Search Documents

By Raymond W. Henn, Kent A. Pease, Glen J. Rorison

The paper focuses on construction of a 2.55-km (8,365-ft) long, 2.4-m (8-ft)diameter storm drain tunnel in Evansville, Indiana. The tunnel was driven through saturated soft ground varying from clay to fine sand. The paper presents: an overview of design and design rational including specific EPB machine requirements; the contractor’s proposed and accepted alternative construction methods and TBM design; and construction issues and performance. Some of the key points discussed are the use of the TBM in different operational modes for alternative ground conditions, the effectiveness of dewatering systems, production rates, and issues such as surface settlements and gas.

Jan 1, 2001

By Juan Kobashicawa, Bernardo Falcón

En este trabajo se explican los controles automáticos desarrollados (In-House) e implementados en el circuito de Molienda de Compañía Minera Antamina, el cual abarca Molinos SAG, de Bolas y los Hidrociclones respectivos. Los controles implementados son basados en el Control por Lógica Fuzzy y las Bandas de Bollinger; así mismo se indican los criterios en el diseño de los controladores y las variables del proceso que se han tomado para la implementación donde se controla un indicador de distancia del centro de masa de la carga respecto al centro del molino de Bolas. Asimismo, se muestra el impacto positivo logrado con la estabilización del circuito.

Sep 1, 2017

By Nicholas Chlumecky

One of the oldest mine supports in use today is timber cribbing. In many mining operations material, installation and maintenance costs for timber cribbings are substantial. Their performance characteristics also add to mining costs. During the 1970'6, the U.S. Bureau of Mines recognized many of the deficiencies of timber cribbing and very successfully initiated the development of steel-fiber- reinforced (SFR) concrete blocks. Since the early 1980's this SFR concrete cribbing has been manufactured as a high quality product which has found increasing acceptance by mine operators. The rapid acceptance of the SFR concrete block cribbing has proven that its use is eliminating many of the deficiencies of timber cribbing while providing superior load carrying capability. The use of SPR concrete blocks to build the cribbing is based on the same principle as wood. That is, stacking longitudinal, rectangular blocks in layers in a crisscross manner. The blocks are positioned at right angles to the blocks of the layer below. With this situation, the possibility of misalignment exists when the concrete blocks at the base are not placed exactly parallel or when the blocks of the base are subject to unequal settlement. Such misalignments creates localized, high stress areas which reduces the load capacity of the cribbing made from SFR concrete blocks. Recognizing the problem of misalignment, the Underground Supports Division of Commercial Shearing, Inc., conceived a circular, one-piece, steel-fiber-reinforced concrete cribbing which is being marketed under the name - Donut Cribbing. This concept eliminates the possibility of misalignment and provides 100% bearing between layers of stacked cribbing as well as other advantages. The purpose of this paper is to discuss the performance characteristics, installation speed and economical factors of each of the three cribbing types -- timber cribbing, SFR concrete block cribbing and SFR concrete Donut Cribbing.

Jan 1, 1986

By Y. I. Yang, Y. -B. Tang, D. -J. Ma

Chlorine-containing minerals are commonly present in coal. Associated minerals such as pyrite can undergo exothermic reactions. Consequently, it is of great significance to study the effect of inorganic chloride on the spontaneous combustion of coal. In this study, the effects of five inorganic chlorides (sodium chloride, magnesium chloride, potassium chloride, calcium chloride, and zinc chloride) on the spontaneous oxidation of coal were investigated. Analysis of the gaseous products of coal oxidization at low temperatures (323K to 453K) showed that the presence of inorganic chlorine in coal markedly decreases O2 consumption and the generation of CO and CO2. Samples of raw coal and chlorine-loaded coal were oxidized for 36 hours under the same experimental conditions. Infrared diffuse reflectance spectroscopy results showed that inorganic chloride can inhibit the oxidative decomposition of some functional structure components (methyl, methylene, methine, and hydroxy) in the coal. The influence of inorganic chloride on the oxidation characteristics of the functional groups in coal during spontaneous combustion was investigated using benzyl alcohol and 1-phenylpropanol as model compounds, which were tested under the same experimental conditions as the coal samples. The oxygen consumption of model compounds with and without the addition of inorganic chloride further suggested that inorganic chloride may hinder the oxygenolysis of these structures during low-temperature oxidation. This phenomenon can be attributed to the radical reaction from the perspective of radical chemistry. It can therefore be concluded that inorganic chlorides play an inhibitory role in the spontaneous combustion of coal.

Jan 1, 2015

By J. B. Elizondo

This paper, which describes mining methods and practices at the Piokee mining unit and the Piokee expertmental mining project of The Eagle-Picher Co. in northeast Oklahoma, is one of a series being prepared by the Federal Bureau of Mines on mining methods, practices, and costs in various mining districts of the United States. The Piokee unit, comprising the Piokee, Rowe, Lucky Syndicate, and parts of the Netta White and Otis White leases, is in the SW1/4, W1/2NW1/4SE1/4, and W1/2SW1/4SE1/4 sec. 17, T. 29 N., R. 23 E., Ottawa County, Okla. (figs. 1 and 2), The 200-acre tract is adjacent to the town of Picher and near the heart of the Picher field of the Tri-State zinc-lead mining district.

Jan 1, 1959

United Engineering Trustees, Inc. TAMES L HEAD, '50 E C MEAOHER, '52 R M ROOSEVELT, '49 The Engineering Foundation F F COLCORD, '50 E A PRENTIS, JR , '48 R M ROOSEVELT, '49

Jan 1, 1952

By N. E. Hanna

The current list of permissible explosives includes 124 different brands. Fifteen of these are gelatinous, and the rest are the more commonly used granular ammonium nitrate type. Their rates of detonation range from 1,300 to 5,600 meters per second, and the weights of 1-1/4 x 8-inch cartridges range from 86 to 244 grams. The list of permissible blasting devices includes 1 Cobra, 2 Hydrox, and 9 Cardox models. All of these devices are based on discharge of high-pressure gas from a pressurized shell in a shothole. INTRODUCTION To be approved for use in underground coal mines in the United States, explosives and blasting devices must pass certain schedule tests prescribed by the Bureau of Mines. The explosives listed here were tested under Schedule 1-G,3 which has since been replaced by Schedule 1-H;4 the blasting devices were tested under Schedule 26A.5

Jan 1, 1962

By K. A. Lewandowski

Leach heaps are plagued with problems due to fine material migrating downwards, clogging the spaces between the coarser ore particles, resulting in decreased metal recovery rates. The use of a binder in agglomeration would allow the fine material to be immobilized, increasing the availability for the solution to come in contact with all the ore. As much as 1.64*1012 BTU per year would be able to be saved if a 25% increase in copper recovery was experienced, assuming that 70% of heap leaching units converted to using agglomeration technology. This is equivalent to approximately 18% of the energy currently being used in leaching heaps.

Jan 1, 2008

By D. E. Healy

In 1989, an autogenous grinding task force was formed to study potential autogenous grinding circuits to replace the existing semi-autogenous grinding (SAG) at the National Steel Pellet Plant in Keewatin, MN. Pilot plant test work, performed by the Hanna Research Center (HRC), indicated that fully autogenous grinding with pebble extraction and crushing could be incorporated into the existing circuits. In 1990, one of the existing 10 grinding mills was converted for an in-plant test incorporating pebble crushing. Full-scale test work were conducted in 1990 and 1991. They verified the pilot plant projections with primary mill throughputs from the fully autogenous circuit using pebble crushing being greater than throughput of the existing SAG mill circuits. The plant produces 5 Mt/a (4.9 million ltpy) of iron ore pellets from 17.6 Mt (17.3 million It) of crude taconite. Crude ore is single-stage crushed by gyratory crushers. Primary grinding is performed by 10 semi-autogenous wet grinding mills. Secondary grinding is performed by five ball mills. Induration is with an Allis Chalmers grate-kiln pelletizing system. The primary grinding circuit consists of 108.2-m-diam x 5.5-m long (27 ft-diam x 18-ft) SAG mills. The mills are charged with 127 mm-diam (5 in.diam) steel grinding balls at from 3% to 5% by volume. Ball consumption rate is about 0.55 kg/t (1.25 lbs/lt) of crude ore feed to the mill. Each SAG mill is powered by two 2.6 MW (3500 hp) motors drawing 5450 kW (7300 hp) at 76% of critical speed. The mills are grate discharge with 16 mm (0.6 in.) slotted grate openings when new. The mill discharge is sized on a trommel screen having 4.5 mm (0.2 in.) openings. The plus 4.5 mm (+0.2 in.) oversize material is returned to the discharge end of the mill by a reverse screw auger located in the center of the trommel. The -4.5 mm (-0.2 in.) trommel screen undersize is pumped to magnetic cobbers.

Jan 1, 1992

By D. Boshoff

The ability of an explosive to break rock is influenced considerably by the extent of confinement in the blasthole. It is believed that confinement is improved by the use of adequate stemming. The aim of this paper is to present the results of the first and second stages of developing a stemming performance testing rig for small diameter boreholes. The rig was used to compare and contrast the performance of different designs of products. The results showed that different stemming products have differences in terms of their functionality, which can have a major impact on the efficiency of rock breaking. Two test procedures were used, one through the exclusive use of compressed air and the second using a purpose-built high pressure test rig with small quantities of explosives. Both tests were used to identify and evaluate the ability of various stemming products to resist the escape of explosive gas through the collar of a blasthole. An investigation was done to determine the types of stemming products most commonly used in South African underground hard rock mines, and these products were used during the tests. The first stage of tests using compressed air only did not prove adequate to predict with certainty the pressure behaviour in the borehole of a particular product under high pressure conditions. The purpose-built high pressure test rig also did not prove to be a very effective tool to test stemming products under high pressure conditions. The test rig incorporated only the effect of gas pressure on the stemming product, and excluded the effect of the shock wave. This study therefore proved that to take into account only the gas pressure generated in the blasthole is not sufficient to effectively test stemming product performance.

Jan 1, 2011

The effect of composition on electrical conductivity (resistivity), viscosity and liquidus temperature of the slags encountered in electric smelting of PGM-containing suphide concentrates is reviewed along with the relationsip between slag composition, slag-matte separation and metal losses to slag. Optimization of slag composition at furnace temperature is attempted on the basis of opposite and parabolic trends of the viscosity-conductivity relationships of the slags. The importance of surface tension of slags is emphasized using available and estimated information, which are grouped into a useful correlation. These values are coupled with or incorporated into slag viscosity plots to illustrate the correlation between the two factors which influence slag-matte separation as well as refractory attack. The electrode in the slag-resistance furnace is the central factor in the design and operation of the furnace by its role of conveying the smelting power. The obvious parameters are the size and positioning in the slag bath, which are defined by slag resistivity, furnace resistance, cell constant and power input. The flow of heat generated by the electrode current determines the energy distribution and furnace dimensions creating viscosity profiles, which in turn affect flow conditions. Thus the flow of slag and matte isdiscussed in conjunction with the furnace geometry, stirring action of the electrodes, buoyancy and electromagnetic effects. The action of the electric furnace as a settler is discussed. The rectangular furnace is considered as a channel reactor in this analysis and the action of the electrodes is described to indicate a balanced settling rate in the area of electrode action. Discussion of the design and production capacity of the electric furnace with reference to operating current, power input, furnace dimensions and electrode size are based on considerations derived mainly from slag properties such as its resistivity, viscosity and liquidus temperature.

Jan 1, 2004

By Edgardo Fogli, Mario Lampiano, Antonio Nicola

The project is located in the northern region of the People’s Republic of China and was awarded to Impregilo, as sponsor of the Wan Long Joint Venture, in September1997. The project consists of four tunnels for a total length of 88,700 m, with an excavation diameter of about 4.9 m. The lining is made of honeycomb pre-cast segments, connected by PVC dowels and the joints are sealed with elastomeric gaskets. The geology is mainly Limestone, Dolomite and Sandstone. Karst cavities are abundant and are often in-filled with plastic red clay. This has adversely affected the TBM’s progress. Four double shield telescopic TBMs were mobilized to cope with the very tight construction schedule and, at the end of November 2000, more than 80% of the tunnel has been bored. The article analyses the TBMs’ productions in the various geological conditions and the results of different technical solutions adopted at the project.

Jan 1, 2001

The achievement of high availability of the Grey River Gold Mining Limited's alluvial gold dredge is a tortuous task which will rely upon the dedication of all staff employed at Grey River Gold Mining Limited (GRGML). The persistent adoption of new technology and better operating procedures, combined with a strong commitment to preventative and predictive maintenance, is necessary. The Grey River Gold Mining Limited alluvial gold dredge is operating in a relatively low grade alluvial gold deposit and hence relies on a high throughput of ore to be profitable. To achieve the required high material throughput the dredge incorporates an overburden removal system which operates simultaneously with a conventional bucketline system.   The overburden system incorporates a cutter wheel and suction pump configuration which is dedicated to removing the low grade (5 mg gold/m3 gravel) overburden. The bucketline conveys the richer grade payzone gravels (up to 890 mg/m3 gravel) to the recovery plant mounted onboard the dredge. The horizon for the overburden system approximates 15 m and the payzone terminates at the interface of the old man rock and the alluvial gravels at a variable depth averaging 22 m.   From a mechanical engineering perspective the dredge is a machine comprised of two materials handling systems which are controlled by Operations Staff and electronic process control systems.   The availability of such a materials handling system is a function of four variables: 1. The environment that the machine operates in. 2. The ability of the people operating the machine. 3. The design of the mechanisms, the configuration that they are grouped in and the effectiveness of the process control systems which control the mechanisms. 4. The procedures utilised to predict the performance of the machines and the skill of staff to analyse that data and carry out effective maintenance.

Jan 1, 1989

By Jim Morris

This paper will describe the excavation of a 5.4 percent decline at the Montanore Project for Noranda Minerals Corporation. The 5.3 m by 4.9 m tunnel was driven to provide access for the exploration of a major copper-silver deposit. Soft ground and conventional drill-blast mining were used on the 4,270 m tunnel. Ground support consisted of steel sets and concrete in the soft ground and pattern rockbolts providing the majority of the rock support. A special feature of the project was the use of conveyor haulage in conjunction with the drill-blast excavation.

Jan 1, 1993

By Christopher J. Pacitto

This paper presents a case history of an engineered, monitored, and tested program that provided an effective and satisfactory basis for the completion of pile foundations for Twin Dolphins 1 at La Peninsula Condominiums located in the Isles of Capri in southwest Florida, U.S.A. An 8-story building (withl-story parking underneath) along with recreational facilities (such as a swimming pool and tennis courts) had been planned for final construction. Following an evaluation of various foundation alternatives, a precast prestressed concrete (PPC) pile-supported system was selected. The building foundations were designed for pile capacities of 445kN (50 tons) and 890kN (100 tons) in compression and 133kN (15 tons) in uplift. A test pile program was performed to provide site-specific pile driving data, verify design assumptions, determine production pile lengths, and evaluate pile driving criteria. A total of 24, 356 mm (14-in.) square, 19.8 m (65 ft) PPC concrete piles were driven and dynamically load tested utilizing a Pile Driving Analyzer (PDA) within the building limits. Dynamic monitoring during probe pile installation and restriking was performed to estimate the ultimate capacity of the piles and to evaluate driving stresses during installation. CAPWAP analyses were preformed on PDA data to better estimate pile capacity, resistance distribution, and predict pile freeze (increase in pile resistance with time) and thus optimized the production pile lengths. Upon completion of probe pile installation, 12 of the probe piles were tested using the Pile Echo Tester (PET) function of the Pile Integrity Sonic Analyzer (PISA). PET testing was performed to evaluate the integrity of piles which had exhibited high driving stresses during PDA testing. Information gathered during the probe pile driving program was effectively utilized as part of the overall quality control program to install a total of 539 PPC piles (including 24 probe piles) within the building limits at the project site to depths ranging from 9.1 to 19.8 m (30 to 65 ft) below the existing ground elevation as part of the foundation support system. Prior to installation of probe or production piles, a termination criterion was established using 1-dimensional wave equation analyses in addition to the design pile embedment requirement. The predicted pile capacities compared very well with the capacities from the CAPWAP analysis for probe piles. Use of geotechnical instrumentation and PDA assisted technology enabled each foundation support element to be constructed to its optimum capacity and at optimum cost. Furthermore, by using PDA the consultant was able to quantify a difficult to measure geotechnical phenomenon termed "pile freeze" which eliminated costly overdriving and unnecessary splicing of piles.

Jan 1, 2002

By G Siboni, A Correa De Araujo, M Gotelip Barbosa, M J. Venturini

In support of the development of its Liberian iron ore project, ArcelorMittal Mining Research and Development (AM Mining R&D) has performed characterisation and beneficiation test work on drill core samples received from the proposed mine area. In addition to this, a sinter feed product was composed by blending and processing the drill cores in order to predict sintering performance of the ore. This article presents the methodology used to prepare the drill core blend for characterisation, as well as describe the sinter pot trial. The results are presented, demonstrating how important this type of study is for the development of an iron ore deposit.CITATION:Gotelip Barbosa, M, Siboni, G, Venturini, M J and Correa de Araujo, A, 2017. The use of drill core blends to predict sintering performance, in Proceedings Iron Ore 2017, pp 297–302 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

The need for legislative reform of health and safety legislation has been recognised in New Zealand for about a decade. Previous legislation did not cover all work places, many areas were excluded from coverage, and there were at least 14 different acts and dozens of sets of regulations dealing with various aspects of health and safety.

Jan 1, 1993

By Pradeep K. Rohatgi, David N. French, Surendar M. Jain, Clyde M. Adams

The effect of solute concentration and diffussivity on dendritic solidification of dilute binary aqueous solutions has been investigated; chlorides of sodium, potassium, lithiurn, and hydrogen were used as solutes. Dendrite spacings were measured in spherical droplets and in unidirectionally solidified specimens. In the droplets, the freezing rate is uniform over the entire specimen and remains constant from the beginning to the end of solidification. In the unidirec-tionally frozen specimens the freezing rate varies within a given volume of liquid during the solidification cycle; in addition, it varies with location uithin the specimen. Mass transport analysis has been used to calculate the supersaturation, AC, supercooling, AT, and transcerse growth velocity, V , of ice dendrites during solidijication from the dendrite spacings measured in the droplels. The ice dendrite spacing in a given solute increases lineary with the solule concentralion at a fixed freezing rate. The ualues of AC, AT, and V increase with an increase in solule concentration. The value of AT in the aqueous solution is of the same order of magnitude as in Al-Cu alloys of the same concentration; the dendrite spacings in Al-Cu alloys also increase with an increase in solute concentralion. For the jamily of aqueozrs solulions incestigaled, the dendrite spacing increases linearly with solute diffusivity at fixed values of concertralion and freezing ,rate. The values of ?C and ?T decrease, whereas the value of V increases with an increase in solule diffusicity. The measured dendrite spacings , L, can be expressed by the relatiun: L = K;(dfa/db) 4 K2C +K3D - K4 where dfs/d? is-change in fraction solid with time (freezing rate), C is solute concentration, D is solute diffusivit K1 = (14 * 4)pmin1'2, K2 = (70 ± 10) pl (moles)- K3 = (24 r 3) . l05 psec (cm)-~. K. = -132 ± 10) 1. FREEZING of solutions is almost always an ehunmix-ing" process because the composition of crystallizing solid generally differs from that of the parent liquid. " Solute concentration and transport are therefore in]portant considerations in solidification of solutions. The influence of these factors on the dendritic solutions produced from metallic solutions is of practical significance since the properties of the solid aggre-gate are often strongly influenced by dendrite spacing.''' Alexander and Fthines3 found that dendrite spac- ings generally increase with solute concentration in several metallic systems. Michael and Bever1 have observed an increase in a aluminum dendrite spacings in dilute A1-Cu alloys. Rohatgi and AdamsJ have reported a linear increase in a aluminum dendrite spacings with increasing copper contents up to 28 pct in A1-Cu alloys. Bolling and Tiller"' have theoretically examined the effects of solute concentration and diffusivity on the growth of cells and dendrites. Their analysis of dendritic growth assumes a steady-state growth and the maximum possible velocity for dendrite propagation. In addition, the quantitative analysis is restricted to dendrites of rotational symmetry and is therefore not directly applicable to the plate-shaped dendrites of ice obtained in the present study. There are practically no experimental observations of the effect of solute diffusivity on dendrite spacings in metallic systems. The reason appears to be the lack of experimental data on solute diffusion coefficients in liquid metallic solutions. The present work is concerned with the effect of solute concentration and diffusivity on dendritic solidification of dilute aqueous solutions: the solutes examined are potassium chloride. sodium chloride, lithium chloride. and hydrogen chloride. There were several reasons for selecting these solutes. The variation of dendrite spacing with freezing rate in these solutiolls is similar to that observed in A1-Cu alloys.8 These aqueous solutions have almost identical phase diagrams at dilute concentrations. Fig. 1. and the diffusion coefficients show very little variation with solute Concentration.9,10 Dendrite spacings were measured as a function of freezing rate. solute concentration. and solute diffusivity. Dendrite spacings were measured in two different types of freezing systems. droplet and unidirectional, respectively. In the droplet freezing system

Jan 1, 1970

The Leigh Creek Coalfield is owned and operated by the Electricity Trust of South Australia to supply fuel to the Northern Power Station. To supply electricity at lowest cost, a costing and decision process that establishes the role of the Leigh Creek Coalfield in the overall system planning and operation is required. The costing is integrated in that it is based not just on a particular mine plan but on the wider need to supply a particular electrical demand. The detail costing has evolved over time from manual to main-frame computer to microcomputer techniques. Now there is a choice between fast consistent costs and a slower but more detailed and flexible costing.

Jan 1, 1990

By Miche1 Dagbert

In most open pit operations mining porphyry type deposits, production planning rests on an are reserve inventory block file which is derived from diamond drill hole data. With such a practice, the way by which block values are generated is critical and in the recent years many studies deal with the comparison of different estimation methods for block grades (Mueller, E. (1), Knudsen et al (2) (3), Barnes, (4), Williamson and Mueller (5). Typically in such studies, one selects a bench or a group of benches where there is a "sufficient" number of blast holes (BH) with assay values in each of the blocks (generally 30.5 x 30.5 m (100 x 100 ft) or 15.2 x15.2 m (50 x50 ft). Then the arithmetic mean of the BH values in each block is computed and it is assumed to represent the real block grade against which different estimated values are compared. However it is sometimes observed that the variation of these BH values within a block is high and that their arithmetic average may significantly differ from the real average grade of the block (Barnes (4). The problem of the precision of the mean BH grade in a block has been examined by Williamson and Langlois (6) in an experimental way. They strove to find a better estimate of the average block grade than the mean BH grade but their results were not conclusive. The purpose of this study is to investigate the same problem within the frame of geostatistical models (David (7). Besides practical results obtained with these models, two general points are emphasized and illustrated in the text. First, "good results" are obtained if "good geostatistics" is done (David et al (8).

Jan 1, 1978