Search Documents

By Mei Yang, Wei Gao, Jian Yang, Qingcai Liu, Wenchang Xi

"TiO2 has been loaded on cordierite porous ceramic to prepare the SCR catalyst carrier by using both APCVD and sol-gel technology. In APCVD method, TiC14 and O 2 were used as reaction precursor. TiC14 was gasified by using N2 as carrier gas which was controlled to 500sccm. Its reaction temperature and reaction time were limited to 773K and 30min respectively. The physical properties, SEM and SEM-EDX of the TiO2-cordierite carrier and the properties of SCR catalysts prepared by these carriers have been tested. The tests showed that TiO2 loaded by APCVD method were of graininess shape and even accumulation. The loading rate of TiO2 and the specific area of carrier sample were increased 114% and 21 % respectively comparing with sol-gel technology. In the result of sol-gel method, the maximal difference of Ti content was 66.92%, while the result of APCVD method was 18.89%. It demonstrated that TiO2 was uniformly attached with the cordierite ceramic by using APCVD method, which would ensure more active ingredients well loaded on the Ti02-cordierite carrier. This difference made the denitrification ratio of catalyst prepared by APCVD method was 8.1 % higher than that of catalyst prepared by sol-gel method.IntroductionIn recent years, the emission of NOx, which were caused by coal-fired power plants, has gotten more and more attention. SCR (selective catalytic reduction) is the most effective technology to DeNOx [ll. The core technology of it is the catalyst. The SCR catalyst usually uses Ti02 as the carrier, and V2O 5 as the active component [2, 3] . However, the thermal stability and mechanical properties of TiO2 carrier are unstable, which would influence the performances of the catalyst. The commercial catalyst generally uses WO3 or MoO3 to promote its heat stability at present [4-7] Besides, TiO2 is expensive. Compared with TiO2, the cordierite is of good thermal stability and lower price. So loading Ti02 on cordierite porous ceramic as carrier to produce SCR catalyst is of good prospects [S, 91 • Currently, TiO2 is usually loaded on cordierite by the sol-gel method. But some research has shown that the sol-gel method easily reduced the loading performances of TiO2, such as distribution, combination, etc. APCVD (atmospheric pressure chemical vapor deposition) has many advantages to preparing TiO2 films, such as high bonding strength, fast reaction rate and so on [l0-13l_ In this paper, TiO2 has been loaded on cordierite porous ceramic to prepare the SCR catalyst carrier by using both APCVD and sol-gel methods. The properties of the carriers prepared by the two processes have also been compared."

Jan 1, 2011

By Anne C. Chinellato, Alejandra T. Soria, Nelida L. del Mastro, Amanda C. S. Pereiral, Esperidiana A. B. Moura, Anibal V. Abreu

"This work presents a comparative study of the thermo-mechanical and morphological properties of sugarcane bagasse fiber/HDPE composite treated with electron-beam and gamma radiation. The composite samples obtained by extrusion and injection molding processes were irradiated at 50 and 90 kGy using either a 1.5 MeV electron beam accelerator or gamma irradiator EMI-9, at room temperature in presence of air. The irradiated and non-irradiated samples were submitted to mechanical and MPI tests, differential scanning calorimetry (DSC), thermogravimetric analysis (TGA), scanning electron microscopy (SEM), sol-gel analysis and X-Rays Diffraction (XRD) and the correlation between their properties was discussed. Improvement of the bagasse fiber/HDPE composite properties, using electron-beam or gamma radiation, was found.IntroductionResidues of sugarcane bagasse fiber are widely produced in Latin America and other countries: in Southern Africa, Egypt, South-Eastern Asia, India, China, Australia, Cuba, among other producers, as by-products of the sugar and bioethanol industry. The sugarcane industry in Brazil and Uruguay is well established and expanding with large potential to increase the production of sugarcane bagasse in the next years [1-3]. Although the major portion of the bagasse is currently burnt for energy supply in the sugarcane industry, the disposal of this byproduct is still inefficient and, consequently, it is critical for agricu1ture profitability and environmental protection. Sugarcane bagasse is a lignocellu1ose fiber mainly constituted by around 46 % cellu1ose, containing hemicellu1ose, lignin, fat and waxes, silica and other elements [3, 4]. Studies have reported that sugarcane bagasse can be used to produce thermoplastic polymeric composites with excellent properties for many applications. [5-8]. Based on this survey, the transformation of bagasse into high quality industrial products, such as bagasse-polymer composites, can provide its more effective utilization."

Jan 1, 2012

By R. Padilla

In most of the Chilean copper and gold concentrates, arsenic is present mainly as enargite, Cu3AsS4, which at the conventional roasting or smelting temperatures decomposes liberating arsenic as gaseous compounds. The objective of this investigation was to study the decomposition reaction of enargite in an inert atmosphere in the range of 500 °C - 750°C. The results obtained indicated that the decomposition begins at about 525 °C. Two distinct regions in the temperature dependence of the decomposition rate were observed: a low temperature region between 525 °C to 650°C and a high temperature region between 650 °C to 725 °C. The X-ray diffraction analysis suggests that the decomposition of enargite occurs through the formation of intermediate tenantite, according to the following sequential reactions: 4Cu3AsS4(s) ? Cu12 As4S13(s)+ 3/2S2(g) Cu12 AS4S13(s) ? 6Cu2S(s) + 2As2S3(g) + 1/2S2(g) The decomposition kinetics was analyzed by using the model for a topochemical reaction of spherical particles: 1-(1-X) 1/3 = kt, which represented well the data. Apparent activation energies of 113 kJ/mol and 60.5 kJ/mol were found for the low and high temperature regions, respectively.

Jan 1, 1999

By Kunihiko Takeda, Kimio Imaizumi, Tsuyoshi Arai

"The study on the preparation of mono-dispersed liquid droplet was performed using ultrasonic as one of the steps of producing the perfectly mono-dispersed particle. The ultrasonic system was a 33.6kHz ultrasonic generator, an amplifier, an electric distortion element, and a bolted Langevin type horn installed in .a cell. For the first time, a liquid pillar under a nozzle of the cell ·was stably formed. Then, dense and coarse parts were alternatively constructed by oscillating the wavelength of the ultrasonic.· The diameter of those liquid droplets were found to be· perfectly uniform, therefore, it was measured by ""multiplex photography"" using a synchronized stroboscope with the ultrasonic.- From the results, more than 30,000 of perfectly uniform liquid droplets in 1 second were observed by this method.IntroductionRecently, research on the control of physical form is done in various fields of industry. Some examples are the processing technology of the minute compound material of micro-machines and integrated circuits, and the form control of molecule size like catalysts. There is a need for such material to take on various forms in correspondence to its use. ""Form control"" as used in this study will indicate ""research on physical chemistry factors which determine the size of the material"" and will refer to the contour uniformity of comparatively little particles. A well-known method of preparing particles is to spout a mist of liquid and slurry from a nozzle l) 2). Particles for metals, catalysts and food have been prepared by this method. In this case, although an approximate particle diameter can be decided by controlling the nozzle diameter and the violent outflow velocity, it is not easy to completely control ·the contour and to prepare a particle with uniform diameter. ·However, the preparation of perfectly uniform particles is necessary for solders for the adhesion of electronic wiring 3), ion exchange resins4), catalysts and so on. Large quantities of fine particles and super-fine particles are generated when manufactured in the usual way. Large quantities of these fine· particles and super-fine particles have polluted the internal and external' environments of factories. The products yield' ·decreases, also. From such a background, this study examines the preparation of perfectly uniform particles that could be· collected -100% as products. Recently, NASA has succeeded in the preparation of perfectly uniform particles in zero gravity 5). But the preparation of 'perfectly uniform particles by this method is difficult, and it can not be used in general industry"

Jan 1, 2000

By Beatriz Ribeiro Nogueira, Vijaya Kumar Rangari, Esperidiana A. B. Moura, Anne Chinellat, Arifa Parveen, Angel Visentim Ortiz

"Composite consisting of ethylene vinyl alcohol (EVOH) with short piassava fibers were prepared by extrusion process and their thermal and morphological behavior were investigated. The EVOH reinforced with 5 and 10 % of pi as sa va (Attaleafunifera Mart) fiber particle, based on the percentage weight ratio (wt %), untreated and treated with a commercial silane coupling agent, were prepared and the influence of fiber loading and the effect of chemical treatment on their thermal and morphological behavior were evaluated by SEM, DSC and TG analyses. Melt flow index (MFI) of the composites have been determined to evaluate the effects of fiber reinforcement on dynamic viscoelastic melt of the EVOH. In addition, piassava fibers characterization by SEM, FTIR, and organic and inorganic composition have also been carried out. The SEM results of the composites showed surface micrographs without microvoids and a good distribution, dispersion and compatibility between the fillers and the EVOH matrix. Concerning the piassava fibers characterization, the results showed that piassava has higher lignin content than cellulose and hemicelluloses, and around 0.7 % of ash with 52 % of silica (Si02). This high concentration of silica is consistent with the SEM analysis of the fiber that showed a large amount of ""silica rings"" encrusted on their surface.IntroductionLately, great worldwide interest has arisen in developing new technologies that enable the use of products with less environmental impact. Effort has been put into seeking natural modifier applications, particularly regarding the use of natural fibers. Special attention has been given to the use of natural vegetable fibers, because of the huge variety of species available. Such vegetable fibers are usually referred to as lignocellulosic materials [1]. This work evaluated the effects of piassava (Attalea funifera Mart.) fiber incorporation in an ethylene and vinyl alcohol copolymer (EVOH). The EVOH belongs to a family of copolymers with excellent gas barrier properties and resistance to organic compounds, which allow its application in different segments, from food packaging to gas tanks. However, EVOH is very sensitive to moisture, and in conditions of high humidity its gas barrier properties, thermal and mechanical properties are affected."

Jan 1, 2012

By Mingming Zhang, Mallikharjuna R. Bogala, Ramana G. Reddy

Steelmaking desulfurization slag samples were characterized using chemical, X-ray diffraction (XRD), scanning electron microscopy (SEM) and energy dispersive spectrometry (EDS) methods. The objective of this work is to investigate the occurrence of sulfur and phosphorus components in the slag samples and to identify their origin and associations with the iron phases. Thermodynamic calculations results confirm the presence of phosphorus and sulfur components in the slag sample at high temperatures (1400 to 1800oC). The main constituents of slag include Ca3SiO5 (28.1%), MgO (9.31%), Ca3(PO4)2 (9.18%), CaS (8.39%) and CaO (5.68%). The major phosphorus and sulfur components of the slag are Ca3PO4 (99.2%) and CaS (79.3%) respectively. Characterization studies indicate the presence of microparticles of different sizes and shapes in the slag sample. Elemental analysis of these particles confirm the presence of major elements (O, Mg, Al, Si, S, Ca and Fe) in the slag sample.

Jan 1, 2015

By J. W. Bridge

Triaxial compression tests at various confining pressures and temperatures, as well as tangent modulus tests using ultrasonic waves, were conducted for wax-coated granular composite materials. The material used is a surface for Thoroughbred horse racing. The purpose of these tests is to examine how track shear strength and tangent modulus at a range of loads respond to changing temperatures. Previous work has shown that a wide range of operational temperatures are experienced which have been reproduced in the lab. Using differential scanning calorimetry, it is confirmed that these operational temperatures correspond to distinct thermal transition regions for the wax that is used to coat the sand in these surfaces. Preliminary results show that both shear strength and tangent modulus are sensitive to temperature changes with maximum strength and modulus correlating with major DSC wax transition regions.

Jan 1, 2010

By Jewel Andrew Gomes

Arsenic is considered as one of the toxic materials being controlled by Environmental Protection Agencies in several developed and developing countries. It is found in the nature as constituents of the soil, minerals and also in various organic forms. It enters the air, water, and land from wind-blown dust and gets into water from runoff, leaching, soil erosion and anthropogenically from chemicals used for wood preservation, insecticides, medicine, military purpose, pigments, and electronic circuitries. There are several techniques available for removal of Arsenic, such as coagulation/filtration, lime softening, ion exchange, reverse osmosis, nanofiltration, wet chemical, and electrochemical. Electrocoagulation has been found as one of the most efficient techniques to remove inorganic arsenic with more than 99% efficiency. In this paper, we present our work on electrochemical treatment of both the inorganic and organic arsenic from water using various sacrificial electrode materials, i.e., iron, aluminum, copper, and combination of them. The floc produced by this method has been also characterized using XRD, SEM/EDS, FTIR, and cyclic voltammetry.

Jan 1, 2010

By Hiroshi Nakazawa

An acid mine drainage in abandoned Horobetsu mine in Hokkaido, Japan, contains arsenic and iron ions; total arsenic ca.10ppm, As(III) ca. 8.5ppm, total iron 379ppm, ferrous iron 266ppm, pH1.8. Arsenic occurs mostly as arsenite (As (III)) or arsenate (As (V)) in natural water. As(III) is more difficult to be remove than As(V), and it is necessary to oxidize As(III) to As(V) for effective removal. 5mL of the mine drainage or its filtrate through the membrane filter (pore size 0.45m) were added to arsenite solutions (pH1.8) with the concentration of 5ppm. After the incubation of 30 days, As(III) was oxidized completely with the addition of the mine drainage while the oxidation did not occur with the addition of filtrate, indicating the microbial oxidation of As(III). In this paper, we have investigated the microbial oxidation of As(III) in acid water below pH2.0.

Jan 1, 2006

By Preston C. Holloway

Transformational roasting involves the heating of a material along with specific additives to induce mineralogical changes in the starting material. By controlling the chemical composition, roasting atmosphere, temperature and time of reaction, the mineral transformations induced during roasting can be engineered to control the distribution of valuable, or harmful, metals and to produce new mineral assemblages that are more amenable to conventional methods of metals recovery or to environmentally safe disposal. To date, this type of process has only been applied to the recovery of a limited number of metals, but current research is looking to expand the application of these techniques to the recovery of metals from a wider range of materials. An introduction to these techniques is presented along with preliminary results from their application to metals recovery from zinc bearing wastes, such as zinc ferrite leach residues and carbon steel electric arc furnace dust.

Jan 1, 2006

By J. F. Elliott

The thermodynamic behavior of sulfur and oxygen in copper matte has been measured by equilibration of the melt 00 a gas consisting of CO, SO2 and Ar. The oxygen potential ranges from 10-9 to 10-7 and that for sulfur from 10-4 to 10-2 atm. The work is a continuation of the earlier study by Luraschi and Elliott in our laboratory. A model has been developed that permits extra-polation of the results to ascertain compositions of the matte that are saturated with various oxides of iron.

Jan 1, 1983

By Leiting Shen

The thermodynamics of tungsten ore decomposition in mineral acid and alkaline solutions were studied. The published thermodynamic data of tungsten minerals were collected and assessed. The Gibbs energies of CaWO4 (−1538.43 kJ/mol), FeWO4 (−1053.91 kJ/mol), MnWO4 (−1206.08 kJ/mol), H2WO4 (−1003.92 kJ/ mol), and Na2WO4 (−1455.58 kJ/mol, aq) at 25 °C were adopted in the calculation using HSC software. The results show that CaWO4 is decomposed more readily in Na2CO3 solution than in NaOH,while FeWO4 andMnWO4 aremore reactive inNaOH solutions. Froma thermodynamic point of view, tungsten ore decomposes easily in acid solutions despite most ΔGo T increasing slightly with temperature. Oxidizing Fe2+ to Fe3+ in acidic solutions facilitates decomposition of FeWO4, and the reaction of CaWO4 in H2SO4 solution occurs more easily than in other mineral acids, due to the formation of sparsely soluble CaSO4. The results fit well with the experimental data and industrial experience previously reported in the literature.

By Shadia J. Ikhmayies

"Nanocrystalline fluorine doped tin oxide (Sn02:F) thin films were produced by the spray pyrolysis technique (SP) on glass substrates at a substrate temperature T, = 450 ° C. The hydrated stannous chloride (SnClz.2H20) was used as a precursor and ammonium fluoride (NH4F) and hydrofluoric acid (HF) were used as the doping compounds. A comparison between the compositional, morphological and optical properties of the films obtained by using the two doping compounds was performed by using scanning electron microscope (SEM) observations, energy dispersive spectroscopy by X-rays (EDAX) and transmittance measurements. It is found that the films prepared by using HF have larger grain size, and higher fluorine content than the films prepared by using ~- In addition these films have higher transmittance and higher direct optical bandgap energy. These results are interesting for the use of Sn02:F as a forecontact in CdS/CdTe solar cells.IntroductionTin dioxide is an n-type, wide bandgap semiconductor (about 3.5 eV) and in the form of thin films, it is a transparent conducting material, characterized by high optical transmission (80- 90%) [l]. Sn02:F is the most widely used transparent-conducting oxide material. The transparent-conducting thin films of this oxide are used as electrodes in a variety of optoelectronic devices, as heat mirror coatings in 'smart windows' for buildings, in automobile and airplane windshields, in incandescent light bulbs, in flat-plate and concentrating solar collectors. Tin oxide and zinc oxide, in thin film configuration are technologically important materials because of their applications in photovoltaic cells [2].Among various dopants for Sn02, fluorine is often preferred, because fluorine doping results in films with high transparency and good conductivity [3]. By exploring the literatures, it was found that different sources of fluorine were used to produce Sn02:F thin fihns, among which are ammonium fluoride (NH4F) and hydrofluoric acid (HF) are the most used. Some researchers used~ [2, 4-7] and others used HF [3, 6-8] for doping Sn02 films. Gordillo et al.[7] used both of NH4F and HF and showed that the resistivity of thin films obtained by using HF was lower than that of similar films obtained by using NH4F by a factor of 2.2. They also found that the films obtained by using HF have more random orientations."

Jan 1, 2013

By Lijuan Chen

During the detoxification of chromium-containing slag by Achromobacter sp. CH-1, anionic surfactant Sodium Dodecyl Sulphate(SDS) and its mixed systems with different Tween surfactants(Tween 20, Tween 60 and Tween 80) were used to promote the interaction between the bacteria and the chromiumcontaining slag and the rate of acid-soluble Cr( ? ) leached from the slag. The effects were evaluated by the surface tension, the pH of the leaching solution and the leaching rate of total Cr( ? ) from the slag. The results showed that the surfactants systems improved Cr(VI) leaching and its detoxification of chromium-containing slag. The mixed surfactants of SDS combined with Tween surfactant revealed better effectiveness of detoxification than SDS only. When the mass ratio of SDS to Tween 80 was 1:1, the rate of Cr( ? ) leached from the slag increased by 12%.

Jan 1, 2009

By Lichao Ding, Chunhua Liu, Yunnen Chen

"In this paper the simulated acid magenta dye discoloring the reaction process was researched. The results showed that it attained highest decolorization efficiency for acidic magenta simulation dye wastewater when pH 9 and reaction time 10 min. With the initial dye wastewater concentration increased, the decolored rate decreased. The decolored rate in general kept a tendency to increase with the temperature increased. Kinetics researches showed that when pH 9, reaction temperature 20 and 35 ?, the decoloring reaction process for the dyes accorded with the First-order dynamic equation. The decoloring reaction rate constant was influenced by initial concentration of dye wastewater and temperature.1. IntroductionIn China, textile printing and dyeing industry is one of industrial departments which using more water and discharging more wastewater. There is about 7 billion tons of waste water discharge each year, of which 80% from the process of printing and dyeing. Being complex ingredients, high chroma, more toxic substances and severe environment pollution, the treatment of printing and dyeing wastewater becomes problem urgent to be resolved. The traditional treatment methods such as adsorption [1], coagulation [2], biochemical method [3,4], which has advantages of simple equipment, simple operation and mature process, but they can cause waste accumulation and secondary pollution [5,6].Magenta is a kind of organic compounds, which classified into acid and alkaline magenta. Considering the advantages of simple operation, low cost, simple experiment equipment and friendly to environment, acid magenta dyes wastewater was chose as object in this paper. Some parameters such as pH, contact time, temperature and the initial concentration on of simulative acid magenta dyes wastewater were studied."

Jan 1, 2012

By Leo Brewer, Kazuyoshi Shimakage, Mamoru Mitomo, Toshiyuki Nishimura, Yoichiro Uemura, Shinji Hirai

"In the synthesis process of ß -La2S3 via the sulfurization of La2O3 powder using CS2 gas, La2O2S was formed. This occurred at an initial stage of the reaction for sulfurization temperatures below 973K, and ß -La2S3 was also formed at a shorter period for higher sulfurization temperatures. It was found that the oxygen content in ß -La2S3 powders decreased gradually with an increase in sulfurization temperature. On the other hand, the carbon content in these powders increased gradually with an increase in the sulfurization temperature. Though it has been reported that ß -La2S3 was transformed to Y -La2S3 at 1723K± 50K, the sintered compact of double-phase Y -La2S3 and ß. -La2S3 was formed at a rather higher temperature of 1973K when the synthetic powder of ß -La2S3 containing a high amount of oxygen was used. However, phase transformation of -La2S3 to Y -La2S3 progressed preferentially with a decrease in the oxygen content of synthetic ß -La2S3 powder. The Seebeck coefficient of the sintered double-phase Y -La2S3 and -La2S3 was higher than that of the single-phase Y -La2S3, reported previously.Introduction La2S3 exists in three polymorphic forms that are similar to a series of Ce2S3, Pr2S3 and Nd2S3: a, ß , and Y'. The a -La2S3, which is stable at low temperature, is irreversibly transformed to ß -La2S3 of various compositions in the solid-solution range between La2S3 and La3S4, at 923 ± 50K. The -La2S3 may also be an oxysulfide of La10S14O2. Moreover, the ß .-La2S3 phase is transformed to Y -La2S3 ,which has a Th3P4 structure, at 1573 ± 100K. The melting point of Y -La2S3 is 2398 ± 30K where this temperature is similar to those of common refractory materials such as silica and alumina. Therefore, it can be predicted that y -La2S3 which has a high melting point and a thermodynamic stability due to the strong affinity of La for S, would have &high refractory character and chemical inertness in many molten metals. The y -La2S3, colored vivid faint yellow is stable up to 623K in air, where oxidation starts. y -La2S3 is frequently used as pigments for plastics and paints3. Furthermore, Y -La2S3 which is a semiconductor, is considered to be useful as a thermoelectric conversion materials, because it has a high Seebeck coefficient."

Jan 1, 2000

By Gus Van Weert

Hydrometallurgical oxidation of sulphides is capital and energy intensive, with autoclave and bio-technology competing for lowest overall cost status. The use of surface aerators instead of stirred tank reactors could provide lower costs for bio-oxidation of concentrates. With this in mind, the Delft Inclined Plate reactor was designed with inclined plates above a settler shaped reactor to continuously return slurry from the lowest point in the settler to the surface of the liquid. The multiplate superstructure overcomes the scale-up restriction of the standard circular surface aeration patterns. DIP aerator energy and volume requirements for oxygen transfer from air will be presented in terms of kg O2/kWh and kg O2/m3/h transferred as a function of wt % sand in the slurry and compared to stirred tank performance. Scale up from the 4 m3 pilot unit will be discussed.

Jan 1, 1996

By Lei Zhang, Shining Chen, Lina Wang, Pu Liu, Benquan Fu, Jiannyang Hwang

A PFS(polymeric ferric sulfate) coagulation-photocatalytic oxidation technology was used for advanced treatment of coking wastewater from secondary biological treatment. Effects of some key factors on TOC removal rate were investigated, and the results were compared with those of the common photocatalytic oxidation technology under the operating parameters of the photocatalytic oxidation defined. Single factor experimental results showed that TOC removal rate could reach 81%, when optimal operating conditions were as follows: TiO2 loading: 4.0g/L, irradiation time: 4h, initial pH is 5.1and PFS dosage:700mg/L. PFS coagulation and photocatalytic oxidation have synergistic effect, which is meaningful for highly efficient treatment of coking wastewater

Jan 1, 2015

By Xiaowen Liu

The thermal decomposition of diaspore was investigated by thermogravimetry (TG),differential scanning calorimetry (DSC), X-ray power diffraction(XRD),infrared (IR)spectrain this paper. The thermal decomposition mechanism of diaspore was discussed according to Coat-Redfer equation. It was found that the decomposition of diaspore was carried out at 500?,and the peak temperature was 530?. The electrovalent balance of diaspore was destroyed. The previous crystal structure was changed. a- Al2O3 was obtained after thermal decomposition. The activation energy is 287KJ/mol.

Jan 1, 2006

By Alberto Oalvez, Lucya Yunus, Pengfii Tan

"Laboratory flotation tests of slow cooled converter slag have showed that 92.5% copper recovery at the copper cut-off grade of 24 - 25 % can be achieved by using a 50:50 ratio of DSP330 and SIBX (sodium isobutyl xanthate) at the natural pH of 7 and with a grinding time of 18.5 minutes. 70ìéç is the P80 achieved at this grinding time. MIBC is the frother and the solid content of the flotation feed was 46%. In the plant trials, two types of collectors at two different feed particle sizes for both the normal and slow cooled slag were operated. The particle size was controlled by the feed rate. The P80 of 75 ìçé at a feed rate between 32 - 36 t/h were tested. The plant trials have demonstrated that the copper recovery in the milling and flotation process of the slow cooled slags was improved by 3%. IntroductionIt is proposed to float the slow cooled converter slag, in the auxiliary circuit of the copper concentrator at Mount Isa, by using the processing conditions identified from several laboratory flotation tests. Among these laboratory tests, one produced a copper recovery of 4 % higher than those achieved from a normal cooled slag with the same slag feed grade and the same copper content (24 - 26 %) in the concentrate. These test conditions were selected for further studies.Laboratory Test Work and Plant TrialsThere has been a lot of work conducted under laboratory and plant conditions [1]. However, the achieved results did not justify their total implementation in the Mount Isa Copper Concentrator. Initially, the lab trials were carried out with slag cooled 100% in air; then it was changed to combined cooling for 12 h with air and 2.5 days with water sprays. The reason for this change was the shortage of space when the slag was cooled 100% in air, as it takes several days to achieve safe temperatures for its removal. The San Manuel Copper Smelter has reported that their slag was left for air cooling in pits for 8 h and then was followed by water cooling for 2-3 days [2]"

Jan 1, 2012