Search Documents

By Kjell Winther

"Hydralift Scanmec introduced early in the eighties a new and different mill design for very large grinding mills. The design described has actually no size limitation upwards and is so far suggested with motor power up to 40 MW. The mill is furnished with gearless ring motor drive transmission. It is totally fabricated, without heavy castings. The first installation, an 8, 1 MW ball mill dia. 6,5 m x 9,65 m length, has been in continous operation in 13 years without problems. Total grinding costs has been reduced with 3 0% compared to traditional smaller mills. Reductions has been achieved in maintenance cost, power consumption, liner wear and grinding media consumption.So far 3 ball mills of the described design are delivered and in operation, one grinding Iron ore and two grinding Nickel ore.IntroductionThe design of mills for mineral ore dressing has basically been unchanged since grinding in mills started some I 00 years ago, in spite of the fact that mills have grown larger and larger. This has resulted in structural and mechanical problems, causing expensive failures and loss of production.Hydralift Scanmec engineers were designing mills for more than 20 years according to the old «rules». As they experienced interest for an increase in the mill size at the time when reports about failing mills were published, they started analyzing the different mill parts to find new solutions. One goal was to only use elements from proven technology in the new design. Two key items were ring motor (wrap around motor)(Isch et al. 1977, Meintrup and Klein 1982, Ranze 1983) and large diameter pad bearings (wrap around bearings)(Fuller 1984), both acknowledged from other industries."

Jan 1, 1995

By Chunhua Liao, Chao Peng, Guangsheng Huo

To get the separation of tungsten and molybdenum, we adjusted the pH of the solution to 7, at which tungstate (WO4 2-) will be polymerized into HW6O21 5-, while molybdate will still exist in the form of MoO4 2-. Two strongly basic anion exchange resins (D201, D213) were experimented for the separation of tungsten and molybdenum. The results of condition experiments indicate that D213 resin performs better in the treatment of lower concentration solution A (WO3 10g/L, Mo 4.12g/L) with a separation factor as high as 10.64. While D201 resin is more suitable for the high concentration solution B (WO3 70g/L, Mo 28.97g/L) with a separation factor of 6.9. The results of column testing performed on D213 resin show that the solution after loading process with a mass ratio of Mo/WO3 = 50 and the desorption solution with a mass ratio of WO3/Mo = 27 can be obtained

Jan 1, 2014

By Mukhopadhaya K. K, Cory A. H

The concept of using travelling magnetic fields created by linear motors was stimulated by Laithwaite who advanced ideas on motors with shaded poles (Laithwaite, 1968), rack and pinion motors (Laithwaite, 1970) as well as low speed, brushless motors and three dimensional motors (Laithwaite, 1973a and 1973b).Sudan (1963) and Sundberg (1969) had applied the concept to metallurgical processes. However, the use of travelling magnetic fields has not been used widely to produce conditions for the separation of magnetic from non-magnetic minera1s or even magnetic materials from non-magnetic materials, although some attempts were made by McCarthy (1922), Davis (1934), Dean, Gottschalk and Davis (1934) and Gottschalk (1934).Laithwaite (1973, a) while working with linear motors made suggestions for designing separators and in the work described here, the observations of Laithwaite and others are extended to determine the characteristics of the motor with a view to using it as a magnetic separator.

Jan 1, 1980

By H. H. Schrenk, Carlton E. Brown

"The purpose of this paper are (1) to present a broad picture of the recognized methods of measuring the various forms of atmospheric pollution; (2) to evaluate the significance of such measurements; and (3) to suggest suitable methods for obtaining comparative information on the concentration of contaminants in city air.The atmosphere (the gaseous envelope surrounding the earth) consists of a mixture of gases. These gases and their usual proportions are:4/The volume of water vapor in the atmosphere ranges from almost zero (in very cold weather) to about 5 percent arid averages about 1.2 percent.Strictly speaking, any other substance in the atmosphere or an excess of any of the substances mentioned (with the possible exception of water) is a contaminant. Needless to say, there are many contaminants in the atmosphere.In accordance with their physical state, contaminants may be classified as gaseous or particulate, and the latter may be classified as solid or liquid matter. Particulate matter, especially when dispersed in some medium such as air or some other gas, sometimes is referred to as dispersoid, and the complete system of gas and dispersoid is referred to as aerosol.All substances on the earth are potential sources of atmospheric contaminants. Combustible materials (particularly fuel for heating and power), sea water, earth or soil, metals, and animals (including man) are some of the important sources of contaminants.Ordinarily gases are produced by chemical processes, whereas dispersoids are produced by both chemical and physical processes. There are two general dispersoid-producing processes: (1) Condensation, in which molecules join to form larger units or particles, and (2) disintegration, in which large units are reduced to the particulate range (which for the purpose of this article may be considered to be from 100 microns, or 1/254 inch, down to molecular size) by such processes as crushing, grinding, abrading, and atomizing.“Condensoid"" is a convenient term for dispersoids formed by condensation, and ""disintegrasoid"" for those formed by disintegration. Solid condensoids are sometimes called ""fume,"" solid disintegrasoids ""dust,"" liquid condensoids ""fog,"" and liquid disintegrasoids ""mist.""5/"

May 1, 1942

Polyacrylamide flocculating agent has been used in the Leaching Division 'of the Risdon Works of the Electrolytic Zinc Company of Australasia Limited since October, 1960. The number of thickeners in the continuous thickening stage was thereby reduced from eight to three. There has been an increase of 25 per cent in throughput and a reduction of solids in thickener over-flow from 3-4 g/l. solids to 0·5 g Ir. solids. Reagent addition has been at the rate of 0·25 lb Separan NP10 per ton solids.Additionally there has been a gain of 3 per cent in current efficiency as the direct result of the addition of Separan NP10 to purified cadmium sulphate solution priOl; to electrolysis for cadmium metal. A smoother deposit has resulted and it has been possible to increase deposition time between strippings from 47 to 71 hr. However, there has been a slight increase in the lead content of the cadmium metal produced.The use of Separan NP10 to settle copper bearing residue in a batch process stage has resulted in a five-fold increase in settlement rate and a reduction in purification cycle time.INTRODUCTIONThe Electrolytic Zinc Company of Australasia Limited, Risdon, Tasmania, produces zinc by electrolysis of purified zinc sulphate solution, the raw material being zinc sulphide concentrate. In the Risdon process (Van Arsdale, 1953; J ohnstone, 1953; Ross, 1949) the compound zinc ferrite (ZnO.Fe203) is formed during the concentrate roasting stage. When the roasted material is leached in dilute sulphuric acid the zinc ferrite is not attacked, and it remains as part of the insoluble leach residue, of which it may form as much as two-thirds of the whole. The remainder is mainly unroasted zinc sulphide, unleached zinc oxide, lead sulphate, gypsum, silver compounds etc. The zinc in the residue may be 10 per cent of that in the original concentrate.Continuous thickeners are used to recover the valuable residue from the impure zinc sulphate solution and the...

Jan 1, 1963

By Orlando Gallardo

El presente texto describe la implementación del software ADS (Sistema de Despliegue Activo) a los sistemas de control supervisor de los diferentes procesos del complejo metalúrgico a nivel administrativo -en tanto replica los archivos gráficos y de base de datos. Este servidor además de concentrar en su red de campo redundante data de controladores e instrumentos de campo, puede compartir información con clientes usuarios y clientes de visualización dentro de la planta. En ese sentido, el objetivo es simplificar la producción y uso de datos únicos y garantizar la fiabilidad de estos a tiempo real para todos los niveles de supervisión a nivel administrativo, al tiempo que se planea y optimiza los recursos con la toma de decisiones apropiada.

Sep 24, 2008

By Brian Danyliw

"Dust control is an increasingly important consideration for all mining operations from a health, safety, environmental and maintenance perspective. Modern mining operations incorporate a variety of mechanical dust control techniques into design however in many cases these engineered systems are unable to meet desired fugitive dust level targets. In these cases a variety of chemical dust suppression options are available to operators to assist in meeting their targets. This paper provides an overview of available chemistries, discussion of application techniques and equipment requirements and available performance monitoring technologies. This paper will also include a number of case histories discussing the treatment approach chosen, challenges encountered, chemical feed, storage and application equipment, monitoring techniques employed and results achieved.INTRODUCTIONDust FundamentalsFugitive dust by definition is an aerosol consisting of particulate matter suspended in a gaseous medium. Aerosols can include suspensions of particulate (solids) or sprays (liquids) or a mixture of both. Of particular concern from an occupational health and safety perspective are aerosols of particulate matter due to their involvement in classical occupations lung diseases such as silicosis, poisoning through chronic exposure to compounds such as lead and beryllium and expected involvement in more modern identified conditions such as cancer, asthma, and a host of other respiratory and non-respiratory conditions which may be caused or influenced through exposure to dust.According to the ""Glossary of Atmospheric Chemistry Terms"" (IUPAC, 1990), ""Dust: Small, dry, solid particles projected into the air by natural forces, such as wind, volcanic eruption, and by mechanical or man-made processes such as crushing, grinding, milling, drilling, demolition, shoveling, conveying, screening, bagging, and sweeping. Dust particles are usually in the size range from about 1 to 100 µm in diameter, and they settle slowly under the influence of gravity."" It should be noted that the behavior of particulates with respect to settling rate in air is a function of particle mass and shape and therefore the geometric size of the particle can be misleading. Occupational hygienists utilize the concept of particle aerodynamic diameter as a more representative reflection of particle size. Particle aerodynamic diameter, is defined as ""the diameter of a hypothetical sphere of density 1 g/cm3 having the same terminal settling velocity in calm air as the particle in question, regardless of its geometric size, shape and true density."" The expression of particle size as aerodynamic diameter allows for a more consistent understanding of particle behavior both from a settling perspective as well as from the perspective of how dust particles will behave in the respiratory tract. Figure 1 illustrates settling rates for particles of various aerodynamic diameters. The relationship between particle size and settling rate is important for understanding what size of particles must be addressed by dust control strategies as well as what particle sizes represent the most danger from an exposure and occupational health perspective."

Jan 1, 2015

PolyMet Mining is developing the NorthMet property near Duluth, Minnesota. Laboratory investigations had led to the development of the PLATSOL process to dissolve in one step the base metals (copper and nickel) as well as the gold and PGM’s. To complete the pre-feasibility study, a fully integrated ten-day pilot plant trial was undertaken, comprising of: high temperature (>220ºC) pressure oxidation in the presence of 5-10 g/L chloride (the PLATSOL process), followed by solid/liquid separation, gold plus PGM’s recovery from solution, conventional Cu SX/EW and recycling of the copper raffinate to the autoclave. The concentrate tested was a NorthMet bulk flotation concentrate assaying 14.7% Cu, 3.05% Ni, 0.14% Co, 26.7% S, 1.4 g/t Au, 2.2 g/t Pt and 9.9 g/t Pd. Laboratory results were fully confirmed and with minor adjustments of the laboratory PLATSOL® conditions, the following leach extractions were obtained during the pilot plant trial: Cu 99.6%, Ni 98.9%, Co 96%, Pd 94.6%, Pt 96% and Au 89.4%.

Jan 1, 2001

Discussion of the paper of George K. Burgess, J. J. Crowe, H. S. Rawdon, and R. G. Waltenberg, Finishing Temperatures and Properties of Rails. By Albert Sauveur, R. Trimble, William R. Webster, P. H. Dudley, George B. Waterhouse, M. H. Wickhorst, James Aston, E. F. Kenney, A. W. Gibbs, W. A. Aiken, and G. K. Burgess . . 767 Discussion of the paper of Albert Sauveur, Manganese Steel and the Allotropic Theory. By G. K. Burgess and J. E. Stead 787 Discussion of the paper of J. V. Emmons, The Surface Decarbonization of Tool Steel. By Albert Sauveur, Bradley Stoughton, E. G. Spilsbury, Oliver W. Storey, H. O. Hofman, and J. V..Emmons 790 Discussion of the paper of Richard H. Rice, Turbo Blowers for Blast-Furnace Blowing. By S. G. Valentine, W. McA. Johnson, L. Iversen, J. E. Johnson, Jr., Karl Nibecker, W. Trinks, Otto Banner, H. S. Braman, Arthur G. McKee, and Richard H. Rice . . . 794 Discussion of the paper of J. K. Furst, The Plant of the Duplex Process for Making Steel. By W. McA. Johnson, Arthur G. McKee, Henry D. Hubard, and Bradley Stoughton . . 810 Discussion of the paper of E. C. Harder, The Iron Industry in Brazil. By I. C. White and E. C. Harder 813

Jan 4, 1915

Australian rutile and zircon concentrates are refined raw materials and not manufactured products. The composition and properties of the grains are therefore fixed by nature. Specifications and assay certificates should take this into account by eliminating unnecessary provisions which only increase the time and cost of analysis.INTRODUCTIONThe raw material from which Australian rutile and zircon concentrates are isolated is beach sand on the coast of New South Wales and Southern Queensland. The principal current operations are in an area between Sydney and Brisbane.The sands consist principally of quartz particles, but they contain from 1 per cent to 50 per cent of a mixture of heavy minerals, including zircon, rutile, ilmenite, monazite, leucoxenic grains, chrome spinel, chromite, garnets, corundum, topaz, brown spinel, olivine, epidote, clinozoisite, tourmaline, magnetite, hematite, and cassiterite. The major components are zircon (25 to 60 per cent), rutile (25 to 50 per cent), and ilmenite (5 to 50 per cent).The so-called leucoxenic grains are not a definite mineral species but an alteration product of which the major components are titanium oxides and silica in varying proportions.Primary concentration is by gravity, using spirals or various forms of pinched sluice (Pullar, 1962), the resulting concentrates being redressed on wet tables. During these processes, some of the lighter heavy minerals including leucoxene and impure rutile, which tend to degrade the final rutile and zircon concentrates, are eliminated.The separation of heavy minerals from each other is...

Jan 1, 1963

By S W. Robertson, A Vercuil, P Craven

Mintek is currently developing a design approach for the heap leaching of low-grade primary copper sulphide material. Since the leaching of chalcopyrite requires elevated temperatures, the generation and management of heat within the heap is crucial. Furthermore, the precipitation of iron needs to be managed to prevent premature blinding of the heap, and acid consumption needs to be limited to contain cost and limit the dissolution of gangue impurities. Standard column tests using jacketed 1-m and/or 6-m columns do not allow accurate prediction of temperature changes and heat generation in an actual heap. Mintek therefore utilizes a computer model to calculate the energy balance and heat generation with time, based on the measured sulphide oxidation rates in the column. The temperature in the column is then adjusted to reflect the computer-predicted temperature in an actual heap. Using this approach, an overall copper extraction of 70% was achieved in 120 days, using 1-metre columns, when treating an ore blend containing 1.36% chalcopyrite, 0.23% chalcocite, 0.07% covellite, 3.8% pyrite and silicate gangue (92%). The chalcopyrite contribution to the total copper content in the feed was 75%. This was followed by 6-m columns using a similar approach, and the column results will be validated on a 23,000 tonne test heap. Key Words: heap; bioleach; chalcopyrite

Jan 1, 2005

By P. J. Mehrfert

"Recovery of mineralized coarse particles is notoriously low in conventional concentrators that treat copper porphyry ores. The application of coarse particle flotation techniques has the potential to achieve comparable metallurgical performance at significantly coarser primary grind sizings. ALS Metallurgy has been conducting both internal research and commercial test programs to investigate the potential of Eriez HydroFloatTM technology on copper sulphide ores. Test data indicates that significant improvements in the recovery of copper sulphide bearing particles between 200µm to 850µm can be achieved using Hydrofloat technology compared to conventional flotation techniques. This paper summarizes the results from a selection of test programs that includes recovery by size data from both conventional flotation and HydroFloatTM tests. An explanation of the apparatus and test procedure will be given. Mineralogical analyses of the test products and characteristics that limit metallurgical performance will be discussed.Description of Apparatus and Test ProtocolThe HydroFloatTM laboratory cell is a clear plastic column with an internal diameter of 14 cm. Water and air are introduced to the cell through a circular manifold located in the lower portion of the cell. The cell has a conical bottom which directs slurry to a pinch valve that controls the discharge of tailings. Feed solids are introduced to the upper portion of the cell in slurry form. The cell is operated in a manner such that the manifold water creates a teeter bed zone of suspended solids in the middle portion of the cell. Tailings exit the bottom of the cell at a high pulp density, and most of the introduced water overflows the top of the column and is collected in a launder. Particles with a hydrophobic surface may attach to air bubbles that percolate through the teeter bed, rendering them sufficiently buoyant to be transported to the overflow launder.Three significant features of this arrangement enhance the potential to recover coarse, low grade particles by flotation techniques. Firstly, the hindered settling conditions created by the rising column of water allow coarse particles to become buoyant once attached to a modest sized air bubble. Secondly, the flow conditions within the cell are relatively quiescent compared to a conventional flotation cell that utilizes an agitator. This allows particles that have limited hydrophobic portions of their surface, due to a low content of exposed sulphide mineral, to maintain a somewhat fragile attachment to air bubbles long enough for successful recovery to the overflow. Finally, the absence of a froth phase at the top of the cell allows particles attached to air bubbles to immediately exit the vessel, reducing the potential to drop back into the pulp phase as bubbles burst or coalesce."

Jan 1, 2017

By Thomas J. Crocker, Douglas B. Uthus

Tunnel Boring Machines (TBM) have gained worldwide acceptance in the construction field and are being employed in ever increasing numbers to drive underground transit lines, drainage systems, etc. However, TBM utilization in the mining industry, and more specifically coal mining, has been very limited. This paper reviews past and present applications of TBMs to coal mining and examines the needs of the industry in an attempt to offer some insight as to what a TBM system must provide if the excavation potential demonstrated in civil works projects is to be realized in coal operations. EUROPEAN EXPERIENCE Germany The Germans recognized long ago the potential of mechanized drivage for coal mine entry development. Early in the 1960's experimental runs were made with a full-face Wohlmyer roadheader at the Westerholt Mine and trials were conducted on a roller bit armed full-face Bade roadheader. But because of problems with penetrating the various carboniferous strata occurring in changing sequence and hardness, these first attempts were soon terminated. After viewing later successes in the construction industry with improved TBMs, new attempts were initiated by the German mining industry in 1971 to mechanize drivage of their development entries. Four TBMs of two different types were placed in operation.

Jan 1, 1976

By Oliver Finn

Gold dredging has made such rapid strides of late and there is such a widespread interest in this branch of mining that I venture to contribute a detailed account of the way in which a Keystone driller was used by me in California to loosen, by blasting, a very tight gravel deposit, preparatory to dredging. There is a great difference between “cemented gravel” and “tight gravel.” A truly cemented gravel is not a dredging proposition, while the tightest possible gravel, where there is no cement, can be made easy working by the following method of blasting:

Jan 1, 2008

The development and introduction of a preventive maintenance scheme in the coke ovens department, coal preparation section, of The Broken Hill Proprietary Co. Ltd., Newcastle steelworks, is described together with its operation and the results achieved during the first 12 months.'fhe scheme consists essentially of an engineering analysis of the plant to establish maintenance schedules, and to record the details on reference cards.Items are reviewed progressively and a weekly work schedule is prepared, from which work orders are passed on to the maintenance foremen. These foremen in turn originate action orders and issue inspection sheets as required. Results are then reported back to the maintenance planner and used to revise norms, practices, and cycles.INTRODUCTIONWhat is maintenance? Some people consider maintenance to be the work involved in putting things together again after they have fallen apart. The author regards it as the mechanical care and repair of plant machinery and equipment to keep it operating in sound mechanical condition, without undue interference with production processes.Maintenance may be organized or haphazard, and, too often, what has been fondly imagined to be nicely controlled and organized maintenance proves, under pressure, to be more correctly described as haphazard. Haphazard maintenance deals with breakdowns as they occur, and frequently finds itself confronted with more breakdowns than can be handled. Even organized maintenance, if not based on sound planning, can, at times, be found in a chaotic state, because of unexpected and unanticipated breakdown.Properly planned and scheduled maintenance permits an orderly and controlled approach to the problem of maintain...

Jan 1, 1961

By Francis Foley

INTRODUCTION DURING the summer of 1919, the late Dr. Henry M. Howe, then Chairman of the Division of Engineering of the National Research Council, organized a committee to obtain a better insight into the behavior of carbon steels under the influence of various treatments by a proper control of the time and temperature factors. During part of 1919 and 1920, work in connection with this investigation was carried on at Dr: Howe's laboratory at Bedford Hills, N. Y. During 1921 there was an enforced hiatus in the work, occasioned by the illness which resulted in Dr. Howe's death in 1922. At that time one of the present authors compiled the results of the work which had been done and this was published in 1923.1 Following the publication of this work, it seemed desirable to carry on in the same manner an investigation of steel of C 0.75 per cent., which steel had not been as fully treated as had the other steels of C 0.34 and 0.52 per cent., used in the published work. Furthermore, certain unusual results have been obtained in the treatment of C 0.52 per cent. steel by quenching and drawing, and repetition of this part of the work seemed advisable. This has been done during the past year at the School of Mines and Metallurgy of the University of Missouri at Rolla, Mo., by a cooperative undertaking of the School and the Bureau of Mines, working in conjunction with the Committee on Heat Treatment of Carbon Steels of the National Research Council. The present paper is a report of the results obtained in this work.

Jan 2, 1926

By J Parr, P Ashworth, S Johns, C Yeats, A Littleboy

The ocean floor is increasingly being discussed in terms of its resource potential. New discoveries, improved knowledge and access to unexplored areas of the deep sea and continental shelf are some factors contributing to a renewed interest in the seafloor exploration and mining industry. The industry has been referred to as the ænext minerals frontierÆ. To date, much of the research has focused on proving economic and technical viability of the industry, with environmental issues addressed locally. However, there is limited research internationally, and none known in Australia that considers the social viability of the industry, addressing issues such as regulatory contexts, international precedence and public acceptability. Does the nascent seafloor exploration and mining industry have a social license to operate? Does it have support amongst the wider community? If not, why not? The Wealth from Oceans National Research Flagship explored these questions by scoping the social issues that would surround an expansion. Two desktop studies provide insight into the current level of activity in seafloor exploration and mining, recent developments and the regulatory regimes on which the industry is based. One study focused on the situation in Australia, while the other was internationally focused. A series of workshops were held with key stakeholders from government agencies, industry and other interested parties, such as environmental groups and the fisheries industry. These workshops identified and explored the different stakeholdersÆ perceptions of the benefits, concerns, opportunities and key questions associated with an expansion of the seafloor mining industry. The desktop studies revealed that Australia is one of only a few countries with legislation specific to seafloor exploration and mining. Nevertheless, barriers to licence approval exist because of lack of precedent in applying this legislation. Consequently, the decision process can be vulnerable to political issues and subjective judgements. The outcomes from the stakeholder workshops suggest this inconsistency may be influenced by the high levels of concern and uncertainty over environmental impacts. Uncertainty over environmental impacts can influence the acceptability of an environmental impact assessment (EIA) and also mean the perception of risk is variable. Overall, this research suggests that the future of the seafloor exploration and mining industry will be highly dependent on AustraliaÆs ability to:improve the knowledge-base underpinning the regulatory regime,generate open and transparent communications between stakeholders, andimprove the understanding of policy and regulatory processes.

Jan 1, 2008

By G. A. Apell, E. G. Howe, S. W. Hazen

"INTRODUCTION As a small amount of manganese was produced from the Lake Valley mining district of Sierra County, N. Mex., during the First World War, the district was reexamined in March 1941 by John H. East, Jr., an engineer of the Bureau of Mines, as a possible source of manganese for use during the Second World War. Preliminary examination indicated a substantial reserve of 25 percent ore, so it was recommended that an exploratory program of mapping and sampling be undertaken by the Bureau.The program was started in the fall of 1941 and was completed the middle of 1942. The project 3/ was divided into two parts: The first, an underground sampling program, formed the basis for the second, or churn-drilling program. Mapping and sampling of old underground workings were begun in October and finished in November 1941, whereas churn drilling was begun in February and completed in June 1942."

Jun 1, 1947

By Ali Ameli

Design loads are limited for piles relying upon toe stresses in rock due to uncertainty about the rock quality over the whole pile diameter because of rock mass properties or construction effects. The paper discusses the use of video images to evaluate rock quality at the bottom of piles socketed into graniodorite bedrock in a steel pipe pile project. Skillful interpretation was required to assess the 3D properties of the rock from video images. It is necessary to observe the rock mass characteristics near the project site for better perception of the rock features from the images. Video image interpretation skills were established by the evaluation of the cores drilled under the socket base and the results of pile loading tests. Correlations were found between rock appearance in the images and the rock socket drilling records. Rock socket acceptance criteria were developed through monitoring the drilling operations for the specific site procedures. Video images then served as one of the quality-assurance tools together with probing and pile loading test. Lessons and methods learned from video inspection in this project could be used to evaluate rock quality in similar cases.

Jan 1, 2006

By Dominic Fragomeni, Tony DiFeo, Martyn P. Hay

"As part of an investigation into flotation modelling of industrial scale operations, Falconbridge Ltd organised a “blind” test of the SUPASIM flotation model developed by Eurus Mineral Consultants (EMC). Two sets of rougher rate data, a flowsheet and the number and size of cells in the rougher bank were supplied from a plant that had been previously surveyed in November 2003. The name of the plant, cleaner circuit details and circuit mass balance were, at the time, unknown to EMC. With only these data, flotation performance was simulated and the cleaner circuit sizedFalconbridge then compared predicted and actual float performance and mass balance and found that final concentrate recovery and mass and circuit cell volume matched closely. Simulated recoveries relative to actual were +0.4% Cu, +0.1% Ni and -0.7% Co. However, prediction of metal distribution in the internal streams making up the various circulating loads showed some sizeable errors. On this initial success, the trial was extended and additional float test data for rougher feed, cleaner feed and cleaner scavenger feed was generated on site in April 2005. Further simulations significantly improved prediction accuracy for metal distribution in the internal streams. The average difference between predicted and actual recovery for all streams was reduced from 10.5% to 0.4%. This updated simulation was then used to ascertain the impact on final recovery, grade and plant circulating loads of increasing feed tonnage from 114 to 150t/hr. A number of scenarios were simulated in order to understand the contribution that (a) the fast and slow floating fractions and (b) regrinding of cleaner tailings are making to overall plant recovery.Simulation was then used to determine how much the flotation kinetics of both rougher feed and cleaner scavenger feed have to increase in order to deliver a 1.5% improvement in overall plant recovery. These improved kinetic values provide a target for laboratory testwork and operating conditions can be varied to determine how best to achieve these new values of fraction and rate."

Jan 1, 2006