized by ore deposits of small thickness and great variability of ore grades and mining conditions. For long range mining strategy and short-term planning of production a model was developed fitting to make optimal economic mining decisions. Starting point of the model is a cost function representing all direct costs per unit recoverable metal in concentrate for each stoping unit (ore reserve block). In the costs function the results of regression analysis of ore grade and metal recovery in concentration plant were considered. All stoping units (ore reserve blocks) of a mine were arranged to growing direct costs. The relationships of recoverable metal, ore tonnages and corresponding costs were plotted in a diagram. The data processed by- computer and the graphic representation of the results make possible 1. economic evaluation of stopes and ore reserve blocks, 2. estimation of cut off grade, 3. optimization of works planning.

Jan 1, 1977

Chile, which hosts around 30 per cent of the worldÆs copper resources, is now the largest producer and exporter of copper. Chilean copper output accounts for more than one-quarter of total worldwide production. An increase to around 40 per cent is forecast by the end of the century. In addition, Chile ranks eighth in silver production and 11th in gold output. In Chile, mining generates more than eight per cent of the countryÆs GDP and the total value of mineral exports is more than US $7.85 billion corresponding to more than 25 per cent of South AmericaÆs mineral production. The rate of growth of Chilean mineral production is indeed impressive. Table 1 shows that in the period 1969 - 1998, copper annual production increased 564 per cent from 667 000 t to 3 764 000 t. Gold production went up 27 times from 1827 to 49 770 kg. Silver output grew 1219 per cent from 95 650 kg produced in 1969 to 1 166 380 kg in 1998. Several facts explain this dramatic increase of production, but the most important was the success of exploration sustained over the same period. This resulted in the discovery of several world-class deposits which when developed into mines, account for much of the production increases. Therefore, this summary review shows the success of basic exploration carried out during the last 30 years in the Chilean territory. The review is based on data already published in different specialised mining books or magazines. It only includes those world-class discoveries not the lesser discoveries important at local scale. All figures were calculated using 1998 $US dollar and average estimated metal prices valid for 1999: copper $US 1653 per t ($US 0.75 per pound), gold $US 9452 per kg ($US 294 per ounce) and silver $US 177 per kg ($US 5.5 per ounce).

Jan 1, 1999

By R Williams, P Kohout, J Comins

The Northside Storage Tunnel (NST) is the largest tunnelling project ever undertaken in Sydney. The tunnel extends deep underground from the western bank of the Lane Cove river to the North Head sewage treatment plant (STP), with a branch tunnel from Scotts Creek connecting to the main tunnel under Tunks Park. The aim of the tunnel is to intercept wet weather overflows from four key points along the northernsuburbs ocean outfall sewer (NSOOS) and provide short-term storage and transfer of sewage to NorthHead STP for treatment prior to discharge to the ocean through the deep ocean outfall. The project was an ambitious undertaking by an alliance between the client Sydney WaterCorporationand the engineering firms of Montgomery Watson, Connell Wagner and Transfield to design andconstruct approximately 20 kilometres of tunnel, tunnel declines and shafts in just over three years. In order to achieve this tight timeframe construction of the NST has been undertaken simultaneously at seven construction sites located across the northern suburbs of Sydney. As with most tunnelling operations, tunnel boring machines (TBMÆs) and roadheaders dominated the excavation activities. Tunks Park and North Head STP are the major tunnelling sites. An access decline was excavated using roadheaders at both of these sites to facilitate tunnelling using TBMÆs. Three TBMÆs 3.8 m, 6.0 m and 6.3 m diameter) were launched from Tunks Park and one TBM (6.5 m diameter) was launched from North Head. At the overflow interception sites of Scotts Creek, Lane Cove River and Quakers Hat Bay two vertical shafts known as drop and access/ventilation shafts were constructed. These shafts would provide the linkage between the existing sewer and the tunnel. As their names suggest the drop shaft would convey the wet weather sewage overflows to the tunnel while the access/ventilation shaft would provide access during dry weather and ventilation during a filling event. The fourth overflow site of Tunks Park would use the tunnel decline as its link to the tunnel. Originally these shafts were to be excavated using the raise bore method. This technique however, is entirely dependent on the TBMÆs reaching the shaft locations at the specified time. This was not the case at two of the three shaft excavation locations and top down methods of excavation such as, a percussive cone fracturing (PCF), blind bore, mechanical excavation and drill and blast were investigated to ensure the project met its completion schedule. Traditionally project decisions are dominated by cost and schedule objectives. The contractual arrangement of the Alliance however, required that the objectives of safety, community and environment also be considered in any decision making process. Thus each of these top down methods of excavation were assessed against these five objectives. On considering all of these factors the use of explosives was considered to be the superior technique.

Jan 1, 2001

By Loo R

The Paper discusses the size and extent of in-pit dust suppression problems created by iron ore mining in the Pilbara region of Western Australia. Dust problems associated with drilling, loading, hauling and tipping are discussed indicating the large quantities of water which can be applied for dust control and attempts that have been made to rationalise this water usage to obtain maximum benefits from the applied water. The magnitude of the problem and the quantities of water involved can be appreciated when one realises that 275 000 tonnes of rock are moved on Mt. Whaleback each day and that there are 40 km of haulroad within the open pit. Initially dust suppression was limited to the spraying of haulroads by large water tankers. Now dust suppression is practiced during drilling and after blasting, wind blown dust is reduced by application, using water cannons,of large quantities of water to floor stocks prior to loading operations as well as by the installation of 16 km of automatically controlled fixed sprinkler reticulation on the main semi-permanent haulroads. The methods used to assess the water requirements for in-pit dust suppression are discussed and the extensive development testing used to evolve the present installations are 1. Environmental Superintendent Mt. Newman Mining Co. Pty. Ltd. Newman, W.A. 2. Chartered Consulting Engineer, Perth, W.A.

Jan 1, 1979

By J Karlovšek

Civil engineering infrastructures are often subjected to different types of natural and mechanical activities. These influences may result in serviceability or even in stability of structures due to material deformations, increased water content within the materials used or the formation of internal or adjacent cavities that may threaten the infrastructure. Construction practices can lead to development of such defects in the form of cavities. In civil engineering it is crucial to detect these variations in material properties and to detect the presence of defects. However, as they are often hidden from view, these attributes may be difficult or impossible to target with traditional testing methods. For these reasons rapid geophysical methods, such as ground penetrating radar (GPR), are increasingly being used. At the University of Queensland (UQ) GPR is used for detection of voids and cavities which have been caused by an over excavation of the earth pressure balance machine (EPB) operating in a closed mode.A variety of numerical simulations using the finite-difference time-domain (FDTD) methods and preliminary experiments have been carried out in order to specify information about the nature, type, size, location and other characteristics of targets to be detected by GPR. In doing this the difficulty of interpreting GPR data, which is mainly due to the complexity of the factors involved in multiple possible solutions of the observed features, can be overcome.

Mar 8, 2011

By C Harwood, EáWestman, K Luxbacher

Testing of in situ seals in underground coal mines is critical to determine seal integrity and to provide safe working conditions. In the wake of the 2006 Sago Mine explosion, the United States of America (USA) promulgated the Mine Improvement and New Emergency Response (MINER) Act (USDOL, 2006) which required mines to install 827 kPa (120 psi) rated seals or monitor and maintain the atmosphere behind existing 345 kPa (50 psi) seals. The purpose of developing the regulations was to prevent the breaching of seals in the event of an explosion in the sealed area.While seal design and construction is carefully regulated in practice, the construction of seals is difficult to monitor, as many are constructed under various mine conditions and the methods rely on prescribed placement of the seal material. Further examination of installed seals is limited to two-dimensional visual inspection and atmospheric and convergence measuring devices. These methods do not accurately reflect the integrity of the seal and cannot detect changes, deterioration, or defects within the seal.If detection of defects, deterioration and damage is not possible, unexpected communication between the active and sealed areas may result. Additionally, the ability of the seal to withstand explosions may be compromised. Non-destructive testing (NDT) of underground mine seals is necessary to investigate if the seal properties have been altered and if the seal remains functional as a barrier between active areas and sealed areas of the mine. This paper gives a preliminary assessment of proposed NDT methods for seal evaluation using radio frequency (RF) technologies and tracer gas methods.CITATION:Harwood, C, Luxbacher, K and Westman, E, 2013. Non-destructive testing of in situ underground mine seals - Initial technology assessment, in Proceedings The Australian Mine Ventilation Conference , pp 299-306 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 1, 2013

By M Davies, G Theletsane, A H. Gray

Recovery of gold from gold ores has been driven by the available technology and its configuration in the process plant flow sheet.Conventional practice in test work programs has the ore being ground fine (to 106 or 75 microns) to ensure liberation ahead of leaching or flotation. This paper identifies that, in many cases, gold and gold sulfide carriers will liberate and be recovered to a concentrate at much coarser sizes.There is an exponential increase in energy consumption relative to particle size reduction. This impact becomes extreme when comparing crushing a product to 1 mm against grinding to 75?microns.The resultant reduction in energy consumption when liberating and separating at 1 mm or coarser compared to grinding to 75 microns can be in the order of 15 kWh/t or 60 per cent of energy in the comminution circuit.Recovery of free gold and gold sulfide carriers by preconcentration (using continuous gravity devices such as the InLine Pressure Jig), combined with flotation of the fine gold and gold carriers, can result in significant power savings.There are multiple locations within the flow sheet that can be targeted using this process, including recovery in the cyclone underflow of existing plants, preconcentration ahead of the plant or complete greenfield, low-energy process plants designed from first principles based on data from a Gekko developed test work regime.We will describe the process of defining mineralogy in the laboratory and the decision-making process through to actual applications in the field.Several examples will be provided, including a South African Witwatersrand gold ore, several Australian gold ores and others, indicating the benefits of this process and where it has been brought to commercial reality.CITATION:Gray, A H, Davies, M and Theletsane, G, 2014. Coarse liberation and recovery of free gold and gold sulfide carriers for energy reduction in process plants, in Proceedings 12th AusIMM Mill Operators’ Conference 2014 , pp 117–128 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 1, 2014

By S Norman

The Water Delivery Alliance (WDA) was established to design, construct and commission the pump station and desalinated water delivery pipeline to link the desalination plant on the Kurnell Peninsula (constructed by others) with the existing distribution network at Erskineville, Sydney, Australia. The WDA consisted of McConnell Dowell Corporation Ltd (Macdow), Bovis Lend Lease Pty Ltd (BLL), Kellogg Brown and Root Pty Ltd (KBR), Worleyparsons Ltd (WOR), Environmental Resources Management Group Inc (ERM) and Sydney Water Corporation (SWC).Sydney’s Desalination Project is one of the initiatives to secure Sydney’s water supply against the effects of climate change, population growth and drought. The desalination plant, 100 per cent powered by renewable energy, can supply up to 250 million litres of water per day (mld), which is up to 15 per cent of Sydney’s water needs. The project involved the construction of an 18 km pipeline with an ultimate capacity of 500 mld to accommodate any future increase in the output of the desalination plant.The Alliance procured three full-face tunnel boring machines (TBM) from Herrenknecht AG to construct the 6.5 km of tunnel that would provide a conduit for the DN1800 welded mild steel cement mortar lined (MSCL) pipeline at a number of locations along the route. Nineteen shafts and 16 tunnels were required to complete this work.Crucially one of the TBM drives involved construction of a tunnel into Botany Bay under protected marine life habitats; enabling the connection of the MSCL water carrier pipeline into the dredged section of pipeline underwater, approximately 800 m off-shore in Botany Bay.This paper details the retrieval of the 17.4 m long TBM from the ocean floor upon completion of the Botany Bay tunnel allowing for subsequent use on the Project. Elements covered in the paper include the 835 m tunnel, design and construction techniques for the tunnel and recovery, and details of the methods used to install the DN1800 water carrier pipeline.

Mar 8, 2011

By Mann LD

The Haveluck gold deposit, located 2.5km north of Meekatharra, contained 1,284,000 tonnes at an average grade of 1.8 g/t gold of drill delineated proved and probable ore prior to commencement of production. Following successful laboratory and pilot scale testing a decision was made to establish a 300,000 tonnes per year heap leaching operation. The ore, crushed to minus 100mm was stacked on an impermeable membrane and irrigated with a dilute cyanide solution. Gold was recovered from the resulting pregnant solutions by adsorption onto activated carbon and gold bullion produced in a modified Zadra process desorption plant. From the commencement of mining it was obvious that a high percentage of fine material was being produced which would adversely affect the percolation of the cyanide solution-through the leach heaps. A screening plant was incorporated into the crushing circuit which provided an oversize product satisfactory for heap leaching and an undersize for carbon-in-pulp treatment. Plant design provided for the slurrying of minus 0.8mm ore before feeding to the pachuca tanks. Initial practice was to use four tanks for gold dissolution and two for carbon contact. Vibrating screens were used through- out for the carbon-ore separation and the loaded carbon was stripped in the existing desorption plant.

Jan 1, 1982

By E Ferrow, R Herbert, M E. Malmstr, M Fuchs

The study of microbial sulfide oxidation and oxidation rates of tailings requires the use of sterile control samples in laboratory experiments for comparison purposes. The need for sterile tailings sand is also apparent in the study of microbial communities and processes. This study compares six different methods with regard to sterilisation efficiency and investigates chemical and mineralogical changes in the samples as the result of sample treatment. In addition, the effect of sterilisation on mineral weathering rates is also studied. The efficiency of the different methods with regard to sterility is estimated by most probable numbers (MPN) of both sulfur and iron oxidising bacteria. The sterilisation methods that were compared are: washing with sterile water, washing with ethanol, applying antibiotics, repeated heating to 70¦C, autoclaving, and γ-irradiation. There are several possible drawbacks with the different methods, including the risk of an applied chemical acting as a substrate for micro-organisms in the system, and the risk of altering the tailings. The results show a substantial difference in sterilisation efficiency between the treatments. For example, autoclaving, repeated heating, ethanol and irradiation efficiently kill micro-organisms, rendering an undetectable amount of bacteria after one month of incubation, whilst washing with water exhibits virtually no microbiological effect, with a bacterial content comparable to the control. The use of antibiotics for sterilisation ranks intermediate: the lag-phase was twice as long in the antibiotics treatment compared with the controls. X-ray diffraction, optical and electron microscopy, M÷ssbauer spectroscopy, and mineral magnetism indicate no significant change in the bulk mineralogical composition. However, X-ray photoelectron spectroscopy analyses show that with some of the treatments, sulfides are partially oxidised, as indicated by the formation of sulfate and partially û oxidised sulfur species at the tailings surfaces. Aerated batch weathering experiments performed on sterilised tailings samples and untreated controls indicated that while the initial rates of element (S, Fe, Cu, Zn, Mg, Na, K, Ca) release may differ between the samples, over the course of ~100 days of experiment at pH 2 and room temperature, the rates declined toward a similar value for all samples. To conclude, there does not appear to be one perfect method for tailings sterilisation. Autoclaving and heating damage the mineral grain structure and oxidise the sulfide surfaces. Ethanol, antibiotics and rinsing greatly alter the pore water chemistry through the washing procedure. In addition, ethanol and denatured antibiotics might serve as a substrate and also, in the case of antibiotics, adhere to mineral surfaces thus obstructing chemical reactions. Irradiation seems to be the preferable method on an overall basis, although the formation of surface Fe3+ was suggested by M÷ssbauer spectroscopy.

Jan 1, 2003

Industrial minerals and rocks (alternat ively called non-metallic minerals) are those- which are economically important because of their desirable physical or chemical properties rather than their metal or energy content. They are divided into nine classes: structural, pig- ments, process aids, ceramics and refractories, chemical source minerals, abrasives, foundry minerals, gem stones, electrical minerals. Development of deposits is influenced by the dominance of marketing,by the required range of products, the-need for specialized process- ing, place value, and the transportation and distribution of high-bulk, low-cost commodities. Evaluation is different from that of base metals because of differences in geological occurrence, sampling methods, testing, treatment, placing a money-value on the material and the importance of export markets.

Jan 1, 1973