Search Documents

By S M. J Koleini, F Hedjazi

The purpose of this research was to study the calcination of lead-zinc flotation tailings from the Angouran lead and zinc flotation plant in Iran as a pre-concentration step prior to hydrometallurgical processing of the oxidised tailings. There is an abundance of these tailings in the Angouran region and making use of these tailings would help preserve national wealth and also reduce the serious problems of environmental pollution caused by the tailings. At the optimal conditions of calcining at 750 - 800¦C for 45 minutes, the sample showed a mass loss of about 19 per cent. Mineralogical analyses showed that under these conditions the carbonate minerals including smithsonite (ZnCO3), calcite (CaCO3) and dolomite (Ca Mg (CO3)2) decomposed to their respective oxides. Hemimorphite (Zn4Si2O7 (OH)2.H2O) converted into willemite (Zn2SiO4) and this transformation postponed the formation of silica gel in the leach solution. The grade of zinc increased from 22.20 per cent to 29 per cent. These mineralogical changes resulted in desirable reactions in the acid leach process.

Jan 1, 2004

Mining of the silver-lead-zinc orebodies at the George Fisher Mine officially started in 2000. A review of mining performance to date shows that many of the extracted primary stopes have experienced some degree of hangingwall dilution. The degree of hangingwall failure in the stopes became progressively more extensive throughout mining of the orebodies in 2001 and 2002, culminating in the unplanned catastrophic failure of the 744D stope in which the ore between 13C (2683RL) and 12L (2714RL) sublevels caved into the previously mined cavity between 13L (2654RL) and 13C sublevels. This was followed several months later by another unplanned caving event in a nearby stope, 740D. As a direct result of these unplanned failures it was decided to mine the stopes with a smaller span than had been previously planned and in a primary-secondary pyramidal stoping sequence. To limit the exposure of the stope hangingwall, a hangingwall drive is no longer developed and therefore geologists no longer have access to the detailed geological information that this provided. Geologists at George Fisher Mine have had to be adaptable and flexible in response to these proposed changes and rely more on data from drilling than mapping for their geological interpretation. The result is that the drilling cycle has become much more critical in the planning process.

Jan 1, 2003

Basic premises for evaluating special characteristics of gold-bearing porphyry metal systems stem from their contrasts with properties of the class as a whole. Included features are differences in geologic, thus tectonic, environments, subtle but real differences in the proportions of accessory metals Mo-Ag-Au that are regionally and within some regions, tempo-rally distinct, contrasts in the Ag:Au ratios, petrological-geo-chemical as well as isotopic differences between intrusive suites, the age and nature of host terranes, contrasts in alter-ation style, and zoning variations of mineralogical and physical properties of rocks. These properties are linked in various ways in different regions and suggest that in large gold-bearing systems where gold may be uniformly distributed, environ-ments of emplacement, and compositions or sources of igneous "progenitors" may dominate in importance over processes, and that systems in which gold is zoned are processes-dominant.

Jan 1, 1990

The State of Western Australia has a land area of 2 525 000 km2, and is well endowed with minerals and petroleum products. In 1989 - 90 these products were valued at nearly A$10 500 million.

Jan 1, 1992

By W R. Adamson

"Optimisation of drill and blast design and engineering can deliver a significant positive impact on the profitability of any mining operation; however, true engineering of the blasting process is less common than might be thought. The paper that follows explores this gap and suggests a process control-based approach to the challenge.The concept of applying modifications to drill and blast designs in order to achieve efficiency improvements in downstream mining processes is far from new. However, the author suggests that the practical application has become less than rigorous in a number of different sectors of the mining industry in a wide range of countries.There is a common tendency for the design process to become simplified to the point where the objective is merely the communication of instructions to field implementers (drillers, explosive suppliers, blasters, etc). In effect ‘design’ often degrades to ‘cut and paste’ with consequences that vary from mild to critical, with respect to the profitability of the business.Engineering of the drill and blast process involves the design function, not on a one-off basis but rather as a component of a more complete cyclical process that includes a statement of objectives, a design based on a suggested hypothesis, field measurement of results, comparison with the target ‘set point’ and the application of control measures followed by new measurement, including interpretation of the results in financial terms.When applied in this fashion, engineering provides practitioners with the means to optimise the drill and blast impact on the full spectrum business result of the mining activity.These concepts are discussed with reference to a surface gold mining operation applying run-of-mine heap leach extraction. Engineering optimisation by adapting process control and measurement techniques is demonstrated to be a key component of the solution set applied to generate enhanced operations productivity and stakeholder value. It is shown that a combination of rigorous measurement, model calibration and hands-on quality assurance/quality control facilitates the creation of a road map to profitability, stressing the need to consider economic trade-offs between operational expense (investment) and measurement of enhanced value (return on investment).The process, however, does not cease at this point. Implementation of true design practices, incorporating innovation and discipline in implementation or execution can drive the process to deliver demonstrable, technically validated outcomes. Furthermore, these technical results can be related to financially quantifiable impacts. However, this accomplishment does not guarantee that these gains or savings will reach the bottom line of those mining, quarrying and construction companies that begin the process with such high hopes.CITATION:Adamson, W R, 2015. Application of engineering discipline and a full-process optimisation focus – productivity to profitability without profuse pruning, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 3–12 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Aug 24, 2015

By H P÷llmann

Calcium aluminates, calcium aluminate ferrate and calcium aluminate sulfate were synthesised by solid-state reaction, sol-gel method, a self-combustion method and by a polymeric precursor process. For chemical sintering methods the base chemicals CaO, CaSO4, Al2O3 and Fe2O3 were used. As precursors for sol-gel synthesis metal nitrate hydrates and Al2O3-Sol were used. In order to synthesise pure phases by a self-combustion reaction glycine was used as fuel and nitrates as metal components. In the polymeric precursor process metal nitrates and diluted H2SO4 were used as metal components and the resin was made using citric acid (C6H8O7) and ethylene glycol (C2H6O2). Precursor phases synthesised by these different methods were sintered step-by-step in order to investigate the crystallisation. Further on single phases were hydrated and their hydration behaviour was studied by heat flow calorimetry, X-ray diffraction and cryo-transfer scanning electron microscopy. Due to the different synthesis procedures different hydration reactions and microstructures of the phases will be shown.

Jan 1, 2008

By A C. Chieregati, A Heberle, F L. S P Villanova

Since the publications of Gy’s initial work, many authors have discussed the approaches to estimate the variance of the fundamental sampling error (FSE). Experimental tests suggested by Pitard and François-Bongarçon determine the sampling parameters K and a to calibrate Gy’s formula. The heterogeneity test and the sample tree method are well known and broadly used for many commodities. However, prior to the analysis, the collection of a representative sample is an intriguingly difficult task. The composite for the heterogeneity tests often consists of run-?of-?mine material or processed ore on a conveyor belt. In most cases the final sample does not have enough mass, mixes different geological units, represents a rare blend and does not characterise the deposit. In order to obtain a reliable composite for trace elements and low-grade ores, sampling practitioners suggest at least half a ton of material.To prevent the common representative pitfalls in the FSE, this case study focuses on a single gold-?bearing geological unit collected in situ. With this unit being structured by the mine geologists, but with the interaction between engineers and chemists, it was possible to validate the reconciliation suggested by Pitard (2015). The heterogeneity test and the sample tree method were performed using 500 kg of a smoky quartz from a single geological domain and the results were compared to Gy’s formula. The logging practice by the geologists was modified, emphasising the definition of the size of the gold nugget or its cluster, number of grains and association. Finally, a mineralogical study was conducted on the geological unit to define the liberation factor. All the information is compiled in this paper, showing the need to fully understand the mineralisation to correctly define representative samples and proper analytical techniques.CITATION:Villanova, F L S P, Heberle, A and Chieregati, A C, 2017. Heterogeneity tests and core logging – a final reconciliation, in Proceedings Eighth World Conference on Sampling and Blending , pp 107–114 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2017

An extensive railway construction prog- ram in the People's Republic of China has required the excavation of many tunnels in difficult ground, particularly in mountainous regions. Conclusions drawn from case histories permit guidelines to be formulated as to the optimum location of tunnel alignments in faulted and folded terrains, and also in karst regions. Geological factors adversely affecting durability of tunnel linings can be minimised by adoption of appropriate construc- tion practices.

Jan 1, 1987

Changes in mining technology have led to an increase in the number of underground sulfide dust explosions reported in Australian and overseas mines. Samples collected at the Elura mine consisting primarily of pyrite, pyrrhotite, arsenopyrite, sphalerite and galena, were tested in 8 litre explosion chamber. The dusts were found to be capable of producing dangerous dust explosions with maximum explosion pressures of 440 kPa and rates of pressure rise of 5200 kPa/s. The hazards of a sulfide dust explosion are associated with the pressure wave and flame front of the explosion and the toxic gases remaining after the explosion.

Jan 1, 1984

The accurate determination of trace level gold in ores, metallurgical samples and process solutions is required because of the value of gold, the efficiency of the cyanide leach process and because of the high gold recovery from these cyanide solutions. It is thus necessary to routinely analyse geological and metallurgical samples with gold concentrations of 3 g tonne (ug g- 1ppm) and process solutions with a gold concentration of 0.01 mgL 1 (ppm) preferably with sufficient accuracy to quote at least two significant figures. Several techniques have been reviewed for their suitability for the routine gold analysis of these samples which also contain signif- icant concentrations of other ions. The classic fire assay technique has achieved the respect and confidence of mining personnel because of the results achieved by very experienced assayers. Other extraction and concentration techniques have now been shown to be equally effective. The use of instrumental analytical techniques particularly atomic absorption spectrometry have shown that cheaper procedures, which are as reliable, are now available to gold producers for the routine analysis required to maintain an efficient gold recovery process.

Jan 1, 1982

We operate a 50 cubic metre per hour mobile alluvial tin mine on small scattered deposits in the Irvinebank area. Wash is loaded by a Cat. 950 front end loader into the bin of a screening section and screen undersize is pumped to a separate jig unit. Both units are rubber tyre mounted and are shifted once a month when the haul distance gets to about 150 metres. The shift takes about 8 hours.The screening section is sited close to the face with a ramp for dumping in and a one metre drop for the screen oversize which is removed by the loader.A reciprocating plate feeder with variable rate hydraulic drive, feeds wash onto a horizontal 1.2 metre x 2.2 metre two deck Kinergy screen. Minus 10 millimetre undersize is pumped by a Warman 6/4 sand pump with a 37 kW variable speed Reeves Motordrive to the jig unit.The jigs are placed 20 to 70 metres away so that tailings will run back into previously mined ground. Reject stone is used to impound the sand and mud, allowing the water to filter through and return to the feed water pump.An MTE trapezoidal module is used as a primary jig. Hutch product is pumped to an eight cell clean-up jig which we developed ourselves along MTE lines. It has a trapezoidal shape and sawtooth stroke provided by cams. Clean tin is taken from the first four spigots. These consist of clear plastic tubes fitted with taps so that there is no water loss except when the tin is drawn off. Fine concentrate from the last four spigots is put over a curvilinear table which sits on a steel base packed with earth.

Jan 1, 1986

Roasting of zinc concentrate at the Risdon Works of the Electrolytic Zinc Company of Australasia Limited, (E.Z.), is carried out in two fluid bed roasters capable of treating 450000 tonne/yr, or sufficient for the output of 220000 tonne of salable zinc. The furnaces were constructed by Lurgi, Australia, to the basic design developed by Vieille Montagne Company of Balen, Belgium. The advantages of fluid bed roasting include a higher metallurgical efficiency in sulphur oxidation from a feed which does not require any pre-grinding, mechanical reliabil- ity through the absence of any moving parts within the furnace and the capability of being scaled up to a large unit.

Jan 1, 1977

By P Klaric

Drive stability is critical in block/panel cave mining. The production levels of these mines are required to remain operational for the entire life-of-mine which can be in excess of 30 years. It is therefore necessary to produce high-quality drives to ensure sustainable mine productivity. In order to improve the quality of drives and pillars, this gold mine instigated a project to optimise their development blasting. The initial aim was to reduce the level of overbreak in development mining, which was averaging approximately 18 per cent. The benefits of controlling overbreak not only included an increase in the integrity of the drives but also a decrease in load and haul and ground support costs. Through focusing on the optimal blasting of the perimeter holes, overbreak was reduced to 4.5 per cent. The project’s focus then moved to drill and charge designs for development faces. In optimising these designs, it was anticipated that improvements in the development mining cycle would be achievable.CITATION:Klaric, P, 2015. Improving drive stability through efficient development blasting design and practices, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 327–332 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By P M. Larionov, V I. Zaikovskii

Transmission and scanning electron microscopy together with X-ray spectral microprobe analysis were used to investigate the structure and chemical composition of pathological calcified formations on the bioprostheses of heart valves. Controllable synthesis was carried out under the conditions (T = 37¦C, pH = 7.4) when the ion composition of the main elements (Ca, P, Mg and NaCl) is close to their concentrations in blood plasma. It is proposed on the basis of the obtained results that the formation of the hydroxyapatite of calcific inclusions on bioprostheses occurs as a result of spontaneous precipitation in the blood plasma. One of the factors determining the formation of massive calcified bodies on the bioprostheses of heart valves can be decreased magnesium concentration in blood.

Jan 1, 2008

DCF Valuations are very important to individuals and companies involved in the mining industry. Such valuations are critical to investment decisions in relation to new and existing projects. In particular they provide fundamental information to shareholders in the event of a capital raising or takeover and to financiers supporting mining companies and projects. Also, DCF Valuations are often used to support asset carrying values in the financial statements of mining companies. This paper presents a Chartered Accountant's (CA's) perspective on the main issues to be considered in preparing, analysing and relying upon DCF methods in mineral valuations and provides some practical examples relating to key issues. The paper makes the important point that DCF methods involve making assumptions about future events and circumstances that inherently contain uncertainty which results in a valuation prepared on a DCF basis providing a range of values that are not perfect or accurate. In order that DCF valuations provide meaningful information the underlying methodology used and assumptions made must be consistent, sound and well supported. Credibility of those involved in preparing mineral valuations is vital and this paper supports the adoption of sound practices by all concerned.

Jan 1, 1994

The Inglewood Gold Project consists of several titles in and around the Inglewood and Wedderburn Goldfields which were purchased from Strata Mining Corporation (now Excalibur Mining Corporation). The Inglewood goldfield has a historical production of approximately 160 000 tonnes at 23 grams per tonne. The company has reopened and developed the Maxwells reef, picking up a high-grade shoot (Max Shoot) identified and worked by Goldquest et al up until 1994. Production ceased on a low gold price, rapidly reducing vein size and a requirement for further development. Greater Bendigo Gold Mines Ltd (GBM) has undertaken the development and encountered the mineralised vein in an increasing size setting with high grades and the existing mine development has access to a further shoot to the north (Max North Shoot). The Maxwells reef also contains the Woolf shoot south of the Maxwells shaft and an inferred resource of ~20 000 ounces is contained from 60 m below surface. Best intersection 2.9 m at 50 g/t. The Maxwells reef area produced approximately 20 per cent of the Inglewood goldfields production and GBM is preparing to increase its exploration efforts across the rest of the field. A processing plant has been constructed at the Maxwells mine site, which is capable of treating tailings, hard rock and alluvial material utilising gravity recovery. The existing Maxwells tailings have been excavated and treatment commenced. It is intended to produce a sand product from the tailings for resale and to reduce the storage requirements per tonne. Several large water dams constructed by Goldquest in the 1990s are being re-engineered to enable storage of significant tonnages of tailings. A level of surface and underground production is planned for 2008 and this is to be expanded into 2009 and beyond. The long-term future at Inglewood is envisaged as structural repeats at depth below the current workings and a project plan to gain deep access will be prepared on successful drilling results.

Jan 1, 2008

By B Indraratna, A Dey

The surface geometry of a rock bolt plays a very important role in the rock/resin/bolt load transfer mechanism. Very little work has so far been reported on the influence of the bolt surface geometry on the bolt/resin interface failure mechanism. This paper examines the behaviour of bolt surface roughness under constant normal stiffness condition in the laboratory. To study the shear behaviour of the bolt/resin interface a series of shear tests with an initial normal stress between 0.1 to 7.5 MPa has been conducted on the flattened bolt surface of two most popular bolt types currently being used in Australia. Bolts with deeper ribs offered better shear resistance at low initial normal stress conditions whereas bolts with shallow and closer ribs offered better shear resistance at high normal stress conditions. The maximum dilation occurred at a shear displacement of 60 per cent of the rib spacing irrespective of the bolt type and depth of the rib.

Jan 1, 2000

This paper describes the planning mechanism and implementation of a progressive rehabilitation programme at Hunter Valley Mine in the Upper Hunter Valley of New South Wales. Hunter Valley Mine is a large open cut coal mine which produces approximately 7.0 million tonnes of coal (run of mine) annually for export. This production level involves the movement of some 60 million tonnes of waste and coal each year.The rehabilitation programme at Hunter Valley Mine has been developed to provide a combination of pasture, based on improved pasture species and timber belts to enhance the visual characteristics of the rehabilitated landform, whilst creating amenity in the form of shade for livestock.The operational philosophy for the rehabilitation programme is that of progressive rehabilitation. The best time to undertake rehabilitation is now.' As a result, planning for the rehabilitation programme is continuous, so that all site works are completed in time for vegetation establishment during the critical periods each year.

Jan 1, 1992

By Eggins SM, Crawford AJ, Wallace ME, Falloon TJ

The Earth's Upper Mantle is dominantly peridotitic but in convergent margin regions, such as the S.W. Pacific, subduction of oceanic crust gives greater chemical and petrological diversity to upper mantle petrology and petrogenesis. Examination of currently active, Quaternary and Tertiary volcanism in the S.W. Pacific, particularly seeking information from ocean floor sampling to characterize the basement to island arcs and to investigate active spreading centres, consistently points to parental magmas of basaltic to picritic character. However, these parental magmas are chemically diverse and it is not possible to designate a characteristic 'island arc' or 'convergent margin' petrogenesis in the sense of a characteristic mantle source composition and a charactistic partial melting regime. In this respect, magma genesis at convergent margins contrasts with that at oceanic spreading centres. Our studies emphasize the importance of source peridotite ranging from 'fertile lherzolite' (i.e. compositions with 3-4% CaO, A12O3, 0.3-0.5% Na2O) to refractory harzburgite (

Jan 1, 1987

By R Barritt, P Scott, K Albano

Successful closure of tailings storage facilities (TSFs) is an environmental issue faced globally by metalliferous mines. During the initial feasibility and design phase of the mine life importance is placed on the physical stability of above ground TSFs, largely driven by legislative requirements, whilst closure planning is often a secondary consideration. However, as the landform is further developed and constructed attention must be paid to regularly revisit the original closure plan and update it to achieve the best (sustainable) possible outcome for both the environment and stakeholders. A mine in northern Queensland is in the process of developing a closure strategy at their TSF. Appropriate closure measures for the TSF are required to mitigate the impact of any seepage emanating from the TSF on the groundwater and surface water receptors. O’Kane Consultants Pty Ltd (OKC) have provided the mine assistance with the development of a TSF cover system design in order to appropriately manage tailings during operations and to prepare for the facilities’ closure. OKC has collected data since 2007 from cover system field trials located on the TSF. To enhance engineering judgement in the design of future cover systems, calibration of soil-plant-atmosphere numerical models to field data (referred as ‘field response modelling’) were completed. Calibrated model inputs can be used to provide insight into long-term cover system performance as well as a tool for design of the final landform.Following a site investigation, materials characterisation and numerical modelling program various cover system alternatives were developed. Two of the preferred cover system alternatives referred to as Test Plot #1 (TP#1) and Test Plot #2 (TP#2) (Figure 1), were constructed at the site and instrumented. Monitoring instrumentation comprised several nests of in situ volumetric water content and thermal conductivity sensors to measure changes in water content, temperature and matric suction within the cover system materials and underlying tailings waste. Run-off collection buckets and a fully-automated meteorological station were also installed. CITATION:Barritt, R, Albano, K and Scott, P, 2016. Findings and conclusions following ‘long-term’ cover system monitoring – refinement of the conceptual design for tailings storage facility closure, in Proceedings Life-of-Mine 2016 Conference , pp 85–88 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jun 28, 2016