Search Documents

By Bing Li, Miao Shen, Qiang Wang, Yuqi Chen

Electrochemical methods including cyclic voltammograms, square wave voltammograms, chronopotentiometry are applied to characterize the reduction potentials of Na+ and Li+ ions in LiCl-KCl melts. According to theoretical calculation, the reduction potential for Na+ is slightly more negative than Li+ in NaCl-LiCl-KCl melts at 450℃. However, by electrochemical measurements, the reduction potential of Na+ is slightly more positive than Li+ in the above melt and the potential difference between Na+ and Li+ reaches 0.16-0.2V on an inert W electrode in 1.0-2.0 wt% NaCl-LiCl-KCl melts. An active Pb electrode is used to improve the removal rate of Na+ from LiCl-KCl melts. The reduction potentials for both Na+ ions and Li+ ions on a Pb electrode shift to more positive values and the reduction currents become larger. After 6h electrolysis on a Pb electrode at -3.0V, the practical removal efficiency of Na+ ions reaches 90.12% and the reduced products contain metallic Na and Li with a Na/Li mass ratio of 4.25/1.

Jan 1, 2015

By Sung-Joo Lee, Gi-Chon Han, Nam-Il Um, Hee-Chan Cho

"In Korea, almost all of bottom ash produced by coal power plants is disposed of in ash ponds. Ash storage areas comprise more than 80% of most coal power plant sites. This disposal method is causing environmental problems and a managerial burden for plant operators. In this study, investigations to develop a beneficiation process for separating coal pond ash into various products were undertaken. To improve efficiency of the separation, coal ash was separated by sizes and each size fraction was subject to various beneficiation processes. The separation process used were flotation (-200 mesh size), hindered settling (16x200) and tabling (16x200 and 8x16 mesh). The results showed that various marketable products, such as lightweight aggregate, sand, high-carbon fuel, could be recovered from coal pond ash using simple physical separation techniques.IntroductionDue to the increased use of coals every year, about fifty million ton of coals were used in 2007 alone. As a result, about 6 million tons of coal ash were generated. In Korea, the coal bottom ash is classified as a general industrial waste and is usually disposed of in ash ponds. The costs for this disposal method continue to increase due to rising costs of site management and development and more strict environmental regulation. Therefore, utilities are constantly looking for ways to increase utilization of coal ash. In this study, various beneficiation processes were evaluated to examine the possibility of separating coal pond ash into various products which can be used as aggregates and high-carbon fuel."

Jan 1, 2008

By R. M. Reynolds

Engitec Impianti, S?.p.A. of Milan, Italy has successfully designed, constructed and has in operation state-of-the-art battery breaker systems at two European locations. A third facility i:s partially completed in Toronto, Ontario, Canada. The CX system crushes whole batteries, separates the various components and desulfurizes the battery paste. The system also produces sodium sulfate from the sulfuric acid and lead sulfate contained in the batteries. Actual plant operating data indicates that the desulfurized paste contains less than 0. 6 percent sulfur and less than 0. 5 percent antimony. The CX system utilizes mechanical screening and an up-flow hydrodynamic separator to accomplish the component separation. Sodiwn hydroxide or sodium carbonate is used for desulfurization. The sodium sulfate brine is evaporated and crystallized to produce clean anhydrous sodium sulfate suitable for use by detergent or glass manufacturers. Plant data also indicates that an increase in furnace productivity of about 25 to 30 percent is achieved using feed from the CX system. The desulfurized paste is very suitable for electrolytic processing as an alternative to pyrometallurqical processing.

Jan 1, 1990

By C. J. Malek

The CONTOP® smelting cyclone technology is a large-scale and time-proven method which in combination with other technologies (grinding, drying, pyrolysis, etc.) provides for a cost- efficient and ecological disposal of a wide range of waste materials from industry and households. In this report the basic principle of smelting cyclone technology will be explained first. Subsequently, the paper will discuss substantial concepts for the recovery of various remainders.

Jan 1, 1996

By M. K. Alam

Chemical Vapor Deposition (CVD) processes are currently attracting special attention in materials processing. CVD processes are now used to produce special materials in the form of thin films, coatings, composites, and optical fibers. This process produces material of high purity, in complex shapes, and in a variety of microstructures. It is a capital intensive process, involving use of high cost raw materials. Modeling simulations have the potential of reducing the time for CVD . process design, and the need for experimentation. Modeling would, therefore, appear to be an attractive option for producing a product of acceptable quality. At Ohio University, progress has been made in modeling of CVD processes, specially in the areas of optical fiber preform fabrication, and fiber coating.

Jan 1, 1990

By W. William Culver

James Douglas became known in the nineteenth century for two reasons fundamental to his mining career: (1) his experimental work with copper hydrometallurgy, and (2) his grasp of the idea that the quantity of copper ore matters more than the quality. On the first reason, there is a moment for any technology that’s critically important—when it moves from an area of scientific interest to one that companies are founded on. This paper examines the original 1869 Hunt and Douglas Copper Process in the context of science and engineering as they were in the 1860 and 1870s. It was a “humid” process, developed at Quebec’s Harvey Hill Mine. Chemically, the Hunt and Douglas vat leaching process succeeded, but not the original companies using it. On Douglas’ understanding of ore quality versus quantity, luck had it that the first company to field test the Hunt and Douglas Copper Process was in Chile. The Hunt and Douglas patent made that transition from experimental model to operational plant in 1870 when the Compañia de Minas de la Invernada was organized in Valparaíso. As a joint-stock company, Invernada spread the risk of investing in the revolutionary, but untested, Hunt and Douglas Process. The company brought Douglas to Chile as a consultant in 1871. His experience with hydrometallurgy, combined with what he learned about the copper business while in Chile, set him off on a career in metal mining that both surprised Douglas and made him wealthy.

By Taner Kavas

The refractory bricks of a rotary cement furnace containing of alumina and magnesium chromite were studied in order to determine whether they could be used in the concrete production as aggregates. Three mortars were prepared by mixing 1 part cement, 3 part aggregate materials, 0.5 part water by weight and mechanical, chemical, thermomechanical and microstructural characteristics were evaluated. The compressive and bending strength of samples were determined after 2 and 28 days curing. Resistance to chemicals were established by calculating the weight gain of mortars stored in 2 % HCl solution for 1 h and 24 h. Thermomechanical characteristics were determined by measuring the compressive strength of heat treated specimens at temperatures of 400 °C, 600 °C and 800 °C. Consequently, magnesium chromite containing waste brick aggregates have given the best results.

Jan 1, 2006

By Kandipati Sreenivasarao

Ion flotation is a promising separation process for continuously removing toxic metal ions from dilute process effluents. After treating the effluent with appropriate surfactant(s), the metal- bearing species adsorb onto the surface of rising gas bubbles and can be collected as foams. Suitable collectors have been identified for most of the elements of the periodic table. However, a better understanding of the thermodynamic, kinetic and engineering principles that determine the performance of ion flotation systems would facilitate commercial utilization of this technology. A model system of sodium dodecylsulfate-ethanol has been studied for the removal of Cu (11) from dilute solutions, using laboratory-scale flotation columns. This paper reports the effects of the air flow rate, solution height, foam drainage zone height and col1ector:metal ion ratio on the flotation kinetics, ultimate recovery of metal, flotation product grade, foam losses and effluent quality. Preliminary results for Pb (11) removal are also reported.

Jan 1, 1993

By Milton Manrique

The thermal decomposition of ilmenite concentrates in a non-transferred arc; thermal plasma flow reactor was investigated. The plasma torch was operated using argon-helium and argon-nitrogen mixtures as plasma gases. The effect of power, feed rate and particle size was studied. Products were characterized by XRD, SEM, TEM and ICP techniques. Free energy minimization plots were used to predict the thermodynamic behavior of the system under different operating conditions. The results of this investigation showed a significant segregation process where titanium-rich products are collected in the reactor, while iron-rich products are collected in the quenching box and filter. The average size of the product is in the sub- micron range. Titanium nitride was formed and condensed in the reactor zone when using an argon-nitrogen mixture as the plasma gas.

Jan 1, 1998

By Toshia Suzuki, Keiji Kakudate, Yoshihiro Adachi

"A macro model for the steel usage pattern in Japan is proposed. The steels are classified into four types; converter steel for machinery and for construction and electric furnace (EF) steel for machinery and for construction. The steels are assumed to be discharged from the society in accordance with lifetime distributions of each usage. The amount of EF steel and the accumulation in society are calculated using a population balance model. The comparison with the calculated results and statistics ensures the validity of the model. Since the amount of EF steel for construction will increase and be oversupplied, EF steel will have to be used for machinery. The required and available amounts to supply EF steel for machinery are considered from the point of allowable· copper concentration for machinery use. Copper contaminates steel used for machinery during recycling process and contamination ratio is evaluated with the model. Copper concentration in EF steel is predicted for various scenarios.IntroductionThe amount of CO2 emission from Japanese steel industry is 48.0 million C-ton in 1990 and it occupies 15.1% of the total amount in Japan. In order to reduce the C02 emission and to save the natural resources, it is strongly required to promote the recycling of steel. However, the impurity contaminates steel in recycling process and lowers its quality. The copper concentration in EF steel is analyzed by Toi et al. using a macro model with the assumption that steel is discharged in proportion to the accumulation amount [1]. However the discharged amount of products is dependent on their age for service and usage pattern and not on the accumulation amount. In addition, the degree of copper contamination is different depending on the usage of steel. Therefore a precise model that contains the age for service within the society as a parameter and distinguishes the usage· of steel is necessary in order to clarify the problems in the recycling of steel."

Jan 1, 2000

By Jerome P. Downey

Technologies developed within the field of extractive metallurgy to recover, concentrate, and purify metals and industrial minerals from ores, have served as the foundation for all of the subsequent environmental remediation, materials recycling, and waste management technologies. This paper discusses the application of classical extractive engineering principles to the development of a thermal process for the recovery of mercury from solid wastes. Process development is presented as a series of logical stages, which begin with a thorough characterization of the site-specific waste, move on to bench and pilot scale testing of the process options, and end with a functional process flowsheet. This paper also presents thermodynamic data on many mercury species of interest to the minerals, power, and chemical industries. These data can be used to model the speciation and recovery of the mercury as a function of various process parameters.

Jan 1, 2003

By Ross R. Bhappu

Anticipating a major power cost increase in 1990, Cyprus Copper Company decided to modernize the Miami Smelter at a cost of $92.5 million. The modernization project included the addition of an Isasmelt vessel for use as the primary copper smelter and the modification of the existing electric furnace to a slaglmatte separating vessel. The project was completed in June of 1992 and is currently operating at close to its design capacity. This paper provides a summary of the decision making process, a description of the project, a summary of start-up problems and solutions and the current status of the smelter operation.

Jan 1, 1994

By Liangju He, Peixuan Ouyang, Peijie Li

Single-pulse laser ablation of aluminum and titanium alloys under glass confinement is investigated. Processing parameters such as laser intensity and gap width between targets and glass are varied. Surface morphologies and crater profiles of the alloys after laser ablation are studied by SEM and white-light interferometric microscope, respectively. The effects of gap width and laser intensity on surface morphologies and crater profiles of targets are systematically analyzed. In addition, the generation of porous surface structures in Ti target is regarded as the result of phase explosion in the molten surface layer of targets and the thermodynamic condition in our experiment for phase explosion is evaluated.

Jan 1, 2016

By J. P. R. deVilliers

A procedure is described whereby gold-containing calcined concentrates and leach residues from refractory gold ores are smelted with carbon to form a small amount of metal. The gold is liberated upon smelting, and is collected in the molten metallic phase, which is easily separable from the slag. The metallic phase consists of approximately 1 to 15 per cent (by mass) of the material after smelting, and the gold content is generally upgraded by a factor of greater than 6 compared with that of the original roasted material. Recoveries better than 95% have routinely been achieved. The quenched metal contains predominant Fe-Ni alloy, as well as minor Fe sulphides and Cu-Fe sulphides. Trace amounts of Fe-Ni arsenide and Au-Cu alloy are also present. The gold content of the metallic phase can be increased further by oxidation of the hot metal in the presence of silica or slag. This will reduce the amount of metal, and will concentrate the gold in a smaller volume. The metallic phase can then be treated hydrometallurgically to recover the nickel and the gold.

Jan 1, 1989

By Junfu Chen, Jiann-Yang Hwang, Yong Zhou, Lijun Lu, Likun Lia, Jixiong Liu

The sheet-like NiS-ZnS heterostructured composites were prepared by the microwave hydrothermal. The fabrication of the heterojunctions broadened the range of light response of ZnS. The photoexcited electrons of ZnS migrated to the redox potential of NiS/Ni2S under visible light irradiation, which can facilitate the effective separation of photogenerated electrons and holes in space. The visible photocatalytic activity towards hydrogen production for NiS/ZnS nanosheet heterostructed composites without co-catalyst achieved 0.28 mmol h–1, and the quantum efficiency was up to 18.6% under the wavelength with 420 nm visible light irradiation.

Jan 1, 2015

By R. M. Westcott

A two-electrode, direct current, slag resistance furnace (SRF) has been constructed and operated to selectively reduce the zinc and lead contents of non-ferrous slags. The experimental SRF is equipped with multiple methods of gas/solids injection for both mixing and reaction. A computer is used to position the electrodes and for data acquisition. A geometric factor correlation was previously developed at Columbia University for calculating the electrical resistance on the basis of furnace geometry and slag conductivity. The experimental SRF was used to test this correlation.

Jan 1, 1994

By Lanre Oshinowo

Computational Fluid Dynamics (CFD) is used in conjunction with process modelling at HATCH to achieve a superior level of confidence in the process design of hydrometallurgical process plants. The use of these tools to evaluate designs through virtual prototyping reduces the risks associated with making design decisions. This paper highlights the development of a co-simulation strategy at Hatch for the seamless integration of process modeling software addressing different scales (process time and space): flowsheet level models and .equipment level models. With co-simulation, the process design engineers can improve design accuracy, troubleshoot and optimize performance and influence decisions impacting equipment operation by representing specific unit operations in the flowsheet model software with detailed CFD models. Specifically, this paper will focus on the co-simulation of a Ni/Co high-pressure acid leach (HPAL) process including heaters/heat exchangers and flash system, autoclave and quench/scrubber system. The knowledge developed can be transferable to other processes.

Jan 1, 2004

By S. S. Babu, T. Hong, T. DebRoy, S. A. David

"Oxide inclusions form in welds because of deoxidation reactions in the weld pool. These inclusions control the weld microstructure development. Thermodynamic and kinetic calculation of oxidation reaction can describe inclusion characteristics such as number density, size, and composition. Experimental work has shown that fluid-flow velocity gradients in the weld pool can accelerate inclusion growth by collision and coalescence. Moreover, fluid flow in welds can transport inclusions to different temperature regions that may lead to repeated dissolution and growth of inclusions. These phenomena are being studied with the help of computational coupled heat transfer, fluid-flow, thermodynamic, and kinetic models. The results show that the inclusion formation in steel welds can be described as a function of the welding processes, process parameters, and steel composition.IntroductionThe relationship between inclusions and formation of a high-toughness phase, namely acicular ferrite in low-alloy steel welds, is well known (1-4). Past research has focused on maximizing acicular ferrite amount in welds by controlling welding processes, process variables, and welding consumable parameters. Research has shown that there is a complex interaction between inclusion characteristics, prior austenite grain size, and weld metal hardenability. In a low-alloy steel weld, the small addition of titanium lead to a change in the inclusion composition and resulted in a transition in the microstructure from bainitic to acicular ferrite [see Fig. I]. This in turn lead to the best combination of strength and toughness. This paper describes the inclusion formation in low-alloy steel welds."

Jan 1, 1999

By Jiao Li, WenhuiMa, KuixianWei, YongnianDai, Cong Zhang

The paper studied the diffusion process of nitrogen and characteristic distribution of iron impurities in the bottom of cast crystalline silicon ingot along the direction of crystal growth. According to the dynamics analysis of the decomposition of Si3N4 coating, the diffusion process of nitrogen into multicrystalline silicon ingot during casting process should be divided into three steps. The diffusion length of nitrogen in multicrystalline silicon ingot is 700 μm. The results of EDS analysis indicate that the distribution characteristic of iron in multicrystalline silicon ingot is concerned with the diffusion process of nitrogen in this length. Based on the above research results, the distribution model of iron in casting multicrystalline silicon ingot was established and verified by the experimental results.

Jan 1, 2015

By F. Mucciardi

While flash smelting and converting are capturing a greater share of the market, injection through circular injectors will remain with us for the foreseeable future. The use of top lances for injection is a key feature in several processes (e.g. Mitsubishi, Ausmelt). Tuyeres, on the other hand, are incorporated into a number of processes (e.g. Noranda, Peirce-Smith). To date no lances or tuyeres are cooled by an external source. The reagent provides the bulk of the cooling. With limited cooling, it is normal to have substantial wear on the nozzles - especially in the case of lances. To overcome the issue of wear, a new patented injector (lance or tuyere) has been developed by Noranda and McGill University. This novel unit is based on heat pipe technology. It can operate for an extended period of time without wearing. Enhanced lance/tuyere life is achieved by operating the injector at a low enough temperature that promotes the formation of a thin frozen layer on the outer body of the unit. The vaporizing and condensing substance within the unit acts to cool' the high heat flux portions and dissipate the heat to areas of low heat flux outside the vessel. A fairly large number of tests have been conducted with a prototype unit. The tests have shown that the heat pipe lance is a viable unit. In this paper is detailed a test which illustrates how the lance functions when pure oxygen is injected into copper matte. In addition, the findings from a basic study of a heat pipe in high heat flux environments are also presented.

Jan 1, 1999