Search Documents

By E. R. Gilbert, D. E. Munson

Creep of copper under 75 to 1.50 kg per sq cm stresses at temperatures near the melting point was found to he a complex reaction controlled by three mechanisms acting in parallel. In order of appearance with decreasing temperature, the auerage activation energies, Qc , are 168, 79, and 24 kcal per mole. Stress dependence of the minimum creep rate was found to he an exponential for the two high-Qc processes and a power law for the low-Qc, process. Transition of control occurs from one mechanism to another. The relative transition temperature depends upon the applied stress, and the range oiler which the transition occurs depends upon the difference in the activation energies of the mechanisms. The creep behavior at high temperature is explained by the climb of dislocations through thermally or mechanically formed jogs, CREEP in pure fcc metals at temperatures in excess of one half the absolute melting point is normally controlled by dislocation c1imb.1,2 A climb model which seems applicable, according to an extensive analysis of data,3 was derived by Weert-man.4 This model assumes jog-saturated dislocations and predicts an activation energy, Qc, nearly equal to that for self-diffusion, USd. Although the requirement of jog saturation is restrictive, agreement between theory and experiment seems adequate. Many other theoretical treatments, including an early model by Mott,5 include detailed consideration of jog formation as an initial requirement for climb. These models predict activation energies for creep which differ from those of self-diffusion. Seeger6,7 postulates an observed activation energy related to the stacking-fault energy. Thus, Usd <Qc<5Usd + Uj where Uj is the jog-formation energy. Seeger incorporated qualitatively the influence of the relative numbers of thermal and athermal jogs. Expanding this concept, Shoeck8 explicitly states a function based on formation mode and relative numbers of vacancies: e r ci exp {-uf/k T} exp {-Um/k T} [ 1 ] where Uf and Um are energies of vacancy formation and migration, respectively. The concentration of jogs, Cj, depends upon the manner of jog production. For intersection jogs, Cj is not sensitive E. R. GILBERT, Junior Member AIME, formerly with De- to temperature; for thermal jogs, Cj is proportional to exp {—Uj /k T}. Schoeck regards each mode as a distinct mechanism; therefore, the mechanisms may act together.299 The diversity predicted by theory, surprisingly, has not been substantiated by experimental results. A significant investigation must include the extremes in stacking-fault energy. Extensive creep studies of aluminum10 and nickel,11,12 high stacking-fault energy metals, have been made. Comparable studies on a low stacking-fault energy metal, such as copper, have not. It is the purpose of this paper to report the results of an investigation of the creep of copper under conditions which favor thermal jogs. EXPERIMENTAL Cylindrical compression creep specimens (0.240 in. in diameter by 0.400 in. long) were machined from cold-drawn rods of electrolytic tough-pitch copper containing 0.0007 Mg, 0.002 Fe, 0.001 Ni, 0.0005 Ag, Cd < 0.005, and Pb < 0.005 wt pct impurities. Undetected spectrographically was a nominal 0.04 wt pct 0, which occurs as a Cu2O constituent distributed discontinuously at grain boundaries. Vacuum annealing at 900°C for 15 min produced a stable 0.03-mm average grain diameter. Testing was carried out using apparatus similar to that described by sherby,13 modified by enclosing platens and a push rod in a vacuum cylinder. Normally this arrangement resulted in pressures less than 10 Only a slight surface tarnish, less than 0.0005 in. in thickness, occurred during the test. The applied stress, corrected for atmospheric pressure, was maintained within 2 pct of the desired true stress by the addition of lead shot at fixed strain increments. Creep strain was measured with dial gages as a relative displacement of the upper and lower platens; accuracy of measurement was 0.0001 in. Two creep-test methods were used, the differential or cyclic temperature14 and the isothermal, to obtain creep data at stress levels of 150, 100, and 75 kg per sq cm over the temperature range of 620° to 1032°C. Minimum creep rates were used from both test methods; this was considered proper because comparable temperature tests or cycling to the same temperature gave the same creep rate, within experimental error. The cold vacuum test chamber, with the unstressed specimen in place, was heated to temperature by placing a preheated furnace over the chamber. Temperature equilibrium was attained within 30 min. For the cyclic tests, the stress was removed during the 5 to 10 min necessary to effect the temperature change and re-

Jan 1, 1965

By R. M. Waterstrat

The phase VPt has been reported to have a crystal structure of the B19 (AuCd) type at low temperatures.&apos;&apos;&apos; A recent investigation3 has indicated that this phase forms by an ordering reaction from the disordered fcc Pt(V) solid solution which is stable at high temperatures. olander4 has shown that there exists a close structural relationship between the orthorhombic B19 structure and a fcc structure possessing the L1 , (CuAu) type of atomic ordering. One may derive the B19 structure by a shear-like displacement of the atoms in the (002) plane of the ordered fcc lattice along the (010) direction through a distance equal to one eighth of the unit cell dimension, see Fig. 1, followed by an orthorhombic distor; tion of the cube axes such that a = 2.693A. h = 4.413A. and c =4.767A (estimated uncertainty 0.005A). Filings of this phase were produced by grinding a VPt alloy having the B19 structure with a diamond dental grinding disc. When these filings were subjected to X-ray diffraction examination, a pattern of a severely cold-worked fcc structure was obtained. higher solution temperature used (1200 C) or to a much lower oxygen pressure than he reported, due to transfer through many bends and tubes in his complicated apparatus. An interesting observation was made when an oxygen addition was attempted in a cylindrical sample of columbium in the cold worked condition rather than in the annealed condition. The interior of the sample re-crystallized during the oxygen addition at 900°C. The periphery, however. (1 mm) did not recrystallize. A similar sample without oxygen recrystallized throughout the entire cross section. It appears that the re-crystallization is hindered by interstitial oxygen. Presumably, the interior recrystallized before appreciable oxygen could diffuse into the core. This work was supported by the United States Atomic Energy Commission. When the filings were annealed in a high vacuum furnace for 15 min at 110O0C, however. they returned to the B19 structure perhaps as a result of reordering. Subsequent less-severe cold-working of these filings by grinding in a hardened steel mortar and pestle at room temperature produced a transformation into a cold-worked L1, structure which was slightly tetragonal. Thus it appears that the degree of deformation may influence the final structure. Considerable line-broadening was observed in X-ray diffraction patterns obtained from the cold-worked filings and therefore no attempt was made to obtain accurate lattice parameters. Vacuum annealing treatments at 1100&apos;C intended

Jan 1, 1970

United Engineering Trustees, Inc C E Reistle, Jr (to Oct &apos;55), A B Kinzel, &apos;56, Andrew Fletcher, &apos;57, Philip Kraft (from Oct &apos;55 to &apos;59) The Engineering Foundation W M Peirce, &apos;56, A M Gaudin, &apos;58 Engineering Societies Library Board Frank T Sisco, &apos;58, C H Behre, Jr Engineering Societies Personnel Service Board of Directors E J Kennedy, Jr, E H Robie Advisory Committee, Milwaukee F T Agthe Special Survey Committee C M Cooley American Standards Association Mining Standards Board E R Borcherdt, &apos;55, Otto Herres, &apos;55, J K Richardson, &apos;56, E W Bullard, &apos;56, Alternate

Jan 1, 1955

By E. T. Turkdogan, J. H. Swisher

bi the fivst part of the paper results ave given on the rate of decarburization of Fe-C melts ln CO2-CO atmospheres at 1580°C. The rate -controlling step is believed to he that irvlloluing dissociation of curbotz dioxide on the suvfuce of the melt. 4 genevral reaction mechanistm is poslnlated jor gels-t11eta1 veactions oc-curit~g on the surface of iron coutcotamncited with chemi-sovbed osygesL. Oxygen the present work on decavbuvization of liquid iron and previous studies on the kinetics of nitrogen absorption and desorplion are discussed in terms of the postulated mechanism, ManY of the early studies of rate of decarburization of liquid steel were of an exploratory nature and laboratory exppriments carried out pertained to open-hearth or oxygen steelmaking processes. References to previous work on this subject may be found in a literature survey made by Ward. Using more sophisticated experimental techniques, several investigators have recently studied the kinetics of decarburization of molten Fe-C alloys in oxygen-bearing gases. For example, Baker et al2.&apos; reported their findings on the rate of decarburization of liquid iron, levitated by an electromagnetic field, in carbon dioxide-carbon monoxide-helium atmospheres. In these levitation experiments the samples used were small in size, e.g., -0.6-cm-diam spheres weighing -0.7 g, and the rates were measured for decarburization from about 5 to 1 pct C at 1660°C. The rates obtained under their experimental conditions were considered to be controlled primarily by gaseous diffusion through the boundary layer at the surface of the levitated melt. Parlee and coworkers3 measured the rate of absorption of carbon monoxide in liquid iron. The rates were found to follow first-order reaction kinetics, yielding a reaction velocity or a mass transfer coefficient in the range 0.2 to 0.4 cm per min. The coefficient was found to decrease with increasing carbon content of the melt. These investigators attributed the observed rates to the transfer of carbon or oxygen through the diffusion boundary layer adjacent to the surface of the melt. In the work to be reported in this paper, an attempt has been made to study the kinetics of gas-metal surface reactions involved in the decarburization of liquid iron. EXPERIMENTAL The experiments consisted of melting 80-g samples from an Fe-1 pct C master alloy in an induction furnace and decarburizing in controlled CO2-CO mixtures at 1 atm pressure and 1580°C. The master alloy was prepared by adding graphite to electrolytic "Plastiron" melted in racuo. None of the impurities in the master alloy exceeded 0.005 pct. The reacting gases were dried by passage through columns of anhydrone; in addition, CO2 impurity in carbon monoxide was removed by passage through a column of ascarite. A schematic diagram of the apparatus is shown in Fig. 1. A 1.25-in.-diam recrys-tallized alumina crucible containing the sample was placed inside a 3-in.-diam quartz reaction tube, all of which was surrounded by an induction coil. A 450-kcps induction generator was used as the power source. Water-cooled brass flanges, which contained the gas inlet, gas exit, and sight port, were sealed to the top of the reaction tube with epoxy resin. The reacting gases were metered with capillary flowmeters and passed through a platinum wire-wound alumina preheating tube, 0.25 in. ID and 11 in. long. The gases were preheated to about 1300°C. A disappearing-filament optical pyrometer was used to measure the melt temperature. The pyrometer was initially calibrated against a Pt-6 pct Rh/Pt-30 pct Rh thermocouple. The temperature was controlled to within +10°C by manually adjusting the power input to the induction coil. In a typical experiment, an 80-g sample of the master alloy was melted in a CO2-CO atmosphere having pcO2/pco = 0.02 and flowing at 1 liter per min. A negligible amount of carbon was lost and no significant reduction of alumina from the crucible occurred during melting, e.g., 0.005 pct Al in the metal. After reaching the experimental temperature of 1580°C, the gas composition was changed to that desired for a particular series of decarburization experiments. The duration of the transient period for obtaining the desired gas composition at the surface of the melt was about 20 sec . The flow rate of the reacting gas was maintained at 1 liter per min. After a predetermined reaction time, the power to the furnace was turned off. During freezing, which took about 10 sec, the amount of gas evolution was not sufficient to result in a significant loss of carbon. The samples were analyzed for carbon by combustion and in a few cases they were analyzed for oxygen by the vacuum-fusion method. RESULTS A marked increase in the rate of decarburization of iron with increasing pcO2/pco ratio in the gas stream is demonstrated by the experimental results given in Figs. 2 and 3 for pco2/pco ratios from 0.033 to 4.0. In one series of experiments, denoted by filled triangles in Fig. 2, the reacting gas was diluted with argon (48 vol pct) resulting in a slower rate of decarburization. Samples from two series of experiments with pco2/pco = 0.033 and pco2/pco = 0.10 (with argon dilufion) were analyzed for oxygen. In these Samples the oxygen content increased with reaction time

Jan 1, 1968

Ahrenholz, Herman William, Jr., Student, Lehigh Univ Bethlehem, Pa. &apos;35 Allen, Carl A., Student, Colorado School of Mines Golden, Colo. &apos;35 Allen, Paul W., Student, Mass. Inst. of Tech Cambridge, Mass. &apos;35 Allen, R. M., Jr., Student, Virginia Polytechnic Inst., "G" Co Blacasburg, Va. &apos;35 Amberger, K. H., Student, Michigan College of Min. & Tech Houghton, Mich. &apos;35 Andersen, Burton Lee, Student, School of Mines, Univ. of Washington Seattle, Wash. &apos;35 Anderson, Joseph S., Student, Univ. of Texas El Paso, Tex. &apos;35 Anderson, R. C., Student, Univ. of Washington Seattle, Wash. &apos;35 Ansel, Gerhard 627 Clyde St., Pittsburgh, Pa. &apos;34 Anutta, Frederick P., Student, Michigan College of Min. & Tech Houghton, Mich. &apos;35 Apsouri, Constantin N., Graduate Student, Univ. of Arizona Tucson, Ariz. &apos;35 Arakelian, Haig Mark, Student, Mass. Inst. of Tech Cambridge, Mass. &apos;34 Archer, George K 1420 Court Pl., Denver, Colo. &apos;34 Argall, George O., Jr., K. E. House Golden, Colo. &apos;35 Argiielles, Alfredo, Student, Univ. of Texas El Paso, Tex. &apos;35 Atwater, Ralph, Student, South Dakota School of Mines Rapid City, S. D. &apos;35 Austin, Robert B., Miner, Page Mine, Federal Min. & Smelt. CoSpokane, Wash. &apos;34

Jan 1, 1934

By K. R. Evans

The deformation mechanisms occurring in polycrys-talline, commercially pure titanium and a Ti-8 pct A1 alloy have been investigated and compared to earlier results by Levine on high-purity titanium single crystals and by Conrad on commercially pure titanium. In accord with Levine, two consecutive deformation mechanisms are observed to exist below 500°K with the transition temperature between mechanisms, Tc, strongly dependent upon interstitial composition. T, is found to be 210°. 375° -430°, and 450°K for alloys A large number of investigations have been conducted to determine the rate-controlling mechanisms of plastic deformation occurring in fcc and bcc metals. Very few investigations of a similar nature have been conducted for hexagonal metals. In fact, until very recently, magnesium is the only hexagonal metal which has been systematically investigated for determination of the rate-controlling deformation mechanisms.1"3 From these investigations, it was concluded that basal slip below 420°K occurs by the intersection of forest dislocations,1&apos;3 while for prismatic slip the Peierls mechanism is rate-controlling at low temperatures with interstitial compositions of 0.024, 0.42, 0.61, and 1.13 at. pct expressed in terns of oxygen equivalents. The low-temperature mechanism is found to be an impurity obstacle mechanism in contrast to Levine&apos;s earlier conclusion of the Peierls barrier. Measurement of the activation parameters for deformation and estimation of the force-distance profile of the obstacles show their retarding force to be effective over longer distances from the obstacle as the interstitial composition increases. and thermally activated cross slip at higher temperatures. 2 The potential technological importance of titanium alloys has prompted recent studies of the deformation and fracture characteristics of titanium and its alloys. 4-8 Levine&apos; systematically investigated the low-temperature deformation behavior of high purity titanium single crystals oriented for either basal or prismatic slip. It was concluded that the Peierls mechanism was rate-controlling at temperatures below 210°K, while above this temperature an undefined mechanism was rate-controlling. Conrad 7,8 concluded from an analysis of the composition dependence of the critical shear stress at 0°K and measurement of the activation parameters that the low-temperature deformation of titanium is controlled by an impurity

Jan 1, 1969

By J. W. Cloud

years ago upon the effect of having the rails always rolled in the same direction, and also of having them rolled backwards and forwards, and showed that under the latter course there were of necesshy weak spots somewhere near the centre of the rail, yet in all this discussion the methods of rolling have been passed by almost in silence. Mr.. Sandberg in his paper mentions the idea of using a regietering dynamometer attached to the punching machines, and of det.erminit~g the quality of the metal by the resistance which is shown. I think the&apos; first idea of this kind was published by Professor Langley, then of Pittsburgh, who, while making some investigations for Mesrs. Miller, Metcalf and Parkin, announceti as tile result of a series of dynamometric experiments that abrasive resistance was the term which should be wed in regard to steels of different wearing qualities. I have had extremely delicate dynamometers attached to the instruments of precision with which I am making the iuvestigation on the fatigue of metals, and hope soon to communicate the results of the iovegtigation- made with them to the Institute. I wish again to call attention to the fact that we are wing the words " hardener " and " hardness " without any real idea of the meaning of these words. When we say hard and soft, as we have hen constantly doing during this discussion, is it quite sure that every one has exactly the same meaning in his mind ? Certainly, when hard is used in distinction from soft*, we mean not the capacity of wear, but the capacity of resistance to peuetration, to fracture, or some other resistance, and do not always meau the capacity of resistance to abrasion or crushing, which the discussion would sometimes seem to imply were the only qualitiw requisite to constitute a god rail. J. W. Cloud, Altoona, Pa. : I would call the attention of the Institute to the title of Dr. Dudley&apos;s interesting and valuable paper, —" The Wearing Capacity of Steel Rails in relation to their Chemical Composition and Physical Properties." Here are two separate and distinct questions: lst, The wearing capacity of steel rails in relation to their chemical content; and 2d, the wearing capacity of steel rails in relation to their physical properties. The discussion has been almost exclusively confined to the former question, on which there may be many differences of opinion in matters of detail without greatig affecting the result. The latter

Jan 1, 1881

By P. R. Smith, R. A. Walters

Borates have been mined in the desert areas of California and Nevada for more than 100 years. To about 1890, playa surface mining provided the chief sources of boron minerals. Underground mining of colemanite and later of borax and kernite was predominate until about twenty years ago. Open pit mining of the large deposits of borax and kernite near Boron, California has been most significant for the past twenty years. Mining of colemanite in the Ryan, California area, near Death Valley, began in 1907. Following the discovery of the large deposits in the Boron area (about 1957), mining in the Death Valley area became nearly nonexistent. Only small tonnages were mined for special uses. Little mining was done in the Boraxo area near Ryan. The first claim was made in about 1915. In 1960 the area became the property of the Kern County Land Company, which was acquired by Tenneco Oil Company in 1967. In 1976 the various boiate properties and claims in this region were acquired by American Borate Corporation. The open pit mine is now approximately 122 m (400 ft) deep, 910 m (3000 ft) long and 305 m (1000 ft wide). The borates in the Boraxo pit consist primarily of three minerals. These are about 50% colemanite (CB6011 5H20), about 40% probertite (NaCaB50g 5H20), and 10% ulexite (NaCaBgOg 5H20). The colemanite, along with boric acid and high-grade colemanite ore from Turkey provide the only sodium-free borates for production of textile grade fiberglas. When heated to its decomposition temperature, colemanite decrepitates to a fine powder, which is the basis for the concentration process. The gangue minerals in this deposit are primarily calcite and clays, including bentonite. The ore body has a very low arsenic content, which is a desirable feature. Test work had been done with samples prior to the results discussed herein. This paper will discuss results of test work which were the basis for erection of a plant, and the subsequent plant operations. Laboratory Calcination and Air Tabling Tests Laboratory calcination tests showed that substantial upgrading of the borate could be accomplished by calcining followed by screening of the calcined material. Removal of the + 28 mesh calcine resulted in borate losses of less than 10% with a rejection of 40 weight % or more of the calcine. The minus 65 mesh calcine generally met the requirement of containing 48%, or more, B203. The minus 28 plus 65 mesh material contained an intermediate quantity of borate and would require additional treatment. Testing demonstrated that ore would not have to be reduced to a size finer than 19 mm (3/4 in.) prior to calcination. A temperature range from 400 to 455OC (750 to 850°F) was apparently satisfactory. Calcination at a temperature of 48Z°C (900°F), or higher, was unsatisfactory due to fusion. All laboratory calcination tests were static tests conducted by placing small covered charges in a laboratory furnace for 40 min. In all tests vapor issues from the furnace for 5 to 7 min. Following this period the ore could be heard "popping," due to decrepitation of the colemanite. The reaction generally continued for approximately one-half hour. Various size fractions of the calcination products from laboratory tests were subjected to laboratory air tabling tests, usually after removing the plus 28 mesh material. Laboratory air tabling tests were conducted employing a Whippet V-80 model air table manufactured by Sutton, Steele and Steele Co. now known as Tripple S Dynamics. Variables include both end and side-tilt, speed of vibration, and quantity of air rising through the deck. In addition to the variables in the machine itself, the feed rate is also a rather critical variable. Testing demonstrated that all - 28 mesh size fractions of the calcine could be successfully concentrated to 48% F2O3 or greater. For the finer material recoveries into the concentrate were between 85 and 90% of the borate. With the coarser material a substantial amount of middling was produced which required cleaner tabling. Laboratory calcination and air tabling tests indicated a process whereby the borate could be concentrated to about 50% B203 with borate recoveries approaching 90%. Moreover, the iron content of the concentrate was well below the required specification of 0.3% Fe2O3. Pilot Plant Calcination Following the laboratory test work described above, pilot plant testing was conducted to prove the process, provide data for engineering studies, and provide product for a prospective purchaser. The kiln used was 0.9 m-diam (3 ft) by 9.0 m (30 ft) long and had a belly section 1.2 m-diam (4 ft) by 2.74 m (9 ft) long near the discharge end. The kiln was operated at a speed of 0.7 rpm. Gas was fired into the kiln at an average rate of 27.1 m3/hr (958.4 cu ft per hr). The air to gas ratio used was 10:1. The ore was fed to the kiln countercurrent to the flame and discharged through a hopper into a screw conveyor which discharged to a 1.2 m (48 in.) Sweco separator. The separator had 28, 65, and 150 mesh screen cloths, with the plus 28 mesh fraction being discarded. The minus 28 mesh fractions were later subjected to air tabling. The exit gases, containing some calcine dust, were swept through two cyclones to recover the dust. The gases then were scrubbed in a Ducon scrubber; very little dust reported past the first cyclone. The dust from the first cyclone was also saved in drums. In addition to the gas rate, the flue gas velocity, after

Jan 1, 1981

Furnace Builder. Engineer with extensive experience in furnace building. Position with well-established firm, branching into new fields. Location Ohio. 11-1343. Erecting and Operating Engineer to take charge of erection of gas-producer equipment and to teach customers how to operate such equipment. Location Ohio. Salary $250 per month. R-1339. Assistant Professor in Mining School, for instruction work; must have had experience in ore dressing and metallurgy. Location Missouri. Salary $1500-$2100 per school year (8 mo.). R-1332. Consulting Engineer, familiar with construction of artesian wells to act in a consulting capacity. Location New York City. R-1324. Mining Engineer and Investigator to do non-metallic mineral investigations in both field and office for United States Government. Position will last at least a year, and may become permanent. Location Washington, D. C. Salary $1800-$2700 depending on qualifications of appointee. R.-1317. Crushing Plant Superintendent, cement mill and construction experience essential. Prefer man who has had limestone crushing experience. Location New York. R-1314. Assistant Professor of Coal Mining, must be a graduate of mining engineering and have had some coal mining experience. Location Philadelphia.. Salary $2200 for school year of 10 months. R-1312.

Jan 9, 1919

By Oliver Smalley

EXCEPT for the work of Guillet, who conducted a systematic investigation on the zinc-replacing value of nickel in brass, and extended his investigation with a view to developing commercial high zinc content nickel brasses, the author does not know of any systematic research on the subject. The most promising commercial alloys and their physical properties obtained by Guillet are given below: Maximum Elonga- Reduction Copper Zinc Nickel Stress, tion, of Area, Brinell Tons Per Per Cent. Per Cent. Sq. In. 55.0 41.0 5.0 24.4 46.5 94 Sand cast. 22.6 27.0 90 Chill cast. 56.7 39.74 3.35 30.0 43.0 51.7 97 Casting annealed 2 hr. at 750° C. 33.9 33.0 50.7 144 Cold-drawn bar. 55.15 42.3 2.24 29.8 33.0 116 Casting annealed 2 hr. at 750° C. 32.3 29.0 151 Cold-drawn bar. These test results scarcely justify the use of such quantities of so expensive a metal, and could have been obtained from ordinary commercial brass. For purposes of comparison, the physical properties of ordinary brasses, ranging from 70 per cent. to 50.1 per cent. Cu in both the cast and normalized1 conditions are included in Table 1. These incidentally furnish a useful standard of the properties of castings and of rolled, extruded and forged brass when correctly annealed. A close study of some of the well-known special brasses containing nickel reveals a series of alloys which bewilder by their complexity, and one can only hazard a guess at the function and commercial value of each of the many elements used.

Jan 10, 1925

By T. Kunitake, H. W. Paxton

The self-diffusion coefficient of chromium in various alloys in the iron-chromium system has been measured. A variation in Dofrom 10-4 for pure chromium to a maximum of 102 near 60 pct Cr appears with a range of activation energy from about 50 to 80 kcal per mol. The general pattern of behavior observed is not consistent with present theories of diffusion by a vacancy mechanism. Suggestions are made for further clarifying experiments. RECENT work on the self-diffusion of chromium,&apos; ?-uranium2-4 and ß-zirconium,23, 26 has indicated that these elements have very low Do (10-3 to 10-4) compared to that conventionally expected for vacancy diffusion. Pound et al.5 have suggested that this may be due to ring diffusion being operative, and have proposed a model which gives Do of the correct order of magnitude. The essential difference between this model and Zener&apos;s earlier model6 is that whereas Zener assumes tight coupling between atoms in a ring to establish a vibrational frequency, Pound&apos;s model allows the atoms to vibrate essen- tially each in their own normal modes. The probability of each atom moving in the correct direction to cause a ring of n atoms to rotate by 2p/n must then be calculated as a "synchronal entropy" which may be -20 e.u. for a 4 atom ring. In iron, the latest determinations of self-diffusion yield Do in the range 18 to 522.7-9 The most accurate is probably that of Borg and Birchenall8 which is 118 ± 3. This value is not inconsistent with that expected for a vacancy mechanism. Since iron and chromium are very closely similar in size, are both transition metals, and their solution is thermodynamically ideal at temperatures of interest in diffusion, it appeared that a determination of self-diffusion coefficients, Do and Q as a function of composition would be of substantial interest to diffusion theory. The following measurements were made with this purpose in mind.

Jan 1, 1961

By O. W. Simmons, L. W. Eastwood, C. M. Craighead

The results of a preliminary study of 113 ternary titanium-base alloys are described. The compositions investigated were as follows: 1. Ternary titanium-carbon alloys containing copper, silicon, vanadium, chromium, manganese, iron, or cobalt. 2. Ternary titanium-nitrogen alloys containing chromium. 3. Ternary titanium-chromium alloys containing additions of vanadium, molybdenum, tungsten, cobalt, or nickel. 4. Ternary titanium-manganese alloys containing additions of silicon, chromium, tungsten, or iron. Tensile properties, minimum bend radii, hardnesses, response to heat treatment and aging treatment, and phase relationships for these alloys were determined. THIS is the second in a series of papers describing some of the results of the exploratory work on titanium alloys being conducted at Battelle Memorial Institute for the Wright-Patterson Air Force Base. The work with the binary alloy systems has been described in a previous publication.&apos; This paper describes ternary titanium-base alloys as follows: 1. Ternary titanium-carbon alloys containing copper, silicon, vanadium, chromium, manganese, iron, or cobalt. 2. Ternary titanium-nitrogen alloys containing chromium. 3. Ternary titanium-chromium alloys containing additions of vanadium, molybdenum, tungsten, cobalt, or nickel. 4. Ternary titanium-manganese alloys containing additions of silicon, chromium, tungsten, or iron. As the preparation and fabrication of the 0.5-Ib experimental titanium alloy ingots to 14-ga sheet, as well as the methods of testing used in this work, have been described in the first paper of this series, Titanium Binary Alloys, no further discussion of these techniques will be given. Ternary Alloys Containing Carbon The following alloys of titanium, containing carbon and one other metal, were investigated: 1. 0.25 pct carbon; 1, 2.5, and 5 pct copper. 2. 0.25 pct carbon; 1, 2, and 3 pct silicon. 3. 0.25 pct carbon; 1, 2.5, and 5 pct vanadium. 4. 0.25 pct carbon; 2.5, 3.5, 5, 10, and 15 pct chromium. 5. 0.5 pct carbon; 2.5, 3.5, and 5 pct chromium. 6. 0.25 pct carbon; 1, 1.75, 2.5, 3.5, 5, 7.5, and 10 pct manganese. 7. 0.5 pct carbon; 1.75, 2.5, 3.5, 5, 7.5, and 10 pct manganese. 8. 0.25 pct carbon; 0.25, 0.5, 1, and 2 pct iron. 9. 0.25 pct carbon; 1, 2, and 3 pct cobalt.

Jan 1, 1951

By George W. Sheary

Situated 45 miles west of Philadelphia and 50 miles southwest of Bethlehem Steel Company&apos;s Bethlehem plant, the integrated Grace mine facilities produce 4000 tpd of high-quality iron ore pellets. Startup of the Grace mill was in November 1958, and iron concentrates were shipped until March 1960, when the pellet plant went into operation. The underground mine, when fully developed, will hoist about 9000 tpd, including development rock. The crude ore, which has an iron content of approximately 42%, is magnetically cobbed and crushed in closed circuit with 3/4-in. slotted vibrating screens. The ore is washed and screened in the mill and the plus 1/4 in. screen product is again cobbed prior to feeding to the rod mills. Grinding is done in rod mills, and in ball mills that are in closed circuit with 30 in, cyclones, to 1% on 100 mesh and 65% minus 325 mesh. The ground ore is magnetically concentrated by three-drum permanent type finisher magnets to 67% Fe. The magnetite concentrate is pumped from the mill to a 50 ft thickener in the pellet plant. The thickened magnetite concentrate is relayed to the filters through a two-stage pump arrangement. The filter cake is fed by belt from filter concentrate bins to mixer-muller belts where it is intimately mixed with bentonite and a slight amount of water for moisture control. The fluffed concentrate then drops into balling cones. The green pellets from the balling cones are fed in a prescribed feed pattern to shaft furnaces through the use of shuttle car mechanisms. The green pellets are dried, heated to 2500°F and cooled to 1200°F as they descend through the furnace and into pellet coolers where the pellets are further reduced in temperature to 250°F. Heat is recovered in the cooling process through the use of air-to-air heat exchangers. The cooled pellets discharge on a rubber conveyor belt and are transferred to 6000-ton pellet railroad loading bin. The final pellet product consists of 90% plus 1/4 in. material (after tumble testing1) and contains 66% Fe plus 3% silica.

Jan 5, 1962

By Edgar Bain

SUMMARY THE results of an enquiry into the structural nature of some 70 iron alloys containing both nickel and chromium over a considerable range of concentration &apos;are briefly described in this paper. This study is a part of a comprehensive program of investigation into alloys involving chromium in progress at the Union Carbide and Carbon Research Laboratories. All the compositions studied contained carbon in amount comparable to commercial alloys.

Jan 3, 1927

By E. S. Machlin

The wzodel of Blandin and Diplunt;, generalized to include a phase factor, is applied to the carbon-carbon interaction in iron. Darken&apos;s "energetic" model is generalized to include not only first neighbor interactions but further neighbor interactions as well. On the bases of these generalized models relations are derived for the activity of carbon in both austenite and ferrite in terms of the carbon-carbon Pair interaction energies. A single function then yields the pair interaction energies consistent with the experimental activities of carbon in both ferrite and austenite. Thus, a simple explanation is given for the observation that the nearest-neighbor interaction between carbon is repulsive in austenite and attractive in ferrite. Certain consequences of this approach are explored. OnE object of the present paper is to attempt to take into account the consequences of electrostatic contributions to the carbon-carbon pair interaction energy for carbon as a solute in iron. Friedel&apos; has shown that oscillations in electrostatic potential are to be expected about a solute atom in a metallic solution. Blandin and 6lant6&apos; have shown that such oscillations yield an interaction energy between pairs of solute atoms that obeys the relation: W{ = A cos(2ftFri + 4>)/(kFri)3 [l] where kF = Fermi wave vector, ri = distance between solute atoms comprising the pair7 <p = phase factor dependent only on electronic nature of solute and solvent, A = coefficient dependent only on electronic nature of solute and solvent. Machlin3 found that Eq. [I] accurately described the pair interaction energy derived from short-range order measurements based on field ion microscope observations of dilute alloys of platinum. He also found that the value of the phase factor $ derived from residual resistivity measurements agreed well with that obtained from the analysis of the short-range order data. Harrison and paskin4 were able to predict the long-range ordering energy of 0 brass using Relation [I] and residual resistivity values to predict the value of the phase factor $. Machlin5 has repeated their analysis and applied it to the prediction of the long-range ordering energy in AgZn and AgCd with excellent agreement between prediction and experiment. Both A and $ are independent of the crystal structure. The Fermi wave vector depends uniquely upon the conduction electron concentration per unit volume in the spherical approximation of the Fermi surface. Thus, Eq. [I] is expected to apply to both fer- rite and austenite with only one set of values of A and $. Mossbauer studies6 yield the result that iron has one 4s electron. We shall make an assumption found to hold previously for platinum3&apos;7 and nikel, which is that only the s electrons are involved in shielding the perturbing potential of carbon. With this assumption, kF = 1.35 A-l. Although A and $ may be obtained from certain mdels&apos;&apos;&apos; we shall take A and $ to be empirical constants in the spirit of Kohn and osko.&apos; Thus, Eq. [I] involves two adjustible parameters. Consequently, two independent relations in A and $I are required in order to evaluate them for carbon as a solute in iron. We may use a recent analysis of Aaronson, Domain, and poundg who showed that Darken&apos;s energetic model,1° as well as others, can be used to describe the activity-temperature data for carbon in iron in both the aus-tenitic and ferritic phases. Darken&apos;s model takes into account only first neighbor pair interactions. For our needs, all neighbor pairs need to be taken into account. It is convenient to generalize Darken&apos;s model. The result for the partition function for austenite is: over the temperature range 800" to 1200°C and where the uncertainty corresponds to one standard deviation. Eq. [4] effectively yields only one relation. Another relation is required to obtain unique values for A and $. One property of Eq. [4] is that it is independent of crystal structure. Hence, data for a iron can be used to obtain another relation. To arrive at this relation we must generalize Eqs. [2] and [3] so that they may be applied to the bcc a iron. The result is that:

Jan 1, 1969

By B. L. Averbach, M. F. Comerford, M. B. Rough

The volume fraction of ß phase was determined in a Ti-6Al-4V alloy by measurements of integrated diffraction intensities. The (0002), and (100)ß diffraction lines were chosen because this combination minimizes the errors resulting from preferred orientation. The difficulties arising from fluorescence radiation were eliminated by use of a diffracted beam monochromator. A specimen quenched from 1475OF (800°C) contained approximately 5 pct ß, but in specimens quenched from higher temperatures no ß was found. The ß phase formed during aging, and in specimens solution treated at 1570oF (855oC) approximately 10 pct ß was present after aging at 1000°F (540°C) for 24 hr. This ß appears to form by decomposition of martensitic a&apos;. ThE kinetics of the reactions which occur during the heat treatment of titanium alloys are complex &apos; and not completely understood. It has been proposed that hardening occurs in some alloys&apos; on aging by the precipitation of a transition phase w followed by the formation of the stable a and ß phases. It has been proposed for other alloys2 that the a&apos; marten-site decomposes by precipitating finely dispersed a particles. Most investigations have been hampered by the difficulties of determining quantitatively the amounts of the various phases present. This paper is concerned with the measurement of the amount of ß phase by an X-ray method, similar to one developed for the determination of retained austenite. The principal new feature was the use of a mono-chromator in the diffracted beam in order to reduce the fluorescence arising from the sample. EXPERIMENTAL PROCEDURE The experiments were carried out on an alloy of nominal composition Ti-6Al-4V (actual weight percentages: 6.2 Al, 4.1 V, 0.02 Mn, 0.17 Fe, 0.005 H, 0.03 C, and 0.02 N). The material was received as 5/8-in.-diam centerless ground rods in the annealed condition. The heat treatments were carried out in a vacuum of approximately 0.03µHg. The X-ray intensity measurements were made on 3/8-in. thick discs. The surface was prepared by grinding off about 0.060 in. and electropolishing in a solution af 60 ml (70 to 72 pct) perchloric acid in 1000 ml glacial acetic acid with a current density of 0.5 amp per sq cm.q The X-ray determination is based on the proportionality of the diffracted intensity of each line to the volume fraction of the corresponding phase. In calculating the intensities for a powder sample it is assumed that a large number of grains con- tributes to the diffracted intensity and that the grains are oriented at random. The presence of preferred orientation introduces serious errors in the relative intensities. The material used in this investigation exhibited a strong preferred orientation, which could not be removed by heat treatment. Other investigators have also found that preferred orientation may be retained after phase transformations. Glen and pugh5 performed a detailed analysis of the randomness expected after several allotropic transformations, but stated that this is not observed. Burgers,6 and Burgers and Ploos van Amstel,7 found that, in zirconium, the original orientation is retained after two phase transformations. Newkirk and Geisler8 observed similar behavior in titanium. On the basis of this evidence, it appears that, in the absence of plastic deformation, textures present in annealed titanium alloys are retained. Heating an a-ß alloy to the all-ß region and subsequent cooling to room temperature do not make the orientation of the mar-tensite different from that of the original a phase. In the present investigation it was possible to take advantage of the crystallographic relationships involved in the martensitic transformation to minimize the errors associated with preferred orientation. The relative orientation for titaniu-m marten-site9 takes the form (0001), 11 (110)ß; [1120], 11 [lll]ß. The same relationship has been proposed for zirconium&apos; and certain titanium-base alloys.10-12 Additional sets of approximately parallel planes have been determined for titanium-nickel alloys." The influence of preferred orientation can be minimized by comparing intensities from parallel planes in the two related phases. If it is assumed that each family of planes in a given phase is equally well populated, the effect of preferred orientation can be eliminated by using the normal multiplicity for the family of planes since each set of parallel planes is equally preferred for any orientation of the sample relative to the X-ray beam. The most suitable combination of reflections in the Ti-6A1-4V alloy appeared to be (0002), and (110)ß It must be recognized that the ß formed during aging of the Ti-6A1-4V alloy is a precipitate rather

Jan 1, 1960

By R. K. Iyengar, G. C. Duderstadt

An investigation was carried out to determine the effect of Ca-Si additions on the dissolved oxygen content of liquid steel. An apparent equilibrium was reached after holding the melt for some time when the total oxygen content of the melt was identical with the dissolved oxygen. Results of the investigation show that for deoxidation with silicon and manganese the apparent equilibrium is reached after 8 to 12 min and the oxygen content of the melt is in good agreement with values reported in the literature for similar steel compositions. Ca-Si additions decrease the dissolved oxygen content appreciably below that obtained with Si-Mn deoxidation. It is postulated that some calcium dissolved in liquid steel at the time of its vaporization combines with dissolved oxygen to form CaO which then fluxes the manganese silicate, thereby lowering the activity of the deoxidation products. Slow flotation of calcium silicate inclusions is attributed to their slower growth rate. An addition of aluminum (to yield <0.005 pct Alsol) prior to introduction of Ca-Si improves the kinetics of removal of resulting deoxidation products. WITH the introduction of continuous casting of billets and blooms, application of calcium-containing alloys for deoxidation purposes has gained new interest. More so than in conventional ingot casting, the degree of control of the dissolved and total oxygen contents in steel for continuous casting can determine the success or failure of the operation because these affect both surface (pinholes) and internal quality of the billets. Of the available deoxidizers, only silicon has so far found wide application. However, in the typical range of application (0.20/0.30 pct Si), it is too weak a deoxidizer to suppress pinhole frequency to the level desirable for all but the least demanding appli-cations (approximately 10/50 pinholes per sq ft, de-pending on degree of subsequent reduction). On the other hand, Vincent&apos; has shown that it requires ap-proximately 0.007/0.008 pct A1 soluble in the steel to suppress pinhole formation to <10 pinholes per sq ft. In view of the difficulty of consistently maintaining this aluminum level and the associated problem of tundish nozzle constriction2 when aluminum is added to the ladle, steelmakers have searched for other de-oxidation alloys to circumvent the problem. Calcium-containing alloys offer such a possibility. When employed as a partial substitute for silicon, CaSi (30 pct Ca/60 pct Si) additions are reported to yield adequate pinhole contro1.3 Its use simultaneously preserves the "fluidity" of the steel and ensures good castability.4 Oxygen contents as low as 0.007 to 0.014 pct have been obtained with CaSi additions varying between 3 to 8 lb per ton.5-7 Due to the high degree of vaporization of calcium at the temperature of molten steel and the different methods used to introduce it into the liquid, the reported results show considerable scatter and lack of consistency. According to several investiga- deoxidation tors, the flotation characteristics of CaSi products are not as favorable as those found for alumi-num but are similar to those established for silicates with low alumina content.678 Thus, cleanliness ratings were improved when CaSi was replaced by a com-bination of Si + A1 followed by CaMnSi additions.5,9 In view of the lack of a comprehensive description of the deoxidation potential of CaSi alloys, a study was undertaken of the effect of CaSi additions on oxygen content in comparison to Si + Mn and Si + Mn + Al. The alloy chosen for this study contained 63 pct Si, 32 pct Ca, <3 pct Al, and 2.5 pct Fe. EXPERIMENTAL PROCEDURE The experiments were divided in three groups as shown in Table I. In each group, the CaSi addition was increased successively while maintaining the melt composition constant. The experiments in the third group were designed to determine the effect of prede-oxidation with small amounts of aluminum. Ingot iron, containing 0.02 to 0.03 pct C and 0.03 to 0.05 pct Mn, was melted in a 100-lb magnesia crucible. Pig iron was added to the melt under air in an induction furnace to attain the desired carbon content of 0.05 to 0.15 pct and thereby control the initial oxygen content of the melt between 0.04 and 0.015 pct. After removal of the slag, the furnace was sealed and argon was introduced through an opening in the graphite cover, Fig. 1. When the desired temperature was reached, electrolytic manganese was added to the melt and pin samples were taken (7 mm silica tubing) to establish initial oxygen content. To obtain maximum efficiency, CaSi and metallic silicon were introduced in a sealed steel pipe into the bath. This procedure assured minimum loss of calcium through vaporization as the deoxidants were always released at the bottom of the melt. Samples were taken at regular intervals and quenched in water. Temperature of the bath was measured with a Pt/Pt-10 pct Rh thermocouple. Portions of the pin sample were used for oxygen analysis; five determinations per sample were made to obtain average oxygen content. Oxygen analyses were made by the inert carrier gas fusion method with frequent cross checks with the vacuum fusion method.

Jan 1, 1970

By James R. Holden, Frederick E. Wang

Through both single-crystal and powder X-ray diffraction methods, ten A6B23-type compounds have been confirmed to exist between lanthanides (A) (plus scandium and yttrium) and manganese (B); A = Y, Nd, Sm, Gd, Tb, Dy, Ho, Er, Tm, and Lu. The formation of a compound of this type is shown to he extremely atomic size-sensitive; hence it can be classified as a "size-factorH compound. The "enveloping effect", a geometrical consideration observed in its crystal structure, is proposed as the reason for the A6B23-type compound being size-sensitive. The approximate ideal geometrical ratio of the radii R/r is 1.31 while experimentally A6B23-type compounds have a radius ratio lying within the range 1.2 to 1.4. FLORIO t al.&apos; characterized the structure of Th6MnZ3 as fcc, space group Fm3m, with 116 atoms in the unit cell. Since then, a number of isotypic binary compounds, and recently Gd n,,&apos; have been confirmed to exist. The fact that strontium and barium form A6Bz3-type compounds with magnesium strongly suggested the possible existence of Ba6Liz3. However, investigation3 showed the compound Ba6LiZ3 to be absent. Since both strontium and barium are group 11-a elements and are therefore "open metals",6 the nonexistence of Ba6LiZ3 can hardly be explained satisfactorily by valence-electron considerations. On the other hand, the consistent atomic-radius ratio, (R/r),* observed for the known A6Bz3-type compounds,3 strongly suggests that the formation of compounds of this type is atomic size-sensitive. Therefore, one is tempted to explain the nonexistence of Ba6LiZ3 entirely on the basis of the atomic-size difference between strontium and barium. However, this approach is not entirely without objection. Atoms are not rigid spheres and are known to vary in size within certain limits.7 Since the atomic-radius difference between strontium and barium (0.07 to 0.09A) is within these limits, it is reasonable to assume that the size difference would have a negligible effect on the formation of Ba6LiZ3. This view is further supported by the fact that the radius ratio, R/r, in other known "size-factor" compounds is observed to range widely—for example, from 1.08 to 1.45 for ABz-type compounds (C15, MgCuz type)&apos; and from 1.37 to 1.58 for AB5-type compounds (D2d, CaZn5 type).g The present investigation was undertaken in order to find a more satisfactory explanation for the non-existence of Ba6LiZ3 and, consequently, a better understanding of the nature of the A6Bz3-type compound. The primary objectives are to confirm the previous conclusion3 that the A6B23-type compound is indeed a "size-factor" compound and subsequently to determine the atomic-radius ratio range in which the A6Bz3-type compound can exist. In order to achieve these objectives, stoichiometric A6Bz3 alloys, where manganese (B) was alloyed with various lanthanide elements (A), were selected for investigation. The atomic-radius ratios of lanthanide elements with manganese range from 1.26 for Lu/~n to 1.46 for Eu/Mn. This radius ratio range includes and exceeds the range of all previously reported A6Bz3-type compounds—1.32 for Th/Mn&apos; through 1.38 for Sr/Li. Furthermore, the atomic-size difference between successive elements of the lanthanide series in order of atomic number) is of the order of 0.01A (europium and ytterbium are exceptions). The series of lanthanon-manganese alloy systems is ideally suited to a precise determination of the limits of allowable atomic-radius ratio for A6Bz3-type compound formation. EXPERIMENTAL PROCEDURE The lanthanide metals, in ingot form, supplied by Michigan Chemical Corp. (St. Louis, Mich.) and Nuclear Corp. of America (Burbank, Calif.), were guaranteed by the suppliers to be at least 99.9 wt pct pure (traces of silicon, calcium, and other minor constituents present on occasion, not to be more than 0.05 wt pct) as shown by spectrographic analysis. Manganese metal, in polycrystalline form, was redistilled from the commercial, chemically pure grade and was analyzed to be at least 99.95 wt pct pure. In all cases, the atom ratio between the two elements in each charge was A (rare-earth meta1):B (manganese) = 6:23 and a constant weight, 3 g, of

Jan 1, 1965

By Henry M. Otte, Ralph P. I. Adler

The changes of line position and integral line breadth in the X-ray diffraction pattern of a polycvys-talline Cu-30Zn tensile test piece, incrementally loaded (and unloaded) up to fracture, have been an-alyzed in detail. The stacking-fault probahility, cv, increased linearly with increasing strain, E, wheveas the effective domain size, De(hkl), decreased with decreasing E-1 Over the greater part of the stress-strain curve the rate of work hardening was essentially constant (about 86 kg per sq mwz), and could be correlated with the slope of stage II of the single-crystal stress-strain curve. Consequently the theories of work hal-dening (particularly those parts relating to stage 11) as developed by Mott and Hivsch and others could be applied to the observations made on the polycrystalline brass. A relationship of the form Aa = Aao - MhklEhkl between the change, Aa, in the extrapolated lattice pararneter and the rvns strain, Ehkl, was derived and found to fit the results acceptably well. From this and other relationships developed in the papev it was estimated that the equilibrium stacking-fault energy of Cu-30Zn was between 8.4 and 12.5 ergs per sq cm, in fuirly close agreement with the (corvected) value obtained by Howie and Swann (1961)43 using transmission electron microscopy. The theory of work hardening in the jorm developed and recently presented by Hirsch (1964)3 successfully described all the pvesent observations. In order to test certain aspects of the theories of work hardening, as developed by Mott,1 Hirsch,2,3 Seeger et el,4-7 and others (for review see Nabarro, Basinski, and Holt8), several recent investigations have been concerned with relating the dislocation density, p, with the shear stress, 7 (and strain, y), applied to the specimen. The results of these investigations have shown that the square root of the dislocation density appears to be linearly related to the applied shear (or flow) stress for fcc as well as bcc metals and alloys. Furthermore, the relationship appeared to apply not only to the deformation of poly-crystalline specimens, but also to stages I and I1 of the deformation of single crystals. An expression of the form has thus come into wide use. Here b is the Burgers vector for a total dislocation, G is the shear modulus, and 70 and q are constants. A review9 of available values of q shows it to have values (at room temperature) in general between 0.3 and 0.6. Forms of Eq. [1] can be deduced from, or predicted by, the current theories, and the various constants adjusted so that they are compatible with the experimentally found value of q . No unique relationship has yet been found between the dislocation density and the applied shear strain. There are several serious objections to the use of Eq. 11]. In the first place, it relates the shear stress to the density of the dislocations without regard to their arrangement, type, or distribution; the significance of the relation may therefore be justly questioned.5 In the second place, the values of the experimental quantities usually substituted into Eq. [11 are those of the applied shear stress and the total dislocation density measured after unloaditzg. The dislocation density value that should in fact be used is that for the mobile dislocations present in the specimen when under the applied load.* Finally, in cases where the values used for p, the dislocation density, are those obtained by electron microscopy, p is subject to considerable error,&apos; both systematic and random. The corrections to be applied are still controversial. Dislocation densities can also be measured by etch-pit and other techniques,&apos;&apos; each having their specific limitations. An objective of the present investigation has been to obtain information about the dislocation configyration and distribution by analyzing the changes in the position and shape of X-ray diffraction profiles as a function of deformation. The X-ray techniques employed, also open to criticism, have certain advantages, however. Thus, although the X-rays diffract only from the surface layers to an effective depth of about 20 p, the measurements can be made while the specimen is under load. The value of the dislocation density obtained by the X-ray method is also subject to errors, which are different from those of the electron microscope. Though a considerably larger volume of material is sampled by the X-rays, thereby reducing some of the statistical errors inherent in the electron microscope data, the information obtained is less detailed and is dependent on the method of analysis used to obtain a value for the dislocation density. Nevertheless, important observations can be made because the aforementioned advantages outweigh some of the limitations. In the present paper the X-ray method is briefly described and applied to a brass specimens deformed in tension. The results are then discussed in terms of some of the current concepts of work hardening. 1) EXPERIMENTAL PROCEDURE Details have already been extensively published elsewhere11-14 and therefore will only be dealt with briefly here. 1.1) Materials and Specimen Preparation. Commer-

Jan 1, 1968

By W. J. West, T. D. Mueller, J. E. Warren

Two methods are used to obtain the relatiorlship between ratio of gas to oil permeability and gas saturation. One method is to calculate a curve from field measurements of reservoir behavior: the other is to measure the relationship on a core .sample in the laboratory. The curves resulting from these TWO methods arc often comparer1 and seldom found to agree. The most important reason for the nonagreement is often overlooked. This reason is that the performance k9/k0 curve is calculated with the assumption of uniform pressure and saturution throughout the reservoir. To show the differerence between performance type kg/k0 curves and laboratory type kg/k0 curves. two performance type kg/k0 curves for two different production rates were calculaled from the production perforrnance of a hypothetical reservoir for which a laboratory type curve was assumed. Production performance of the hypothetical reservoir bras calcu- lated by use of international Business Machine&apos;s 701 Computer. The perfortnance type kg/k0 curves differed from the laboratory curve for the hypothetical reservoir. The performance type crrrve for the lowest production rate most nearly coincided with the laboratory curve. INTRODUCTION Predictions of oil reservoir performance are often made with the aid of complex numerical calculations. An important quantity required in these calculations is the ratio of gas permeability to oil permeability (kg/k0 )at a particular gas saturation. Two methods arc used to obtain a relationship between this ratio and gas saturation. The curves resulting from these two methods are called performance kg/k0 curves and laboratory kg/k0 curves. The performance curve is obtained from field measurements of reservoir behavior. Particular kg/k0 values are calculated from the producing gas-oil ratio, the cumulative reservoir withdrawals, the original oil in place, the average reservoir pressure, and the PVT properties of the reservoir fluids. The particular kg/k0 values are then plotted against the average rcservoir gas saturations for the entire history period. In order to use this derived kg/k0 relationship for performance predictions, a curve through these points is extrapolated to higher gas saturations. The laboratory kg/k0 curve is obtained from measurements made on core samples. Saturation is maintained uniform throughout the core during these measurements. The kg/k0 curves obtained with these two independent methods are often compared and seldom are found to be the same. Various reasons have been offered for the lack of correlation. One is that insufficient core? were obtained to derive a curve representative of the reservoir rock. Another is that laboratory methods have failed to reproduce reservoir conditions. The most important reason for the noncorrelation has been often overlooked because of the difficulty in evaluating its effect. This reason is that the performance or field kg/k0 curve is calculated with the assumption of uniform pressure and saturation throughout the reservoir. In any

Jan 1, 1956